Text preview for : sony_MDX-C6400R_service_manual.pdf part of Sony MDX-C6400R MDX-C6400R/C6500R/C6500RX FMFM/MW/LW MINIDISC PLAYER Car Audio
Service Manual
Back to : sony_MDX-C6400R_service_m | Home
MDX-C6400R/C6500R/C6500RX
SERVICE MANUAL
Ver 1.2 2001.12
AEP Model
MDX-C6400R/C6500R/C6500RX
UK Model
MDX-C6500R/C6500RX
Photo: MDX-C6500R
Model Name Using Similar Mechanism Base Mechanism Type Optical Pick-up Name
NEW MG-164NZ-138 KMS-241C
SPECIFICATIONS
MD player section
Signal-to-noise ratio Frequency response Wow and flutter 90 dB 10 20,000 Hz Below measurable limit
General
Outputs Audio outputs*1 Power aerial relay control lead Power amplifier control lead Telephone ATT control lead*2 Bass ±9 dB at 100 Hz Treble ±9 dB at 10 kHz 12 V DC car battery (negative ground) Approx. 178 × 50 × 183 mm (w/h/d) Approx. 182 × 53 × 162 mm (w/h/d) Approx. 1.2 kg Parts for installation and connections (1 set) Front panel case (1)
Tuner section
FM
Tuning range Aerial terminal Intermediate frequency Usable sensitivity Selectivity Signal-to-noise ratio 87.5 108.0 MHz External aerial connector 10.7 MHz/450 kHz 8 dBf 75 dB at 400 kHz 66 dB (stereo), 72 dB (mono) Harmonic distortion at 1 kHz 0.6 % (stereo), 0.3 % (mono) Separation 35 dB at 1 kHz Frequency response 30 15,000 Hz Tone controls Power requirements Dimensions Mounting dimensions Mass Supplied accessories
MW/LW
Tuning range Aerial terminal Intermediate frequency Sensitivity MW: 531 1,602 kHz LW: 153 279 kHz External aerial connector 10.7 MHz/450 kHz MW: 30 µV LW: 40 µV
*1 Equipped with front and rear outputs: MDX-C6500RX/C6500R only Equipped with rear outputs: MDX-C6400R *2 MDX-C6500RX/C6500R only U.S. and foreign patents licensed from Dolby laboratories Licensing Corporation. Design and specifications are subject to change without notice.
Power amplifier section
Outputs Speaker outputs (sure seal connectors) Speaker impedance 4 8 ohms Maximum power output 50 W × 4 (at 4 ohms)
FM/MW/LW MINIDISC PLAYER
9-870-051-13
2001L0500-1 C 2001.12
Sony Corporation
e Vehicle Company Published by Sony Engineering Corporation
TABLE OF CONTENTS 1. GENERAL
Location of controls ........................................................ 3 Installation ....................................................................... 4 Connections ..................................................................... 5
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. NOTES ON LASER DIODE EMISSION CHECK Never look into the laser diode emission from right avove when checking it for adustment. It is feared that you will lose your sight. NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK (KMS-241C/J1NP). The laser diode in the optical pick-up block may suffer electrostatic break-down easily. When handling it, perform soldering bridge to the laser-tap on the flexible board. Also perform m easures against electrostatic break-down sufficiently before the operation. The flexible board is easily damaged and should be handled with care.
2. 3.
DISASSEMBLY ......................................................... 9 ELECTRICAL ADJUSTMENTS
Test Mode ........................................................................ 16 MD Section ..................................................................... 16 Tuner Section .................................................................. 16
4.
4-1. 4-2. 4-3. 4-4. 4-5. 4-6.
DIAGRAMS
Block Diagram SERVO Section ............................... Block Diagram TUNER Section .............................. Block Diagram MAIN Section ................................. Block Diagram BUS CONTROL/ POWER SUPPLY Section ........................................... Note for Printed Wiring Boards and Schematic Diagrams ....................................................... Printed Wiring Boards SERVO Board (Component Side)/ SENSOR Board ............................................................ Printed Wiring Board SERVO Board (Conductor Side) .............................. Schematic Diagram SERVO Board (1/2) ................. Schematic Diagram SERVO Board (2/2) ................. Printed Wiring Board MAIN Board (Component Side) .............................. Printed Wiring Board MAIN Board (Conductor Side) ................................ Schematic Diagram MAIN Board (1/3) ................... Schematic Diagram MAIN Board (2/3) ................... Schematic Diagram MAIN Board (3/3) ................... Printed Wiring Board SUB Board ............................ Schematic Diagram SUB Board ............................... Printed Wiring Board KEY Board ............................ Schematic Diagram KEY Board .............................. IC Pin Function Description ........................................... 17 18 19 20 21
22 23 24 25 26 27 28 29 30 32 33 34 35 40
4-7. 4-8. 4-9. 4-10. 4-11. 4-12. 4-13. 4-14. 4-15. 4-16. 4-17. 4-18. 4-19.
laser-tap
OPTICAL PICK-UP FLEXIBLE BOARD
Notes on chip component replacement · Never reuse a disconnected chip component. · Notice that the minus side of a tantalum capacitor may be damaged by heat. Flexible Circuit Board Repairing · Keep the temperature of the soldering iron around 270 °C during repairing. · Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). · Be careful not to apply force on the conductor when soldering or unsoldering. CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
5. 6.
EXPLODED VIEWS ................................................ 50 ELECTRICAL PARTS LIST ............................... 54
SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
2
SECTION 1 GENERAL
Location of controls
This section is extracted from instruction manual.
Setting the clock
The clock uses a 24-hour digital indication. Example: To set the clock to 10:08
1
D I SC +
-P R PTY DSPL
ST
OPEN D-BASS TA
AF
Press (MENU), then press either side of (DISC/PRST) repeatedly until "CLOCK" appears.
+
MENU SOURCE SOUND
PR
ST
LIST
-SEEK/AMS
ENTER
REP SHUF
OFF
--
D ISC
MODE
1
2
3
4
5
6
1 Press (ENTER).
MDX-C6500RX/C6500R /C6400R
The hour indication flashes.
Refer to the pages listed for details. 1 Volume control dial 19 2 MENU button 8, 10, 12, 13, 14, 15, 16, 18, 19, 21, 24 3 DISC/PRST +/ (cursor up/down) buttons 8, 10, 12, 13, 14, 15, 16, 18, 19, 20, 21, 24 During CD/MD playback: Disc change 10, 13 During radio reception: Preset stations select 16 4 Z (eject) button (located on the front side of the unit behind the front panel) 9 5 DSPL/PTY (display mode change/ programme type) button 9, 10, 12, 17, 20 6 LIST button 12 List-up 13 7 SOURCE (TUNER/CD/MD) button 8, 9, 10, 13, 15, 16, 19 8 Display window 9 OPEN button 7, 9, 26 q; D-BASS button 25 qa SOUND button 23 qs Reset button (located on the front side of the unit behind the front panel) 7 qd OFF button* 7, 8, 9 * Warning when installing in a car without ACC (accessory) position on the ignition key switch Be sure to press (OFF) on the unit for two seconds to turn off the clock display after turning off the engine. When you press (OFF) only momentarily, the clock display does not turn off and this causes battery wear. qf SEEK/AMS /+ (cursor left/right) buttons 8, 10, 12, 14, 16, 18, 19, 21, 23, 24 Automatic Music Sensor 10, 14 Manual Search 10 Seek 15, 16, 18 qg ENTER button 8, 10, 12, 13, 14, 15, 16, 18, 19, 20, 21, 24 qh MODE button 19 During CD or MD playback: CD/MD unit select 9, 13 During radio reception: BAND select 15, 16 qj Receptor for the card remote commander qk Number buttons During radio reception: Preset number select 15, 16, 18, 19 During CD/MD playback: (1) REP 11 (2) SHUF 11 ql AF button 17, 18, 19 w; TA button 18, 19
2 Press either side of (DISC/PRST) to set the hour.
3 Press the (+) side of (SEEK/AMS).
The minute indication flashes. 4 Press either side of (DISC/PRST) to set the minute.
2
Press (ENTER).
The clock starts. After the clock setting is completed, the display returns to normal play mode.
Tip You can set the clock automatically with the RDS feature (see page 17). Note In the initial setting, the clock indication appears while the unit is turned off. When the D.INFO mode is set to ON, the time is always displayed (page 24).
3
4
5
6
7
8
SECTION 2 DISASSEMBLY
Note: Follow the disassembly procedure in the numerical order given.
SUB PANEL ASS'Y
1 screw (PTT2.6 × 5)
2 cover
4 two claws
5 sub panel ass'y
3 screw (PTT2.6 × 8)
3 two screws (PTT2.6 × 8)
4 claw 6 flexible flat cable (CNP811) 3 screw (PTT2.6 × 8)
MECHANISM DECK (MG-164NZ-138)
3 two screws (PTT2.6 × 5) 4 bracket (MD)
5 mechanism deck (MG-164NZ-138)
1 screw (PTT2.6 × 5)
2 connector (CN101)
1 screw (PTT2.6 × 5)
9
SERVO BOARD
2 two screws (BVTT2 × 4) 2 two screws (BVTT2 × 4)
3 servo board
1 sensor flexible board (CN102) 1 flexible board (CN103)
MAIN BOARD
1 three ground point screws
2 three screws (PTT2.6 × 10)
3 main board
10
MD COVER ASS'Y
1 four screws (B2 × 3)
3 MD cover ass'y
shaft (MD cover guide)
cassette holder
A 2 Pushing the Cassette Holder in the direction of the arrow A with a screwdriver, etc., disengage the Shaft (MD Cover Guide) from the slot in the MD Cover Assy. Note: Take care not to scratch the optiocal Pick-up when pushing the Cassette Holder with a screwdriver. etc.
HEAT SINK
1 three screws (PTT2.6 × 10)
2 two screws (PTT2.6 × 12) 1 screw (PTT2.6 × 10) C6500R/C6500RX
3 heat sink
1 two screws (PTT2.6 × 10)
11
FLOAT BLOCK
3 Pushing an arrow A part, raise the float block up ward at the front to release a lock. A 1 tension spring (FLOAT B)
float block
lever (lock R) lever (lock L)
1 tension spring (FLOAT B) 2 two tension springs (FLOAT F)
LO MOTOR ASS'Y (LOADING) (M903)
4 Remove the bracket (LO) in the direction of the arrow A.
A 1 Remove solders of motor (M903)
5 LO motor ass'y (loading) (M903)
2 tension spring (rack)
3 claw
bracket (LO) bottom view
12
LEVER (LE) ASS'Y
2 stopper washer 2 lever (LE) ass'y
3 roller (GEAR E)
1
HOLDER ASS'Y
4 Remove the holder ass'y in the direction of the arrow.
2 type-E stopring 1.5
1 spring (CHKG)
2 type-E stopring 1.5
2 type-E stopring 1.5 3 lever (lock R)
3 lever (lock L) 1 spring (CHKG) 2 type-E stopring 1.5
13
CHUCKING ARM ASS'Y
1 Remove the chucking arm ass'y in the direction of the arrow.
holder ass'y
OPTICAL PICK-UP (KMS-241C/J1NP)
4 screw (B2 × 3) 6 bearing (SL) 5 feed screw ass'y 7 optical pick-up (KMS-241C/J1NP)
1 two screws (K2 × 3)
3 screw (K2 × 3)
2 guide shaft (OPT L)
14
SL MOTOR ASS'Y (SLED) (M902), SP MOTOR ASS'Y (SPINDLE) (M901)
4 screw (P1.7 × 1.8) 9 two screws (P1.7 × 1.8) 5 bracket (SL) 2 two screws (2 × 8) 6 SL motor ass'y (sled) (M902) 0 bracket (SP) 7 screw (B2 × 3) qa SP motor ass'y (spindle) (M901) 3 sensor board
8 base (SL)
1 Remove solders of motors (M901, M902)
15
SECTION 3 ELECTRICAL ADJUSTMENTS
TEST MODE This set have the test mode function. 1. Turn ON the regulated power supply. (The clock is displayed)
Note: Press the
[OFF]
button, if the clock is not displayed.
2. 3. 4. 5.
Push the preset [4] button. Push the preset [5] button. Press the preset [1] button for more than two seconds. Then the display indicates all lights, the test mode is set.
1. Push the [OFF] button.
MD SECTION
MD section adjustments are done automatically in this set.
TUNER SECTION
Tuner section adjustments are done automatically in this set.
16
MDX-C6400R/C6500R/C6500RX SECTION 4 DIAGRAMS
4-1. BLOCK DIAGRAM SERVO Section
100 EFMO 15 TX IC301 (1/2)
· SIGNAL PATH
ADDT 23
: MD PLAY
DIGITAL SIGNAL PROCESSOR, EFM/ACIRC ENCODER/DECODER, SHOCK PROOF MEMORY CONTROLLER, ATRAC ENCODER/DECODER, 2M BIT D-RAM IC301 (1/2)
SHOCK PROOF MEMORY CONTROLLER
EFM/ACIRC ENCODER/DECODER
ATRAC ENCODER/DECODER
FILI 59 PCO 58 CLTV 61 FILO 60
FILTER
PLL
SAMPLING RATE CONVERTER
48 47
MORFO MORFI
RF AMP, FOCUS/TRACKING ERROR AMP IC302 51 52 RFO 46 40 AGCI RF AGC & EQ EQ B.P.F. WBL AUX 33 RF 38 55 ASYO ASYI RFI COMPARATOR
DIGITAL AUDIO INTERFACE
DIN 21 DOUT 22 (Page 19) DADT 24
BCK LRCK FS256
I J
1 2
I J
DADT, BCK, LRCK, FS256
RF AMP
A
26 25 27
XBCK LRCK FS256
D-RAM PEAK BOTM 37 36
ADFG
F B
3T
TEMP PEAK & BOTTOM WBL
CLOCK GENERATOR
OSCI OSCO
16 17
512FS OSC IC304
X301 22.5792MHz
A E DETECTOR C D E F
XRST DQSY
8 9
E F
I-V AMP
TRACKING ERROR AMP COMMAND
SE
26 28
94 93 10 LASER DIODE ILCC PD LD PD AUTOMATIC POWER CONTROL Q302 APC 11
WBL 3T EQ
12
11
14
9 8
5 6 7
MNT0 MNT1 MNT2 MNT3
SPRD
SQSY
SENS SRDT
SPFD
XINT
TE
1 2 3 4 XOE XWE XRAS XCAS
LD/PD AMP
F0CNT
10
SWDT SCLK XLAT
PD
APCREF
12 2 4 6
V-I CONVERTER
SERIAL/ PARALLEL CONVERTER, DECODER
5
13 LEVEL SHIFT IC502
3 1
13 1 3 5
41 45 44 42
LEVEL SHIFT IC503 4 2
22 OE 3 WE 4 RAS 23 CAS
6
12
12 OPTICAL PICK-UP BLOCK (KMS-241C) FOCUS/TRACKING COIL DRIVE, SPINDLE/SLED MOTOR DRIVE IC303
20 +3.3V
16 17 18
FOK SHOCK XBUSY SLOCK
9 12, 14 18, 5 A0 A9
34
79
32 29, 34 38, 43
FOCUS ERROR AMP
FE
F0CNT
SPINDLE SERVO
SWDT SCLK XLAT
A00 A09
4 5 6 7
A B C D
B.P.F.
29
30
32
78
I-V AMP
ABCD AMP
ABCD
35 CPU INTERFACE MONITOR CONTROL
1, 2, 24, 25 D0 D3
D
A
AT AMP
ADFG
47, 46, 48, 49
I
C
B
J
ADFM
ADIN
ADIP DEMODULATOR/ DECODER
SUBCODE PROCESSOR
INTERNAL BUS
D0 D3
D-RAM IC307
(Page 19) PSB 16 PEAK HOLD Q301 SPFD SPRD +3.3V 13 RECP APCREF 83 M902 (SLED) SFDR 92 SRDR 91
PWM GENERATOR SWDT SCLK XLAT
RESET ABCD TH501
EMPHASIS
RESET, EMPHASIS
B
MNT0 MNT1 MNT2 MNT3
MD-RST
CC-XINT
MD-SO MD-CKO MD-LAT
DEEMP
SENS MD-SI
SQSY
TEMP
M901 (SPINDLE)
M
6 OUT4F 8 OUT4R
IN4R 3 IN4F 4
IC306
59 66 75 64 65 74 73 62 63
AUX1 AUX2 ABCD FE TE SE PEAK BOTM
62
55
54 52
45 51 64
26 27 28 29
39
66 LOCK 21 LOCK
C
(Page 19)
AUTOMATIC POWER CONTROL
31 EXTAL ANALOG MUX X501 10MHz
EJECT LOAD
LIMIT-IN
M
27 OUT2F 25 OUT2R
IN2F 29 IN2R 30
MD MECHANISM CONTROLLER IC501 (1/2)
A-MUTE 67
E-SW
MD-ATT
D
(Page 19)
A/D CONVERTER DIGITAL SERVO SIGNAL PROCESS
2-AXIS DEVICE
(TRACKING) (FOCUS)
7 FROM CPU INTERFACE XLRF CKRF DTRF 5 80 81 82 LOADING MOTOR DRIVE IC305 RIN
6
63
C-SW
32 XTAL
11
56
FCS+
21 OUT1F 23 OUT1R
IN1F 19 IN1R 18
FFDR 88 FRDR 89
4 FIN LOADING START/ EJECT END LOADING END ON: When completion of the disc loading. (LIMIT) ON: When the optical pick-up is inner position.
FCS TRK+ TRK 12 OUT3F 10 OUT3R IN3F 14 IN3R 15 TFDR 86 TRDR 85 DIGITAL SERVO SIGNAL PROCESSOR IC301 (2/2)
AUTO SEQUENCER
OUT1 OUT2 1 7 M903 (LOADING)
ON: When the disc loading start and the disc eject completion.
05
M
17
17
MDX-C6400R/C6500R/C6500RX
4-2.
BLOCK DIAGRAM TUNER Section
BU B+ TUNER +8.7V TUNER +5.6V FM/AM TUNER UNIT TU1
VDD E2P (5V)
VCC (8.5V)
VDD (5V)
J1 (FM/AM ANTENNA) 2 ANT-FM
11
5
16 MPX 10 MUTING Q111 MPX
E
(Page 19)
SDA (E2PROM) SCL (E2PROM)
S-METER
RDS-DET
FM-AGC
SDA (12CBUS) SCL (12CBUS)
1
ANT-AM
IF-AM
AM-DET
8 MUTING Q121 MUTING CONTROL SWITCH Q131
AM
F
(Page 19)
17 18
4
14
9
12 13
19
D131
IF-AM
G I
(Page 19)
DATA CLOCK
DATA, CLOCK
(Page 19)
RDS DECODER IC51
SIGNAL QUALITY DECODER RDS/RDBS DEMODULATOR & DECODER
5 4 INTERFACE REGISTER IIC BUS SLAVE TRANSCEIVER SDA 9 SCL 10 BUFFER Q1
SC 57 kHz OUT 18 16 BAND-PASS MPX FILTER
19
CIN
CLOCKED COMPARATOR
20
LVIN
OSCO
DAVN
MULTI PATH DETECTOR
MPTH
2
OSCILLATOR & CLOCK
DATA CLOCK
5
4
8
BAND-PASS FILTER IC90 Q90 NOISE DET DISCHARGE SWITCH
OSCI
X51 4.332MHz
S-METER
H
(Page 19)
9 10
51
53
52
64
50
32
56
FMAGC
DAVN
NS MASK
VSM
QUALITY
E2P SIO E2P CKO
MASTER CONTROLLER IC501 (1/3)
TUNATT
MPTH
· SIGNAL PATH : FM : MW/LW
05
18
18
MDX-C6400R/C6500R/C6500RX
4-3.
BLOCK DIAGRAM MAIN Section
CNJ151 (1/2) BUS AUDIO IN DADT, BCK, LRCK, FS256 (L) (R) R-CH INPUT SELECT, ELECTRICAL VOLUME, FM MPX IC151 CNJ151 (2/2)
D/A COMVERTER
DIGITAL FILTER
NOISE SHAPER
(Page 17)
A
INPUT INTERFACE
DADT BCK LRCK
5 6 4
DATA BCK LRCK
OUTPUT SELECTOR
VOUTL 12 VOUTR 9 R-CH
INPUT MULTIPLEXER
3 1 11
FD1L SEL AM
LOUDNESS/ VOLUME
SOFT MUTE
TONE CONTROL
MONO FADER
OUTLF MIXER OUTLR
30 29 MUTING Q171 R-CH MUTING Q271
(L) AUDIO OUT FRONT (R) (C6500R, C6500RX)
MUTE
LOUDNESS
FS256
1
XTI
CLK CONTROL
MODE CONTROL DIGITAL FILTER, D/A CONVERTER IC101
12
AMIF
AM/FM NOISE BLANKER DEMODULATOR +STEREO ADJUST +STEREO BLEND MUTING Q181 L.P.F. S&H HIGH-CUT R-CH R-CH MUTING Q281 D/A CONVERTER
(L)
AUDIO OUT REAR (C6500R, C6500RX)
DM1
DM0
(Page 17)
B
RESET, EMPHASIS
RESET
15
RSTB
13
MPX
L.P.F.
PILOT CANCELATION
17
16 PLL PILOT DET
(R)
AUDIO OUT (C6400R)
EMPHASIS
(Page 18) (Page 18) (Page 18)
F G E
AM IF-AM MPX
SDA SCL SM
DIGITAL CONTROL IIC BUS
POWER AMP IC611
CN601 (1/2) (POWER CONNECTOR) 1
LEVEL
FL+ 12 FL-IN D621 FL
5 9 3 4
FRONT L (+) FRONT L () FRONT R (+) 12 FRONT R () 2 REAR L (+) 10 REAR L () 3 REAR R (+) 11 REAR R ()
20
21
18
14
FR+ 21 14 FR-IN (Page 18)
I
DATA, CLOCK
DATA CLOCK 11 RL-IN
FR 23 RL+ RL 9 7
(Page 18)
H C
S-METER LOCK 15 RR-IN 84
LOCKIN
(Page 17)
RR+ 17 70
I2C SIO
71
I2C CKO
57
VOLATT
RR 19 BEEP 16 AMPATT 60
LCDSO LCDCKO TELATT LCDCE TEST IN
MASTER CONTROLLER IC501 (2/3)
16 AUX IN 22 MUTE 4 STNBY
KEYACK
RCIN0
REIN0
REIN1
DOORSW
NOSESW
AMPON 59
KEYIN0
KEYIN1
AD-ON
RCIN1
X1A
X0A
48 85
46
47
36
37
76
35
67
12
13 14 15
93
92
73
74
58
ATT
X1
X0
79
81 15 TEST
KEY ACTIVE SWITCH Q651, 652
U-COM +5V
14
CN500 MAIN BODY SIDE
X501 3.68MHz
X502 32.768kHz LEVEL SHIFT Q571 (C6500R, C6500RX) 13 TEL-ATT D571
SW504 (NOSE DETECT)
DI CL SE
J501 REMOTE IN LSW810, LSW901 917, S901 904
D501 ROTARY ENCODER RE901 VOLUME/BASS/TREBLE/ BALANCE/FADER CONTROL D653
1
CN901 FRONT PANEL SIDE
64 63 62 BACK-UP B+
D622
BATTERY OFF MUTE DRIVER Q621
OSC C953, R957
60 OSC
LIQUID CRYSTAL DISPLAY DRIVER IC901 S04 S51 4 51 COM1 COM4 52 55
D502
MUTING CONTROL SWITCH Q622
· SIGNAL PATH : MD PLAY : FM
LCD901 LIQUID CRYSTAL DISPLAY (Page 17) 05
D302
: MW/LW : BUS AUDIO IN
D
MD-ATT
19
19
MDX-C6400R/C6500R/C6500RX
4-4.
BLOCK DIAGRAM BUS CONTROL/POWER SUPPLY Section
CN701 BUS CONTROL IN (FOR SONY BUS) 3 SIRCS D708 SIRCS BUFFER Q704 RESET SIGNAL GENERATOR IC652
REMOTE CONTROL RECEIVER IC951
MASTER CONTROLLER IC501 (3/3) CN601 (2/2) (POWER CONNECTOR) D673 D674 AMP-R 86 HSTX 5 6 AMP+B 8 ANT+B D301 REGULATOR IC671 11 TU8.7V D2 VCC 7 10 TU5.6V BACK-UP B+ POWER AMP (IC611) B+ 6 ANT-R
24 SIRCS
BU B+
90 RSTX
SW503 RESET SONY BUS INTERFACE IC701 2 RESET 2 RST RESET SWITCH RST
TUNER +8.7V TUNER +5.6V RDS DECODER (IC51) B+ 9 8 11 18 UNISO 17 UNISI 19 UNICKO 20 UNICKI 3 BUSON U-COM +5V PW ON 120 TUNON 1 77 BUIN COM +8V (AUDIO CIRCUIT B+) D1
13
11 SYSRST
5 DATA 6
DATA
DATA IN DATA OUT
9 COM8V
CLK 6 BUS ON BUS ON SWITCH Q705
4
BU B+ D676 PULL UP +5V D677
5 BU+B STB
1
BUS ON BUS OUT BUS ON ON IN 12 SWITCH
5.6VON SW 3
CLK
4
7 BATT 3
BATT
BATTERY BU IN 10 SWITCH
TH701
D702 D701 LED901-904, LED910-915, LSW901-917 ILLON 7 REGULATOR CONTROL SWITCH Q633
LCD B+ LCD DRIVER (IC901) B+ REGULATOR Q631 FU601 16 +B
BACK-UP B+
BATTERY DETECT Q701
8.7VON SW 2 D662
4
CLK IN
ACC IN 82
ACCESSORY CHECK Q661
7 ACC
DOORIND 29
LED810 (MD DISC SLOT) LSW810 Z
LED810, LSW810
REGULATOR Q551
MD MECHANISM CONTROLLER IC501 (2/2)
LO- +12V LOADING MOTOR DRIVER (IC305) B+ B+ SWITCH Q402, 403
+12V REGULATOR Q361
60 BU-IN 61 BUS-ON 30 RESET 49 UNISI 48 UNICKIO LEVEL SHIFT Q706 50 UNISO
MD-ON 65 MDMON 10 REGULATOR CONTROL SWITCH Q363 VCC
DRIVER +5V MOTOR/COIL DRIVER (IC303) B+ +5V REGULATOR Q362
+3.3V 46 LINKOFF REGULATOR CONTROL SWITCH Q250
+3.3V REGULATOR IC401, Q401
05
20
20
MDX-C6400R/C6500R/C6500RX
· Circuit Boards Location
4-5.
NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
Note on Schematic Diagram: · All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics and tantalums. · All resistors are in and 1/4 W or less unless otherwise specified. · % : indicates tolerance. f · : internal component. · C : panel designation. Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. · U : B+ Line. · Power voltage is dc 14.4V and fed with regulated dc power supply from ACC and BATT cords. · Voltages are taken with a VOM (Input impedance 10 M). Voltage variations may be noted due to normal production tolerances. · Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production tolerances. · Circled numbers refer to waveforms. · Signal path. E : MD PLAY F : FM f : MW/LW L : BUS AUDIO IN
SENSOR board
SERVO board SUB board
Note on Printed Wiring Board: · X : parts extracted from the component side. · Y : parts extracted from the conductor side. z · : Through hole. f : internal component. · · b : Pattern from the side which enables seeing. (The other layers' patterns are not indicated.) Caution: Pattern face side: (Conductor Side) Parts face side: (Component Side)
Parts on the pattern face side seen from the pattern face are indicated. Parts on the parts face side seen from the parts face are indicated.
KEY board
MAIN board
21
21
MDX-C6400R/C6500R/C6500RX
4-6. PRINTED WIRING BOARDS SERVO Board (Component Side)/SENSOR Board · See page 21 for Circuit Boards Location.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
A
(LOADING END) C103 C105
R404 R405
SERVO BOARD
M903 (LOADING) RED
(COMPONENT SIDE)
L101
5 IC401
E C
C402
4 K A D401
C352 C11
20
11
C109
+
B
8
C403 R406
1
M
B
C306 BLK R319 (CHASSIS) C305 C304
R317
C108
Q401
1 IC305
8
IC101
L102 R316
29 1 10
+ C106 C104
R102
30 4 5
FB301 R318 11 R320 C308
R312
R311
C
C107
50 51
26 CN103 25
FB302
(CHASSIS)
11
C341
8
R325 1 R324
5 IC304
8
7
R354
D
C310
CN101
X301
C340
R328 C311
R327
IC301
1
4
IC502
SENSOR BOARD
(COMPONENT SIDE)
C314
R308
14
R307
1
D501 K A
R538
SENSOR FLEXIBLE BOARD
1
RED M902 (SLED)
1-654-693-
11
75
1
R306
E
M
76
BLK
R331
100
R305
8
R304 R303
7
M
M902 (SPINDLE) E C B R329
A
IC503 1 2
R517
Q301
R330
MAIN BOARD CN301
5
4
R351
R302 R353 C343 R352 C342 R301
F
SENSOR BOARD
(CONDUCTOR SIDE)
C315
C348
RED
BLK
11
1-676-656-
IC306 1 3
14
1
(Page 27)
(11)
C338
R525
R524
R523
R530
R522
R537
R536
L304
L303
C337
R518
C339
G
(LIMIT)
32
17
80
C349
65
1 IC303
R501
64
H
1
16
C336
R502 R503
L306
C335
L305
R531
IC501
C334
C516
· Semiconductor Location
R535 R539 + C318 1
R356
R505
D401 D501 IC101 IC301 IC302 IC303 IC304 IC305 IC306 IC401 IC501 IC502 IC503 Q301 Q302 Q401
A-15 E-13 B-11 D-8 K-11 H-8 D-10 B-16 F-8 A-14 H-15 D-11 F-11 E-6 K-10 B-13
05 LOADING START EJECT END (CHASSIS) OPTICAL PICK-UP BLOCK (KMS-241C)
R355
R504
I
R516
Ref. No.
Location
24
C501
41
C331
C328
+ C319 48 1
C329 37 36
C330
25
40
J
CN102
C327
X501 R511
C326
L302
R532
IC302
R346
20
R337 C320
C325 12 13 C321
R348 R341 C322
25 24
R347
R527 R528 +
C346
C324
K
C347
R506 (CHASSIS)
R336
R350
R340
R345 R344 R343 R342 R338
R526 R529
R349
R357
R339
C E
11
1-675-655-
11
1-676-656-
(11)
22
22
B
Q302
(11)
MDX-C6400R/C6500R/C6500RX
4-7. PRINTED WIRING BOARD SERVO Board (Conductor Side)
1 2 3 4 5
· See page 21 for Circuit Boards Location.
6 7 8 9 10 11 12
A
SERVO BOARD
(CONDUCTOR SIDE)
+
R101
C101
R403
R104
B
C510
C202
C
R201
C201
Q402
E
B B C E R202
C102
R401
R402
Q403
+ C361
C362
+
13
9
5
1
C
IC307
C359
C307
R359
L301
C344
14
18
22
26
C353
C302
D
+
C345
C358 C301 C356 C511 C357
E
L501
R332
R334
R333
R335
C506
+
C317
F
C505
C512 RB302 RB301
C309
C316
+ R534 R533 C504
C351
C515
G
C514 C513
C350
R542
R520
R540
H
R521
C333 R519
I
C503
R512
TH501
J
R510
RB503
K
11
05
· Semiconductor Location
Ref. No. IC307 Q402 Q403 Location C-10 B-4 B-5
1-675-655-
(11)
23
23
MDX-C6400R/C6500R/C6500RX
4-8. SCHEMATIC DIAGRAM SERVO Board (1/2) · See page 31 for Waveforms. · See page 36 for IC Block Diagrams.
· Voltages and waveforms are dc with respect to ground under no-signal conditions. no mark : MD PLAY : Impossible to measure
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
24
24
MDX-C6400R/C6500R/C6500RX
4-9. SCHEMATIC DIAGRAM SERVO Board (2/2) · See page 31 for Waveforms. · See page 36 for IC Block Diagram.
(Page 29)
· Voltages and waveforms are dc with respect to ground under no-signal conditions. no mark : MD PLAY : Impossible to measure
25
25
MDX-C6400R/C6500R/C6500RX
4-10. PRINTED WIRING BOARD MAIN Board (Component Side) · See page 21 for Circuit Boards Location.
· Semiconductor Location
Ref. No. D1 D301 D501 D502 D551 D552 D553 D554 D555 D556 D557 D558 D559 D560 D571 D603 D605 D611 D612 D613 D614 D615 D616 D617 D618 D622 D623 D624 D653 D661 D662 D673 D674 D701 D702 D703 D704 D705 D706 D708 D710 IC51 IC90 IC151 IC501 IC652 IC701 Q1 Q111 Q131 Q171 Q181 Q250 Q271 Q281 Q363 Q551 Q571 Q621 Q622 Q633 Q651 Q652 Q661 Q701 Q704 Q705 Q706 Location E-9 G-5 I-7 H-7 J-13 K-13 K-13 J-12 K-13 J-12 K-13 J-12 K-13 J-12 B-5 B-4 B-5 B-7 B-7 C-7 C-7 C-7 C-7 C-6 C-6 D-9 C-9 C-9 I-7 D-5 D-5 C-5 C-5 E-5 C-4 B-3 B-2 B-2 B-2 G-7 D-4 I-12 G-11 D-10 I-5 J-3 C-3 G-11 E-12 F-12 B-11 B-11 H-2 C-11 C-11 I-3 J-6 D-5 C-10 C-9 J-2 I-8 I-8 D-5 D-5 G-7 C-4 D-4
26
26
BATT
BATT
GND
RR
RL
RL
RL
FR
FR
FL
FL
ATT
4-11.
PRINTED WIRING BOARD MAIN Board (Conductor Side)
· See page 21 for Circuit Boards Location.
6 8 3
5 7 2
4
MDX-C6400R/C6500R/C6500RX
9 1
RR+ FR+ RL+ FL+ FL+
10 2
RL+
11 3
RR+
12 4
AMP REM FR+
13 5
14 6
ANT REM
15 7
ACC
16 8
ANT REM GND ACC
1
(FRONT VIEW)
· Semiconductor Location
Ref. No. D2 D90 D91 D92 D131 D302 D361 D362 D561 D562 D563 D564 D601 D602 D604 D621 D631 D671 D672 D675 D676 D677 D709 IC611 IC671 Q90 Q121 Q361 Q362 Q631 Location E-7 H-11 H-11 G-11 F-12 G-7 I-2 G-2 K-11 K-11 K-13 K-12 C-3 B-4 A-5 B-10 J-2 C-5 C-5 I-4 I-4 I-4 G-5 A-7 F-1 G-11 E-12 H-1 G-1 J-2
(Page 32)
(Page 22)
27
27
MDX-C6400R/C6500R/C6500RX
4-12. SCHEMATIC DIAGRAM MAIN Board (1/3) · See page 31 for Waveform. · See page 36 for IC Block Diagrams.
(Page 30)
(Page 29) · Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions. no mark : FM ( ) : MW [ ] : LW
28
28
MDX-C6400R/C6500R/C6500RX
4-13. SCHEMATIC DIAGRAM MAIN Board (2/3) · See page 31 for Waveforms.
(Page 28)
(Page 25)
(Page 30)
29
29
· Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions. no mark : FM ( ) : MW [ ] : LW : MD PLAY : Impossible to measure
MDX-C6400R/C6500R/C6500RX
4-14. SCHEMATIC DIAGRAM MAIN Board (3/3) · See page 36 for IC Block Diagrams.
(Page 28)
(Page 33)
(Page 29)
· Voltages are dc with respect to ground under no-signal (detuned) conditions. no mark : FM : MD PLAY
30
30
MDX-C6400R/C6500R/C6500RX
· Waveforms SERVO Board
1 IC101 1 (XTI) (MD Play Mode) 6 IC301 wh (XBCK) (MD Play Mode) qa IC302 1, 2, r;, rh (I, J, AGCI, RFO) (MD Play Mode)
MAIN Board
1 IC51 4 (OSCD)
KEY Board
1 IC901 y; (OSC)
4.4 Vp-p
4.6 Vp-p
Apporx. 0.6 Vp-p
5 Vp-p
2.6 Vp-p
88 ns
354 ns 7 IC301 wj (FS256) (MD Play Mode) qs IC304 1, 2 (MD Play Mode)
231 ns 2 IC501 ud (X1A)
26.4 µs
2 IC101 4 (LRCK) (MD Play Mode)
3.8 Vp-p
4.4 Vp-p
4.1 Vp-p
5.4 Vp-p
22.7 µs
3 IC101 6 (BCK) (MD Play Mode)
88 ns
44.3 ns qd IC304 3 (MD Play Mode)
30.5 µs
3 IC501 od (X1A)
8 IC301 tg (RFI), IC302 ek (RF) (MD Play Mode)
3.4 Vp-p
Apporx. 1.5 Vp-p
3.4 Vp-p
5.6 Vp-p
354 ns 4 IC301 qh (OSCI) (MD Play Mode) 9 IC301 yg (FE), IC302 ef (FE) (MD Play Mode)
44.3 ns
272 ns
qf IC304 7 (MD Play Mode)
4.6 Vp-p
Approx. 0.5 Vp-p
4.4 Vp-p
44.3 ns 5 IC301 wg (LRCK) (MD Play Mode) 0 IC301 uf (TE), IC302 wh (TE) (MD Play Mode)
44.3 ns
qg IC501 ea (EXTAL)
4.4 Vp-p
3.7 Vp-p
Approx. 2 Vp-p
22.7 µs
101 ns
31
31
MDX-C6400R/C6500R/C6500RX
4-15. PRINTED WIRING BOARD SUB Board · See page 21 for Circuit Boards Location.
(Page 27)
(Page 34)
32
32
4-16.
SCHEMATIC DIAGRAM SUB Board
MDX-C6400R/C6500R/C6500RX
(Page 30)
(Page 35)
33
33
MDX-C6400R/C6500R/C6500RX
4-17. PRINTED WIRING BOARD KEY Board · See page 21 for Circuit Boards Location.
· Semiconductor Location
Ref. No. IC951 LED901 LED902 LED903 LED904 LED910 LED911 LED912 LED913 LED914 LED915 Location C-5 A-2 C-2 C-3 A-3 B-12 B-12 A-12 A-5 B-5 B-5
· Semiconductor Location
Ref. No. D901 D902 D903 D904 D951 D952 IC901 Location A-11 B-10 B-10 B-10 C-4 B-6 B-8
(Page 32)
34
34
4-18.
SCHEMATIC DIAGRAM KEY Board
· See page 31 for Waveform.
MDX-C6400R/C6500R/C6500RX
(Page 33)
· Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions. no mark : FM
35
35
MDX-C6400R/C6500R/C6500RX
· IC Block Diagrams SERVO Board IC101 PCM1718E/2K
IC302
CXA2523AR
COMPO COMPP MORFO RF AGC MORFI ADDC PEAK AGCI OPN OPO RFO
48
XTI 1 DGND 2 VDD 3 LRCIN 4 DIN 5 NOISE SHAPER BCKIN 6 ZERO 7 D/C_R 8 VOUTR 9 AGND 10 5 LEVEL DAC LOWPASS FILTER CMOS AMP 5 LEVEL DAC LOWPASS FILTER CMOS AMP 15 RSTB 14 FORMAT 13 D/C_L 12 VOUTL 11 VCC CLK CONTROL INPUT INTERFACE DIGITAL FILTER 20 XTO 19 CLKO MODE CONTROL 18 MUTE
47
46
45 + USROP
44
43 42 + BPF3T
41
40 RF AGC
39
38 EQ
RF
37
+
RFA1
USRC DET EQ AUX SW
RFA2
17 DM1 16 DM0
RFA3 HLPT 1 2 3T
I J
1 2
1 2 OFST 1 2
PEAK3T P-P WBL PEAK
PTGR 2 GRV 1 PBSW
3T
TEMP 36 BOTM
VC
3
A
4 IVR
B
5 IVR
IC301
CXD2652AR
APCREF F0CNT TEST3 TEST2 TEST1 SRDR DVDD DCHG SPRD EFMO TRDR LDDR DVSS FRDR SFDR ADFG SPFD CKRF TFDR DTRF XLRF FFDR FGIN APC FS4
C
6 IVR
100 99 98 97 96 95
94 93
92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76
AUTO SEQUENCER
MNT0 1 MNT1 2 MNT2 3 MNT3 4 MONITOR CONTROL EACH BLOCK
SPINDLE SERVO
PWM GENERATOR
75 AUX2 74 TE 73 SE 72 AVSS 71 ADRB
D
7 IVR
E
8 IVR
ADIP DECODER SWDT 5 SCLK 6 XLAT 7 SRDT 8 SENS 9 XRST 10 SQSY 11 DQSY 12 RECP 13
PLL
70 ADRT 69 AVDD 68 ADIO
CPU I/F
EACH BLOCK
67 VC SERVO DSP A/D CONVERTER ANALOG MUX 66 AUX1 65 FE 64 ABCD 63 BOTM
F
9 IVR
GSW PD 10
SUBCODE PROCESSOR
62 PEAK
AUXSW + + APC 11 APCREF 12 13
GND
61 CLTV 60 FILO 59 FILI 58 PCO 57 PDO
XINT 14 TX 15 OSCI 16 OSCO 17 XTSL 18 NC 19 DVSS 20 DIN 21 DOUT 22 CLOCK GENERATOR EACH BLOCK
SHOCK RESISTANT MEMORY CONTROLLER
EFM/ACIRC ENCODER/ DECODER
XSTBY
SCLK
SWDT
XLAT
EQADJ
VREF
TEMPI
TEMPR
F0CNT
DIGITAL AUDIO I/F
SAMPLING RATE CONVERTER
COMP
55 RFI 54 BIAS 53 AVDD 52 ASYI 51 ASYO
ADDT 23 DADT 24 LRCK 25
ATRAC ENCODER/DECODER
ADDRESS/DATA BUS A00 - A11, D0 - D3
26 27 28
DVDD XBCK FS256
29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49
DVSS XRAS XCAS XWE XOE A03 A02 A01 A00 A10 A04 A05 A06 A07 A08 A11 A09 D1 D0 D2 D3
50
MVCI
36
36
3TADJ
VCC
56 AVSS
+ + + + + + + IV
CVB
BOTTOM WBL
PBH
GRVA
35 ABCD 34 FE 33 AUX BPFC 32 ADFG 31 ADAGC
AA
ABCDA
BB
+ +
30 ADIN FEA
CC BPF22 + + DD WBL + + EFB EBAL ESW FF + FBAL TESW PTGR WBL ATA ADIP AGC
DET
29 ADFM
1 2 SEA
TG
28 SE 27 CSLED
EE
+
EE'
1 2 TEA
TG
26 TE
FF'
WBL 3T EQ VI CONV 25 WBLADJ
COMMAND
BGR VREF
SCRI - PARA DECODE
14
15
16
17
18
19
20
21
22 23
24
IC303
CAPA
BH6511FS-E2
PGND2 PGND1 OUT2R OUT1R CAPA+ OUT2F OUT1F VM12 IN2R IN1R VM2 VM1 IN2F IN1F VDD
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
INTERFACE
AMP
AMP
AMP
AMP
INTERFACE
VDD
CHARGE PUMP. OSC
PREDRIVE
PREDRIVE
PREDRIVE
PREDRIVE
INTERFACE
AMP
AMP
AMP
AMP
INTERFACE
PSB
1
GND
2
VG
3
IN4R
4
IN4F
5
VM4
6
OUT4F
7
PGND4
8
OUT4R
9
VM34
10
OUT3R
11
PGND3
12
OUT3F
13
VM3
14
IN3F
15
IN3R
16
PSB
IC305
BA6287F
OUT1 1
8 GND
VM 2
7 OUT2
DRIVER TSD
DRIVER
VCC 3
CONTROL LOGIC
6 VREF
POWER SAVE FIN 4 5 RIN
IC307
MN41V4400TT-08S
TIMING GENERATOR
TIMING GENERATOR
26 VSS
DQ1 DQ2 WE RAS A9 NC NC NC
1 2 3 4 5
25 DQ4 24 DQ3 WRITE CLOCK GENERATOR 23 CAS 22 OE 21 NC 20 NC 19 NC 18 17 16 15 14 A8 A7 A6 A5 A4
ADDRESS BUFFERS
COLUMN
6 7 8
COLUMN DECODERS
I/O SELECTOR
ROW
A0 9 A1 10 A2 11 A3 12
INTERNAL ADDRESS COUNTER
REFRESH CONTROL CLOCK
SENSE AMPLIFIERS INPUT BUFFERS MEMORY CELLS OUTPUT BUFFERS
ROW DECODERS
WORD DRIVERS
DATA BUS
VCC 13
37
MAIN Board IC51 SAA6588T/V2-118
SCOUT VSSA MAD PSWN
12 11 PAUSE DETECTOR
11
LVIN
VDDA
VREF
20
19
18
17
MPX
CIN
16
15
14
MULTI PATH DETECTOR
POWER SUPPLY & RESET 57kHz 8th ORDER BAND-PASS FILTER SIGNAL QUALITY DECODER 4 CLOCK 5 4 CLOCK INTERFACE REGISTER DATA DATA
CLOCKED COMPARATOR
RDS/RDBS DEMODULATOR
RDS/RDBS DECODER
TEST CONTROL
OSCILLATOR & CLOCK
IIC BUS SLAVE TRANSCEIVER
1 2
3
4
5
6
7
8
9
OSCI
DAVN
VSSD
SDA
+ +
OSCO
MRO MPTH
IC671
BA4908-V3
REGULATOR
OVER VOLTAGE PROTECT + +
VDDD
TCON
1
2 3 4
5
6
7
8
9
10
SCL
AFIN
13 10
12
TUNER8.7 ANT SW TUNER5.6 SW STB
VDD5.6V
COM8.7V
TUNER5.6V
TUNER8.7V
38
AMP
GND
NC
VCC
ANT
IC151
TDA7402TR
OUTSWR OUTSWL OUTSSL OUTSSR
24 23
ACINLR ACINRF ACINRR
33 32 31
30
29 MIXER
28
27
OUTRR
OUTLR
OUTRF
OUTLF
26
25
MONO- MONOFADER FADER ACINLF 34 SWINR 35 SWINL 36 ACOUTR 37 ACOUTL 38 CREF 39 FRONT ACIN OUTPUT SELECTOR MAIN SECOND REAR SW
MONO- MONOFADER FADER
MONO- MONOFADER FADER
SUBWOOFER +PHASE CONTROL
VOICE BANDPASS HP
IIC-BUS
LP
22 VDD 21 SCL 20 SDA
BASS SUPPLY TREBLE HIGH-CUT 19 GND 18 SM PULSE FORMER QUAL 17 QUAL
VOLUME
DIGITAL CONTROL
S&H
SOFTMUTE COMPANDER LOUDNESS LOUDNESS
25kHz LP
MUX 40
+
IN-GAIN +AUTO ZERO
IN-GAIN BEEP MUTE
DEMODULATOR +STEREO ADJUST +STEREO BLAND
MULTIPATH DETECTOR
16 MPOUT 15 MPIN
PILOT CANCELATION PIL DET
D/A CONVERTER
14 LEVEL
MAIN SOURCE SELECTOR MD1 41 MD1G 42 MD2 43 MD2G 44 MAIN
MIXING SELECTOR
SECOND SOURCE SELECTOR PLL 80kHz LP
INPUT MULTIPLEXER PHONO MAIN 1 2 CH0 3 4 5 6 AUX 7 8 9 10
13 MPX
FM AM 11 AM/FM NOISE BLANKER
12 AMIF
FD1L+ FD1L FD1R+ FD1R
FD2L+ FD2L FD2R+ FD2R
IC701
BA8270F-E2
SEL SER
BUS ON 1
BUS ON SWITCH RESET SWITCH BATTERY SWITCH
14 VCC
RST 2
BATT 3
13 12 11 10
RST BUS ON CLK IN BU IN
CLK 4 VREF 5 DATA 6 GND 7
9 DATA IN 8 DATA OUT
AM
39
4-19.
IC PIN FUNCTION DESCRIPTION
· SERVO BOARD IC301 CXD2652AR (DIGITAL SIGNAL PROCESSOR, DIGITAL SERVO PROCESSOR, EFM/ACIRC ENCODER/DECODER, SHOCK PROOF MEMORY CONTROLLER, ATRAC ENCODER/DECODER, 2M BIT D-RAM) Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 to 32 33 34 to 38 39 40 41 42 43 44 45 Pin Name MNT0 MNT1 MNT2 MNT3 SWDT SCLK XLAT SRDT SENS XRST SQSY DQSY RECP XINT TX OSCI OSCO XTSL RVDD RVSS DIN DOUT ADDT DADT LRCK XBCK FS256 DVDD A03 to A00 A10 A04 to A08 A11 DVSS XOE XCAS A09 XRAS XWE I/O O O O O I I I O (3) O (3) I O O I O I I O I -- -- I O I O O O O -- O O O O -- O O O O O Description Focus OK signal output to the MD mechanism controller (IC501) "H" is output when focus is on ("L": NG) Track jump detection signal output to the MD mechanism controller (IC501) Busy monitor signal output to the MD mechanism controller (IC501) Spindle servo lock status monitor signal output to the MD mechanism controller (IC501) Writing serial data signal input from the MD mechanism controller (IC501) Serial data transfer clock signal input from the MD mechanism controller (IC501) Serial data latch pulse signal input from the MD mechanism controller (IC501) Reading serial data signal output to the MD mechanism controller (IC501) Internal status (SENSE) output to the MD mechanism controller (IC501) Reset signal input from the MD mechanism controller (IC501) "L": reset Subcode Q sync (SCOR) output to the MD mechanism controller (IC501) "L" is output every 13.3 msec Almost all, "H" is output Digital In U-bit CD format subcode Q sync (SCOR) output terminal "L" is output every 13.3 msec Almost all, "H" is output Not used (open) Laser power selection signal input terminal "L": playback mode, "H": recording mode (fixed at "L" in this set) Interrupt status output to the MD mechanism controller (IC501) Recording data output enable signal input terminal Writing data transmission timing input (Also serves as the magnetic head on/off output) Not used (fixed at "L") System clock signal (512Fs=22.5792 MHz) input from the oscillator circuit System clock signal (512Fs=22.5792 MHz) output terminal Not used (open) Input terminal for the system clock frequency setting "L": 45.1584 MHz, "H": 22.5792 MHz (fixed at "H" in this set) Power supply terminal (+3.3V) (digital system) Ground terminal (digital system) Digital audio signal input terminal when recording mode Not used (fixed at "L") Digital audio signal output terminal when playback mode Not used (open) Recording data input terminal Not used (fixed at "L") Playback data output to the PCM1718E (IC101) L/R sampling clock signal (44.1 kHz) output to the PCM1718E (IC101) Bit clock signal (2.8224 MHz) output to the PCM1718E (IC101) Clock signal (11.2896 MHz) output to the PCM1718E (IC101) Power supply terminal (+3.3V) (digital system) Address signal output to the D-RAM (IC307) Address signal output to the external D-RAM Not used (open) Address signal output to the D-RAM (IC307) Address signal output to the external D-RAM Not used (open) Ground terminal (digital system) Output enable signal output to the D-RAM (IC307) "L" active Column address strobe signal output to the D-RAM (IC307) "L" active Address signal output to the D-RAM (IC307) Row address strobe signal output to the D-RAM (IC307) "L" active Write enable signal output to the D-RAM (IC307) "L" active
40
Pin No. 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88
Pin Name D1 D0 D2 D3 MVCI ASYO ASYI AVDD BIAS RFI AVSS PDO PCO FILI FILO CLTV PEAK BOTM ABCD FE AUX1 VC ADIO AVDD ADRT ADRB AVSS SE TE AUX2 DCHG APC ADFG F0CNT XLRF CKRF DTRF APCREF LDDR TRDR TFDR DVDD FFDR
I/O I/O I/O I/O I/O I O I (A) -- I (A) I (A) -- O (3) O (3) I (A) I (A) I (A) I (A) I (A) I (A) I (A) I (A) -- I (A) I (A) -- I (A) I (A) I (A) I (A) I (A) I O O O O O O O O -- O
Description
Two-way data bus with the D-RAM (IC307)
Digital in PLL oscillation input from the external VCO Not used (fixed at "L") Playback EFM full-swing output terminal Playback EFM asymmetry comparator voltage input terminal Power supply terminal (+3.3V) (analog system) Playback EFM asymmetry circuit constant current input terminal Playback EFM RF signal input from the CXA2523AR (IC302) Ground terminal (analog system) Phase comparison output for clock playback analog PLL of the playback EFM Not used (open) Phase comparison output for master clock of the recording/playback EFM master PLL Filter input for master clock of the recording/playback master PLL Internal VCO control voltage input of the recording/playback master PLL Light amount signal (RF/ABCD) peak hold input from the CXA2523AR (IC302) Light amount signal (RF/ABCD) bottom hold input from the CXA2523AR (IC302) Light amount signal (ABCD) input from the CXA2523AR (IC302) Focus error signal input from the CXA2523AR (IC302) Auxiliary signal (I3 signal/temperature signal) input terminal Not used (fixed at "H") Middle point voltage (+1.65V) input from the CXA2523AR (IC302) Power supply terminal (+3.3V) (analog system) A/D converter operational range upper limit voltage input terminal (fixed at "H" in this set) A/D converter operational range lower limit voltage input terminal (fixed at "L" in this set) Ground terminal (analog system) Sled error signal input from the CXA2523AR (IC302) Tracking error signal input from the CXA2523AR (IC302) Auxiliary signal input terminal Light amount signal input from the CXA2523AR (IC302) Connected to the +3.3V power supply Error signal input for the laser automatic power control Not used (fixed at "L") ADIP duplex FM signal (22.05 kHz ± 1 kHz) input from the CXA2523AR (IC302) Filter f0 control signal output terminal Not used (open) Serial data latch pulse signal output terminal Not used (open) Serial data transfer clock signal output terminal Not used (open) Writing serial data output terminal Not used (open) Control signal output to the reference voltage generator circuit for the laser automatic power control PWM signal output for the laser automatic power control Not used (open) Tracking servo drive PWM signal () output to the BH6511FS (IC303) Tracking servo drive PWM signal (+) output to the BH6511FS (IC303) Power supply terminal (+3.3V) (digital system) Focus servo drive PWM signal (+) output to the BH6511FS (IC303)
O (A) Filter output for master clock of the recording/playback master PLL
O (A) Monitor output of the A/D converter input signal Not used (open)
41
Pin No. 89 90 91 92 93 94 95 96 97 98 99 100
Pin Name FRDR FS4 SRDR SFDR SPRD SPFD FGIN TEST1 TEST2 TEST3 DVSS EFMO
I/O O O O O O O I I I I -- O Ground terminal (digital system) Input terminal for the test (fixed at "L")
Description Focus servo drive PWM signal () output to the BH6511FS (IC303) Clock signal (176.4 kHz) output terminal (X'tal system) Not used (open) Sled servo drive PWM signal () output to the BH6511FS (IC303) Sled servo drive PWM signal (+) output to the BH6511FS (IC303) Spindle servo drive PWM signal () output to the BH6511FS (IC303) Spindle servo drive PWM signal (+) output to the BH6511FS (IC303) Not used (fixed at "L")
EFM signal output terminal when recording mode
Not used (open)
* I (A) for analog input, O (3) for 3-state output, and O (A) for analog output in the column I/O.
42
· SERVO BOARD IC302 CXA2523AR (RF AMP, FOCUS/TRACKING ERROR AMP) Pin No. 1 2 3 4 to 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 Pin Name I J VC A to F PD APC APCREF GND TEMPI TEMPR SWDT SCLK XLAT XSTBY F0CNT VREF EQADJ 3TADJ VCC WBLADJ TE CSLED SE ADFM ADIN ADAGC ADFG AUX FE ABCD BOTM PEAK RF RFAGC AGCI COMPO COMPP ADDC OPO OPN RFO MORFI MORFO I/O I I O I I O I -- I O I I I I I O I I -- I O I O O I I O O O O O O O I I O I I O I O I O Description I-V converted RF signal I input from the optical pick-up block detector I-V converted RF signal J input from the optical pick-up block detector Middle point voltage (+1.65V) generation output terminal Signal input from the optical pick-up detector Light amount monitor input from the optical pick-up block laser diode Laser amplifier output terminal to the automatic power control circuit Reference voltage input terminal for setting laser power Ground terminal Connected to the temperature sensor Not used (open) Output terminal for a temperature sensor reference voltage Not used (open) Writing serial data input from the MD mechanism controller (IC501) Serial data transfer clock signal input from the MD mechanism controller (IC501) Serial data latch pulse signal input from the MD mechanism controller (IC501) Standby signal input terminal "L": standby (fixed at "H" in this set) Center frequency control voltage input terminal of internal circuit (BPF22, BPF3T, EQ) input terminal Reference voltage output terminal Not used (open) Center frequency setting terminal for the internal circuit (EQ) Center frequency setting terminal for the internal circuit (BPF3T) Power supply terminal (+3.3V) Center frequency setting terminal for the internal circuit (BPF22) Tracking error signal output to the CXD2652AR (IC301) Connected to the external capacitor for low-pass filter of the sled error signal Sled error signal output to the CXD2652AR (IC301) FM signal output of the ADIP Receives a ADIP FM signal in AC coupling Connected to the external capacitor for ADIP AGC ADIP duplex signal (22.05 kHz ± 1 kHz) output to the CXD2652AR (IC301) Auxiliary signal (I3 signal/temperature signal) output terminal Not used (open) Focus error signal output to the CXD2652AR (IC301) Light amount signal (ABCD) output to the CXD2652AR (IC301) Light amount signal (RF/ABCD) bottom hold output to the CXD2652AR (IC301) Light amount signal (RF/ABCD) peak hold output to the CXD2652AR (IC301) Playback EFM RF signal output to the CXD2652AR (IC301) Connected to the external capacitor for RF auto gain control circuit Receives a RF signal in AC coupling User comparator output terminal Not used (open) User comparator input terminal Not used (fixed at "L") Connected to the external capacitor for cutting the low band of the ADIP amplifier User operational amplifier output terminal Not used (open) User operational amplifier inversion input terminal Not used (fixed at "L") RF signal output terminal Receives a MO RF signal in AC coupling MO RF signal output terminal
43
· SERVO BOARD IC501 CXP84340-217Q (MD MECHANISM CONTROLLER) Pin No. 1 to 5 6 7 8, 9 10 11 12 13 14 to 17 18 19 20 21 22 23 24, 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 Pin Name TIN3 to TIN7 LOAD EJECT NCO MDMON E-SW AG-OK ADJ-OK NCO DFCTSEL DPLLSEL EMPHSEL LOCK NCO 2M/4M NCO MNT0 MNT1 MNT2 MNT3 RESET EXTAL XTAL VSS TX TEX AVSS AVREF INIT TEMP ACNT DO-SEL EE-CS EE-CKO EE-SIO MD-SO LINKOFF I/O I/O O O O O I O O O I I I O O I O I I I I I O I -- O I -- I I I I I O O I/O O O Description Input of the 4×8 matrix test keys ("L" is always output, except in test mode) Not used (open) Loading motor control signal output to the motor driver (IC305) "H" active *1 Loading motor control signal output to the motor driver (IC305) "H" active *1 Not used (open) Power supply on/off control signal output of the MD mechanism deck section main power supply and loading motor drive (IC305) power supply "H": power on Inputs the disc loading completion detect switch detection signal "L": When completed of the disc loading operation Output of aging status in test mode "L": under aging, "H": aging completed Not used (open) Output of status when aging completed in test mode "L": aging NG, "H": aging OK Not used (open) Not used (open) Select whether defect function is used for the CXD2652AR (IC301) "L": used this function , "H": not used this function (fixed at "H" in this set) Select whether digital PLL function is used for the CXD2652AR (IC301) "L": used this function , "H": not used this function (fixed at "H" in this set) Select whether emphasis signal output from pin or unilink data "L": outputs from both pin and unilink data, "H": output from pin only (fixed at "H" in this set) Mini-disc lock detection signal output to the master controller (IC501) "H": lock Not used (open) Select whether D-RAM capacitance 2M bit or 4M bit "L": 4M bit (external D-RAM) , "H": 2M bit (internal D-RAM of CXD2652AR) (fixed at "L" in this set) Not used (open) Focus OK signal input from the CXD2652AR (IC301) "H" is input when focus is on ("L": NG) Track jump detection signal input from the CXD2652AR (IC301) Busy monitor signal input from the CXD2652AR (IC301) Spindle servo lock status monitor signal input from the CXD2652AR (IC301) System reset signal input from the master controller (IC501), reset signal generator (IC652) and reset switch (SW503) "L": reset For several hundreds msec. after the power supply rises, "L" is input, then it changes to "H" Main system clock output terminal (10 MHz) Main system clock input terminal (10 MHz) Ground terminal Sub system clock output terminal (32.768 kHz) Not used (open) Sub system clock input terminal (32.768 kHz) Not used (fixed at "L") Ground terminal (for A/D converter) Reference voltage input terminal (+5V) (for A/D converter) Initial reset signal input terminal (A/D input) (fixed at "H") Temperature sensor (TH501) input terminal (A/D input) Select the number of load/eject aging times (A/D input) 0H 54H (30 times), 55H OA9H (20 times), OAAH OFFH (10 times) Select the digital output bits (A/D input) Chip select signal output to the external EEPROM device Not used (open) Serial data transfer clock signal output to the external EEPROM device Not used (open) Two way data bus with the external EEPROM device Not used (open) Writing serial data signal output to the CXD2652AR (IC301) and CXA2523AR (IC302) Unilink on/off control signal output for the SONY bus "L": link on, "H": link off
44
Pin No. 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 to 77 78 to 80
Pin Name UNIREQ UNICKIO UNISI UNISO MD-CKO MD-SI NCO SENS CC-XINT LIMIT-IN EJT-KEY ERROR-PWM MD-RST BU-IN BUS-ON SQSY C-SW MD-LAT MD-ON DEEMP A-MUTE NCO TSTCKO TSTSO TSTMOD VCC NIL
TOUT0 to TOUT3
I/O O I/O I O O I O I I I I O O I I I I O O O O O O O I -- I O I/O
Description Data request signal output terminal (for SONY bus) "H": request on Not used (open)
Serial clock signal input from the master controller (IC501) or serial clock signal output to the SONY bus interface (IC701) and master controller (IC501) (for SONY bus) Serial data input from the SONY bus interface (IC701) Serial data output to the SONY bus interface (IC701) Serial data transfer clock signal output to the CXD2652AR (IC301) and CXA2523AR (IC302) Reading serial data signal input from the CXD2652AR (IC301) Not used (open) Internal status (SENSE) input from the CXD2652AR (IC301) Interrupt status input from the CXD2652AR (IC301) Detection input from the sled limit-in detect switch The optical pick-up is inner position when "L" Eject request signal input terminal "L": eject on Not used (fixed at "H") Not used (open) PWM error monitor output terminal (C1and ATER is output when test mode)
Reset signal output to the PCM1718E (IC101), CXD2652AR (IC301) and BH6511FS (IC303) "L": reset Battery detect signal input from the SONY bus interface (IC600) and battery check circuit "H": battery on SONY bus on/off control signal input from the master controller (IC700) "L": bus on Subcode Q sync (SCOR) input from the CXD2652AR (IC301) "L" is input every 13.3 msec Almost all, "H" is input Inputs the disc loading start or disc eject completion detect switch detection signal "L": When start or eject completed of the disc loading operation Serial data latch pulse signal output to the CXD2652AR (IC301) and CXA2523AR (IC302) Power supply on/off control signal output of the MD mechanism deck section main power supply "H": power on Emphasis on/off control signal output to the PCM1718E (IC101) "H": emphasis on Audio muting on/off control signal output terminal Not used (open) Output of clock signal for the test mode display Output of data for the test mode display Power supply terminal (+5V) Not used (fixed at "H") Output of the 4×8 matrix test keys Not used (open) Not used (open) Input of the 4×8 matrix test keys ("L" is always output, except in test mode) Not used (open) Not used (open)
Setting terminal for the test mode "L": test mode, "H": normal mode
TIN0 to TIN2
*1 Loading motor (M903) control Operation Terminal LOAD (pin 6) EJECT (pin 7) IN "H" "L" OUT "L" "H" BRAKE "H" "H" STOP "L" "L"
45
· MAIN BOARD IC501 MB90574PMT-G-266-BND (MASTER CONTROLLER) Pin No. 1 2 3 4 to 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 to 28 29 30, 31 32 33 34 35 36 37 38 39 40, 41 42 Pin Name TUNON ANT CUT BUSON NCO ILLON VCC E2P SIO E2P CKO SYSRST DOORSW LCDSO LCDCKO LCDCE BEEP UNISI UNISO UNICKO UNICKI CD MD FLASHW NCO SIRCS NCO DOORIND NCO NS MASK VSS C AD ON REIN0 REIN1 DVCC DVSS NCO AVCC I/O O O O O O -- I/O O O I O O O O I O O I I I O I O O O O -- -- O I I -- -- O -- Description Tuner system power supply on/off control signal output to the BA4908 (IC671) "H": tuner power on Tuner system power supply on/off control signal output terminal "H": tuner power on Not used (open) Bus on/off control signal output to the MD mechanism controller (IC501) and SONY bus interface (IC701) "L": bus on Not used (open) Power on/off control signal output of the illumination LED and liquid crystal display driver (IC901) "H": power on Power supply terminal (+5V) Two-way data E2P bus with the FM/AM tuner unit (TU1) E2P bus clock signal output to the FM/AM tuner unit (TU1) System reset signal output to the MD mechanism controller (IC501) and SONY bus interface (IC701) "L": reset Front panel open/close detection signal input terminal "L" is input when the front panel is closed Serial data output to the liquid crystal display driver (IC901) Serial data transfer clock signal output to the liquid crystal display driver (IC901) Chip enable signal output to the liquid crystal display driver (IC901) "H" active Beep sound drive signal output to the power amplifier (IC611) Serial data input from the SONY bus interface (IC701) Serial data output to the SONY bus interface (IC701) Serial clock signal output to the MD mechanism controller (IC501) and SONY bus interface (IC701) Serial clock signal input from the MD mechanism controller (IC501) (for SONY bus) Setting terminal for the internal mechanism CD or MD "L": CD, "H": MD (fixed at "H" in this set) Internal flash memory data write mode detection signal input terminal "L": data write mode Not used Not used (open) Sircs remote control signal input from the remote control receiver (IC951) Not used (open) LED drive signal output of the MD disc slot illumination and Z indicator (LED810, LSW810) "H": LED on "H" is output to turn on LED when front panel is opened Not used (open) Discharge control signal output for the noise detection circuit "H": discharge Ground terminal Connected to coupling capacitor for the power supply A/D converter power control signal output terminal When the KEYACK (pin uh) that controls reference voltage power for key A/D conversion input is active, "L" is output from this terminal to enable the input Dial pulse input of the rotary encoder (RE901) (for VOLUME/BASS/TREBLE/BALANCE/FADER control) Power supply terminal (+5V) (for D/A converter) Ground terminal (for D/A converter) Not used (open) Power supply terminal (+5V) (for analog system)
46
Pin No. 43 44 45 46
Pin Name AVRH AVRL AVSS KEYIN0
I/O I I -- I
Description Reference voltage (+5V) input terminal (for A/D converter) Reference voltage (0V) input terminal (for A/D converter) Ground terminal (for analog system) Key input terminal (A/D input) (LSW901 to LSW908, S901 to S904) OFF, SOURCE, SOUND, MENU, PTY DSPL, LIST, ENTER, MODE, SEEK/AMS - . m + > M, DISC/PRST +, PRST/DISC - keys input Key input terminal (A/D input) (LSW810, LSW909 to LSW917) Z, D-BASS, TA, FA, 6 to 3 SHUF 2, REP 1 keys input Rotary remote commander key input terminal (A/D input) Destination setting terminal (fixed at "L" in this set) Noise level detection signal input at SEEK mode (A/D input) FM AGC detection signal input from the FM/AM tuner unit (TU1) (A/D input) Multi-path detection signal input from the RDS decoder (IC51) (A/D input) FM and AM signal meter voltage detection input from the FM/AM tuner unit (TU1) (A/D input) Power supply terminal (+5V) Internal RAM reset detection signal input terminal Input terminal to check that RAM data are not destroyed due to low voltage This checking is made within 100 msec after reset Not used (fixed at "H") Muting on/off control signal output of the FM/AM tuner signal "H": muting on Pre amplifier muting on/off control signal output to the electrical volume (IC151) "L": muting on Audio line muting on/off control signal output terminal "H": muting on Standby on/off control signal output to the power amplifier (IC611) "L": standby mode, "H": ampifier on Power amplifier muting on/off control signal output to the power amplifier (IC611) "L": muting on Setting terminal for the illumination color "L": 2 color, "H": 1 color (fixed at "H" in this set) Setting terminal for the illumination color "L": amber, "H": green (fixed at "L" in this set) Ground terminal Data transmit completed detection signal input from the RDS decoder (IC51) "H" active Setting terminal for the custom file "L": unavailable, "H": available (fixed at "H" in this set) Setting terminal for the CD text "L": unavailable, "H": available (fixed at "H" in this set) Front panel block remove/attach detection signal input from the nose detection switch (SW504) "L": front panel is attached Not used (open) Two-way data I2C bus with the FM/AM tuner unit (TU1), RDS decoder (IC51) and electrical volume (IC151) I2C bus clock signal output to the FM/AM tuner unit (TU1), RDS decoder (IC51) and electrical volume (IC151) Not used (open) Sub system clock output terminal (32.768 kHz) Sub system clock input terminal (32.768 kHz) Not used (open) Input of acknowledge signal for the key entry Acknowledge signal is input to accept function and eject keys in the power off status On at input of "H" Battery detection signal input from the SONY bus interface (IC701) and battery detect circuit "L" is input at low voltage
47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68, 69 70 71 72 73 74 75 76 77
KEYIN1 RCIN0 DSTSEL QUALITY FMAGC MPTH VSM VCC RAMBU TUNATT VOLATT ATT AMPON AMPATT COLSW COLSEL VSS DAVN FILE TEXT NOSESW NCO I2C SIO I2C CKO NCO X1A X0A NCO KEYACK BUIN
I I I I I I I -- I O O O O O I I -- I I I I O I/O O O O I O I I
47
Pin No. 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 to 97 98 99 100, 101 102 103 104 105 106 107 108 109 110 111 112 113 114
Pin Name ILLIN TELATT NCO TEST IN ACC IN NCO LOCKIN RCIN1 HSTX MD2 MD1 MD0 RSTX VSS X0 X1 VCC NCO DIM SEL TAP CD NCO AMTL IN AMS IN REEL POS0 POS1 POS2 POS3 LM EJ LM LD CM ON TAPON N ROUT AMSON
I/O I I O I I O I I I I I I I -- I O -- O I I O I I I I I I I O O O O O O
Description Auto dimmer control illumination line detection signal input terminal "H" is input at dimmer detection Not used (fixed at "L") Telephone detection signal input terminal At input of "H", the signal is attenuated by 20 dB Used for the MDX-C6500R/C6500RX only (MDX-C6400R: fixed at "L") Not used (open) Setting terminal for the test mode "L": test mode, Normally: fixed at "H" Accessory detection signal input terminal "L": accessory on Not used (open) Mini-disc lock detection signal input from the MD mechanism controller (IC501) "H": lock Rotary remote commander shift key input terminal "L": shift Hardware standby input terminal "L": hardware standby mode Reset signal input in this set Setting terminal for the CPU operational mode (fixed at "L" in this set) Setting terminal for the CPU operational mode (fixed at "H" in this set) Setting terminal for the CPU operational mode (fixed at "H" in this set) System reset signal input from the reset signal generator (IC652) and reset switch (SW503) "L": reset "L" is input for several 100 msec after power on, then it changes to "H" Ground terminal Main system clock input terminal (3.68 MHz) Main system clock output terminal (3.68 MHz) Power supply terminal (+5V) Not used (open) Setting terminal for the dimmer "L": dimmer in, "H": no dimmer (fixed at "H" in this set) Setting terminal for the internal mechanism tape or CD "L": CD, "H": tape (fixed at "L" in this set) Not used (open) Auto metal detection signal input terminal "L": auto metal Not used (open) Input terminal of whether a music is present or not is detected at auto music sensor "L": music is present, "H": music is not present Not used (open) Rotation detect signal input terminal Not used (open) Tape position (EJECT/FF/REW/REV/ FWD mode) detect input from the tape operation switch on the deck mechanism Not used this function (open) POS0: "L": EJECT mode, "H": others mode POS1: "L": FF and FWD mode, "H": others mode POS2: "L": REW mode, "H": others mode POS3: "L": REV and EJECT mode, "H": others mode
Loading motor control signal output terminal "H" active (For the eject direction and reverse side operation) Not used (open) Loading motor control signal output terminal "H" active (For the loading direction and forward side operation) Not used (open) Capstan/reel motor control signal output terminal "H": motor on Not used (open) Tape system power supply on/off control signal output terminal "H": tape on Not used (open) Forward/reverse direction control signal output terminal "L": forward direction, "H": reverse direction Not used (open) Tape auto music sensor control signal output terminal "L" is output to lower the gain for audio level at FF/REW mode Not used (open) METAL control in/out terminal At initial mode: auto/manual mode selection input of METAL function (manual at "L" input) At manual mode: METAL on/off control signal output terminal (METAL on at "H" output) Not used this function (open)
115
MTLON
I/O
48
Pin No.
Pin Name
I/O
Description Dolby control in/out terminal At initial mode: valid/invalid selection input of dolby function (valid at "L" input) At normal mode: dolby on/off control signal output terminal (dolby on at "H" output) Not used this function (open) Audio signal select control signal output terminal Not used (open) Ground terminal Main system power supply on/off control signal output to the BA4908 (IC671) "H": power on Not used (open)
116
DOLON
I/O
117 118 119 120
TAPATT NCO VSS PW ON
O O -- O
49
Ver 1.2
SECTION 5 EXPLODED VIEWS
· Items marked "*" are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. · The mechanical parts with no reference number in the exploded views are not supplied. · Hardware (# mark) list and accessories and packing materials are given in the last of the electrical parts list. The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
NOTE: · -XX and -X mean standardized parts, so they may have some difference from the original one. · Color Indication of Appearance Parts Example: KNOB, BALANCE (WHITE) . . . (RED) Parts Color Cabinet's Color
#11
(1)
GENERAL SECTION
#11
13
14
B FU601 #3
11 12
MG-164NZ-138 #4
15
C6500R/ C6500RX #3 #2
#3
TU1
9 10 2
#4
A
16 21
#11
not supplied
3 4 7
22 8
B A
17
#11
Front panel section #10 #1 #10 #1
5 6
#12
18
19
#10
CNP811
1
Ref. No. 1 2 3 4 5 6 7 * 8 * 9 * 9 * 9 * 10 11 * 12 * 13 Part No. X-3378-458-1 X-3376-699-2 3-030-909-02 3-713-786-51 3-034-086-01 3-033-750-02 3-040-990-01 1-677-057-11 A-3294-867-A A-3294-868-A A-3294-943-A 3-041-011-01 3-376-464-11 3-040-998-01 3-041-017-01 Description PANEL ASSY, SUB GEAR ASSY DAMPER, OIL SCREW +P 2X3 SPRING (DOOR) DOOR (MD) BUTTON (EJECT) (Z) SUB BOARD MAIN BOARD, COMPLETE (C6400R) MAIN BOARD, COMPLETE (C6500RX) MAIN BOARD, COMPLETE (C6500R) HEAT SINK (REG) SCREW (+PTT 2.6X6), GROUND POINT BRACKET (IC) BRACKET (MD) Remark Ref. No. * * * * 14 15 15 16 17 Part No. 3-040-995-01 3-040-996-11 3-040-996-21 3-045-878-01 1-776-527-51 Description Remark
COVER HEAT SINK (2P) (C6400R) HEAT SINK (2P) (C6500R/C6500RX) PLATE (TU), GROUND CORD (WITH CONNECTOR) (ISO) (POWER) (C6400R)
17 * 18 19 * 21 * 22
1-776-527-61 CORD (WITH CONNECTOR) (ISO) (POWER) (C6500R/C6500RX) 3-040-994-21 CHASSIS X-3377-621-2 LOCK ASSY 3-045-877-01 CUSHION (TU) 3-045-828-01 INSULATED PLATE
CNP811 1-792-195-11 CABLE, FLEXIBLE, FLAT FU601 1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) (10A) TU1 A-3220-812-A TUNER UNIT (TUX-020)
50
(2)
FRONT PANEL SECTION
#13 not supplied (KEY board)
56 55 59 53 54 60 66 65 67 68
LCD901
64 63 62 61
52 69
51
Ref. No. 51 52 53 54 55 56 * 59 60 * 61 * 62 * 63
Part No. 3-041-010-01 3-040-987-01 3-040-986-01 3-041-003-01 3-040-980-01 3-040-981-01 3-040-997-01 1-694-660-11 3-041-371-01 3-040-993-01
Description
Remark
Ref. No. 64 65 66 67 68 69 69 69 LCD901
Part No. X-3378-398-1 3-935-151-01 3-040-989-01 3-041-005-11 3-041-006-01 X-3378-685-1 X-3378-686-1 X-3378-688-1 1-803-906-11
Description PANEL ASSY, FRONT BACK SPRING (OPEN) BUTTON (OPEN) BUTTON (D) (D-BASS) BUTTON (AF/TA)
Remark
BUTTON (1-6/M) (MODE. 1. 2. 3. 4. 5. 6) BUTTON (OFF) BUTTON (MENU/SOUND) BUTTON (LIST/ENTER) (DSPL. LIST. ENTER) BUTTON (SOURCE) KNOB (VOL) PLATE (LCD), GROUND CONDUCTIVE BOARD, CONNECTION SHEET (REFLECTOR) PLATE (LCD), LIGHT GUIDE
FRONT PANEL (SV) ASSY (C6500R) FRONT PANEL (SV) ASSY (C6400R) FRONT PANEL (SV) ASSY (C6500RX) DISPLAY PANEL, LIQUID CRYSTAL (C6400R/C6500R) LCD901 1-803-906-31 DISPLAY PANEL, LIQUID CRYSTAL (C6500RX)
3-040-992-01 HOLDER (LCD)
51
(3)
MECHANISM DECK SECTION-1 (MG-164NZ-138)
112
#8
113 114
111
#6
106 107 110 109 116 109 118 117 109 115
105
#6 #6
#6
104
111 105 108
103 103 104 102
101
#5
Ref. No. * 101 * 102 103 104 105 * 106 107 * 108 * 109
Part No. A-3326-036-A X-3376-799-1 3-032-714-02 3-921-111-01 3-919-273-01 X-3376-796-3 3-032-682-01 3-034-301-01 3-034-302-01
Description SERVO BOARD, COMPLETE CHASSIS ASSY, MD SPRING (FLOAT F), TENSION SPRING (FLOAT B), TENSION DAMPER, O