Text preview for : service.pdf part of Philips service Philips Audio HTL1190B12 service.pdf
Back to : service.pdf | Home
Sound Stage HTL1190B/ALL
Service
TABLE OF CONTENTS
Chapter
Location of PC Boards & Versions Variation ........................ 1
Speci cations ....................................................................... 2
Safety Instruction .................................................................. 3
Software Upgrade Instruction..................................................4
Troubleshooting.................................................................... 5
Disassembly Instructions ..................................................... 6
Set Block Diagram ................................................................ 7
Circuit Diagram & PCBA Layout........................................... 8
Set Mechanical Exploded View ........................................... 9
Revision List ........................................................................ 10
Published by DX_LI WK1441 Subject to modification 3140 038 62540
Version 1.0
1. Location of PC Boards & Versions Variation
USB and AUDIO IN Board POWER and MAIN Board
LED Display Board Key Board
Versiongs Variation
Type/Version HTL11
B/
Board in used service Policy
POWER and MAIN Board C
LED Display Board M+C
Key Board M+C
USB and ADUIO IN Board M+C
Tips:C--Component Level Repair
M--Module Level Rpair
2
100-240V~,50HZ/60HZ
3 .Safety instruction, Warning & Notes
Safety instruction
1. General safety
2.Laser safety
Safety regulations require that during a repair:
This unit employs a laser. Only qualified service personnel
. Connect the unit to the mains via an isolation transformer.
may remove the cover, or attempt to service this device
. Replace safety components indicated by the symbol ,
(due to possible eye injury).
only by components identical to the original ones. Any
Laser device unit
other component substitution (other than original type)
Type : Semiconductor laser GaAlAs
may increase risk of fire or electrical shock hazard.
Wavelength : 650nm (DVD)
: 780nm (VCD/CD)
Safety regulations require that after a repair, you must
Output power : 7mW (DVD)
return the unit in its original condition. Pay, in particular,
: 10mW (DVD /CD)
attention to the following points:
Beam divergence: 60 degree
. Route the wires/cables correctly, and fix them with the
Note: Use of controls or adjustments or performance of
mounted cable clamps.
procedure other than those specified herein, may result in
. Check the insulation of the mains lead for external
hazardous radiation exposure. Avoid direct exposure to
damage.
beam.
. Check the electrical DC resistance between the mains
plug and the secondary side:
1) Unplug the mains cord, and connect a wire between
the two pins of the mains plug.
2) Set the mains switch the "on" position (keep the
mains cord unplug).
3) Measure the resistance value between the mains
plug and the front panel, controls, and chassis
bottom.
4) Repair or correct unit when the resistance
measurement is less than 1M .
5) Verify this, before you return the unit to the
customer/user (ref. UL-standard no. 1492).
6) Switch the unit "off", and remove the wire between
the two pins of the mains plug.
4. Software Upgrade Instruction
In HTL11 0B models, S
oftware to upgrade:
Main board software Update procedure:
Step 1: Rename Bin name to HTL1190.BIN, and copy file to U disk root directory
Step 2: Switch source to AUDIO IN mode, insert UDisk.
Step 3: Switch source to AUX mode, then switch source to USB mode in 55s.
Step 4: Wait for HTL1190 re ad firmware from UDisk, if firmware is correct, upgrade start, all LEDs light on.
Step 5: Wait for upgrade finished: when finished, all LEDs will blink.
Step 6: Unplug AC line, press&hold local POWER key, plug AC line, until all LEDs blink, FACTORY RESET action is triggered
Note:
If switch from AUX to USB mode within 60 sec, allow the USB firmware upgrade.
If from Aux mode, exceed 60 sec then switch to USB, do not trigger the USB firmware upgrade.
USB device:
Support USB 1.1, 2.0 FS.
Support USB Filesystem FAT16 ,FAT32 and NTFS
Don't distinguish upper and lower letters for FW name
When upgrading, all LEDs turn ON.
After upgrade successfully, blink all LED 3 times(rate of once every second) after that reboot.
In HTL11 0B models, there are two me
thods to FACTORY RESET STEP:
Method One:
for RC method
Switch to MUTE status, and then quickly press AUX key for two times within 800ms (<800ms),
System will show software version for 3 seconds, and go to factory reset
Method Two:
for local method
the Press and Hold local_key_STANDBY while power up the mains to trigger the RESTORE FACTORY DEFAULT
setting.
5.Trouble shooting Chart
ANO POWER ON
Whether Remote is OK NO Change another remote
YES
NO
Whether AC connect is OK Check Input AC 110V
YES
NO Check power board and relative
Whether output power 18V is OK
connect line
YES
NO Check relative component of U3
Whether U3 output 5V
whether OK
YES
NO Check relative component of U1
Whether U1 output 3.3V
whether OK
YES
NO Check relative component of U2
Whether U2 output 1.3V
whether OK
YES
Whether 12PIN FFC cableand NO Check relative component with
relative component s are OK CON1 and 12PIN FFC cableand
YES
Replace LED board
BNO LED display
Whether CON1 and 12pin FCC NO Repair or replace 12pin FFC
cable OK cable
YES
Whether U1 supply voltage NO
Repair or replace U1
normal
YES
Whether control signal and NO
Repair or replace U6
control current
YES
Replace LED board
CRemote control does
not work
NO Replace battery or enhance
Whether battery is OK
battery with pole connect
YES
Whether CON1 and 12pin FCC NO Repair or replace 12pin FFC
cable OK cable
YES
Whether PIN29 Signal of the U6 NO
Repair or replace U6
is normal
YES
Change another Remote control
DAUX IN NO Output
NO
Whether LED State Check remote control Mute key
YES
Whether Pin7PIN16 voltage of NO
Check power supply of U9 and Q20
U9 is normal
YES
Whether Q20 power supply is NO Check relative comment about
normal connect power
YES
Whether Q20 output DC voltage NO
Repair or replace Q20
is 18V
YES
Whether Pin9PIN10 Signal of NO
Repair or replace U9
the U9 is normal
YES
Whether PIN4 of the U15 supply NO
Change The U15
voltage normal
YES
Check control signal pin6~8 of
the U15 OK
EAUDIO IN NO Output
NO
Whether LED State Check remote control Mute key
YES
Whether Q20 power supply is NO Check relative comment about
normal connect power
YES
Whether Q20 output DC voltage NO
Repair or replace Q20
is 18V
YES
Whether Pin9PIN10 Signal of NO
Repair or replace U9
the U9 is normal
YES
Whether PIN4 of the U15 supply NO
Repair or replace U15
voltage normal
YES
Check control signal pin6~8 of NO
Change The U15
the U15 OK
YES
Whether CON3 and 3pin Shielded NO Repair or replace 3pin Shielded
wire OK wire
YES
Replace USB and AUDIO IN board
FCoax NO Output
NO
Whether LED State Check remote control Mute key
YES
Whether Q1 power supply is NO Check relative comment about
normal connect power
YES
Whether PIN14 voltage of U10 is NO
Repair or replace U10
normal
YES
Whether Pin4 Signal of the U10 NO
Repair or replace U10
is normal
YES
Whether Pin16 Signal of the U6 NO
Change The U6
is normal
YES
Check control signal pin16 of
U6 OK
GOpt NO Output
NO
Whether LED State Check remote control Mute key
YES
Whether Pin17 Signal of the U6 NO
Change The U6
is normal
YES
Check control signal pin17 of
U6 OK
6. Dismantling Instruction
Mechanical and Dismantling Instructions
The following guidelines show how to dismantle the soundbar.
Step1: Remove 15 screws around the back panel, and then open the back panel (Figure 1)
Figure 1
Step2: Dismantle POWER and MAIN Board.Disconnect connectors(CON3,J2,CON2,CON7).
remove 5 screws on the panel.
Finally remove 2 screw on the shield bracket and remove 3 screws on the Power
and Main Board,Disconnect connectors(J1,CON1,)(Figure 2)
CON3 J2 CON2 and CON7
CON1
J1
Figure 2
Step3: remove 3 screws on the Key Board (Figure 3)
Figure 3
Step4: remove 2 screws on the LED Display Board (Figure 4)
Figure 4
Step5: Dismantle USB and ADUIO IN Board Disconnect connectors(CON1,CON2).
remove 2 screws on the USB and ADUIO IN Board.(Figure 5)
CON2 CON1
Figure 5
7.Set Block Diagram
MP3 Line IN
AUX
IN
Bluetooth moudle
F-6688 Ctrl Flash SDRAM
16M 4x64M
L/R
L R
VCC
SPI
L/R
74HC4052
Ctrl
vcc
R_Out ADC
I2S IN
L_Out PCM1808
L L=8 /20W
ECO_DET
R
MCLK
OP
BCLK
Optical
IN
OPTICAL IN MTK LRCK
I2S
Coaxial
IN
0
0
&
0
Coaxial IN
MT8307
74HC04
+5V/1A
USB
DP
Port DM
SDA
SCL
Amp STA369BWS R=8 /20W
3.3V
1.2V
VCC
Data
Data
VCC Light Display and IR IR Key Board
standby Optical Coaxial AUX BT
5 4 3 2 1
8.Circuit Diagram & PCBA Layout Rev
V1 Original release MT8307P1_V1
History P# Date
2013.01.10
8-1.Main Board Circuit Diagram: INDEX & Power
D D
MT8307 128 PIN GPIO LIST
NAME PIN FEATURES OFF-PAGE CONNECTION
GPIO30 99 IIC_SDA
AMP_18V
AMP_18V <5>
GPIO31 100 IIC_SCL VCC
VCC <2>
+5V
+5V <2,3>
P_3V3
P_3V3 <2,3,4>
GPIO32 101 CP_RST DV33
DV33 <2>
8307_3V3
8307_3V3 <2>
V12
V12 <2>
UP1_6 25 HDMI_SCL Power_Standby
Power_Standby <2,5>
3V3
U1
ADS6118/SOT-223 Close Q1 UP1_7 26 HDMI_SDA GND
RCR1525SI GND <2,3,4,5>
VCC D1 SS14 D2 1N4007 2 3 L1 FB 3V3 2 3 P_3v3
VIN OUT
GPIO3 31 CEC
ADJ
Power
+
1
+ + R3 100K R2 1K C1 EC3 GPIO4 32 ALRCK
1
EC1 C2 EC2 0.1UF 47uF/10V
100uF/10V R1 0.1UF 220uF/10V
NC C3 GPO5 6 BL_EN
R4 0 0.1UF
GPIO6 31 SD_CLK TxD
3
Q2 2 R5 4.7K Power_Standby
2N3904 GPIO7 40
R6 100K
1
C GPIO8 39 ACLK C
Default Power Ctrl
1 ON GPIO9 38 ABCK
1V2
U2 0 OFF
ADS5216/SOT89 Q3 GPIO10 84 HPLG
RCR1525SI
3V3 D3 1N4007 2 3 L2 FB vcc 2 3 +5V
VIN OUT
GPIO11 27 SD_CMD RxD
ADJ
+
1
+ + R7 100K R8 1K C5 EC6 GPIO12 83 ASPDIF
1
EC4 C4 EC5 0.1UF 47uF/10V
100uF/10V 0.1UF 220uF/10V
GND
C6 GPIO13 37 SD_D0
R9 0
0.1UF
GPO14 104 A_MUTE
3
Q4 2 R10 4.7K Power_Standby GPIO19 111 MCDATA
2N3904
R11 100K Default Power Ctrl
1
GPIO20 112 STBY_CTRL
1 ON
0 OFF GPIO21 113 BT_RST
LFE/GPIO 118 ARF
ABCK 119 Audio_SW2 IN
R1
R12 3.9K/1% ALRCK 123 Audio_SW1 IN
B B
C7 332pF
3V3
ASDATA0 124 VSTB
L3 8307_3V3
68uH/2A GPIO34 115 VSCK
AMP_18V SS14 D4 VCC L4 FB
GPIO35 116 VSDA
C8 + C9 + EC33 + EC8 C10 GPIO33 102 GPIO33
1
2
3
4
EC7 R13 EC9 + 100uF/10V 220uF/10V 0.1uF
0.1uF 47UF/35V 1.2K/1% 0.1uF GPIO29 98 AMP_EN
OUT
Vin
FB
EN
D5 470UF/10V
R14
R2 SS24
0R DV_Y2 16 SPDIFIN1
U3
ADS9129 DV33
GND
GND
GND
GND
DV_Y3 17 SPDIFIN2
L5 FB
8
7
6
5
DV_Y4 18 SPDIFIN3
VOUT=1.23*<1+R1/R2> + C11
EC10 0.1uF
SD_MS_D2 19 UART_RX
100uF/10V
SD_MS_D3 20 UART_TX
DV_C0 33 SPMCLK
1V2 DV_C1 34 SPBCK
V12
Close DV_C2 35 SPLRCK
L6 FB V12
A DV_C3 36 SPDATA A
+ C12
EC11 0.1uF
220uF/10V
5 4 3 2 1
5 4 3 2 1
8-2.Main Board Circuit Diagram: MT8307 & SDARM
V12
R16 100K
R17 0R RFV12-1 C13 0.1uF Y1 OFF-PAGE CONNECTION
XI XO
C15 27MHz C16 ADC_I2S
ADC_I2S <3>
2014.07.22 delete R24 MCLK
MCLK <3,4>
R22 12R RFV12-2 C17 0.1uF 27pF 27pF LRCK
LRCK <3,4>
R24 0R BCLK
BCLK <3,4>
I2S_OUT
I2S_OUT <4>
Put these circuits as
A_DET
closer as possible to A_DET <3>
SPDIF_IN1
Crystal
Importance. layout close to IC pin.
MT1389 SPDIF_IN1 <3>
D D
AUDIO I/F
8307_3V3
SDA
220uF/10v
SDA <4>
V1P4 SCL
0.1uF
SCL <4>