Text preview for : sony_MDX-61_service_manual.pdf part of Sony MDX-61 MDX-61 MiniDisk changer, Car audio -
Service Manual
Back to : sony_MDX-61_service_manua | Home
MDX-61
SERVICE MANUAL
Ver 1.1 2001.08
US Model Canadian Model AEP Model UK Model E Model
This set is automatic electrical adjustment. Model Name Using Similar Mechanism Base Mechanism Type Optical Pick-Up Name MDX-60 MG-798-133 KMS-193C/J2N
SPECIFICATIONS
System Mini disc digital audio system Laser Diode Properties Material: GaAlAs Wavelength: 780nm Emission Duration: Continuous Laser out-put Power: Less than 44.6µW* * This output is the value measured at a distance of 200 mm from the objective lens surface on the Optical Pick-up Block. Frequency response 2020,000 Hz Wow and flutter Below measurable limit Signal-to-noise ratio 95 dB Output Bus control output (8 PIN) Analog audio output (RCA PIN) Current drain 300 mA (MD playback) 600 mA (during loading or ejecting a disc) Dimensions Approx. 176×83.5×125 mm (7×33/8×5 in.) (w/h/d) not incl. projecting parts and controls Mass Approx. 1.1 kg (2 lb. 7 oz.) Power requirement 12 V DC car battery (negative ground) Supplied accessories Mounting hard ware (1 set) Bus cable 5.5 m (1) RCA pin cord 5.5 m (1) · U.S. and foreign patents licensed from Dolby Laboratories Licensing Corporation. · Design and specifications subject to change without notice.
Continued on next page
MINIDISC CHANGER
9-925-528-12
2001H0500-1 C 2001.8
Sony Corporation
e Vehicle Company Shinagawa Tec Service Manual Production Group
TABLE OF CONTENTS 1. 2. 3.
3-1. 3-2. 3-3. 3-4. 3-5. 3-6. 3-7. 3-8.
GENERAL ..................................................................... 3 DISASSEMBLY ............................................................ 7 DIAGRAMS
Block Diagram ................................................................... Printed Wiring Boards - Servo Section ........................... Schematic Diagram Servo Section .............................. Schematic Diagram Main Section ............................... Printed Wiring Boards Main Section ........................... Schematic Diagram Power Section ............................. Printed Wiring Board Power Section ........................... IC Pin Function Description .............................................. 11 13 15 20 23 26 29 33
SERVICING NOTE [To place this set in the play mode] This set does not have the key control function, and therefore it cannot activate the play mode by itself. Also, the key control to this set is done through a serial communication with the master unit (SONY Bus System compatible car audio, TV tuner, source selector, etc.). Accordingly, if repairing this set, connect as shown below:
Master unit (MDX-C150/ C150RDS, etc.)
MDX-61
4. 5.
EXPLODED VIEWS ................................................... 41 ELECTRICAL PARTS LIST .................................... 45
Bus control Bus control output terminalinput terminal
CAUTION
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE ! SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
2
SECTION 1 GENERAL
This section is extracted from instruction manual.
3
4
5
6
SECTION 2 DISASSEMBLY
Note: Follow the disassembly procedure in the numerical order given.
FRONT PANEL ASS'Y, CASE (UPPER)
5 case (upper)
1 two screws (B2.6 × 6)
1 two screws (B2.6 × 6) 2 claw
3 front panel ass'y 2 claw 4 connector (CN620)
1 two screws (B2.6 × 8)
REAR PANEL ASS'Y, MD SECTION
2 rear panel ass'y
6 two springs
4 two dampers 7
3 flexible board (CN800)
4 two dampers
5 two springs
6 two springs
7
CHASSIS (GEAR) ASS'Y, MAIN BOARD
1 three screws (P1.7 × 1.8) 2 chassis (gear) ass'y 3 special flat screw (1.7 × 3) 4 flexible board (CN500) 5 connector (CN602) 3 two special flat screws (1.7 × 3)
6 flexible board (CN610)
7 three connectors (CN603, 700, 701)
8 MAIN board
CHASSIS (BASE) ASS'Y, CHASSIS (OP) ASS'Y
3 worm wheel (LD) 5 Pull up the chassis (OP) ass'y in the arrow A direction.
1 four screws (P1.7 × 1.8)
A
1 screw (P1.7 × 1.8)
1 screw (P1.7 × 1.8)
2 feed screw (ELV) ass'y
4 chassis (base) ass'y
8
SERVO BOARD
2 three special head screws (M1.7 × 2) 3 flexible board (CN100)
5 connector (CN301) 6 servo board
1 flexible board (CN200)
4 flexible board (CN400)
OPTICAL PICK-UP (KMS-193C/J2N)
1 two screw (K1.7 × 3.5)
2 optical pick-up (KMS-193C/J2N)
9
SECTION 3 DIAGRAMS
· Circuit Boards Location
SW board
POWER board
MAIN board
LAMP board
SERVO board
10
MDX-61
3-1.
BLOCK DIAGRAM
IC100 RF AMP 12 2 10 7 F 4 C 3 B 48 J 2 A 5 D 6 E 47 I XRST 17 SWDT 18 SCLK 19 XLAT 20 RFO 44 AGCI 43 RF 41 TE 26 SE 29 ADFG 33 AUX 34 FE 35 AUTOMATIC POWER CONTROL Q100 14 AAPC BOTM 38 PEAK 39 58 RFI 77 TE 76 SE 82 ADFG 68 AUX1 67 FE 65 BOTM 64 PEAK XLAT 10 SCLK 9 SWDT 8 XRST 16 SENS 12 SRDT 11 SQSY 14 FOK 2 DTO 30 DTI 29 10 PD PD ABCD 37 66 ABCD DFCT 3 C2PO 31 BCK 32 LRCK 33 PEAK HOLD Q200 IC201 INVERTER APC REF 11 4 2 84 LDDR X500 45.1584MHz 78 AUX2 XTAI 35 97 MIN 92 C2PO 91 BCK 90 LRCK 87 SPO D OUT 41 36 OSC O ALRCK 44 37 OSCI IC501 RAM 13 HOME AO0 55 i 52 · 56 i AO8 60 D0 69 · 68 · 70 · D4 71 XOE XCAS A09 XRAS XWE 61 62 65 66 67 9 A0 i 12 · 14 i 18 A8 1 D0 · 2 · 24 · 25 D3 22 23 5 4 3 DE CAS AB RAS WE S901 (HOME POSITION DET) RV901 ELEVATOR HIGHTER POSITION DET(EHS) 40 EHS Q500, 501 SWITCHING MDMON 10 +9V (LINE AMP) +5V (PULL UP) 56 LIMIT-SW S400 (LIMIT DET) 14 DCS1 i 19 DCS6 IC950 REGULATOR CONTROL 14 13 10 7 4 3 +3.3V PL620 ILLUMINATION LAMP +3.3V REG. Q953 LAMP DRIVE Q600, 601 +5V REG. Q954 +5V (SYSTEM CONTROLLER) +5V (MOTOR DRIVE) +9V REG. Q940, 941 1 3 SERIAL INPUT DAC DAC LPF LPF 8 5 R-CH 3 IC550 D/A CONVERTER XLAT SCLK SWDT XRST SENS SRDT SQSY FOK 93 DATA X INT 9 1 2 55 CC-XINT A-MUT 67 MUTING SWITCH Q560, 561 IC800 LINE AMP + 1 2 +3.3V (D/A CONV) +3.3V REG. Q931 (L) R-CH MUTING CONTROL SWITCH Q800 (R) XRST SWDT SCLK XLAT IC200 DIGITAL SIGNAL PROCESSOR DIGITAL SERVO SIGNAL PROCESSOR, EFM/ACIRC ENCODER/DECODER IC500 SHOCK PROOF MEMORY CONTROLLER ATRAC ENCODER/DECODER XRST XLAT SWDT SCLK IC602 LEVEL SHIFT 4 XLAT 3 SCK 2 SWDT 17 XRST 6 SENS 5 SRDT SQSY FOK 9 11 8 10 62 SQSY BU-IN 60 64 FOK BATTERY DET Q920, 921 SRDT 5 6 52 MD-SI SENS 3 4 54 SENS BUS-ON 61 13 SW 2 59 MD-RST 58 MD-LAT 45 MD-SO 51 MD-CKO UNISO 50 UNISI 49 9 10 6 UNICKI 48 11 IC600 SYSTEM CONTROLLER RST 30 IC601 RESET 8 IC900 BUS INTERFACE RESET SW 7 4 8 4 5 6
OPTICAL PICK-UP BLOCK (KMS-193C/J2N) DETECTOR
CNP1 (BUS CONTROL CONNECTOR) 1 2 3 7
F
I
C B D A
J
9 8 4
E
5 3
LD
MUTING Q810, 820
LINE OUTPUT
4
CONTROL
DRIVER
8 FOCUS 11
6
87 FFDR
+6V REG. Q910, 911 Q950 B+ SWITCH +5V REG. Q952
5
89 FRDR
TRACKING 26
CONTROL
DRIVER
29
31
86 TFDR
32
85 TRDR
S611-616 (EJECT)
ERROR AMP COMP OUT OUT ERROR AMP
M901 SPINDLE
M
24 13
CONTROL
DRIVER
22
20
93 SPRD
57 DOOR-SW S620 DOOR OPEN /CLOSE DET 11 LES
COMP
19 18
94 SPFD 91 SRDR
M902 SLED
M
15
CONTROL
DRIVER
17
92 SFDR
S902 (LES) 12 SES IC700 ELEVATOR MOTOR DRIVE S903 (SES) ILL ON 21 6 M1 STR-SW 63 4 7 M1 XTAL 32 IC701 LOADING MOTOR DRIVE X600 10MHz EXTAL 31 8 M2 TX 34 X601 32.768kHz 4 9 M2 TEX 35 S600 (STOP) (SHASSIS)
IC300 SLED/SPINDLE MOTOR DRIVE, FOCUS/TRACKING COIL DRIVE
M904 (ELEVATOR)
M
7
· R-CH : Same as L-ch · SIGNAL PATH : PLAY M903 (LOADING)
M
7
11
CONTROL
DRIVER
9
CONTROL
DRIVER
9
2
2
12
· IC Block Diagrams
SERVO section
IC200 CXD2535CR-1
AUX FE ABCD BOTM DVDD ADRB AVDD ASYO ADRT AVSS AVSS PEAK FILO FILI PCO CLTV ADIO DICV ASYI BIAS DIFO BIA2 DIFI RFI VC
MAIN section
IC501
D1 1
HM51W4400TT6-8
26 GND 25 D4 24 D3
75 74 73 72 71 70
69 68 67 66 65 64 63 62 61 60
59
58 57 56 55 54
53 52 51 50 DVSS
CLOCK OSC
D2 2 XWE 3
SE 76 TE 77 TENV 78 MID 79 APC 80 TEST1 81 ADFG 82 TS25 83 LDDR 84 TRDR 85 TFDR 86 FFDR 87 DVDD 88 TRACKING PWM FOCUS PWM SLED PWM PWM GENERATOR
OP AMP A/D CONVERTER
ECC ENCODER/ DECODER REGISTER 32K RAM
TIMING GENERATOR
47 MVC1 46 RAOF EFM MODULATOR
NC 5 NC 6 NC 7 A0A9 COLUMN DECODER
(4) INPUT BUFFER
ANALOG MUX
34 MHz PLL
COMP
DIN PLL (22 MHz)
49 DIPO 48 TEST2
XRAS 4
23 XCAS 22 XOE 21 NC 20 NC
45 EFMO
A9 8
SENSE REFRESH AMP INPUT/OUTPUT CONTROL SWITCH
19 NC
ADDRESS BUFFER
ROW DECODER
(4) OUTPUT BUFFER
A0 9
18 A8 17 A7 16 A6 15 A5 14 A4
EFM DIGITAL PLL EFM SYNC DETECTOR/ PROTECTOR
A1 10
44 XPLCK 43 GFS 42 GTOP 41 WFCK
A2 11 A3 12 VDD 13
A0A9
REGISTER SERVO DSP TRACKING SERVO FOCUS SERVO SLED SERVO
EFM DEMODULATOR
MEMORY CELL (4194204 BIT)
40 RFCK 39 WDCK SUBCODE Q READER/ GENERATOR
TIMING GENERATOR
FRDR 89 FS4 90 SRDR 91 SFDR 92 SPRD 93 SPFD 94 DCLO 95 DCLI 96 XDCL 97
IC550
SDATAI 1 DEM/SCLK 2 LRCK 3
CS4330-KSR-H
VOLTAGE REFERENCE SERIAL INPUT INTERFACE INTERPOLATOR DELTA-SIGMA MODULATOR ANALOG LOW-PASS FILTER 8 7 6 5 AOUT L VA+ AGND AOUT R
IC700, 701
GND 1
LB1638M
10 N.C.
38 DVDD 37 XBCK 36 MCLK CLOCK GENERATOR 35 XTAI 34 XTAO 33 LRCK
ADIP DEMODULATOR
ADIP DECODER
DIGITAL CLV PROCESSOR
DAC
IN1 2
CONTROL LOGIC
9 OUT1 8 VS 7 OUT2
DE-EMPHASIS MCLK 4
APC COMP./ FILTER
APC PWM GENERATOR
SUBCODE P~W PROCESSOR AUDIO DATA CONTROL
32 BCK 31 C2PO 30 DTO 29 DTI 28 DIDT 27 DODT 26 DOVF
VCC 3 IN2 4 GND 5
SERVO AUTO SEQUENCER
SENS CONTROL
6 N.C.
OFTRK 98 COUT 99 DVSS 100
OFTRK/DFCT/ FOK/C OUT/ SHCK/TEOK PROCESSOR
DIGITAL AUDIO IN/OUT SERVO CONTROL CPU I/F PEAK DETECT
POWER section
IC900 MM1284XFFE
SW SW 14 VCC REF OUT 13 BUS ON 12 LINK OFF 11 CLK OUT
IC950
TL1451ACDB-E20
DEAD TIME CONTROL2 NON-INVINPUT2 INVINPUT2 FEED BACK2
1 2 3 4
TEOK FOK DFCT SHCK
5
SSTOP
6
WRPWR
7
DIRC
8 9 10 11
SCLK XLAT SRDT SWDT
12
SENS
13
ADSY
14 15 16
DQSY XRST SQSY
17 18 19
SBOCK SBODT SBIOT
20 21 22 23 24 25
FMCK DOUT DIN DVSS ADER REC
OUT2
S.C.P
BUS ON OUT 1 BUS ON INPUT 2
PGND
PGND
PGND
PGND
PGND
PGND
IC300
MPC17A38ZVMEL
RO1 FO1 VG VD VD VD
16 GND 3 BUS CLK 4 VREF 5 BUS DATA 6 10 DATA OUT +2.5V 9 DATA IN BUS RESET 7 RESET SW 8 RESET SHORT CIRCUIT PROTECTION COMPARATOR + + VREF/2 VERF. +2.5V VCC REFERENCE VOLTAGE
RO2 RO3 RO4 FO2 FO3 FO4 VD VD VD
15
14
13
12
11
10
36
7
12
16
8
11
9
10
15
13
14
21
25
30
29
26
27
28
22
24
23
+ ERROR AMP2 VERF VERF VERF PWM COMPARATOR2
OUTPUT2
G 1 DC/DC CONVERTER
DRIVER
DRIVER
DRIVER
DRIVER
OUTPUT1 S R LATCH R U.V.L.O PWM COMPARATOR1
PRE-DRIVER VC CLOCK CLK DETECTOR VC CONTROL VC VC VC
PRE-DRIVER VC
PRE-DRIVER VC
PRE-DRIVER
CONTROL VC
CONTROL VC
CONTROL
TRIANGLE OSCILLATOR 1 2 RT 3 NON-INVINPUT1 4 INVINPUT1
+ ERROR AMP1 GND 5 FEED BACK1 6 DEAD TIME CONTROL1 7 OUT1 8 GND
VC 2
VC
3
CLK
34
PS
6
FI1
5
RI1
33
OE
17
FI2
18
RI2
31
FI3
32
RI3
20
F/R4
19
PI4
4
GND
35
GND
31
32
CT
VCC 9
3-8.
IC PIN FUNCTION DESCRIPTION
Pin Name VC A-F FI FO PD APCREF TEMPI GND AAPC DAPC TEMPR XRST SWDT SCLK XLAT VREF TENV THLD VCC TFIL TE TLB CSLED SE ADFM ADIN ADAGC ADFG AUX FE FLB ABCD BOTM PEAK PFAGC RF ISET AGCI RFO MORFI MORFO I, J I/O O I I O I I I O O O I I I I O O I I O I I O O I I O O O I O O O I O I I O I O I Function Output terminal for the center point voltage (1/2 VCC) generated Signal input from detector circuit in the optical pick-up block Signal input of the operational amplifier for F signal Signal output of the operational amplifier for F signal Front monitor Connected to the photo diode Not used this set (OPEN) Input terminal for the setting of laser power Terminal for the connection to temperature sensor Ground terminal LD amplifier output terminal of APC circuit Not used (OPEN) Output terminal of the reference voltage for temperature sensor Reset signal input from the system controller (IC600) Clock signal input from the system controller (IC600) Latch signal input from the system controller (IC600) Reference voltage output Not used (OPEN) Not used (OPEN) Power supply terminal (+3.3V) Not used (OPEN) Tracking error signal output to CXD2535CR (IC200) Input terminal of the adder signal to tracking error Terminal for the sled error lowpass filter Sled error signal output to CXD2535CR (IC200) FM signal output terminal of the ADIP Input terminal by AC coupling is FM signal of the ADIP External capacitor connect terminal for AGC of the ADIP ADIP double turned FM signal output to CXD2535CR (IC200) Sub signal output to CXD2535CR (IC200) Focus error signal output to CXD2535CR (IC200) Input terminal of the adder signal to focus error Light amount signal output to CXD2535CR (IC200) Light amount bottom hold signal output to CXD2535CR (IC200) Light amount peak hold signal output to CXD2535CR (IC200) External capacitor connect terminal of AGC circuit for the RF Playback EFM RF signal output to CXD2535CR (IC200) Setting terminal for the internal circuit constant Input terminal by AC coupling is RF signal RF signal output terminal Input terminal by AC coupling is RF signal of the MO RF signal output terminal of the MO Signal input from detector circuit in the optical pick-up block 22kHz, BPF center frequency Not used this set (OPEN) (22.05kHz ± 1kHz) Not used this set (OPEN) Not used this set (OPEN) Write data signal input from the system controller (IC600) Not used this set (OPEN) When reset : "L"
SERVO BOARD IC100 CXA1981AR (RF AMP) Pin No. 1 2-7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47, 48
33
SERVO BOARD IC200 CDX2535CR-1 (DIGITAL SIGNAL PROCESSOR, DIGITAL SERVO SIGNAL PROCESSOR, EFM/ACIRC ENCODER/DECODER) Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 Pin Name FS256 FOK DFCT SHCK SHCKEN WRPWR DIRC SWDT SCLK XLAT SRDT SENS ADSY SQSY DQSY XRST TEST4 CLVSCK TEST5 DOUT DIN FMCK ATER REC DVSS DOVF DODT DIDT DTI DTO C2PO BCK LRCK XTAO XTAI MCLK XBCK DVDDO WDCK RFCK I/O O O O O I I I I I I O O (3) O O O I I O I O I O O I I I O I O (3) O O O O I O O O O Function 11.2896MHz clock signal output (MCLK system) Not used this set (OPEN) "H" is output when the focus is applied Not used this set (OPEN) Not used this set (Fixed at "L") Focus OK signal output to the system controller (IC600)
Defect ON/OFF selection signal output to CXD2536CR (IC500) Track jump detection signal output to the system controller Track jump detection enable input Not used this set (Fixed at "H") Write data signal input from the system controller (IC600) Serial clock signal input from the system controller (IC600) Serial latch signal input from the system controller (IC600) Read data signal output to the system controller (IC600) Internal status (SENS) output to the system controller (IC600) ADIP sync signal output Not used this set (OPEN) Sub-code Q sync (SCOR) output to the system controller (IC600) "L" every 13.3msec, Almost "H" Digital in U-bit CD format sub-code Q sync (SCOR) output to the system controller (IC600) "L" every 13.3msec, Almost "H" Reset sigmal input from the system controller (IC600) Test input terminal (Fixed at "L") Not used this set (OPEN) Test input terminal (Fixed at "L") Output terminal of the digital audio signal (for optical out) Input terminal of the digital audio signal (for optical out) FM modulation clock signal output of the ADIP ADIP CRC flag output When error "H" Record/playback selection signal input When recording :"H", when playback :"L" Ground terminal (Digital system) Validity flag input terminal for the digital audio out Not used this set (Fixed at "L") Not used this set (Fixed at "L") Not used this set (OPEN) Input terminal of 16-bit data signal for the digital audio out Output terminal of 16-bit data signal for the digital audio in Record audio data signal input from CXD2536CR (IC500) Plyback audio data signal output to CXD2536CR (IC500) C2PO (indicate the error state of the data) signal output to CXD2536AR (IC500) Playback : C2PO ("H"), Digital recording : D. In-Vflag, Analog recording : "L" Bit clock (2.8224MHz) signal output to CXD2536CR (IC500) (MCLK system) L/R clock (44.1kHz) signal output to CXD2536CR (IC500) (MCLK system) System clock (512Fs=22.5792MHz) signal output MCLK clock (22.5792MHz) signal output BCK (pin #TM) inverted output Not used this set (OPEN) System clock (512Fs=22.5792MHz) signal input from CXD2536CR (IC500) Not used this set (OPEN) Not used this set (OPEN) Not used this set (OPEN) Not used this set (OPEN) (Fixed at "L") Not used this set (OPEN) Not used this set (Fixed at "L") When reset "L" Laser power selection signal input from the system controller Not used this set (Fixed at "L")
Not used this set (OPEN)
Not used this set (OPEN)
Power supply terminal (+3.3V) (Digital system) WDCK clock (88.2kHz) signal output (MCLK system) RFCK clock (7.35kHz) signal output (MCLK system)
34
Pin No. 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78
Pin Name WFCK GTOP GFS XPLCK EFMO RAOF MVCI TEST2 DIPD DVSS1 DICV DIFI DIFO AVDD1 ASYO ASYI BIAS RFI AVSS1 CLTV PCO FILI FILO PEAK BOTM ABCD FE AUX1 VC ADIO TEST3 AVDD2 ADRT ADRB AVSS2 SE TE AUX2
I/O O O O O O O I I O (3) I (A) I (A) O (A) O I (A) I (A) I (A) I (A) O (3) I (A) O (3) I (A) I (A) I (A) I (A) I (A) I (A) O (A) I (A) I (A) I (A) I (A) I (A) I (A) When recoding : EFM encoder PLL system)
Function WFCK clock (7.35kHz) signal output (When playback : EFM decoder PLL system, Not used this set (OPEN) Not used this set (OPEN) Opens the playback EFM frame sync protection window when "H" Not used this set (OPEN) EFM decoder PLL clock (98Fs=4.3218MHz) signal output the EFM signal match Not used this set (OPEN) FM signal output (When recoding) Falling edge of the EFM PLL clock and
The playback EFM frame sync and interpolation protection timing match when "H"
Not used this set (OPEN)
Overflow detection signal output of the internal RAM (Decoder monitor out) RAOF is signal generated when the 32k RAM exceeds the ±4F jitter margin Not used this set (OPEN) Oscillation input for PLL of the digital in Test terminal input (Fixed at "L") Phase comparator output for PLL of the digital in When the external VCO : Frequency ; Low"L" Ground terminal (Digital system) Control voltage input terminal of the internal VCO for digital in PLL Filter input terminal of the internal VCO for digital in PLL Filter output terminal of the internal VCO for digital in PLL Power supply terminal (+3.3V) (Analog system) Playback EFM full-swing output (L=VSS, H=VDD) Playback EFM asymmetry comparate voltage input terminal Playback EFM asymmetry circuit constant current input terminal Playback EFM RF signal input from CXA1981AR (IC100) Ground terminal (Analog system) VCO control voltage input terminal of the PLL for decoder PLL master clock Phase comparator output terminal of the PLL for decoder PLL master clock Filter input terminal of the PLL for decoder PLL master clock Filter output terminal of the PLL for decoder PLL master clock Light amount peak hold signal input from CXA1981AR (IC100) Light amount bottom hold signal input from CXA1981AR (IC100) Light amount signal input from CXA1981AR (IC100) Focus error signal input from CXA1981AR (IC100) Sub signal input from CXA1981AR (IC100) Center point voltage (1/2 VCC) Test input terminal (Fixed at "L") Power supply terminal (+3.3V) (Analog system) A/D converter action limits (upper side) voltage input (Fixed at "H") A/D converter action limits (lower side) voltage input (Fixed at "L") Ground terminal (Analog system) Sled error signal input from CXA1981AR (IC100) Tracking error signal input from CXA1981AR (IC100) Sub signal input terminal from CXA1981AR (IC100) input from CXA1981AR (IC100) Not used this set (OPEN) Monitor output of the A/D converter input signal Not used this set (Fixed at "L") Not used this set (OPEN) When the internal VCO : Frequency ; Low"H" Not used this set (OPEN) Not used this set (Fixed at "L")
35
Pin No. 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100
Pin Name DCHG APC TEST1 ADFG TS25 LDDR TRDR TFDR FFDR DVDD1 FRDR FS4 SRDR SFDR SPRD SPFD DCLO DCLI XDCL OFTRK COUT DVSS2
I/O I (A) I (A) I I I O O O O O O O O O O O I O O O Connected to the Ground Input terminal for the laser APC Test input terminal (Fixed at "L")
Function Not used this set (Fixed at "L")
ADIP double turned FM signal input from CXA1981AR (IC100) (22.05kHz ± 1kHz) (TTL schmitt input) Test input terminal (Fixed at "L") Laser APC signal output to CXA1981AR (IC100) Tracking servo drive signal outuput () Tracking servo drive signal outuput (+) Focus servo drive signal output (+) Power supply terminal (+3.3V) (Digital system) Focus servo drive signal output () 176.4kHz clock signal output (MCLK system) Sled servo drive signal output (+) Sled servo drive signal output () Spindle servo drive signal output (+) Spindle servo drive signal output () Not used (OPEN) Not used (Fixed at "H") Not used (OPEN) Offtrack signal output Not used this set (OPEN) Not used this set (OPEN) Traverse count signal output Not used this set (OPEN)
Ground terminal (Digital system)
*: On I/O section (3): 3 state output
(A): Analog output
36
MAIN BOARD IC500 CXD2536R (SHOCK PROOF MEMORY CONTROLLER, ATRAC ENCODER/DECODER) Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18-21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45-47 48, 49 Pin Name VDD SWDT SCK XLAT SRDT SENSE SMDO SMDI XINT RCPB WRMN TX VSS SICK IDSL XILT XRST TS0-TS3 EXIR SASL SGL VSS AIRCPB XRQ ADTO ADTI XALT ACK AC2 LCHST EXE MUTE OSCO OSCI VSS ATT F86 DOUT ADIN ABCK ALRCK SA2-SA0 A11,A10 I/O I I I O/Z O/Z I I O I I I I I I I I I I I O I/O I/O I/O I/O I/O I/O I/O I/O I/O O I I/O O O I O O O O Power supply terminal (+3.3V) Write data signal input from the system controller (IC600) Serial clock signal input from the system controller (IC600) Serial latch signal input from the system controller (IC600) Read data signal output to the system controller (IC600) Internal status (SENSE) output to the system controller (IC600) Serial command control mode input from the system controller (Fixed at "H") Serial command control mode input from the system controller (Fixed at "H") Interruption status output to the system controller (IC600) Record/playback selection signal input (Fixed at "L") Write/monitor mode selection signal input from the system controller (Fixed at "L") Writing data transmission timing input from the system controller Used together with the magnetic field head ON/OFF output (Fixed at "L") Ground terminal Chip reserve terminal (Fixed at "H") Chip reserve terminal (Fixed at "H") Chip reserve terminal (Fixed at "H") Reset signal input from the system controller (IC600) Test input terminal (Fixed at "L") Chip reserve terminal (Fixed at "L") Single use the block selection Ground terminal Record/playback mode signal output terminal of the ATRAC or external audio block Not used this set (OPEN) XRQ signal input/output terminal of the ATRAC interface Not used this set (OPEN) Decoder data signal input/output terminal of the ATRAC Encoder data signal input/output terminal of the ATRAC Not used this set (OPEN) Not used this set (OPEN) "L" : ATRAC, "H" : RAM controller (Fixed at "L") Normally fixed at "L", Fixed at "H" when the ATRAC or RAM controller is single used (Fixed at "L") When reset : "L" Function
Data ready and XALT signal input/output terminal of the ATRAC interface Not used this set (OPEN) ACK signal input/output terminal of the ATRAC interface Not used this set (OPEN) Error data signal input/output terminal of the ATRAC interface EXE signal input/output terminal of the ATRAC interface 45.1584MHz clock oscillation output 45.1584MHz clock oscillation input Ground terminal ATT signal input/output terminal of the ATRAC interface Not used this set (OPEN) 11.6msec timing signal output terminal of the ATRAC block Recording data signal input Bit clock signal output Address signal output Address signal output Not used this set (Fixed at "L") Not used this set (OPEN) Monitor/audio decode data signal output to the D/A converter (IC550) Not used this set (OPEN) Not used this set (OPEN) Not used this set (OPEN) Not used this set (OPEN) Lch Start data signal input/output terminal of the ATRAC interface Not used this set (OPEN) Not used this set (OPEN) MUTE signal input/output terminal of the ATRAC interface Not used this set (OPEN)
L/R clock signal output to the D/A converter (IC550)
37
Pin No. 50 51 52-55 56-60 61 62 63 64 65 66 67 68,69 70,71 72-74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100
Pin Name VSS VDD A03-A00 A04-A08 XOE XCAS VSS XCS A09 XRAS XWE D1,D0 D2,D3 D4-D6 VSS D7 ERR EXTC2R BUSY EMP FUL EQL MDLK CPSY CTMD0 CTMD1 SPO VSS MDSY LRCK BCK C2PO DATA DIDT DODT DIRCPB MIN SPOSL MCK VSS
I/O O O O O O O O O I/O I/O I/O I/O I/O I O O O O O O O O O O I I I I/O I O O I I O Ground terminal Power supply terminal (+3.3V) Address signal output to the RAM (IC501) Address signal output to the RAM (IC501)
Function
Output enable control signal output to the RAM (IC501) Column address strobe signal output to the RAM (IC501) Ground terminal Chip select signal output Not used this set (OPEN) Address signal output to the RAM (IC501) Row address strobe signal output to the RAM (IC501) Reading/Writing control signal output to the RAM (IC501) RAM (IC501) data bus RAM (IC501) data bus Data bus Data bus Not used this set (OPEN) Not used this set (OPEN) Ground terminal Input /output terminal of the error (C2PO) data signal to the external RAM Not used this set (OPEN) External RAM selection signal input for the error data writing (Fixed at "L") BUSY signal output of the RAM access Not used this set (OPEN) Not used this set (OPEN) Not used this set (OPEN) Empty or before the full of the ATRAC data (When DSC=ASC+1 : "H") Full or before the empty of the ATRAC data (When ASC=DSC+1 : "H") Empty of the ATRAC data (When DSC=ASC : "H") Indicate the main/sub of the recording or playback data (When sub and linking : "H", When the main : "L") Not used this set (OPEN) Not used this set (OPEN) Not used this set (OPEN) Not used this set (OPEN) Interpolation sync signal output (When "H" : External RAM)
DSC (Difference Signal Control) counter mode output DSC (Difference Signal Control) counter mode output Ground terminal Sync detection signal output of the main data
System clock (512Fs=22.5792MHz) signal output to CXD2535CR (IC200) and D/A converter (IC550) Not used this set (OPEN)
L/R clock (44.1kHz) signal input from CXD2535CR (IC200) Bit clock (2.8224MHz) signal input from CXD2535CR (IC200) C2PO (indicate the error mode of the data) signal input from CXD2535BR (IC200) When playback : C2PO ("H"), When digital recording : D. IN-Vflag, When analog recording : "L" When recording : Record audio data signal output (Not used this set) When playback : Playback audio data signal input from CXD2535CR (IC200) 16-bit data input terminal for the digital audio in 16-bit data output terminal for the digital audio out Not used this set (Fixed at "L") Not used this set (OPEN) Not used this set (OPEN)
Disc drive, Record or playback mode output of the EFM encoder/decoder Defect ON/OFF selection signal input from CXD2535CR (IC200)
IN/OUT selection input terminal of the pin *¶ ("L" : IN, "H" : OUT) (Fixed at "H") Internal master clock signal output terminal of the RAM controller Ground terminal
38
MAIN BOARD IC600 CXP84340-043Q (SYSTEM CONTROLLER) Pin No. 1-5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22-29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 Pin Name T13-T17 M1 M1 M2 M2 MDMON LES SES HOME DCS1 DCS2 DCS3 DCS4 DCS5 DCS6 CH/SINGLE ILLON N.C. RST EXTAL XTAL VSS TX TEX AVSS AVREF INIT TEMP EHS N.C. EE-CS EE-CKO EE-SIO MD-SO LNKOFF UNIREQ UNICKI UNISI UNISO MD-CKO MD-SI N.C. SENS CC-XINT I/O I O O O O O I I I I I I I I I I O O I I O O I I I I O O O I/O O O O I I O O I O I I Test key (4 × 8 matrix) signal output terminal Function (Fixed at "L") *1 Elevator motor (M904) drive signal output (UP) Loading motor (M903) drive signal output *2 Loading motor (M903) drive signal output *2 Power control output (Mechanism deck system) Power ON : "H" Detection signal input from the loading end sensor switch (S902) Detection signal input from the store end sensor switch (S903) Detection signal input from the home position switch (S901) Detection signal input from the disc1 switch (S611) Detection signal input from the disc2 switch (S612) Detection signal input from the disc3 switch (S613) Detection signal input from the disc4 switch (S614) Detection signal input from the disc5 switch (S615) Detection signal input from the disc6 switch (S616) Changer/single setting up terminal Not used (OPEN) System reset signal input When reset : "L" 10MHz system clock signal input 10MHz system clock signal output Ground terminal 32.768kHz clock signal output for a clock 32.768kHz clock signal input for a clock Ground terminal (Analog system) Reference voltage (+5V) input for the A/D converter Initial reset signal input (Normally : "H") Temperature detection signal input Disc hight position detection signal input Not used (OPEN) Chip select signal output for a EEPROM Serial clock signal output for a EEPROM Data signal input/output for a EEPROM Not used this set (OPEN) Not used this set (OPEN) Not used this set (OPEN) Not used this set (OPEN) Lamp (PL620) drive signal outuput for illumination Home position : "L" No disc "L" No disc "L" No disc "L" No disc "L" No disc "L" No disc "L" When lamp is ON : "H"
Elevator motor (M904) drive signal output (DOWN) *1
When used the changer : "H" (Fixed at "H")
Write data signal output to RF AMP (IC100), CXD2535CR (IC200) and CXD2536CR (IC500) LINK OFF signal output for serial communications Clock signal (serial communications) input Data signal (serial communications) input Data signal (serial communications) output Serial clock signal output to RF AMP (IC100), CXD2535CR (IC200) and CXD2536CR (IC500) Read data signal input from CXD2535CR (IC200) and CXD2536CR (IC500) Not used Internal status (SENS) input from CXD2535CR (IC200) and CXD2536CR (IC500) Interruption stsatus input from CXD2536CR (IC500) Request signal output for serial communications Not used this set (OPEN)
39
Pin No. 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80
Pin Name LIMIT-SW DOOR-SW MD-LAT MD-RST BU-IN BUS-ON SQSY STR-SW FOK MD-ON EMPH-O A-MUT N.C. CLOCK DATA TM-ON/OFF VDD N.C. TO0 TO1 TO2 TO3 TI0 TI1 TI2
I/O I I O O I I I I I O O O O O O I O O O O I I I
Function Detection signal input from the limit switch (S400) When sled limit in : "L" When open : "L"
Detection signal input from the door open/close switch (S620)
Serial latch signal output to RF AMP (IC100), CXD2535CR (IC200) and CXD2536CR (IC500) Reset signal output to RF AMP (IC100), CXD2535CR (IC200) and CXD2536CR (IC500) When reset "L" Battery detection signal input BUS-ON detection signal (serial communications) input "L" every 13.3msec, Almost "H" Detection signal input from the STOP switch (S600) Focus OK signal input from CXD2435CR (IC200) Power control signal output (Servo system) Audio mute signal output Not used (OPEN) Clock signal output for test mode indication Data signal output for test mode indication Test mode set up terminal Not used (Fixed at "H") Test key (4x8 matrix) signal output terminal (OPEN) Test key (4x8 matrix) signal output terminal (OPEN) Test key (4x8 matrix) signal output terminal (OPEN) Test key (4x8 matrix) signal output terminal (OPEN) Test key (4x8 matrix) signal input terminal (Fixed at "L") Test key (4x8 matrix) signal input terminal (Fixed at "L") Test key (4x8 matrix) signal input terminal (Fixed at "L") *2 Loading motor (M903) control
Mode Terminal
BUS ON : "L"
Sub-code Q sync (SCOR) input from CXD2535CR (IC200)
"H" is input when the focus is applied Deemphasis ON "L"
Power ON : "H"
Deemphasis control signal output to the D/A converter (IC550) When mute : "H"
Not used this set (OPEN) Not used this set (OPEN) When test mode : "L"
Normolly :"H"
Power supply terminal (+5V)
*1 Elevator motor (M904) control
Mode Terminal
UP "H" "L"
DOWN "L" "H"
IN "L" "H"
OUT "H" "L"
Brake "H" "H"
M1 pin 6 M1 pin 7
M2 pin 8 M2 pin 9
40
SECTION 4 EXPLODED VIEWS
NOTE: · -XX and -X mean standardized parts, so they may have some difference from the original one. · Color Indication of Appearrance Parts Example: KNOB, BALANCE (WHITE) . . . (RED) Parts Color Cabinet's Color · Items marked "*" are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. · The mechanical parts with no reference number in the exploded views are not supplied. · Hardware (# mark) list and accessories and packing materials are given in the last of the electrical parts list. The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. Les composants identifiés par une marque ! sont critiquens pour la sécurité. Ne les remplacer que par une pièce portant le neméro spécifié.
4-1.
CASE SECTION 8
3
5
MG-798-133
6 19 17
7 3 16 10
9
CNP1
18 15 7 12 1 15
#1
4
not supplied
2 17
11 13
14 12 13
Ref. No. 1 2 3 4 5 * 6 7 * 8 9 10 Part No. X-3371-273-1 3-930-168-11 3-912-956-11 4-969-961-01 X-3373-364-1 1-664-517-11 3-909-607-01 3-930-172-31 3-930-175-11 X-3371-225-1 Description DOOR (S) ASSY(/EXP) DOOR (P) SCREW (2.6X6) (CU), +BVTT EMBLEM (NO.4), SONY PANEL (FRONT) ASSY (/EXP) LAMP BOARD SCREW CASE (UPPER) COVER (CORD) PANEL (REAR) ASSY (/EXP) Remark Ref. No. * 11 12 13 * 14 15 16 17 18 19 CNP1 Part No. A-3294-228-A 3-930-176-01 3-930-177-01 3-930-173-31 3-931-697-01 3-348-750-01 3-930-744-01 3-933-740-01 3-831-441-11 1-776-105-11 Description POWER BOARD, COMPLETE DAMPER (798) SPRING (FL), TENSION CASE (LOWER) CUSHION (STOPPER) CUSHION (DAMPER) SPACER (DOOR) SHEET (SLIDE) CUSHION, RATTLE ABSORBER CORD (WITH CONNECTOR) (BUS CONTROL/ RCA PIN JACK) Remark
41
Ver 1.1
4-2. MECHANISM SECTION-1 (MG-798-133)
58
59
71
57 69 56 55 54
#2 #4
60 60
S902 #4
S903
M903
62 52
#3
61 70 53 52 51 60
#2
67 64
#2 #2
63
M904
68 65
#2 #2
66 52
Ref. No. 51 52 53 * 54 55 56 57 58 59 60 61 62 63
Part No. 3-930-351-01 3-377-719-11 3-880-990-00 A-3294-229-A 1-776-474-11 1-658-887-11 1-658-881-11 3-909-412-01 A-3309-891-A 3-930-312-01
Description WHEEL (ELV), WORM WASHER, POLYETHYLENE SCREW (1.7X3),FLAT,(+) SPECIAL MAIN BOARD, COMPLETE CABLE, FLAT 7P MAIN FLEXIBLE BOARD SERVO FLEXIBLE BOARD SCREW (+P) (1.7X2) (TYPE 3) SENSOR BOARD, COMPLETE BEARING (ELV)
Remark
Ref. No. * 64 65 66 67 68 69 * 70 * 71 M903 M904 S902 S903
Part No. X-3371-218-1 X-3371-211-1 3-930-313-01 3-931-698-01 3-348-750-01 3-931-366-01 3-931-149-02 3-931-025-01 X-3371-508-1 A-3291-505-A
Description CHASSIS (BASE) ASSY CHASSIS (GEAR) ASSY GEAR (ELVC) CUSHION (ROLL L) CUSHION (DAMPER) STOPPER, LEAD SHEET (MAIN PC BOARD) SHEET (MECHANICAL DECK) MOTOR ASSY (LOADING) ELV MOTOR BLOCK ASSY (ELEVATOR)
Remark
X-3371-220-1 BRACKET (LD) ASSY 3-930-365-01 WHEEL (LD), WORM 3-930-317-01 GEAR (LD)
1-570-771-11 SWITCH (LES) 1-570-771-21 SWITCH (SES)
42
4-3. MECHANISM SECTION-2 (MG-798-133) 129 128
#2 #2
127
127 129
#2
112 129 128
(US, Canadian)
110
111
112 130 114 115 116 132 131
not supplied
113 130 109 108 107 106 105 104 126 101 117
118 124 126 120 121 122 119
102 101
103
125
123
125
Ref. No. 101 102 103 104 105 106 107 108 109 110 111 112 * 113 * 114 * 115 * 116
Part No. 3-377-719-11 3-930-354-01 3-930-350-01 3-930-318-51 3-930-318-41 3-930-318-31 3-930-318-21 3-930-318-11 3-930-318-01 3-930-314-01 3-930-319-01 3-930-311-01 3-930-320-01 3-930-316-01 X-3371-209-1
Description WASHER, POLYETHYLENE LEVER, DISK EJECT SPRING (EJ), TORSION BUTTON (EJECT) BUTTON (EJECT) BUTTON (EJECT) BUTTON (EJECT) BUTTON (EJECT) BUTTON (EJECT) ESCUTCHEON BUTTON (STOP) RETAINER (ELV) CHASSIS (FRONT) GUIDE (HOLDER) CHASSIS (TOP) ASSY
Remark
Ref. No. 117 118 * 119 120 121 122 123 124 125 * 126 127 128 129 130 131 132
Part No. 3-930-366-01 3-930-360-01 X-3371-221-1 X-3371-210-3 3-930-349-01 X-3371-219-1 3-331-007-21 3-930-352-01 X-3371-216-1 3-317-054-01 3-931-699-01 9-911-840-XX 3-348-750-01 3-317-552-71 3-891-132-00
Description RACK (LOADING) SPRING (LIMITER), TORSION SLIDER ASSY, LOADING CHASSIS (REAR) ASSY SPRING (LOCK), TORSION PLATE (HOLDER) ASSY, LOCK WASHER SPRING (D LOCK), TENSION HOLDER (CADDIE) ASSY SPACER, E CUSHION (ROLL H) CUSHION CUSHION (DAMPER) SCREW (M1.7) SCREW (M1.7x2.0), SPECIAL HEAD
Remark
3-930-321-01 PLATE, HOLDER STOP
3-935-293-01 SHEET (COPY MD) (US, Canadian)
43
4-4. MECHANISM SECTION-3 (MG-798-133)
#6
#6
#6
158
159
157
157 156 155 160 155 156 155
161 174
RV901
163
162
#6 #2 M901
154
#4
164
S901
165
M902
153
#6 #7
167 166 168
152 171
#2 #5
170
169
151
#5
172 173
The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified.
Les composants identifiés par une marque ! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le neméro spécifié.
Ref. No. 151 152 153 154 155 156 157 * 158 159 160 161 162 163 164
Part No. 3-930-338-01 3-930-332-01 X-3371-212-1 1-658-880-11 3-930-333-01 3-930-334-01 3-930-345-01 X-3371-215-1 3-930-344-01 3-930-711-01 3-930-339-01 3-338-645-31 3-930-343-01 3-930-342-01
Description HOLDER (OP GUIDE B) GUIDE (OPB) SCREW (ELV) ASSY, FEED EHS FLEXIBLE BOARD SLEEVE (ELV) SPRING (ELV), COMPRESSION PLATE (B), ELV LIMITER CHASSIS (OP) ASSY PLATE (A), ELV LIMITER SPRING (ELV2), COMPRESSION WHEEL (SL), WORM WASHER (0.8-2.5) SCREW (K1.7X3.5) RETAINER (SP)
Remark
Ref. No. 165 166 167 168 169 170 ! 171 * 172 173 174 M901 M902 RV901 S901
Part No. 3-930-336-01 3-930-335-01 X-3371-213-1 X-3371-214-1 3-930-331-01 3-930-337-01 8-583-035-01 A-3222-980-A 3-932-755-01 3-930-310-01
Description HOLDER (SLB) DETENT, SL HOLDER (SLA) ASSY SCREW (SL) ASSY, FEED GUIDE (OPA) SPRING (SL OUTSERT), FEED OPTICAL PICK UP KMS-193C/J2N SERVO BOARD, COMPLETE SCREW (M1.7X2.2) COLLAR (EHS)
Remark
A-3291-507-A SP MOTOR BLOCK ASSY (SPINDLE) A-3291-508-A SL MOTOR BLOCK ASSY (SLED) 1-223-817-11 RES, VAR, SLIDE 10K (ELEVATOR HIGHT SENSOR) 1-570-771-21 SWITCH (HOME POSITION DETECT)
44
EHS FLEXIBLE SECTION 5 ELECTRICAL PARTS LIST
NOTE: · Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. · -XX and -X mean standardized parts, so they may have some difference from the original one. · RESISTORS All resistors are in ohms. METAL: Metal-film resistor. METAL OXIDE: Metal oxide-film resistor. F: nonflammable · Items marked "*" are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. · SEMICONDUCTORS In each case, u: µ, for example: uA. . : µA. . uPA. . : µPA. . uPB. . : µPB. . uPC. . : µPC. . uPD. . : µPD. . · CAPACITORS uF: µF · COILS uH: µH
LAMP
MAIN
The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. Les composants identifiés par une marque ! sont critiquens pour la sécurité. Ne les remplacer que par une pièce portant le neméro spécifié. When indicating parts by reference number, please include the board.
Ref. No.
Part No.
Description
Remark
Ref. No. C509 C510 C511 C512 C513 C520 C521 C550 C551 C553 C554 C557 C560 C600 C601 C602 C603 C604 C605 C607 C608 C609 C610 C611 C620 C621 C650 C651 C652 C653 C700 C701
Part No.
Description 0.22uF 0.1uF 100PF 0.22uF 100PF 68PF 10uF 22uF 0.1uF 1000PF 0.22uF 0.1uF 10uF 22uF 0.22uF 0.22uF 0.1uF 0.1uF 0.1uF 100PF 15PF 15PF 0.1uF 0.22uF 0.1uF 0.1uF 0.22uF 0.22uF 0.22uF 0.22uF 0.1uF 0.1uF 10% 5% 5% 5% 20% 20% 10% 5% 10% 20% 20% 10% 10% 10% 10% 5% 5% 5% 10% 10% 10% 16V 16V
Remark
1-658-880-11 EHS FLEXIBLE BOARD ****************** < VARIABLE RESISTOR > RV901 1-223-817-11 RES, VAR, SLIDE 10K (ELEVATOR HIGHT SENSOR) < SWITCH >
1-165-128-11 CERAMIC CHIP 1-107-826-11 CERAMIC CHIP 1-162-927-11 1-165-128-11 1-162-927-11 1-162-925-11 1-135-259-11 1-104-852-11 1-107-826-11 1-164-357-11 1-165-128-11 1-164-004-11 1-135-259-11 1-104-852-11 1-165-128-11 1-164-489-11 1-107-826-11 1-107-826-11 1-107-826-11 1-162-927-11 1-162-917-11 1-162-917-11 1-107-826-11 1-165-128-11 1-107-826-11 1-107-826-11 1-165-128-11 1-165-128-11 1-165-128-11 1-165-128-11 1-107-826-11 1-107-826-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP < CONNECTOR >
50V 16V 50V 50V 6.3V 10V 16V 50V 16V 25V 6.3V 10V 16V 16V 16V 16V 16V 50V 50V 50V 16V 16V 16V 16V 16V 16V 16V 16V 16V 16V
S901 1-570-771-21 SWITCH (HOME POSITION DETECT) ************************************************************* * 1-664-517-11 LAMP BOARD *********** < CONNECTOR > * CN620 1-580-056-21 PIN, CONNECTOR 3P < PILOT LAMP > PL620 1-517-492-11 LAMP, PILOT (ILLUMINATION) < RESISTOR > R620 1-216-298-00 METAL CHIP < SWITCH > 1-692-532-21 SWITCH, PUSH (1 KEY) (DOOR OPEN/CLOSE DET) ************************************************************* * A-3294-229-A MAIN BOARD, COMPLETE ********************* < CAPACITOR > C500 C501 C503 C504 C505 C506 C507 C508 1-165-128-11 1-128-361-11 1-162-970-11 1-162-910-11 1-165-128-11 CERAMIC CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.22uF 470uF 0.01uF 5PF 0.22uF 10uF 0.1uF 0.1uF 16V 20% 10V 10% 25V 0.25PF 50V 16V 20% 10% 10% 6.3V 16V 16V S620 2.2 5% 1/10W
10% 10%
1-135-259-11 TANTAL. CHIP 1-107-826-11 CERAMIC CHIP 1-107-826-11 CERAMIC CHIP
CN500 * CN600 CN601 CN602 CN603
1-573-370-21 1-573-939-11 1-573-916-11 1-580-055-21 1-580-055-21
CONNECTOR, FFC/FPC 30P CONNECTOR, FFC/FPC (ZIF) 30P CONNECTOR, FFC/FPC (ZIF) 7P PIN, CONNECTOR 2P PIN, CONNECTOR 2P
45
MAIN
Ref. No. * CN604 CN700 CN701 Part No. Description Remark Ref. No. R504 R505 R506 R520 R521 R550 R551 R552 R553 R560 R561 R600 R601 R602 R603 R605 R607 R608 R609 R610 R611 R612 R613 R614 R615 R616 R617 R618 R619 R622 R624 R625 R626 R627 R628 R629 R630 R631 R632 R633 R634 R636 Part No. Description 100 51K 39K 150 68 10 100 100 2.2K 1K 10K 47K 100K 100K 100K 100K 4.7K 1K 2.2K 1K 2.2K 100K 1K 2.2K 1K 2.2K 100K 100K 10K 100 1K 100K 100K 1K 100K 100K 47K 1K 1K 1K 10K 0 5% 0.50% 0.50% 5% 0.50% 5% 5% 5% 5% 0.50% 0.50% 5% 5% 5% 5% 5% 0.50% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% Remark 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W
1-580-056-21 PIN, CONNECTOR 3P 1-580-055-21 PIN, CONNECTOR 2P 1-580-055-21 PIN, CONNECTOR 2P < DIODE >
1-216-809-11 METAL CHIP 1-218-733-11 1-218-730-11 1-216-811-11 1-218-664-11 1-216-797-11 1-216-809-11 1-216-809-11 1-216-825-11 1-218-692-11 1-218-716-11 1-216-841-11 1-216-845-11 1-216-845-11 1-216-845-11 1-216-845-11 1-218-708-11 1-216-821-11 1-216-825-11 1-216-821-11 1-216-825-11 1-216-845-11 1-216-821-11 1-216-825-11 1-216-821-11 1-216-825-11 1-216-845-11 1-216-845-11 1-216-833-11 1-216-809-11 1-216-821-11 1-216-845-11 1-216-845-11 1-216-821-11 1-216-845-11 1-216-845-11 1-216-841-11 1-216-821-11 1-216-821-11 1-216-821-11 1-216-833-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
D502 D560 D561 D562 D600
8-719-421-36 8-719-988-62 8-719-988-62 8-719-988-62 8-719-422-64
DIODE DIODE DIODE DIODE DIODE
MA8036-L 1SS355 1SS355 1SS355 MA8062-M
< FERRITE BEAD > FB510 FB650 FB651 1-414-235-11 INDUCTOR, FERRITE BEAD 1-500-235-21 BEAD, FERRITE (CHIP) 1-500-235-21 BEAD, FERRITE (CHIP) < IC > IC500 IC501 IC550 IC600 IC601 IC602 IC700 IC701 8-752-371-17 8-759-341-28 8-759-425-18 8-752-882-94 8-759-363-81 IC IC IC IC IC CXD2536R HM51W4400TT6-8 CS4330-KSR-H CXP84340-043Q XC61AN4002PR
8-759-238-47 IC TC74HCT7007AF(EL) 8-759-823-87 IC LB1638M 8-759-823-87 IC LB1638M < COIL >
L500 L501 L502 L600
1-412-058-11 1-410-998-31 1-412-058-11 1-412-058-11
INDUCTOR CHIP INDUCTOR CHIP INDUCTOR CHIP INDUCTOR CHIP < FILTER >
10uH 2.7uH 10uH 10uH
NF650 NF651
1-239-466-21 FILTER, EMI 1-239-581-21 FILTER, EMI < TRANSISTOR >
Q500 Q501 Q560 Q561 Q600 Q601
8-729-020-67 8-729-920-21 8-729-424-59 8-729-421-22 8-729-904-60
TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
XN1A312-TX DTC314TKH04 UN2212 UN2211 DTB113ZK
8-729-421-22 TRANSISTOR UN2211 < RESISTOR >
1-216-864-11 METAL CHIP
< COMPOSITION CIRCUIT BLOCK > 1K 330 3.3K 100 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W RB600 RB601 RB602 RB603 1-239-517-11 1-239-517-11 1-239-514-11 1-239-516-11 RESISTOR, NETWORK (1608) 100Kx4 RESISTOR, NETWORK (1608) 100Kx4 RESISTOR, NETWORK (1608) 100Kx4 RESISTOR, NETWORK (1608) 1Kx4
R500 R501 R502 R503
1-216-821-11 1-216-815-11 1-216-827-11 1-216-809-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP
46
MAIN
Ref. No. RB604 RB605 RB606 RB607 RB609 Part No. Description Remark Ref. No. C932 C940 C941 C942 C950 C951 C952 C953 C954 C955 C956 C957 C958 C959 C960 C961 C962 C963 C970 Part No. 1-164-004-11 1-164-004-11 1-110-474-11 1-164-004-11 1-163-125-00 1-163-275-11 1-163-263-11 1-163-275-11 1-163-263-11 1-110-456-11 1-128-590-11 1-128-590-11 1-164-004-11 1-110-447-11 1-128-590-11 1-128-590-11 1-164-004-11 1-164-004-11 1-163-275-11 Description CERAMIC CHIP CERAMIC CHIP SOLID CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP SOLID CHIP ELECT CHIP ELECT CHIP CERAMIC CHIP SOLID CHIP ELECT CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP < CONNECTOR > * CN800 CN900 47uF 0.1uF 0.1uF 100uF 3.3uF 100PF 10uF 3.3uF 220PF 220PF 3.3uF 100PF 10uF 3.3uF 220PF 20% 10% 10% 20% 20% 5% 20% 20% 5% 5% 20% 5% 20% 20% 5% 16V 25V 25V 6.3V 25V 50V 50V 25V 50V 50V 25V 50V 50V 25V 50V 50V 50V 25V 50V 16V 16V 25V 25V 5.5V 16V 6.3V 0.1uF 0.1uF 10uF 0.1uF 220PF 0.001uF 330PF 0.001uF 330PF 47uF 100uF 100uF 0.1uF 22uF 100uF 100uF 0.1uF 0.1uF 0.001uF
POWER
Remark 10% 10% 20% 10% 5% 5% 5% 5% 5% 20% 20% 20% 10% 20% 20% 20% 10% 10% 5% 25V 25V 50V 25V 50V 50V 50V 50V 50V 16V 6.3V 6.3V 25V 6.3V 6.3V 6.3V 25V 25V 50V
1-239-516-11 RESISTOR, NETWORK (1608) 1Kx4 1-239-517-11 1-239-516-11 1-239-516-11 1-239-516-11 RESISTOR, NETWORK (1608) 100Kx4 RESISTOR, NETWORK (1608) 1Kx4 RESISTOR, NETWORK (1608) 1Kx4 RESISTOR, NETWORK (1608) 1Kx4 < SWITCH >
S600
1-571-914-21 SWITCH, KEY BOARD (STOP) < THERMISTOR >
TH600
1-810-421-11 THERMISTOR NTH5G36B103K01TE 10K < VIBRATOR >
X500 1-760-168-11 VIBRATOR, CRYSTAL (45.1584MHz) X600 1-760-365-11 VIBRATOR, CERAMIC (10MHz) X601 1-579-886-21 VIBRATOR, CRYSTAL (32.768KHz) ************************************************************* * A-3294-228-A POWER BOARD, COMPLETE *********************** < CAPACITOR > C800 C801 C803 C805 C810 C811 C812 C813 C814 C815 C820 C821 C822 C823 C824 C825 C900 C901 C902 C903 C904 C909 C910 C911 C920 C931 1-110-456-11 1-164-004-11 1-164-004-11 1-110-450-11 1-110-457-11 1-163-251-11 1-110-474-11 1-110-457-11 1-163-125-00 1-163-125-00 1-110-457-11 1-163-251-11 1-110-474-11 1-110-457-11 1-163-125-00 1-163-125-00 1-163-017-00 1-164-004-11 1-163-275-11 1-110-456-11 1-164-505-11 1-164-004-11 1-164-004-11 1-125-710-11 1-164-346-11 SOLID CHIP CERAMIC CHIP CERAMIC CHIP SOLID CHIP SOLID CHIP CERAMIC CHIP SOLID CHIP SOLID CHIP CERAMIC CHIP CERAMIC CHIP SOLID CHIP CERAMIC CHIP SOLID CHIP SOLID CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP SOLID CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CAPACITOR CERAMIC CHIP
1-573-939-11 CONNECTOR, FFC/FPC (ZIF) 30P 1-764-585-11 PIN, CONNECTOR (PC BOARD) 12P < DIODE >
D900 D901 D902 D910 D911 D912 D920 D921 D930 D940 D950 D951 D952
8-719-422-64 8-719-422-64 8-719-975-40 8-719-977-12 8-719-400-20 8-719-988-62 8-719-422-64 8-719-988-62 8-719-422-16 8-719-422-97
DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE
MA8062-M MA8062-M RB411D DTZ6.8B MA152WA 1SS355 MA8062-M 1SS355 MA8039-L-TX MA8091-M
8-719-975-33 DIODE RB110C 8-719-422-16 DIODE MA8039-L-TX 8-719-975-33 DIODE RB110C < FERRITE BEAD >
220PF 5% 0.0047uF 5% 0.1uF 10% 0.001uF 5% 47uF 20% 2.2uF 0.1uF 0.1uF 0.1F 1uF 10uF
FB810 FB820
1-414-598-11 INDUCTOR, FERRITE BEAD 1-414-598-11 INDUCTOR, FERRITE BEAD < IC >
10% 10%
IC800 IC900 IC950
8-759-711-82 IC NJM4580E 8-759-284-87 IC MM1284XFFE 8-759-370-13 IC TL1451ACDB-E20
1-110-446-11 SOLID CHIP
20%
47
Ver 1.1
POWER
Ref. No. Part No.
SENSOR
Description < COIL > Remark Ref. No. R921 R922 10uH 33uH 10uH 33uH 10uH R930 R931 R940 R950 R951 R952 R953 R954 R955 R956 R957 R958 R959 R960 R961 R962 R963 R964 R965 R966 Part No. Description 33K 100K 2.2K 2.2K 1K 10K 4.7K 4.7K 5.6K 15K 15K 33K 33K 33K 33K 100 680 680 10K 3.3K 100 100 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 0.5% 0.5% 5% 5% Remark 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W
1-216-085-00 METAL CHIP 1-216-097-00 METAL GLAZE 1-216-057-00 1-216-057-00 1-216-049-00 1-216-073-00 1-216-065-00 1-216-065-00 1-216-067-00 1-216-077-00 1-216-077-00 1-216-085-00 1-216-085-00 1-216-085-00 1-216-085-00 1-216-025-00 1-216-045-00 1-216-045-00 1-216-675-11 1-216-663-11 1-216-025-00 1-216-025-00 METAL CHIP METAL CHIP METAL GLAZE METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL GLAZE METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL GLAZE METAL GLAZE
L950 L951 L952 L953 L954
1-409-640-21 1-403-584-11 1-409-640-21 1-403-584-11 1-409-640-21
COIL, CHIP CHOKE COIL, CHIP CHOKE COIL, CHIP CHOKE COIL, CHIP CHOKE COIL, CHIP CHOKE < FILTER >
NF900
1-239-466-21 FILTER, EMI < IC LINK >
PS900
1-533-397-11 LINK, CHIP IC (ICB-S2.3) < TRANSISTOR >
Q800 Q810 Q820 Q910 Q911 Q920 Q921 Q931 Q940 Q941 Q950 Q952 Q953 Q954
8-729-424-12 8-729-920-21 8-729-920-21 8-729-920-85 8-729-422-27 8-729-422-27 8-729-424-12 8-729-920-85 8-729-020-67 8-729-920-85 8-729-106-60 8-729-822-84 8-729-920-85 8-729-106-60
TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR < RESISTOR >
UN2112 DTC314TKH04 DTC314TKH04 2SD1664-QR 2SD601A-Q 2SD601A-Q UN2112 2SD1664-QR XN1A312-TX 2SD1664-QR 2SB1115A 2SB1202FAST 2SD1664-QR 2SB1115A
R967 1-216-045-00 METAL CHIP 680 5% 1/10W R968 1-216-045-00 METAL CHIP 680 5% 1/10W R969 1-216-675-11 METAL CHIP 10K 0.5% 1/10W R970 1-216-663-11 METAL CHIP 3.3K 0.5% 1/10W R980 1-216-841-11 METAL CHIP 47K 5% 1/16W ************************************************************* A-3309-891-A SENSOR BOARD, COMPLETE ************************
R800 R801 R811 R812 R813 R814 R815 R816 R821 R822 R823 R824 R825 R826 R900 R910 R911 R920
1-216-057-00 1-216-057-00 1-208-561-11 1-216-238-00 1-208-561-11 1-216-238-00 1-216-182-00 1-216-246-00 1-208-561-11 1-216-238-00 1-208-561-11 1-216-238-00 1-216-182-00 1-216-246-00 1-216-089-00
METAL CHIP METAL CHIP METAL GLAZE METAL GLAZE METAL GLAZE METAL GLAZE METAL GLAZE METAL GLAZE METAL GLAZE METAL GLAZE METAL GLAZE METAL GLAZE METAL GLAZE METAL GLAZE METAL GLAZE
2.2K 2.2K 27K 47K 27K 47K 220 100K 27K 47K 27K 47K 220 100K 47K 22K 1K 47K
5% 5% 2% 2% 2% 2% 2% 2% 2% 2% 2% 2% 2% 2% 5% 5% 5% 5%
1/10W 1/10W 1/8W 1/8W 1/8W 1/8W 1/8W 1/8W 1/8W 1/8W 1/8W 1/8W 1/8W 1/8W 1/10W 1/10W 1/10W 1/10W
For the parts on the SENSOR board, replace the entire mounted board. *************************************************************
1-216-081-00 METAL CHIP 1-216-049-00 METAL GLAZE 1-216-089-00 METAL GLAZE
48
SERVO
Ref. No. * Part No. Description Remark Ref. No. Part No. Description < IC > IC100 IC200 IC201 IC300 8-752-072-68 8-752-382-23 8-759-031-84 8-759-442-80 IC IC IC IC CXA1981AR CXD2535CR-1 SC7S04F MPC17A38ZVMEL Remark
A-3222-980-A SERVO BOARD, COMPLETE ********************* < CAPACITOR > C102 C103 C104 C105 C106 C107 C108 C111 C113 C114 C115 C117 C118 C119 C120 C123 C200 C202 C204 C205 C206 C207 C208 C209 C210 C211 C301 C302 C303 C304 C305 C306 C307 1-135-259-11 1-135-259-11 1-162-964-11 1-162-969-11 1-164-227-11 1-162-970-11 1-162-970-11 1-104-852-11 1-107-826-11 1-162-970-11 1-109-982-11 1-109-982-11 1-162-968-11 1-162-969-11 1-165-176-11 1-107-826-11 1-109-982-11 1-135-259-11 1-162-970-11 1-107-823-11 1-162-927-11 1-162-979-11 1-162-587-11 1-107-826-11 1-107-826-11 1-107-826-11 1-109-982-11 1-109-982-11 1-104-852-11 1-109-982-11 TANTAL. CHIP TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP 10uF 20% 10uF 20% 0.001uF 10% 0.0068uF 10% 0.022uF 10% 0.01uF 0.01uF 22uF 0.1uF 0.01uF 10% 10% 20% 10% 10% 6.3V 6.3V 50V 25V 25V 25V 25V 6.3V 16V 25V 10V 10V 50V 25V 16V 16V 10V 6.3V 25V 16V 50V 50V 25V 16V 16V 16V 10V 10V 10V 10V 10V 16V 16V
< COIL > L100 L200 L300 L301 L302 L303 L304 1-412-058-11 1-412-058-11 1-412-637-51 1-412-039-51 1-412-039-51 INDUCTOR CHIP 10uH INDUCTOR CHIP 10uH INDUCTOR 330uH INDUCTOR CHIP 100uH INDUCTOR CHIP 100uH
1-412-039-51 INDUCTOR CHIP 100uH 1-412-039-51 INDUCTOR CHIP 100uH < TRANSISTOR >
1uF 10% 1uF 10% 0.0047uF 10% 0.0068uF 10% 0.047uF 10% 0.1uF 1uF 10uF 0.01uF 0.47uF 10% 10% 20% 10% 10%
Q100 Q200
8-729-216-22 TRANSISTOR 2SA1162-G 8-729-422-27 TRANSISTOR 2SD601A-Q < RESISTOR >
100PF 5% 0.0027uF 10% 0.039uF 10% 0.1uF 10% 0.1uF 10% 0.1uF 1uF 1uF 22uF 1uF 1uF 1uF 0.1uF 10% 10% 10% 20% 10% 10% 10% 10%
R100 R101 R102 R103 R104 R106 R107 R108 R109 R110 R111 R201 R202 R203 R207 R208 R209 R210 R211 R212 R221 R222 R223 R224
1-216-841-11 1-216-308-00 1-216-811-11 1-216-853-11 1-216-829-11 1-216-853-11 1-216-825-11 1-216-825-11 1-216-825-11 1-216-835-11 1-216-841-11 1-216-809-11 1-216-809-11 1-216-809-11 1-216-833-11 1-216-845-11 1-216-857-11 1-216-827-11 1-218-270-11 1-216-822-11 1-216-853-11 1-216-819-11 1-216-821-11 1-216-821-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL GLAZE METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
47K 4.7 150 470K 4.7K 470K 2.2K 2.2K 2.2K 15K 47K 100 100 100 10K 100K 1M 3.3K 1.1K 1.2K 470K 680 1K 1K
5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5%
1/16W 1/10W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W
1-109-982-11 CERAMIC CHIP 1-107-682-11 CERAMIC CHIP 1-107-826-11 CERAMIC CHIP < CONNECTOR >
CN100 CN200 CN301 CN400
1-573-931-11 1-573-370-21 1-580-055-21 1-573-346-21
CONNECTOR, FFC/FPC (ZIF) 22P CONNECTOR, FFC/FPC 30P PIN, CONNECTOR 2P CONNECTOR, FFC/FPC 6P < DIODE >
D300 D301
8-719-988-62 DIODE 1SS355 8-719-988-62 DIODE 1SS355 RB201 RB202
< COMPOSITION CIRCUIT BLOCK > 1-233-576-11 RES, CHIP NETWORK 100x4 1-233-576-11 RES, CHIP NETWORK 100x4
49
MDX-61 SERVO
Ref. No. RB203 Part No. Description Remark Ref. No. Part No. Description MOUNTING HARDWARE ******************* 501 502 503 504 506 509 510 3-930-163-01 X-3371-178-1 7-682-961-01 4-304-511-00 3-930-166-01 BASE (FITTING) BRACKET ASSY SCREW +PSW 4X8 NUT (M5), FLANGE CUSHION (FITTING) Remark
1-233-576-11 RES, CHIP NETWORK 100x4 < SWITCH >
S400 1-692-532-21 SWITCH, PUSH (1 KEY) (LIMIT DET) ************************************************************* MISCELLANEOUS ************** 55 56 57 154 ! 171 CNP1 M901 M902 M903 M904 RV901 1-776-474-11 1-658-887-11 1-658-881-11 1-658-880-11 8-583-035-01 CABLE, FLAT 7P MAIN FLEXIBLE BOARD SERVO FLEXIBLE BOARD EHS FLEXIBLE BOARD OPTICAL PICK UP KMS-193C/J2N
1-590-519-21 CORD (WITH CONNECTOR) (BUS CABLE 5.5m) 1-777-284-11 CORD, CONNECTION (RCA PIN CORD 5.5m)
1-776-105-11 CORD (WITH CONNECTOR) (BUS CONTROL/RCA PIN JACK) A-3291-507-A SP MOTOR BLOCK ASSY (SPINDLE) A-3291-508-A SL MOTOR BLOCK ASSY (SLED) X-3371-508-1 MOTOR ASSY (LOADING) A-3291-505-A ELV MOTOR BLOCK ASSY (ELEVATOR)
1-223-817-11 RES, VAR, SLIDE 10K (ELEVATOR HIGHT SENSOR) S901 1-570-771-21 SWITCH (HOME POSITION DETECT) S902 1-570-771-11 SWITCH (LES) S903 1-570-771-21 SWITCH (SES) ************************************************************* ************** HARDWARE LIST ************** #1 #2 #3 #4 #5 7-685-793-09 7-627-852-37 7-627-554-07 7-627-855-07 7-627-852-27 SCREW +PTT 2.6X8 (S) PRECISION SCREW +P 1.7X1.8 TYPE3 SCREW,PRECISION +P 2X2.2 SCREW,PRECISION +P 2X5.5 TYPE3 +P 1.7X3
#6 7-627-552-18 SCREW,PRECISION +P 1.7X1.6 #7 7-627-852-58 SCREW,PRECISION +P 1.7X5 TYPE3 ************************************************************* ACCESSORIES & PACKING MATERIALS ******************************** 3-859-134-11 MANUAL, INSTRUCTION (ENGLISH,FRENCH, GERMAN,ITALIAN) (AEP,UK,German) 3-859-134-21 MANUAL, INSTRUCTION (DUTCH,SWEDISH, PORTUGUESE,SPANISH) (AEP,UK) 3-859-134-31 MANUAL, INSTRUCTION (ENGLISH,FRENCH, SPANISH,CHINESE) (US,Canadian,E) *************************************************************
The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified.
Les composants identifiés par une marque ! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le neméro spécifié.
50
MDX-61
MEMO
51
MDX-61
REVISION HISTORY
Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. 1.1 1.0 Date 2001.08 1998.01 1997.01 Description of Revision Correction-1 is included. Correction-1 New