Text preview for : sony_MDS-S40_service_manual.pdf part of Sony MDS-S40 MDS-S40 MINIDISC DECK,self diagnosis,dolby - - Service Manual



Back to : sony_MDS-S40_service_manu | Home

MDS-S40
SERVICE MANUAL
Ver 1.1 2001.03

US Model Canadian Model AEP Model UK Model E Model Australian Model

Photo: Silver model

U.S. and foreign patents licensed form Dolby Laboratories Licensing Corporation.

Model Name Using Similar Mechanism MD Mechanism Type Optical Pick-up Type

MDS-JE520 MDM-5A KMS-260A/J1N

SPECIFICATIONS

­ Continued on next page ­

MINIDISC DECK
9-928-838-12
2001C0500-1 C 2001.3

Sony Corporation
Audio Entertainment Group General Engineering Dept.

· Audio connecting cords (2) · Optical cable (1) · Remote commander (remote) RM-D29M (1) · R6 (size-AA) batteries (2)

SELF-DIAGNOSIS FUNCTION
The self-diagnosis function consists of error codes for customers which are displayed automatically when errors occur, and error codes which show the error history in the test mode during servicing. For details on how to view error codes for the customer, refer to the following box in the instruction manual. For details on how to check error codes during servicing, refer to the following "Procedure for using the Self-Diagnosis Function (Error History Display Mode)".

PROCEDURE FOR USING THE SELF-DIAGNOSIS FUNCTION (ERROR HISTORY DISPLAY MODE)
Note: Perform the self-diagnosis function in the "error history display mode" in the test mode. The following describes the least required procedure. Be careful not to enter other modes by mistake. If you set other modes accidentally, press the MENU/NO button to exit the mode.

1. While pressing the = ~ + knob and p button, connect the power plug to the outlet, and release the = ~ + knob and p button. 2. Turn the = ~ + knob and when "[Service]" is displayed, press the [YES] button. 3. Turn the = ~ + knob to display "ERR DP MODE". 4. Press the [YES] button to sets the error history mode and displays "total rec". 5. Select the contents to be displayed or executed using the = ~ + knob. 6. Press the = ~ + knob to display or execute the contents selected. 7. Press the = ~ + knob another time returns to step 4. 8. Press the [MENU/NO] button to display "ERROR DP MODE" and exits the error history mode. 9. To exit the test mode, press the [REPEAT] button. The unit sets into the STANDBY state, the disc is ejected, and the test mode ends.

­2­

Items of Error History Mode Items and Contents
Selecting the Test Mode Display total rec Details of History Displays the recording time. Displayed as "rh". The displayed time is the total time the laser is set to the high power state. This is about 1/4 of the actual recording time. The time is displayed in decimal digits from 0h to 65535h. Displays the play time. Displayed as "ph". The time displayed is the total actual play time. Pauses are not counted. The time is displayed in decimal digits from 0h to 65535h. Displays the total number of retries during recording and number of retry errors during play. Displayed as "r p". "r" indicates the retries during recording while "p" indicates the retry errors during play. The number of retries and retry errors are displayed in hexadecimal digits from 00 to FF. Displays the total number of errors. Displayed as "total ". The number of errors is displayed in hexadecimal digits from 00 to FF. Displays the 10 latest errors. Displayed as "0 E@@". indicates the history number. The smaller the number, the more recent is the error. (00 is the latest). @@ indicates the error code. Refer to the following table for the details. The error history can be switched by turning the = ~ + knob. Mode which erases the "retry err", "total err", and "err history" histories. When returning the unit to the customer after completing repairs, perform this to erase the past error history. After pressing the = ~ + button and "er refresh?" is displayed, press the [YES] button to erase the history. "Complete!" will be displayed momentarily. Be sure to check the following when this mode has been executed. · The data has been erased. · The mechanism operates normally when recording and play are performed. Mode which erases the "total rec" and "total play" histories. These histories serve as approximate indications of when to replace the optical pickup. If the optical pickup has been replaced, perform this operation and erase the history. After pressing the = ~ + button and "tm refresh?" is displayed, press the [YES] button to erase the history. "Complete!" will be displayed momentarily. Be sure to check the following when this mode has been executed. · The data has been erased. · The mechanism operates normally when recording and play are performed.

total play

retry err

total err

err history

er refresh

tm refresh

Table of Error Codes Error Code E00 E01 Details of Error No error Disc error. PTOC cannot be read (DISC ejected) E02 Disc error. UTOC error (DISC not ejected) E03 E04 Loading error Address cannot be read (Servo has deviated) E0A Error Code E05 E06 E07 E08 E09 Details of Error FOK has deviated Cannot focus (Servo has deviated) Recording retry Recording retry error Playback retry error (Access error) Playback retry error (C2 error)

­3­

SECTION 1 SERVICING NOTES
TABLE OF CONTENTS SELF-DIAGNOSIS FUNCTION .................................... 2 1. 2. 3. 4. 5. 6.
6-1. 6-2. 6-3. 6-4. 6-5. 6-6. 6-7. 6-8. 6-9. 6-10. 6-11. 6-12. 6-13. 6-14. 6-15. SAFETY CHECK-OUT After correcting the original service problem, perform the following safety check before releasing the set to the customer: Check the antenna terminals, metal trim, "metallized" knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. LEAKAGE TEST The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microampers.). Leakage current can be measured by any one of three methods. 1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers' instructions to use these instruments. 2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The "limit" indication is 0.75 V, so analog meters must have an accurate lowvoltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2 V AC range are suitable. (See Fig. A)
To Exposed Metal Parts on Set

SERVICING NOTES ............................................... 4 GENERAL ................................................................... 11 DISASSEMBLY ......................................................... 12 TEST MODE .............................................................. 16 ELECTRICAL ADJUSTMENTS ......................... 21 DIAGRAMS
IC Pin Function Description ........................................... Block Diagram ­ SERVO Section ­ ............................... Block Diagram ­ MAIN Section ­ ................................. Note for Printed Wiring Boards and Schematic Diagrams ....................................................... Printed Wiring Board ­ BD Board ­ ............................. Schematic Diagram ­ BD Board (1/2) ­ ........................ Schematic Diagram ­ BD Board (2/2) ­ ........................ Schematic Diagram ­ SW Board ­ ................................. Printed Wiring Board ­ SW Board ­ .............................. Printed Wiring Boards ­ PT/VOL SEL Boards ­ ........... Printed Wiring Board ­ MAIN Board ­ ......................... Schematic Diagram ­ MAIN Board (1/2) ­ ................... Schematic Diagram ­ MAIN Board (2/2), PT/VOL SEL Boards ­ .............. Printed Wiring Board ­ PANEL Board ­ ....................... Schematic Diagram ­ PANEL Board ­ .......................... 30 37 39 42 43 45 47 49 49 53 55 57 59 61 63

0.15 µF

1.5 k

AC voltmeter (0.75 V)

7. 8.

EXPLODED VIEWS ................................................ 66 ELECTRICAL PARTS LIST ............................... 70
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.

MODEL IDENTIFICATION
-- BACK PANEL -- Part No.

MODEL US model Canadian model AEP, UK, Argentine models Singapore model Hong Kong model Australian model

Part No. 4-216-765-1 4-216-765-2 4-216-765-3 4-216-765-4 4-216-765-5 4-216-765-6

­4­

CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer's instructions. ADVARSEL! Lithiumbatteri-Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandøren.

Laser component in this product is capable of emitting radiation exceeding the limit for Class 1. This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior. This caution label is located inside the unit.

ADVARSEL Eksplosjonsfare ved feilaktig skifte av batteri. Benytt samme batteritype eller en tilsvarende type anbefalt av apparatfabrikanten. Brukte batterier kasseres i henhold til fabrikantens instruksjoner. VARNING Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller en likvärdig typ som rekommenderas av apparattillverkaren. Kassera använt batteri enligt gällande föreskrifter. VAROITUS Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden mukaisesti.

CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Flexible Circuit Board Repairing · Keep the temperature of the soldering iron around 270 °C during repairing. · Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). · Be careful not to apply force on the conductor when soldering or unsoldering. Notes on chip component replacement · Never reuse a disconnected chip component. · Notice that the minus side of a tantalum capacitor may be damaged by heat.

SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE ! SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.

­5­

JIG FOR CHECKING BD BOARD WAVEFORM
The special jig (J-2501-149-A) is useful for checking the waveform of the BD board. The names of terminals and the checking items to be performed are shown as follows. GND : Ground I+3V : For measuring IOP (Check the deterioration of the optical pick-up laser) IOP : For measuring IOP (Check the deterioration of the optical pick-up laser) TEO : TRK error signal (Traverse adjustment) VC : Reference level for checking the signal RF : RF signal (Check jitter)

Mechanism deck

CN110 6P connector

5P Connector

RF

VC TEO IOP I+3V GND

RF VC TEO IOP I+3V GND

for MDM-3 1 RF VC TEO IOP 5 I+3V for MDM-5 1 VC RF TEO IOP I+3V 6 GND

­6­

IOP DATA RECORDING AND DISPLAY WHEN OPTICAL PICK-UP AND NON-VOLATILE MEMORY (IC171 OF BD BOARD) ARE REPLACED
The IOP value labeled on the optical pick-up can be recorded in the non-volatile memory. By recording the value, it will eliminate the need to look at the value on the label of the optical pick-up. When replacing the optical pick-up or non-volatile memory (IC171 of BD board), record the IOP value on the optical pick-up according to the following procedure. Record Precedure: 1. While pressing the = ~ + knob and p button, connect the power plug to the outlet, and release the = ~ + knob and p button. 2. Turn the = ~ + knob to display "[Service]", and press the [YES] button. 3. Turn the = ~ + knob to display "lop Write" (C28), and press the [YES] button. 4. The display becomes "Ref=@@@.@" (@ is an arbitrary number) and the numbers which can be changed will blink. 5. Input the IOP value written on the optical pick-up. To select the number : Turn the = ~ + knob. To select the digit : Press the = ~ + knob. 6. When the [YES] button is pressed, the display becomes "Measu=@@@.@" (@ is an arbitrary number). 7. As the adjustment results are recorded for the 6 value. Leave it as it is and press the [YES] button. 8. "Complete!" will be displayed momentarily. The value will be recorded in the non-volatile memory and the display will become "Iop Write". 9. Press the [REPEAT] button to complete. Display Precedure: 1. While pressing the = ~ + knob and p button, connect the power plug to the outlet, and release the = ~ + knob and p button. 2. Turn th = ~ + knob to display "[Service]", and press the [YES] button. 3. Turn the = ~ + knob to display "lop Read" (C27). 4. "@@.@/##.#" is displayed and the recorded contents are displayed. @@.@ : indicates the IOP value labeled on the optical pick-up. ##.# : indicates the IOP value after adjustment 5. To end, press the = ~ + knod or [MENU/NO] button to display "Iop Read". Then press the [REPEAT] button.

­7­

CHECKS PRIOR TO PARTS REPLACEMENT AND ADJUSTMENTS
Before performing repairs, perform the following checks to determine the faulty locations up to a certain extent. Details of the procedures are described in "5 Electrical Adjustments". Criteria for Determination (Unsatisfactory if specified value is not satisfied) Laser power check (6-2 : See page 23) · 0.9 mW power Specified value : 0.84 to 0.92 mW · 7.0 mW power Specified value : 6.8 to 7.2 mW lop (at 7mW) · Labeled on the optical pickup Iop value ± 10mA Traverse check (6-3 : See page 23) Focus bias check (6-4 : See page 24) · Traverse waveform Specified value : Below 10% offset · Error rate check Specified value : For points a, b, and c C1 error : About 200 AD error : Above 00 · Error rate check Specified value: a. When using test disc (MDW-74/AU-1) C1 error : Below 80 AD error : Below 2 b. When using check disc (TDYS-1) C1 error : Below 50 · CPLAY error rate check Specified value: C1 error : Below 80 AD error : Below 2 Measure if unsatisfactory: · Clean the optical pick-up · Adjust again · Replace the optical pick-up · Replace the optical pick-up

· Replace the optical pick-up · Replace the optical pick-up

C PLAY check (6-5 : See page 24)

· Replace the optical pick-up

Self-recording/playback check (6-6 : See page 24)

If always unsatisfactory: · Replace the overwrite head · Check for disconnection of the circuits around the overwrite head If occasionally unsatisfactory: · Check if the overwrite head is distorted · Check the mechanism around the sled

Temperature compensation offset check (6-1 : See page 23)

· Unsatisfactory if displayed as T=@@ (##) [NG" NG (@@, ## are both arbitrary numbers)

· Check for disconnection of the circuits around D101 (BD board) · Check the signals around IC101, IC121, CN102, CN103 (BD board)

Note: The criteria for determination above is intended merely to determine if satisfactory or not, and does not serve as the specified value for adjustments. When performing adjustments, use the specified values for adjustments.

­8­

RETRY CAUSE DISPLAY MODE
· In this test mode, the causes for retry of the unit during recording can be displayed on the fluorescent indicator tube. During playback, the "track mode" for obtaining track information will be set. This is useful for locating the faulty part of the unit. · The following will be displayed : During recording and stop : Retry cause, number of retries, and number of retry errors. During playback : Information such as type of disc played, part played, copyright. These are displayed in hexadecimal. Precedure: 1. Load a recordable disc whose contents can be erased into the unit. 2. Press the [MENU/NO] button. When "Edit Menu" is displayed on the fluorescent indicator tube, turn the = ~ + knob to display "All Erase?". 3. Press the [YES] button. (Or press the = ~ + knob) 4. When "All Erase??" is displayed on the fluorescent indicator tube, the music calendar number blinks. 5. Press the [YES] button to display "Complete!!", and press the p button immediately. Wait for about 15 seconds while pressing the button. (The = ~ + knob can be pressed instead of the [YES] button for the same results.) 6. When the "TOC" displayed on the fluorescent display tube goes off, release the p button. r 7. Press the [ REC] button to start recording. Then press the P button and start recording. 8. To check the "track mode", press the ( button to start play. 9. To exit the test mode, press the [ ] button, and turn OFF the power. When "TOC" disappears, disconnect the power plug from the 1/u outlet.

Fig. 1 Reading the Test Mode Display (During recording and stop)
RTs@@c##e** Fluorescent display tube display @@ : Cause of retry ## : Number of retries ** : Number of retry errors

Fig. 2 Reading the Test Mode Display (During playback)
@@####**$$ Fluorescent display tube display @@ : ## : ** : $$ : Parts No. (name of area named on TOC) Cluster Sector Address Track mode (Track information such as copyright information of each part)

Reading the Retry Cause Display Hexa1 decimal b7 b6 b5 b4 b3 b2 b1 b0 4 0 0 0 0 0 0 1 0 2 0 0 0 0 0 1 0 0 1 0 0 0 0 1 0 0 0 8 0 0 0 1 0 0 0 0 4 0 0 1 0 0 0 0 0 2 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 0 0 0 0 0 0 0 01 02 04 08 10 20 40 80 Higher Bits Lower Bits Cause of Retry shock ader5 Occurring conditions When track jump (shock) is detected When ADER was counted more than five times continuously

Hexadecimal 8 Bit Binary

Discontinuous address When ADIP address is not continuous When DIN unlock is detected DIN unlock FCS incorrect IVR rec error CLV unlock Access fault When not in focus When ABCD signal level exceeds the specified range When CLV is unlocked When access operation is not performed normally

Reading the Display: Convert the hexadecimal display into binary display. If more than two causes, they will be added. Example When 42 is displayed: Higher bit: 4 = 0100 n b6 Lower bit : 2 = 0010 n b1 In this case, the retry cause is combined of "CLV unlock" and "ader5". When A2 is displayed: Higher bit: A = 1010 n b7+b5 Lower bit : 2 = 0010 n b1 The retry cause in this case is combined of "access fault", "IVR rec error", and "ader5".

­9­

Reading the Retry Cause Display Higher Bits Lower Bits HexaHexadecimal 8 4 2 1 8 4 2 1 decimal Bit b7 b6 b5 b4 b3 b2 b1 b0 Binary 0 0 0 0 0 0 0 1 0 0 0 0 0 0 1 0 0 0 0 0 0 1 0 0 0 0 0 0 1 0 0 0 0 0 0 1 0 0 0 0 0 0 1 0 0 0 0 0 0 1 0 0 0 0 0 0 1 0 0 0 0 0 0 0 01 02 04 08 10 20 40 80 Monaural This is 2-bit display. Normally 01. 01:Normal audio. Others:Invalid Audio (Normal) Original Copyright Write prohibited Invalid Digital copy No copyright Write allowed Details When 0 Emphasis OFF Stereo When 1 Emphasis ON

Reading the Display: Convert the hexadecimal display into binary display. If more than two causes, they will be added. Example When 84 is displayed: Higher bit : 8 = 1000 n b7 Lower bit : 4 = 0100 n b2 In this case, as b2 and b7 are 1 and others are 0, it can be determined that the retry cause is combined of "emphasis OFF", "monaural", "original", "copyright exists", and "write allowed". Example When 07 is displayed: Higher bit : 0 = 1000 n All 0 Lower bit : 7 = 0111 n b0+b1+b2 In this case, as b0, b1, and b2 are 1 and others are 0, it can be determined that the retry cause is combined of "emphasis ON", "stereo", "original", "copyright exists", and "write prohibited".

Hexadecimal n Binary Conversion Table
Hexadecimal 0 1 2 3 4 5 6 7 Binary 0000 0001 0010 0011 0100 0101 0110 0111 Hexadecimal 8 9 A B C D E F Binary 1000 1001 1010 1011 1100 1101 1110 1111

­ 10 ­

SECTION 2 GENERAL

This section is extracted from instruction manual.

­ 11 ­

SECTION 3 DISASSEMBLY
Note: Follow the disassembly procedure in the numerical order given.

COVER
2 cover

1 two screws (CASE 3 TP2)

1 two screws (CASE 3 TP2)

FRONT PANEL SECTION
3 three claws 1 wire (flat type) (21 core) (PANEL-MAIN) (CN421)

4 front panel section

2 three screws (BVTP3 × 10)

2 screw (BVTT3 × 6)

­ 12 ­

MAIN/PT BOARD
1 power cord connector (CN901) 1 connector (CN912)

2 six screws (PTTWH3 × 6)

4 connector (CN502) 5 wire (flat type) (21 core) (BD-MAIN) (CN411) 5 wire (flat type) (21 core) (PANEL-MAIN) (CN421) 5 wire (flat type) (23 core) (CN501)

3 PT board

1 connector (CN921)

6 five screws (BVTP3 × 10)

6 two screws (BVTP3 × 10)

7 MAIN board

MECHANISM DECK SECTION (MDM-5A)
3 four step screws (BVTTWH M3) 1 connector (CN502) 2 wire (flat type) (21 core) (DD-MAIN) (CN411) 4 Remove the mechanism deck (MDM-5A) to direction of the arrow. 2 wire (flat type) (23 core) (CN501)

­ 13 ­

SLIDER (CAM)
7 slider (Cam)

· Note for Installation of Slider A (Cam)

3 bracket (Guide L)

Set the shaft of Cam gear to be at the position in the figure.

1 two screws (P2.6 × 6)

4 harnes

Set the shaft of Lever (O/C) to be at the position in the figure.
4 leaf spring 5 two screws (P2.6 × 6)

6 bracket (Guide R)

BASE UNIT (MBU-5A), BD BOARD

2 base unit (MBU-5A) 5 flexible board (CN104)

6 flexible board (CN101) 1 three screws (P2.6 × 6)

7 BD board 4 screw (M1.7 × 4)

3 Remove the solder (Seven portion).

­ 14 ­

SW BOARD, LOADING MOTOR (M103)
1 screw (PTPWH M2.6 × 6) 2 gear (B) 3 two screws (PWH1.7 × 4)

4 loading motor (M103)

6 SW board

5 three screws (BTP2.6 × 6)

­ 15 ­

SECTION 4 TEST MODE
1. PRECAUTIONS FOR USE OF TEST MODE
· As loading related operations will be performed regardless of the test mode operations being performed, be sure to check that the disc is stopped before setting and removing it. Even if the [ EJECT] button is pressed while the disc is rotating during continuous playback, continuous recording, etc., the disc will 6 not stop rotating. Therefore, it will be ejected while rotating. Be sure to press the [ EJECT] button after pressing the [MENU/NO] button and the rotation of disc is stopped. 6 1-1. Recording laser emission mode and operating buttons · Continuous recording mode (CREC MODE) · Laser power check mode (LDPWR CHECK) · Laser power adjustment mode (LDPWR ADJUST) · Traverse (MO) check (EF MO CHECK) · Traverse (MO) adjustment (EF MO ADJUST) r · When pressing the [ REC] button.

2. SETTING THE TEST MODE
The following are two methods of entering the test mode. Procedure 1: While pressing the = ~ + knob and p button, connect the power plug to an outlet, and release the = ~ + knob and p button. When the test mode is set, "[Check]" will be displayed. Turn the = ~ + knob switches between the following four groups; ···N [Check] N [Adjust] N [Service] N [Develop] N ···. n n n n n Procedure 2: While pressing the = ~ + knob, connect the power plug to the outlet and release the = ~ + knob. When the test mode is set, "TEMP CHECK" will be displayed. By setting the test mode using this method, only the "Check" group of method 1 can be executed.

3. EXITING THE TEST MODE Press the [REPEAT] button. The disc is ejected when loaded, and "Standby" display blinks, and the STANDBY state is set. 4. BASIC OPERATIONS OF THE TEST MODE
All operations are performed using the = ~ + knob, [YES] button, and [MENU/NO] button. The functions of these buttons are as follows.
Function name = ~ + knob YES button MENU/NO button Function Changes parameters and modes Proceeds onto the next step. Finalizes input. Returns to previous step. Stops operations.

­ 16 ­

5. SELECTING THE TEST MODE
There are 31 types of test modes as shown below. The groups can be switched by turn the = ~ + knob. After selecting the group to be used, press the [YES] button. After setting a certain group, turn the = ~ + knob switches between these modes. Refer to "Group" in the table for details selected. All items used for servicing can be treated using group S. So be carefully not to enter other groups by mistake.
Display TEMP CHECK LDPWR CHECK EF MO CHECK EF CD CHECK FBIAS CHECK ScurveCHECK VERIFYMODE DETRK CHECK TEMP ADJUST LDPWR ADJUST EF MO ADJUST EF CD ADJUST FBIAS ADJUST EEP MODE Impossible Impossible ERR DP MODE Impossible Impossible Impossible Impossible Impossible Impossible ADJ CLEAR AG Set (MO) AG Set (CD) Iop Read Iop Write S40 ****** CPLAY MODE CREC MODE No. C01 C02 C03 C04 C05 C06 C07 C08 C09 C10 C11 C12 C13 C14 C15 C16 C17 C18 C19 C20 C21 C22 C23 C24 C25 C26 C27 C28 C29 C30 C31 Laser power check Traverse (MO) check Traverse (CD) check Focus bias check S letter check Non-volatile memory check Detrack check Temperature compensation offset adjustment Laser power adjustment Traverse (MO) adjustment Traverse (CD) adjustment Focus bias adjustment Non-volatile memory control Command transmission Status display Error history display, clear Sled check Access check Outermost circumference check Head position check Same functions as CPLAY MODE Same functions as CREC MODE Initialization of non-volatile memory of adjustment value Auto gain output level adjustment (MO) Auto gain output level adjustment (CD) IOP data display IOP data write Microprocessing version display Continuous play mode Continuous recording mode C C C A A C A (X) (X) (X) (X) (X) (X) A A A S S S S S S S S D D (X) (!) (X) (X) S D D D D D D (X) (X) (X) Contents Temperature compensation offset check Mark C C C C C C C C A A A A A S S S S S D D D Group (*) S S S S S

Group (*) C: Check S: Service

A: Adjust D: Develop

· For details of each adjustment mode, refer to "5. Electrical Adjustments". For details of "ERR DP MODE", refer to "Self-Diagnosis Function" on page 2. · If a different mode has been selected by mistake, press the [MENU/NO] button to exit that mode. · Modes with (X) in the Mark column are not used for servicing and therefore are not described in detail. If these modes are set accidentally, press the [MENU/NO] button to exit the mode immediately. Be especially careful not to set the modes with (!) as they will overwrite the non-volatile memory and reset it, and as a result, the unit will not operate normally.

­ 17 ­

5-1. Operating the Continuous Playback Mode 1. Entering the continuous playback mode (1) Set the disc in the unit. (Whichever recordable discs or discs for playback only are available) (2) Turn the = ~ + knob and display "CPLAY MODE" (C30). (3) Press the [YES] button to change the display to "CPLAY MID". (4) When access completes, the display changes to "C1 = AD = ".
Note: The numbers " " displayed show you error rates and ADER.

2. Changing the parts to be played back (1) Press the [YES] button during continuous playback to change the display as below. "CPLAY MID" n "CPLAY OUT" n "CPLAY IN" When pressed another time, the parts to be played back can be moved. When access completes, the display changes to "C1 = AD = ".
Note: The numbers " " displayed show you error rates and ADER.

(2)

3. Ending the continuous playback mode (1) Press the [MENU/NO] button. The display will change to "CPLAY MODE". 6 (2) Press the [ EJECT] button to remove the disc.
Note: The playback start addresses for IN, MID, and OUT are as follows.

IN MID OUT

40h cluster 300h cluster 700h cluster

5-2. Operating the Continuous Recording Mode (Use only when performing self-recording/palyback check) 1. Entering the continuous recording mode (1) Set a recordable disc in the unit. (2) Turn the = ~ + knob and display "CREC MODE". (3) Press the [YES] button to change the display to "CREC MID" (C31). " and REC lights up. (4) When access completes, the display changes to "CREC (
Note: The numbers " " displayed shows you the recording position addresses.

2. Changing the parts to be recorded (1) When the [YES] button is pressed during continuous recording, the display changes as below. "CREC MID" n "CREC OUT" n "CREC IN" When pressed another time, the parts to be recorded can be changed. REC goes off. " and REC lights up. When access completes, the display changes to "CREC (
Note: The numbers " " displayed shows you the recording position addresses.

(2)

3. Ending the continuous recording mode (1) Press the [MENU/NO] button. The display changes to "CREC MODE" and REC goes off. 6 (2) Press the [ EJECT] button to remove the disc.
Note 1: The recording start addresses for IN, MID, and OUT are as follows.

40h cluster 300h cluster 700h cluster Note 2: The [MENU/NO] button can be used to stop recording anytime.
Note 3: Do not perform continuous recording for long periods of time above 5 minutes. Note 4: During continuous recording, be careful not to apply vibration.

IN MID OUT

5-3. Non-Volatile Memory Mode (EEP MODE) This mode reads and writes the contents of the non-volatile memory. It is not used in servicing. If set accidentally, press the [MENU/NO] button immediately to exit it.

­ 18 ­

6. FUNCTIONS OF OTHER BUTTONS
Function ( p ) 0 SCROLL PLAY MODE LEVEL/DISPLAY/CHAR 6 EJECT REPEAT Contents Sets continuous playback when pressed in the STOP state. When pressed during continuous playback, the tracking servo turns ON/OFF. Stops continuous playback and continuous recording. The sled moves to the outer circumference only when this is pressed. The sled moves to the inner circumference only when this is pressed. Switches between the pit and groove modes when pressed. Switches the spindle servo mode (CLVS ~ CLV A). Switches the displayed contents each time the button is pressed Ejects the disc Exits the test mode

7. TEST MODE DISPLAYS Each time the [DISPLAY/CHAR] button is pressed, the display changes in the following order.
1. Mode display Displays "TEMP ADJUST", "CPLAYMODE", etc.
Mode display

2. Error rate display Displays the error rate in the following way. C1 = AD = C1 = Indicates the C1 error. AD = Indicates ADER. 3. Address display The address is displayed as follows. (MO: recordable disc, CD: playback only disc) Pressing the [SCROLL/CLOCK SET] button switches between the group display and bit display. h = s = (MO pit and CD) h = a = (MO groove) h = Indicates the header address. s = Indicates the SUBQ address. a = Indicates the ADIP address.
Note: "­" is displayed when servo is not imposed.

Error rate display Address display Auto gain display (Not used in servicing) Detrack check display (Not used in servicing) IVR display (Not used in servicing)

4. Auto gain display (Not used in servicing) The auto gain is displayed as follows. AG = /[] 5. Detrack check display (Not used in servicing) The detrack is displayed as follows. ADR = 6. IVR display (Not used in servicing) The IVR is displayed as follows. [][][

­ 19 ­

MEANINGS OF OTHER DISPLAYS
Display ( P REC SYNC L.SYNC OVER B ATRACK DISC SLEEP MONO Contents When Lit During continuous playback (CLV: ON) Tracking servo OFF Recording mode ON CLV low speed mode ABCD adjustment completed Tracking offset cancel ON Tracking auto gain OK Focus auto gain OK Pit High reflection CLV-S CLV LOCK Groove Low reflection CLV-A CLV UNLOCK Tracking offset cancel OFF STOP (CLV: OFF) Tracking servo ON Recording mode OFF CLV normal mode When Off

­ 20 ­

SECTION 5 ELECTRICAL ADJUSTMENTS
1. PARTS REPLACEMENT AND ADJUSTMENT
· Check and adjust the mechanism deck as follows. The procedure changes according to the part replaced · Abbreviation OP : Optical pick-up OWH : Overwrite head

· Temperature compensation offset check · Laser power check · Traverse check · Focus bias check · C PLAY check · Self-recording/playback check OK

NG Parts Replacement and Repair

Check the sled and spindle mechanisms. Other causes can be suspected.

Has the OWH been replaced?

YES

NO

Has OP, IC171, IC101, or IC121 been replaced?

YES Initial setting of the adjustment value NO

Has OP or IC171 been replaced?

NO

YES IOP information recording (IOP value labeled on OP)

Has IC171 or D101 been replaced?

YES Temperature compensation offset adjustment

NO

· Laser power adjustment · Traverse adjustment · Focus bias adjustment · Error rate adjustment · Focus bias check · Auto gain adjustment

­ 21 ­

2. PRECAUTIONS FOR CHECKING LASER DIODE EMISSION
To check the emission of the laser diode during adjustments, never view directly from the top as this may lose your eye-sight.

3. PRECAUTIONS FOR USE OF OPTICAL PICK-UP (KMS-260A)
As the laser diode in the optical pick-up is easily damaged by static electricity, solder the laser tap of the flexible board when using it. Before disconnecting the connector, desolder first. Before connecting the connector, be careful not to remove the solder. Also take adequate measures to prevent damage by static electricity. Handle the flexible board with care as it breaks easily.
pick-up flexible board

4. Use the following tools and measuring devices. · Check Disc (MD) TDYS-1 (Parts No. 4-963-646-01) · TEST DISK (MDW-74/AU-1) (Parts No. 8-892-341-41) · Laser power meter LPM-8001 (Parts No. J-2501-046-A) or MD Laser power meter 8010S (Parts No. J-2501-145-A) · Oscilloscope (Measure after performing CAL of prove) · Digital voltmeter · Thermometer · Jig for checking BD board waveform (Parts No. : J-2501-149-A) 5. When observing several signals on the oscilloscope, etc., make sure that VC and ground do not connect inside the oscilloscope. (VC and ground will become short-circuited) 6. Using the above jig enables the waveform to be checked without the need to solder. (Refer to Servicing Notes on page 6) 7. As the disc used will affect the adjustment results, make sure that no dusts nor fingerprints are attached to it.

Laser power meter
When performing laser power checks and adjustment (electrical adjustment), use of the new MD laser power meter 8010S (J-2501145-A) instead of the conventional laser power meter is convenient. It sharply reduces the time and trouble to set the laser power meter sensor onto the objective lens of the pick-up.

laser tap

Optical pick-up flexible board

4. PRECAUTIONS FOR ADJUSTMENTS
1. When replacing the following parts, perform the adjustments and checks with ¬ in the order shown in the following table.
Optical Pick-up IC171 1. Initial setting of adjustment value 2. Recording of IOP information (Value written in the pick-up) 3. Temperature compensation offset adjustment 4. Laser power adjustment 5. Traverse adjustment 6. Focus bias adjustment 7. Error rate check 8. Auto gain output level adjustment ¬ ¬ BD Board D101 G IC101, IC121 IC192 ¬ G

5. CREATING CONTINUOUSLY-RECORDED DISC
* This disc is used in focus bias adjustment and error rate check. The following describes how to create a continuous recording disc. 1. Insert a disc (blank disc) commercially available. 2. Turn the = ~ + knob and display "CREC MODE". (C31) 3. Press the [YES] button again to display "CREC MID". Display "CREC (0300)" and start to recording. 4. Complete recording within 5 minutes. 5. Press the [MENU/NO] button and stop recording . 6. Press the [ EJECT] button and remove the disc. 6 The above has been how to create a continuous recorded data for the focus bias adjustment and error rate check.
Note : · Be careful not to apply vibration during continuous-recording.

¬

¬

G

G

G

G

¬

¬

G

G

¬ ¬

¬ ¬

G G

¬ ¬

¬ G

¬ ¬ ¬

¬ ¬ ¬

G G G

¬ ¬ ¬

G G G

2. Set the test mode when performing adjustments. After completing the adjustments, exit the test mode. Perform the adjustments and checks in "group S" of the test mode. 3. Perform the adjustments to be needed in the order shown.

­ 22 ­

6. CHECK PRIOR TO REPAIRS
These checks are performed before replacing parts according to "approximate specifications" to determine the faulty locations. For details, refer to "Checks Prior to Parts Replacement and Adjustments" (See page 8). 6-1. Temperature Compensation Offset Check When performing adjustments, set the internal temperature and room temperature of 22 °C to 28 °C. Checking Procedure: 1. Turn the = ~ + knob to display "TEMP CHECK" (C01). 2. Press the [YES] button. 3. "T=@@(##) [OK" should be displayed. If "T=@@ (##) [NG" is displayed, it means that the results are bad. (@@ indicates the current value set, and ## indicates the value written in the non-volatile memory) 6-2. Laser Power Check Before checking, check the IOP value of the optical pick-up. (Refer to 5-8. Recording and Displaying IOP Information) Connection :
laser power meter

Note 1: After step 4, each time the [YES] button is pressed, the display will be switched between "LD 0.7 mW $ ", "LD 6.2 mW $ ", and "LD Wp $ ". Nothing needs to be performed here.

6-3. Traverse Check
Note 1: Data will be erased during MO reading if a recorded disc is used in this adjustment. Note 2: If the traverse waveform is not clear, connect the oscilloscope as shown in the following figure so that it can be seen more clearly. oscilloscope (DC range)

BD board CN110 pin 3 (TEO) CN110 pin 1 (VC)

330 k
+ ­

10 pF

Connection :
oscilloscope (DC range) BD board CN110 pin 3 (TEO) CN110 pin 1 (VC)
+ ­

V: 0.1 V/div H: 10 ms/div

Optical pick-up objective lens

digital voltmeter BD board CN110 pin 5 (I +3V) CN110 pin 4 (IOP)
+ ­

Checking Procedure: 1. Set the laser power meter on the objective lens of the optical pick-up. (When it cannot be set properly, press the [ ] but0 ton or [ ] button to move the optical pick-up) ) Connect the digital volt meter to CN110 pin 5 (I+3V) and CN110 pin 4 (IOP). 2. Then, turn the = ~ + knob and display "LDPWR CHECK" (C02). 3. Press the [YES] button once and display "LD 0.9 mW $ ". Check that the reading of the laser power meter become 0.84 to 0.92 mW. 4. Press the [YES] button once more and display "LD 7.0 mW $ ". Check that the reading the laser power meter and digital volt meter satisfy the specified value. Specification: Laser power meter reading : 7.0 ± 0.2 mW Digital voltmeter reading : Optical pick-up displayed value ±10%
(Optical pick-up label)
KMS260A 27X40 B0825

Checking Procedure: 1. Connect an oscilloscope to CN110 pin 3 (TEO) and CN110 pin 1 (VC) of the BD board. 2. Load a disc (any available on the market). (Refer to Note 1) 3. Press the [ ] button and move the optical pick-up outside ) the pit. 4. Turn the = ~ + knob and display "EF MO CHECK"(C03). MO-R". 5. Press the [YES] button and display "EFB = (Laser power READ power/Focus servo ON/tracking servo OFF/spindle (S) servo ON) 6. Observe the waveform of the oscilloscope, and check that the specified value is satisfied. Do not turn the = ~ + knob. (Read power traverse checking)
(Traverse Waveform)
A VC B Specified value : Below 10% offset value Offset value (%) = IA ­ B I X 100 2 (A + B)

7. Press the [YES] button and display "EFB = MO-W". 8. Observe the waveform of the oscilloscope, and check that the specified value is satisfied. Do not turn the = ~ + knob. (Write power traverse checking)
(Traverse Waveform)
A VC B Specified value : Below 10% offset value Offset value (%) = IA ­ B I X 100 2 (A + B)

lOP=82.5 mA in this case lOP (mA) = Digital voltmeter reading (mV)/1 ()

5. Press the [MENU/NO] button and display "LDPWR CHECK" and stop the laser emission. (The [MENU/NO] button is effective at all times to stop the laser emission)

­ 23 ­

9. Press the [YES] button display "EFB = MO-P". Then, the optical pick-up moves to the pit area automatically and servo is imposed. 10. Observe the waveform of the oscilloscope, and check that the specified value is satisfied. Do not turn the = ~ + knob.
(Traverse Waveform)

A VC B Specified value : Below 10% offset value Offset value (%) = IA ­ B I X 100 2 (A + B)

11. Press the [YES] button display "EF MO CHECK" The disc stops rotating automatically. 12. Press the [ EJECT] button and remove the disc. 6 13. Load the check disc (MD) TDYS-1. 14. Turn the = ~ + knob and display "EF CD CHECK" (C04). CD". Servo is 15. Press the [YES] button and display "EFB = imposed automatically. 16. Observe the waveform of the oscilloscope, and check that the specified value is satisfied. Do not turn the = ~ + knob.
(Traverse Waveform)

6-4. Focus Bias Check Change the focus bias and check the focus tolerance amount. Checking Procedure : 1. Load the test disk (MDW-74/AU-1). 2. Turn the = ~ + knob and display "CPLAY MODE" (C30). 3. Press the [YES] button twice and display "CPLAY MID". 4. Press the [MENU/NO] button when "C = AD = " is displayed. 5. Turn the = ~ + knob and display "FBIAS CHECK" (C05). 6. Press the [YES] button and display " / c = ". The first four digits indicate the C1 error rate, the two digits after [/] indicate ADER, and the 2 digits after [c =] indicate the focus bias value. Check that the C1 error is below 50 and ADER is below 2. 7. Press the [YES] button and display " / b = ". Check that the C1 error is about 200 and ADER is below 2. 8. Press the [YES] button and display " / a = ". Check that the C1 error is about 200 and ADER is below 2. 9. Press the [MENU/NO] button, next press the [ EJECT] but6 ton and take out the test disc. 6-5. C PLAY Checking MO Error Rate Check Checking Procedure : 1. Load the test disk (MDW-74/AU-1). 2. Turn the = ~ + knob and display "CPLAY MODE" (C30). 3. Press the [YES] button and display "CPLAY MID". 4. The display changes to "C = AD = ". 5. If the C1 error rate is below 80, check that ADER is below 2. 6. Press the [MENU/NO] button, stop playback, press the [ EJECT] button and take out the test disc. 6 CD Error Rate Check Checking Procedure : 1. Load the check disc (MD) TDYS-1. 2. Turn the = ~ + knob and display "CPLAY MODE" (C30). 3. Press the [YES] button twice and display "CPLAY MID". 4. The display changes to "C = AD = ". 5. Check that the C1 error rate is below 50. 6. Press the [MENU/NO] button, stop playback, press the [ EJECT] button and take out the check disc. 6 6-6. Self-Recording/playback Check Prepare a continuous recording disc using the unit to be repaired and check the error rate. Checking Procedure : 1. Insert a recordable disc (blank disc) into the unit. 2. Turn the = ~ + knob to display "CREC MODE" (C31). 3. Press the [YES] button to display the "CREC MID". 4. When recording starts, " REC " is displayed, this becomes "CREC @@@@" (@@@@ is the address), and recording starts. 5. About 1 minute later, press the [MENU/NO] button to stop continuous recording. 6. Turn the = ~ + knob to display "CPLAY MODE" (C30). 7. Press the [YES] button to display "CPLAY MID". 8. "C = AD = " will be displayed. 9. Check that the C1 error becomes below 80 and the AD error below 2. 10. Press the [MENU/NO] button to stop playback, and press the [ EJECT] button and take out the disc. 6

A VC B Specified value : Below 10% offset value Offset value (%) = IA ­ B I X 100 2 (A + B)

17. Press the [YES] button and display "EF CD CHECK". 18. Press the [ EJECT] button and take out the check disc. 6

­ 24 ­

7. INITIAL SETTING OF ADJUSTMENT VALUE
Note: Mode which sets the adjustment results recorded in the non-volatile memory to the initial setting value. However the results of the temperature compensation offset adjustment will not change to the initial setting value. If initial setting is performed, perform all adjustments again excluding the temperature compensation offset adjustment. For details of the initial setting, refer to "4. Precautions on Adjustments" and execute the initial setting before the adjustment as required.

9. TEMPERATURE COMPENSATION OFFSET ADJUSTMENT
Save the temperature data at that time in the non-volatile memory as 25 °C reference data.
Note : 1. Usually, do not perform this adjustment. 2. Perform this adjustment in an ambient temperature of 22 °C to 28 °C. Perform it immediately after the power is turned on when the internal temperature of the unit is the same as the ambient temperature of 22 °C to 28 °C. 3. When D101 has been replaced, perform this adjustment after the temperature of this part has become the ambient temperature.

Setting Procedure : 1. Turn the = ~ + knob to display "ADJ CLEAR (C24)". 2. Press the [YES] button. "Complete!" will be displayed momentarily and initial setting will be executed, after which "ADJ CLEAR" will be displayed.

8. RECORDING AND DISPLAYING THE IOP INFORMATION
The IOP data can be recorded in the non-volatile memory. The IOP value on the label of the optical pickup and the IOP value after the adjustment will be recorded. Recording these data eliminates the need to read the label on the optical pick-up. Recording Procedure : 1. Turn the = ~ + knob to display "Iop Write" (C28), and press the [YES] button. 2. The display becomes Ref=@@@.@ (@ is an arbitrary number) and the numbers which can be changed will blink. 3. Input the IOP value written on the optical pick-up. To select the number : Turn the = ~ + knob. To select the digit : Press the = ~ + knob 4. When the [YES] button is pressed, the display becomes "Measu=@@@.@" (@ is an arbitrary number). 5. As the adjustment results are recorded for the 6 value. Leave it as it is and press the [YES] button. 6. "Complete!" will be displayed momentarily. The value will be recorded in the non-volatile memory and the display will become "Iop Write". Display Procedure : 1. Turn the = ~ + knob to display "Iop Read"(C27). 2. "@@.@/##.#" is displayed and the recorded contents are displayed. @@.@ indicates the IOP value labeled on the pick-up. ##.# indicates the IOP value after adjustment 3. To end, press the = ~ + button or [MENU/NO] button to display "Iop Read".

Adjusting Procedure : 1. Turn the = ~ + knob and display "TEMP ADJUST" (C09). 2. Press the [YES] button and select the "TEMP ADJUST" mode. 3. "TEMP = [OK" and the current temperature data will be displayed. 4. To save the data, press the [YES] button. When not saving the data, press the [MENU/NO] button. 5. When the [YES] button is pressed, "TEMP = SAVE" will be displayed and turned back to "TEMP ADJUST" display then. When the [MENU/NO] button is pressed, "TEMP ADJUST" will be displayed immediately. Specified Value : The "TEMP = " should be within "E0 - EF", "F0 - FF", "00 0F", "10 - 1F" and "20 - 2F".

10. LASER POWER ADJUSTMENT
Check the IOP value of the optical pick-up before adjustments. (Refer to 8. Recording and Displaying IOP Information) Connection :
laser power meter

Optical pick-up objective lens

digital voltmeter BD board CN110 pin 5 (I +3V) CN110 pin 4 (IOP)
+ ­

Adjusting Procedure : 1. Set the laser power meter on the objective lens of the optical pick-up. (When it cannot be set properly, press the [ ] button 0 or [ ] button to move the optical pick-up.) ) Connect the digital volt meter to CN110 pin 5 (I+3V) and CN110 pin 4 (IOP). 2. Turn the = ~ + knob and display "LDPWR ADJUST" (C10). (Laser power : For adjustment) 3. Press the [YES] button once and display "LD 0.9 mW $ ". 4. Turn the = ~ + knob so that the reading of the laser power meter becomes 0.85 to 0.91 mW. Press the [YES] button after setting the range knob of the laser power meter, and save the adjustment results. ("LD SAVE $ " will be displayed for a moment.) 5. Then "LD 7.0 mW $ " will be displayed. 6. Turn the = ~ + knob so that the reading of the laser power meter becomes 6.9 to 7.1 mW, press the [YES] button and save it.
Note: Do not perform the emission with 7.0 mW more than 15 seconds continuously.

­ 25 ­

7. Then, turn the = ~ + knob and display "LDPWR CHECK" (C02). 8. Press the [YES] button once and display "LD 0.9 mW $ ". Check that the reading of the laser power meter become 0.85 to 0.91 mW. 9. Press the [YES] button once more and display "LD 7.0 mW $ ". Check that the reading the laser power meter and digital volt meter satisfy the specified value. Note down the digital voltmeter reading value. Specification: Laser power meter reading : 7.0 ± 0.2 mW Digital voltmeter reading : Optical pick-up displayed value ±10%
(Optical pick-up label)
KMS260A 27X40 B0825

11. TRAVERSE ADJUSTMENT
Note 1:Data will be erased during MO reading if a recorded disc is used in this adjustment. Note 2:If the traverse waveform is not clear, connect the oscilloscope as shown in the following figure so that it can be seen more clearly. oscilloscope (DC range)

BD board CN110 pin 3 (TEO) CN110 pin 1 (VC)

330 k
+ ­

10 pF

Connection :
oscilloscope (DC range) BD board CN110 pin 3 (TEO) CN110 pin 1 (VC)
+ ­

V: 0.1 V/div H: 10 ms/div

lOP=82.5 mA in this case lOP (mA) = Digital voltmeter reading (mV)/1 ()

10. Press the [MENU/NO] button and display "LDPWR CHECK" and stop the laser emission. (The [MENU/NO] button is effective at all times to stop the laser emission.) 11. Turn the = ~ + knob to display "Iop Write"(C28). 12. Press the [YES] button. When the display becomes Ref=@@@.@ (@ is an arbitrary number), press the [YES] button to display "Measu=@@@.@" (@ is an arbitrary number). 13. The numbers which can be changed will blink. Input the Iop value noted down at step 9. To select the number : Turn the = ~ + knob. To select the digit : Press the = ~ + knob. 14. When the [YES] button is pressed, "Complete!" will be displayed momentarily. The value will be recorded in the nonvolatile memory and the display will become "Iop Write".
Note 1: After step 4, each time the [YES] button is pressed, the display will be switched between "LD 0.7 mW $ ", "LD 6.2 mW $ ", and "LD Wp $ ". Nothing needs to be performed here.

Adjusting Procedure : 1. Connect an oscilloscope to CN110 pin 3 (TEO) and CN110 pin 1 (VC) of the BD board. 2. Load a disc (any available on the market). (Refer to Note 1) 3. Press the [ ] button and move the optical pick-up outside ) the pit. 4. Turn the = ~ + knob and display "EF MO ADJUST" (C10). MO-R". 5. Press the [YES] button and display "EFB = (Laser power READ power/Focus servo ON/tracking servo OFF/spindle (S) servo ON) 6. Turn the = ~ + knob so that the waveform of the oscilloscope becomes the specified value. of "EFB= (When the = ~ + knob is turned, the " changes and the waveform changes.) In this adjustment, waveform varies at intervals of approx. 2%. Adjust the waveform so that the specified value is satisfied as much as possible. (Read power traverse adjustment)
(Traverse Waveform)
A VC B Specification A = B

7. Press the [YES] button and save the result of adjustment to the non-volatile memory ("EFB = SAV" will be displayed for a moment. Then "EFB = MO-W" will be displayed).

­ 26 ­

8. Turn the = ~ + knob so that the waveform of the oscilloscope becomes the specified value. of "EFB(When the = ~ + knob is turned, the " changes and the waveform changes.) In this adjustment, waveform varies at intervals of approx. 2%. Adjust the waveform so that the specified value is satisfied as much as possible. (Write power traverse adjustment)
(Traverse Waveform)

18. Press the [YES] button, display "EFB = SAV" for a moment and save the adjustment results in the non-volatile memory. Next "EF CD ADJUST" will be displayed. 19. Press the [ EJECT] button and take out the disc. 6

12. FOCUS BIAS ADJUSTMENT
Adjusting Procedure : 1. Load the continuously-recorded disc. (Refer to "5. CREATING CONTINUOUSLY-RECORDED DISC") 2. Turn the = ~ + knob and display "CPLAY MODE" (C29). 3. Press the [YES] button and display "CPLAY MID". 4. Press the [MENU/NO] button when "C1 = AD = " is displayed. 5. Turn the = ~ + knob and display "FBIAS ADJUST" (C13). 6. Press the [YES] button and display " / a = ". The first four digits indicate the C1 error rate, the two digits after [/] indicate ADER, and the 2 digits after [a =] indicate the focus bias value. 7. Turn the = ~ + knob in the clockwise direction and find the focus bias value at which the C1 error rate becomes about 200 (Refer to Note 2). / b = ". 8. Press the [YES] button and display " 9. Turn the = ~ + knob in the counterclockwise direction and find the focus bias value at which the C1 error rate becomes about 200. 10. Press the [YES] button and display " / c = ". 11. Check that the C1 error rate is below 50 and ADER is 00. Then press the [YES] button. 12. If the "( )" in " - - ( )" is above 20, press the [YES] button. If below 20, press the [MENU/NO] button and repeat the adjustment from step 2. 13. Press the [ EJECT] button and take out the disc. 6
Note 1: The relation between the C1 error and focus bias is as shown in the following figure. Find points A and B in the following figure using the above adjustment. The focal point position C is automatically calculated from points A and B. Note 2: As the C1 error rate changes, perform the adjustment using the average vale.

A VC B Specification A = B

9. Press the [YES] button, and save the adjustment results in the non-volatile memory. ("EFB = SAV" will be displayed for a moment.) 10. "EFB = MO-P". will be displayed. The optical pick-up moves to the pit area automatically and servo is imposed. 11. Turn the = ~ + knob until the waveform of the oscilloscope moves closer to the specified value. In this adjustment, waveform varies at intervals of approx. 2%. Adjust the waveform so that the specified value is satisfied as much as possible.
(Traverse Waveform)
A VC B Specification A = B

12. Press the [YES] button, and save the adjustment results in the SAV" will be displayed for non-volatile memory. ("EFB = a moment.) Next "EF MO ADJUST" is displayed. The disc stops rotating automatically. 13. Press the [ EJECT] button and take out the disc. 6 14. Load the check disc (MD) TDYS-1. 15. Turn the = ~ + knob and display "EF CD ADJUST" (C12). 16. Press the [YES] button and display "EFB = CD". Servo is imposed automatically. 17. Turn the = ~ + knob so that the waveform of the oscilloscope moves closer to the specified value. In this adjustment, waveform varies at intervals of approx. 2%. Adjust the waveform so that the specified value is satisfied as much as possible.
(Traverse Waveform)
A VC B Specification A = B

C1 error about 200

B

C

A

Focus bias value (F. BIAS)

­ 27 ­

13. ERROR RATE CHECK
13-1. CD Error Rate Check Checking Procedure : 1. Load the check disc (MD) TDYS-1. 2. Turn the = ~ + knob and display "CPLAY MODE" (C30). 3. Press the [YES] button twice and display "CPLAY MID". 4. The display changes to "C1 = AD = ". 5. Check that the C1 error rate is below 20. 6. Press the [MENU/NO] button, stop playback, press the [ EJECT] button and take out the check disc. 6 13-2. MO Error Rate Check Checking Procedure : 1. Load the test disc (MDW-74/AU-1). 2. Turn the = ~ + knob and display "CPLAY MODE" (C30). 3. Press the [YES] button and display "CPLAY MID". 4. The display changes to "C1 = AD = ". 5. If the C1 error rate is below 50, check that ADER is 00. 6. Press the [MENU/NO] button, stop playback, press the [ EJECT] button and take out the test disc. 6

15. AUTO GAIN CONTROL OUTPUT LEVEL ADJUSTMENT
Be sure to perform this adjustment when the pickup is replaced. If the adjustment results becomes "Adjust NG!", the pickup may be faulty or the servo system circuits may be abnormal. 15-1. CD Auto Gain Control Output Level Adjustment Adjusting Procedure : 1. Insert the check disc (MD) TDYS-1. 2. Turn the = ~ + knob to display "AG Set (CD)" (C26). 3. When the [YES] button is pressed, the adjustment will be performed automatically. "Complete!!" will then be displayed momentarily when the value is recorded in the non-volatile memory, after which the display changes to "AG Set (CD)". 4. Press the [ EJECT] button and take out the check disc. 6 15-2. MO Auto Gain Control Output Level Adjustment Adjusting Procedure : 1. Insert the test disc (MDW-74/AU-1) for recording. 2. Turn the = ~ + knob to display "AG Set (MO)" (C25). 3. When the [YES] button is pressed, the adjustment will be performed automatically. "Complete!!" will then be displayed momentarily when the value is recorded in the non-volatile memory, after which the display changes to "AG Set (MO)". 4. Press the [ EJECT] button and take out the test disc. 6

14. FOCUS BIAS CHECK
Change the focus bias and check the focus tolerance amount. Checking Procedure : 1. Load the continuously-recorded disc. (Refer to "5. CREATING CONTINUOUSLY-RECORDED DISC") 2. Turn the = ~ + knob and display "CPLAY MODE" (C30). 3. Press the [YES] button twice and display "CPLAY MID". AD = " is 4. Press the [MENU/NO] button when "C1 = displayed. 5. Turn the = ~ + knob and display "FBIAS CHECK" (C05). 6. Press the [YES] button and display " / c = ". The first four digits indicate the C1 error rate, the two digits after [/] indicate ADER, and the 2 digits after [c =] indicate the focus bias value. Check that the C1 error is below 50 and ADER is below 2. 7. Press the [YES] button and display " / b = ". Check that the C1 error is about 200 and ADER is below 2. / a = ". 8. Press the [YES] button and display " Check that the C1 error is about 200 and ADER is below 2 9. Press the [MENU/NO] button, next press the [ EJECT] but6 ton and take out the disc.
Note 1: If the C1 error and ADER are above other than the specified value at points a (step 8. in the above) or b (step 7. in the above), the focus bias adjustment may not have been carried out properly. Adjust perform the beginning again.

­ 28 ­

Adjustment Location:
­ BD BOARD (Side A) ­
CN101 D101

CN110

GND I+3V IOP TEO RF VC

NOTE

IC171

­ BD BOARD (Side B) ­

IC101

IC121

IC192

Note: It is useful to use the jig. for checking the waveform. (Refer to Servicing Notes on page 6)

­ 29 ­

SECTION 6 DIAGRAMS
6-1. IC PIN FUNCTION DESCRIPTION
· BD BOARD IC101 CXA2523AR (RF AMP, FOCUS/TRACKING ERROR AMP) Pin No. 1 2 3 4 to 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 Pin Name I J VC A to F PD APC APCREF GND TEMPI TEMPR SWDT SCLK XLAT XSTBY F0CNT VREF EQADJ 3TADJ VCC WBLADJ TE CSLED SE ADFM ADIN ADAGC ADFG AUX FE ABCD BOTM PEAK RF RFAGC AGCI COMPO COMPP ADDC OPO OPN RFO MORFI MORFO I/O I I O I I O I -- I O I I I I I O I I -- I O I O O I I O O O O O O O I I O I I O I O I O Description I-V converted RF signal I input from the optical pick-up block detector I-V converted RF signal J input from the optical pick-up block detector Middle point voltage (+1.65V) generation output terminal Signal input from the optical pick-up detector Light amount monitor input from the optical pick-up block laser diode Laser amplifier output terminal to the automatic power control circuit Reference voltage input terminal for setting laser power Ground terminal Connected to the temperature sensor Output terminal for a temperature sensor reference voltage Writing serial data input from the CXD2654R (IC121) Serial data transfer clock signal input from the CXD2654R (IC121) Serial data latch pulse signal input from the CXD2654R (IC121) Standby signal input terminal "L": standby (fixed at "H" in this set) Center frequency control voltage input terminal of internal circuit (BPF22, BPF3T, EQ) input from the CXD2654R (IC121) Reference voltage output terminal Not used (open) Center frequency setting terminal for the internal circuit (EQ) Center frequency setting terminal for the internal circuit (BPF3T) Power supply terminal (+3.3V) Center frequency setting terminal for the internal circuit (BPF22) Tracking error signal output to the CXD2654R (IC121) Connected to the external capacitor for low-pass filter of the sled error signal Sled error signal output to the CXD2654R (IC121) FM signal output of the ADIP Receives a ADIP FM signal in AC coupling Connected to the external capacitor for ADIP AGC ADIP duplex signal (22.05 kHz ± 1 kHz) output to the CXD2654R (IC121) Auxiliary signal (I3 signal/temperature signal) output to the CXD2654R (IC121) Focus error signal output to the CXD2654R (IC121) Light amount signal (ABCD) output to the CXD2654R (IC121) Light amount signal (RF/ABCD) bottom hold output to the CXD2654R (IC121) Light amount signal (RF/ABCD) peak hold output to the CXD2654R (IC121) Playback EFM RF signal output to the CXD2654R (IC121) Connected to the external capacitor for RF auto gain control circuit Receives a RF signal in AC coupling User comparator output terminal Not used (open) User comparator input terminal Not used (fixed at "L") Connected to the external capacitor for cutting the low band of the ADIP amplifier User operational amplifier output terminal Not used (open) User operational amplifier inversion input terminal Not used (fixed at "L") RF signal output terminal Receives a MO RF signal in AC coupling MO RF signal output terminal

­ 30 ­

· BD BOARD IC121 CXD2654R (DIGITAL SIGNAL PROCESSOR, DIGITAL SERVO PROCESSOR, EFM/ACIRC ENCODER/DECODER, SHOCK PROOF MEMORY CONTROLLER, ATRAC ENCODER/DECODER) Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 to 34 35 36 to 40 41 42 43 44 Pin Name MNT0 (FOK) MNT1 (SHOCK) MNT2 (XBUSY) MNT3 (SLOCK) SWDT SCLK XLAT SRDT SENS XRST SQSY DQSY RECP XINT TX OSCI OSCO XTSL DIN0 DIN1 DOUT DATAI LRCKI XBCKI ADDT DADT LRCK XBCK FS256 DVDD A03 to A00 A10 A04 to A08 A11 DVSS XOE XCAS I/O O O O O I I (S) I (S) O (3) O (3) I (S) O O I O I I O I I I O I I I I O O O O -- O O O O -- O O Description Focus OK signal output to the system controller (IC501) "H" is output when focus is on ("L": NG) Track jump detection signal output to the system controller (IC501) Busy monitor signal output to the system controller (IC501) Spindle servo lock status monitor signal output to the system controller (IC501) Writing serial data signal input from the system controller (IC501) Serial data transfer clock signal input from the system controller (IC501) Serial data latch pulse signal input from the system controller (IC501) Reading serial data signal output to the system controller (IC501) Internal status (SENSE) output to the system controller (IC501) Reset signal input from the system controller (IC501) "L": reset Subcode Q sync (SCOR) output to the system controller (IC501) "L" is output every 13.3 msec Almost all, "H" is output Digital In U-bit CD format subcode Q sync (SCOR) output to the system controller (IC501) "L" is output every 13.3 msec Almost all, "H" is output Laser power selection signal input from the system controller (IC501) "L": playback mode, "H": recording mode Interrupt status output to the system controller (IC501) Recording data output enable signal input from the system controller (IC501) Writing data transmission timing input (Also serves as the magnetic head on/off output) System clock signal (512Fs=22.5792 MHz) input terminal System clock signal (512Fs=22.5792 MHz) output terminal Not used (open) Input terminal for the system clock frequency setting "L": 45.1584 MHz, "H": 22.5792 MHz (fixed at "H" in this set) Digital audio signal input terminal when recording mode (for digital optical input) Digital audio signal input terminal when recording mode (for digital optical input) Digital audio signal output terminal when playback mode (for digital optical output) Not used Serial data input terminal Not used (fixed at "L") L/R sampling clock signal (44.1 kHz) input terminal Not used (fixed at "L") Bit clock signal (2.8224 MHz) input terminal Not used (fixed at "L") Recording data input from the A/D, D/A converter (IC301) Playback data output to the A/D, D/A converter (IC301) L/R sampling clock signal (44.1 kHz) output to the A/D, D/A converter (IC301) Bit clock signal (2.8224 MHz) output to the A/D, D/A converter (IC301) Clock signal (11.2896 MHz) output terminal Not used (open) Power supply terminal (+3.3V) (digital system) Address signal output to the D-RAM (IC124) Address signal output to the external D-RAM Not used (open) Address signal output to the D-RAM (IC124) Address signal output to the external D-RAM Not used (open) Ground terminal (digital system) Output enable signal output to the D-RAM (IC124) "L" active Column address strobe signal output to the D-RAM (IC124) "L" active Not used

* I (S) stands for schmitt input, I (A) for analog input, O (3) for 3-state output, and O (A) for analog output in the column I/O.

­ 31 ­

Pin No. 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89

Pin Name A09 XRAS XWE D1 D0 D2 D3 MVCI ASYO ASYI AVDD BIAS RFI AVSS PCO FILI FILO CLTV PEAK BOTM ABCD FE AUX1 VC ADIO AVDD ADRT ADRB AVSS SE TE DCHG APC ADFG F0CNT XLRF CKRF DTRF APCREF LDDR TRDR TFDR DVDD FFDR FRDR

I/O O O O I/O I/O I/O I/O I (S) O I (A) -- I (A) I (A) -- O (3) I (A) I (A) I (A) I (A) I (A) I (A) I (A) I (A) -- I (A) I (A) -- I (A) I (A) I (A) I (A) I (S) O O O O O O O O -- O O

Description Address signal output to the D-RAM (IC124) Row address strobe signal output to the D-RAM (IC124) "L" active Write enable signal output to the D-RAM (IC124) "L" active

Two-way data bus with the D-RAM (IC124)

Digital in PLL oscillation input from the external VCO Not used (fixed at "L") Playback EFM full-swing output terminal Playback EFM asymmetry comparator voltage input terminal Power supply terminal (+3.3V) (analog system) Playback EFM asymmetry circuit constant current input terminal Playback EFM RF signal input from the CXA2523AR (IC101) Ground termin