Text preview for : SMKOR63DB.pdf part of daewoo kor-63db9s microwave kor-63bbb9s/63db0s/63fb9s/63fb0s
Back to : SMKOR63DB.pdf | Home
S/M No. : R63DB9S002
Service Manual
Microwave Oven
Model: KOR-63DB9S KOR-63DB0S KOR-63FB9S KOR-63FB0S
DAEWOO ELECTRONICS CO., LTD.
PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY
(a) Do not operate or allow the oven to be operated with the door open. (b) Make the following safety checks on all ovens to be serviced before activating the magnetron or other microwave source, and make repairs as necessary: (1) Interlock operation, (2) Proper door closing, (3) Seal and sealing surfaces (arcing, wear, and other damage), (4) Damage to or loosening of hinges and latches, (5) Evidence of dropping or abuse. (c) Before turning on power to the microwave oven for any service test or inspection within the microwave generating compartments, check the magnetron, wave guide or transmission line, and cavity for proper alignment, integrity, and connections. (d) Any defective or misadjusted components in the interlock, monitor, door seal, and microwave generation and transmission systems shall be repaired, replaced, or adjusted by procedures described in this manual before the oven is released to the owner. (e) A microwave leakage check to verify compliance with the Federal performance standard should be performed on each oven prior to release to the owner.
TABLE OF CONTENTS
SAFETY AND PRECAUTIONS ...........................................................................................................................................2 1. FOR SAFE OPERATION ..................................................................................................................................2 2. FOR SAFE SERVICE PROCEDURES .............................................................................................................2 SPECIFICATIONS ...............................................................................................................................................................3 EXTERNAL VIEW ................................................................................................................................................................4 1. OUTER DIMENSION .........................................................................................................................................4 2. FEATURE DIAGRAM ........................................................................................................................................5 3. CONTROL PANEL ............................................................................................................................................6 INSTALLATION ...................................................................................................................................................................7 OPERATIONS AND FUNCTIONS .......................................................................................................................................8 DISASSEMBLY AND ASSEMBLY......................................................................................................................................9 INTERLOCK MECHANISM AND ADJUSTMENT .............................................................................................................16 TROUBLE SHOOTING GUIDE .........................................................................................................................................17 MEASUREMENT AND TEST ............................................................................................................................................21 1. MEASUREMENT OF THE MICROWAVE POWER OUTPUT ........................................................................21 2. MICROWAVE RADIATION TEST ...................................................................................................................22 3. COMPONENT TEST PROCEDURE ...............................................................................................................23 WIRING DIAGRAM ............................................................................................................................................................24 PRINTED CIRCUIT BOARD ..............................................................................................................................................25 1. CIRCUIT CHECK PROCEDURE ....................................................................................................................25 2. PCB CIRCUIT DIAGRAM ................................................................................................................................28 3. P.C.B. LOCATION NO ....................................................................................................................................29 EXPLODED VIEW AND PARTS LIST...............................................................................................................................30 1. DOOR ASSEMBLY .........................................................................................................................................30 2. CONTROL PANEL ASSEMBLY ......................................................................................................................30 3. TOTAL ASSEMBLY.........................................................................................................................................30
1
SAFETY AND PRECAUTIONS
1. FOR SAFE OPERATION
Damage that allows the microwave energy (that cooks or heats the food) to escape will result in poor cooking and may cause serious bodily injury to the operator. IF ANY OF THE FOLLOWING CONDITIONS EXIST, OPERATOR MUST NOT USE THE APPLIANCE. (Only a trained service personnel should make repairs.) (1) A broken door hinge. (2) A broken door viewing screen. (3) A broken front panel, oven cavity. (4) A loosened door lock. (5) A broken door lock. The door gasket plate and oven cavity surface should be kept clean. No grease, soil or spatter should be allowed to build up on these surfaces or inside the oven. DO NOT ATTEMPT TO OPERATE THIS APPLIANCE WITH THE DOOR OPEN. The microwave oven has concealed switches to make sure the power is turned off when the door is opened. Do not attempt to defeat them. DO NOT ATTEMPT TO SERVICE THIS APPLIANCE UNTIL YOU HAVE READ THIS SERVICE MANUAL.
2. FOR SAFE SERVICE PROCEDURES
1. If the oven is operative prior to servicing, a microwave emission check should be performed prior to servicing the oven. 2. If any certified oven unit is found to servicing, a microwave emission check should be performed prior to servicing the oven. (a) inform the manufacturer, importer or assembler, (b) repair the unit at no cost to the owner, (c) attempt to ascertain the cause of the excessive leakage, (d) tell the owner of the unit not to use the unit until the oven has been brought into compliance. 3. If the oven operates with the door open, the service person should tell the user not to operate the oven and contact the manufacturer and CDRH immediately.
IMPORTANT
The wire in this mains lead coloured in accordance with the following code. Green-and-yellow : Each Blue : Neutral Brown : Live As the colours of the wires in the manins lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows. The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked with the letter `E', earth symbol or coloured green-and-yellow. The wire which is coloured blue must be connected to the terminal which is marked with the letter `N' or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter `L' or coloured red.
NOTE
This oven is designed for counter-top use only.
2
SPECIFICATIONS
MODEL POWER SUPPLY POWER CONSUMPTION MICROWAVE GRILL COMBINATION 700W 2450MHz 465 x 279 x 342 mm (18.3 x 11.0 x 13.5 in) 290 x 220 x 306 mm (11.4 x 8.7 x 12.0 in) APPROX. 13 kg (28.7 Ibs.) 59 min. 90 sec. MICROWAVE 10 LEVELS 0.7 Cu. Ft. 800W KOR-63DB9S 1000W KOR-63DB0S 1200W 230V-50Hz, SINGLE PHASE WITH EARTHING
MICROWAVE ENERGY OUTPUT MICROWAVE FREQUENCY OUTSIDE DIMENSIONS (W X H X D) CAVITY DIMENSIONS (W X H X D) NET WEIGHT TIMER FUNCTION SELECTIONS POWER SELECTIONS CAVITY VOLUME
* SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. MODEL POWER SUPPLY POWER CONSUMPTION MICROWAVE GRILL COMBINATION 700W 2450MHz 465 x 279 x 349 mm (18.3 x 11.0 x 13.8 in) 290 x 220 x 306 mm (11.4 x 8.7 x 12.0 in) APPROX. 13 kg (28.7 Ibs.) 59 min. 90 sec. MICROWAVE 10 LEVELS 0.7 Cu. Ft. 800W KOR-63FB9S 1000W KOR-63FB0S 1200W
230V-50Hz, SINGLE PHASE WITH EARTHING
MICROWAVE ENERGY OUTPUT MICROWAVE FREQUENCY OUTSIDE DIMENSIONS (W X H X D) CAVITY DIMENSIONS (W X H X D) NET WEIGHT TIMER FUNCTION SELECTIONS POWER SELECTIONS CAVITY VOLUME
* SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
3
EXTERNAL VIEW
1. OUTER DIMENSION
(1) KOR-63DB9S/63DB0S
(2) KOR-63FB9S/63FB0S
4
2. FEATURE DIAGRAM
1. DOOR SEAL Door seal maintains the microwave within the oven cavity and prevents microwave leakage. 2. DOOR HOOK When the door is closed, it will automatically lock shut. If door is opened while oven is operating, magnetron tube will immediately stop operating. 3. DOOR SCREEN Allows viewing of food. Microwave cannot pass through perforations in screen. 4. SPATTER SHIELD Protects the microwave outlet from splashes of cooking foods. 5. OVEN LAMP Automatically turns on during oven operating. 6. SAFETY INTERLOCK SYSTEM 7. CONTROL PANEL 8. GLASS COOKING TRAY Made of special heat resistant glass. The tray must always be in proper position before operating. Do not cook food directly on the tray. 9. OVEN FRONT PLATE 10. DOOR OPENING BUTTON To open the door push the door opening button. When door is closed, it will automatically lock shut. If door is opened while oven is operating, magnetron tube will immediately stop operating. 11. ROLLER GUIDE Supports the glass cooling tray.
5
3. CONTROL PANEL
1 2 3 5 7 8
M/W DEF. END
POWER
DEFROST
CLOCK
4
AUTO COOK BEVERAGE MORE LESS PASTA
PROZEN PIZZA
6 9 q
10MIN
1HOUR
1 MIN
10MIN
10SEC
1MIN
0
STOP CLEAR
START SPEEDY COOK
11. Display Cooking time, power level, indicators and present time are displayed. 12. Power Used to set power level. 13. Defrost Used to defrost foods. (for time) 14. Clock Used to set clock. 15. Auto cook Used to cook or reheat. 16. One touch Used to cook or reheat specific quantities of food. 17. More Used to add time to cooking. 18. Less Used to remove time from cooking. 19. Time set pad Used to set the cooking time and the present time. 10. Stop/Clear Used to stop the oven operation or to delete the cooking data. 11. Start/Speedy cook Used to start the oven and also used to set a reheat time.
6
INSTALLATION
1. Steady, flat location.
This microwave oven should be set on a steady, flat surface. This microwave oven is designed for counter top use only.
2. Leave space behind and side.
All air vents should be kept a clearance. If all vents are covered during operation, the oven may overheat and, eventually, cause failure.
3. Away from radio, and TV sets
Poor television reception and radio interference may result if the oven is located close to a TV, radio, antenna, or feeder and so on. Position the oven as far from them as possible.
4. Away from heating appliances and water taps
Keep the oven away from hot air, steam or splash when choosing a place to position it, or the insulation might be adversely affected and breakdowns occur.
5. Power supply
· Check your local power source. This microwave oven requires a current of approximately 6 amperes, 230 Volts, 50 Hz. · Power supply cord is about 0.8 meters long. · The voltage used must be the same as specified on this oven. Using a higher voltage may result in a fire or other accident causing oven damage. Using low voltage will cause slow cooking. We are not responsible for damage resulting from use of this oven with a voltage of ampere fuse other than those specified. · This appliance is supplied with cable of special type, which, if damaged, must be repaired with cable of same type. Such a cable can be purchased from DAEWOO and must be installed by a Qualified Person.
6. Examine the oven after unpacking for any damage such as:
A misaligned door, broken door or a dent in cavity. If any of the above are visible, DO NOT INSTALL, and notify dealer immediately.
7. Do not operate the oven if it is colder than room temperature
(This may occur during delivery in cold weather.) Allow the oven to become room temperature before operating.
EARTHING INSTRUCTIONS
This appliance must be earthed. In the event of an electrical short circuit, earthing reduces the risk of the electric shock by providing an escape wire for the electric current. This appliance is equipped with a cord having a earthing plug. The plug must be plugged into an outlet that is properly installed and earthed.
WARNING
Improper use of the earthing plug can result in a risk of electric shock. Consult a qualified electrician or serviceman if the earthing instructions are not completely understood, or if doubt exists as to whether the appliance is properly earthed, and either : If it is necessary to use an extension cord, use only a 3-wire extension cord that has a 3-blade earthing plut, and a 3-slot receptacle that will accept the plug on the appliance. The marked rating of the extension cord should be equal to or greater than the electrical rating of the appliance, or Do not use an extension cord.
7
OPERATIONS AND FUNCTIONS
11. Connect the main lead to an electrical outlet. 12. After placing the food in a suitable container, open the oven door and put it on the glass tray. The glass tray must always be in place during cooking. 13. Close the door securely. 14. When the oven door is opened, the light turns ON. 15. The oven door can be opened at any time during operation. The oven will automatically shut off. To restart the oven, close the door and then touch START. 16. The oven automatically cook on full power unless set to a lower power level. 17. The display will show : 0 when the oven is plugged in. 18. Time clock returns to the present time when the cooking time ends. 19. When the CANCEL button is touched during the oven operatiion, the oven stops cooking and all information retained. To erase all information (except the present time), touch the CANCEL button once more. If the oven door is opened during the oven operation, all information is retained. 10. If the START button is touched and the oven does not operate, check the area between the door and door is closed securely. The oven will not start cooking under the door is completely closed or the program has been reset.
Make sure the oven is properly installed and plugged into the electrical.
Wattage output chart The power level is set by pressing the POWER button. The chart shows the display, the power level and the percentage of power. Touch POWER button Once Twice 3 times 4 times 5 times 6 times 7 times 8 times 9 times 10 times 11 times Power level(Display) P-HI P-90 P-80 P-70 P-60 P-50 P-40 P-30 P-20 P-10 P-00 Approximate Percentage of Power 100% 90% 80% 70% 60% 50% 40% 30% 20% 10% 0%
8
DISASSEMBLY AND ASSEMBLY
Cautions to be observed when trouble shooting.
Unlike many other appliances, the microwave oven is high-voltage, high-current equipment. It is completely safe during normal operation. However, carelessness in servicing the oven can result in an electric shock or possible danger from a short circuit. You are asked to observe the following precautions carefully. 1. Always remove the power plug from the outlet before servicing. 2. Use an insulated screwdriver and ware rubber gloves when servicing the high voltage side. 3. Discharge the high voltage capacitor before touching any oven components or wiring. (1) Check the grounding. Do not operate on a two-wire extension cord. The microwave oven is designed to be used while earthed. It is imperative, therefore, to make sure it is earthed properly before beginning repair work. (2) Warning about the electric charge in the high voltage capacitor. For about 30 seconds after the operation stopped and electric charge remains in the high voltage capacitor. When replacing or checking parts, short between oven chassis and the negative high terminal of the high voltage capacitor by using a properly insulated screwdriver to discharge. 4. When the 15A fuse is blown out due to the operation of the monitor switch; replace primary interlock switch, secondary interlock switch and interlock monitor switch. 5. After repair or replacement of parts, make sure that the screws are properly tightened, and all electrical connections are tightened. 6. Do not operate without cabinet.
CAUTION : Service personnel should remove their watches whenever working close to or replacing the magnetron.
WARNING : When servicing the appliance, need a care of touching or replacing high potential parts because of electrical shock or exposing microwave. These parts are as follows - HV Transformer, Magnetron, HV Capacitor, HV Diode, HV fuse.
9
1. To remove cabinet
1) Remove three screws on cabinet back. 2) Push the cabinet backward.
2. To remove door assembly
1) Remove two screws which secure the stopper hinge top. 2) Remove the door assembly from top plate of cavity. 3) Reverse the above for reassembly.
NOTE : After replacing the door assembly, perform a check of correct alignment with the hinge and cavity front plate.
10
3. To remove door parts.
REF NO. A01
PART CODE 3512203880 3512205200
PART NAME FRAME DOOR FRAME DOOR BARRIER-SCREEN*0 STOPPER SINGE *T AS DOOR WELD AS BARRIER-SCREEN *I GASKET DOOR HOOK SPRING HOOK
DESCRIPTION PP SI83C PP SI83C PET T0.125 KOR-63150S KOR-61150S T0.1 PP POM PW -1
Q'TY 1 1 1 1 1 1 1 1 1
REMARK KOR-63DB KOR-63FB
A02 A03 A04 A05 A06 A07 A08
3517007300 3515204100 3511705500 3517002800 3512300200 3513100700 3515101300
11
(1) Remove the gasket door from door weld as. (2) Remove the door frame from door weld as. (3) Remove the stopper hinge top from door weld as. (4) Remove the spring and the hook. (5) Remove the barrier screen outer from door frame. (6) Reverse the above steps for reassembly.
4. Method to reduce the gap between the door seal and the oven front surface.
(1) To reduce gap located on part `A' Loosen a screws on stopper hinge top, and then push the door to contact the door seal to oven front surface. Tighten two screws. (2) To reduce gap located on part `B' Loosen two screws on stopper hinge under, and then push the door to contact the door seal to oven front surface. Tighten two screws.
NOTE : A small gap may be acceptable if the microwave leakage does not exceed 4mW/cm2.
12
5. To remove control panel parts.
REF NO. B01 B02 B03 B04 B05 B06 B07
PART CODE 3518520960 3518520970 3516725300 3516725350 3514320670 7122401211 3513702710 441G430171 3516906940 3516906950
PART NAME SWITCH MEMBREANE SWITCH MEMBRANE CONTROL PANEL CONTROL PANEL PCB AS SCREW TAPPING LEVER DOOR OPEN SPRING BUTTON BUTTON DOOR OPEN BUTTON DOOR OPEN
DESCRIPTION KOR-63DB9S KOR-63FB9S ABS SG-0760D, SG-175 ABS SG-0760D, SG-175 KOR-63DB9S T2S TRS 4X12 MFZN PP SWP DIA0.7 ABS SG-0760D, SG-175 ABS SG-0760D, SG-175
Q'TY 1 1 1 1 1 3 1 1 1 1
REMARK KOR-63DB KOR-63FB KOR-63DB KOR-63FB
KOR-63DB KOR-63FB
1) Remove the screw which secure the control panel, push up two snap fits and draw forward the control panel assembly. 2) Remove the door open lever from the control panel. 3) Remove four screws which secure the PCB assembly to control panel. 4) Disconnect membrane tail from the connector of the PCB assembly. 5) Detach membrane from the control panel. 6) Remove door open button and button spring from the control panel. 7) Reverse the above steps for reassembly.
13
6. To remove high voltage capacitor.
1) Remove a screw which secure the grounding ring terminal of the H.V. diode and the capacitor holder. 2) Remove the H.V. diode from the capacitor holder. 3) Reverse the above steps for reassembly.
x High voltage circuit wiring
7. To remove magnetron.
1) Remove a screw which secure the magnetron. 2) Remove the magnetron. 3) Reverse the above steps for reassembly.
NOTE : Never install the magnetron without the metallic gasket plate which is packed with each magnetron to prevent microwave leakage. Whenever repair work is carried out on magnetron, check the microwave leakage. It shall not exceed 4mW/cm2 for a fully assembled oven with door normally closed.
14
8. To remove wind guide assembly.
1) Remove a screw for earthing. 2) Remove the noise filter from the wind guide. 3) Remove a screw which secure the wind guide assembly. 4) Draw forward the wind guide assembly. 5) Pull the fan from the motor shaft. 6) Remove two screws which secure the motor shaded pole. 7) Remove the motor shaded pole. 8) Reverse the above steps for reassembly.
9. To remove H.V.transformer.
1) Remove four screws holding the H.V.transformer. 2) Remove the H.V.transformer. 3) Reverse the above steps for reassembly.
15
INTERLOCK MECHANISM AND ADJUSTMENT
The door lock mechanism is a device which has been specially designed to completely eliminate microwave radiation when the door is opened during operation, and thus to perfectly prevent the danger resulting from the leakage of microwave.
(1) Primary interlock switch When the door is closed, the hook locks the oven door. If the door is not closed properly, the oven will not operate. When the door is closed, the hook pushes the button of the microswitch. Then the button of the primary interlock switch bring it under "ON" condition. (2) Secondary interlock switch and interlock monitor switch When the door is closed, the hook pushes the lock lever downward. The lock lever presses the button of the interlock monitor switch to bring it under "NO" condition and presses the button of the secondary interlock switch to bring it under "ON" condition.
ADJUSTMENT : Interlock monitor switch When the door is closed, the interlock monitor switch should be changed(NO condition) before other switches are closed. When the door is opened, the interlock monitor switch should be changed(NC condition) after other switches are opened.
(3) Adjustment steps a) Loosen the two mounting screws. b) Adjust interlock switch assembly position. c) Make sure that lock lever moves smoothly after adjustment is completed. d) Tighten completely two mounting screws.
NOTE : Microwave emission test should be performed after adjusting interlock mechanism. If the microwave smission exceed 4mW/cm2, readjust interlock mechanism.
16
TROUBLE SHOOTING GUIDE
Following the procedure below to check if the oven is defective or not.
1. Check grounding before trouble checking. 2. Be careful of the high voltage circuit. 3. Discharge the high voltage capacitor. 4. When checking the continuity of the switches, fuse or high voltage transformer, disconnect one lead wire from these parts and check continuity with the AC plug removed. To do otherwise may result in a false reading or damage to your meter. NOTE : When electric parts are checked, be sure the power cord is not inserted the wall outlet. Check wire harness, wiring and connected of the terminals and power cord before check the parts listed below.
(TROUBLE 1) Oven does not operate at all ; any inputs can not be accepted.
CONDITION Fuse blows.
CHECK
RESULT
CAUSE Malfunction of interlock monitor switch
REMEDY Replace NOTE 1
Check continuity of interlock monitor switch with door closed
Continuity No Continuity
Check continuity of both primary and secondary interlock switch with door colosed
No Continuity Continuity
Malfunction of interlock switch
Replace NOTE 1
Check continuity of primary interlock switch contact with door partially open until interlock monitor switch contact close (COM NO)
Continuity
Shorted contacts of primary interlock switch.
Replace NOTE 1
Check continuity of primary winding of low voltage transformer
0 or infinite Approx. 150~310 (normal)
Defective low voltage transformer
Replace
Disconnect high voltage fuse and operate the unit
Fuse again blows
Defective low voltage transformer
Replace
17
CONDITION Outlet has proper voltage Fuse does not blow.
CHECK
RESULT No Continuity
CAUSE Defective magnetron
REMEDY Replace
Check continuity of magnetron
Check continuity of noise filter board
No Continuity
Defective magnetron
Replace
Check continuity of power supply cord
No Continuity
Open power supply cord
Replace
Normal
Defective touch control circuit
Replace
NOTE All these switches must be replaced at the same time, please refer to "Interlock Mechanism And Adjustment".
(TROUBLE 2) Display shows all figures selected, but oven does not start cooking, even though desired program and time are set and start button is tapped.
CONDITION Turn table motor and oven lamp do not turn on
CHECK Check continuity of primary interlock switch
RESULT No Continuity
CAUSE Malfunction of primary interlock switch
REMEDY Adjust or replace
Check continuity of secondary interlock switch
No Continuity
Malfunction of secondary interlock switch
Adjust or replace
Check D.C. voltage being supplied to RELAY (RY2) coil
0V
Defective touch control circuit
Replace
Approx. 12 VDC
Faulty contacts of RELAY (RY2) or open relay coil
Replace
18
(TROUBLE 3)
No microwave oscillation even though fan motor rotates.
CONDITION No microwave oscillation
CHECK
RESULT Continuity
CAUSE
REMEDY
Check continuity of high voltage fuse Replace high voltage fuse
Check continuity of high voltage capacitor terminals with wires removed
Continuity
Defective high voltage transformer
Replace
Check continuity of high voltage rectifier in forward and backward direction with DC megger
Continuity in backward direction Continuity
Defective high voltage rectifier
Replace
Connect megger leads to magnetron terminal and magnetron body
Defective magnetron
Replace
Check resistance of primary and secondary coil of high voltage transformer
0 or
Defective high voltage transformer
Replace
Check continuity of magnetron with wires removed
No Continuity
Defective magnetron
Replace
Check continuity of filament terminal of high voltage transformer
No Continuity
Defective high voltage transformer
Replace
0V Check D.C. voltage being supplied to RELAY (RY1) coil Defective touch control circuit
Replace
Approx 15 VDC
Faulty contacts or RELAY (RY1) or open relay coil
Replace
19
(TROUBLE 4)
The following visual conditions indicate a probable defective touch control circuit or membrane switch assembly.
11. Incomplete segments (1) Segments missing (2) Partical segments missing (3) Digit flickering other than normal display slight flickering (4) " :0" does not display when power is on. 12. A distinct changes in the display are not on when they should be. 13. One or more digits in the display are not on when they should be. 14. Display indicates a number different from one touched. 15. Specific numbers (for example 2 or 3) will not display when the button is touched. 16. Display does not count down or up with time cooking or clock operation. 17. Oven is programable and cooks normally but no display shows. 18. Display obviously jumps in time while counting down. 19. Display counts down noticeably too fast while cooking. 10. Display does not show the time of day when cancel button is touched. 11. Oven lamp and turntable motor do not stop although cooking is finished. Check if the RELAY 2 contacts close if they are close, replace touch control circuit.
CONDITION Display does not show programming at all, even if keyboard is touched.
CHECK Check rach pad for continuity of the membrane keyboard for the following keyboard check procedure
RESULT Normal
CAUSE Malfunction of touch control circuit of control box sub-assembly Malfunction of the membrane keyboard
REMEDY Replace control box subassembly
Abnormal
Replace the membrane keyboard
NOTE Before following the particular steps listed above in the trouble shooting guide for the membrane keyboard's, failure, please check for the continuity of each wire-harness between the membrane keyboard and P.C.B. assembly.
20
MEASUREMENT AND TEST
1. MEASUREMENT OF THE MICROWAVE POWER OUTPUT
Microwave output power can be checked by indirectly measuring the temperature rise of a certain amount of water exposed to the microwave as directed below. PROCEDURE 1. Microwave power output measurement is made with the microwave oven supplied at rated voltage and operated at its maximum microwave power setting with a load of 1000±5cc of potable water. 2. The water is contained in a cylindrical borosilicate glass vessel having a maximum material thickness of 3 mm and an outside diameter of approximately 190 mm. 3. The oven and the empty vessel are at ambient temperature prior to the start of the test. The initial temperature of the water is 10±2°C (50±3.6°F) It is measured immediately before the water is added to the vessel. After addition of the water to the vessel, the load is immediately placed on the center of the shelf, which is in the lowest normal position. 4. Microwave power is switched on. 5. Heating time should be exactly A seconds. (Refer to table as following) Heating time is measured while the microwave generator is operating at full power. The filament heat-up time for magnetron is not included. 6. The initial and final temperature of water is selected so that the maximum difference between the ambient and final water temperature is 5K. 7. The microwave power output P in watts is calculated from the following formula : P=4187 X vT/t · vT is difference between initial and ending temperature. · It is the heating time. The power measured should be B (Refer to SPECIFICATIONS)W±10.0%.
CAUTION : 1. Water load should be measured exactly to 1 liters. 2. Input power voltage should be exactly specified voltage(Refer to SPECIFICATIONS). 3. Ambient temperature should be 20±2°C(68±3.6°F)
Heating time for power output: A(second) B(W) 70 600 64 650 60 700 56 750 52 800 49 850 47 900 44 950 42 1000 40 1050 38 1100
21
2. MICROWAVE RADIATION TEST
CAUTION : 1. Make sure to check the microwave leakage before and after repair of adjustment. 2. Always start measuring of an unknown field to assure safety for operating personnel from microwave energy. 3. Do not place your hands into any suspected microwave radiation field unless the safe density level is known. 4. Care should be taken not to place the eyes in direct line with the source of microwave energy. 5. Slowly approach the unit under test until the radiometer reads an appreciable microwave leakage from the unit under the test.
PROCEDURES 1. Prepare Microwave Energy Survey Meter, 600cc glass beaker, and glass thermometer 100°C(212°F). 2. Pour 275cc±15cc of tap water initially at 20±5°C(68±9°F) in the 600cc glass beaker with an inside diameter of approx. 95mm(3.5in.). 3. Place it at the center of the tray and set it in a cavity. 4. Close the door and operate the oven. 5. Measure the leakage by using Microwave Energy Survey Meter with dual ranges, set to 2450MHz. 1) Measured radiation leakage must not exceed the value prescribed below. Leakage for a fully assembled oven with door normally closed must be less than 4mW/cm2. 2) When measuring the leakage, always use the 5cm(2in.) space cone with probe. Hold the probe perpendicular to the cabinet and door. Place the space cone of the probe on the door, cabinet, door seem, door viewing screen, the exhaust air vents and the suction air vents. 3) Measuring should be in a counter-clockwise direction at a rate of 1 in./sec. If the leakage of the cabinet door seem is unknown, move the probe more slowly. 4) When measuring near a corner of the door, keep the probe perpendicular to the areas making sure the probe end at the base of the cone does not get closer than 2 in. from any metal. If it does not, erroneous reading may result.
22
3. COMPONENT TEST PROCEDURE
· High voltage is present at the high voltage terminal of the high voltage transformer during any cooking cycle. · It is neither necessary nor advisable to attempt measurement of the high voltage. · Before touching any oven components or wiring, always unplug the oven from its power source and discharge the capacitor.
1. High voltage transformer
(1) Remove connections from the transformer terminals and check continuity. (2) Normal readings should be as follows: Secondary winding ...................Approx. 140±10% Filament winding....................................Approx. 0 Primary winding .....................................Approx. 2
2. High voltage capacitor
(1) Check continuity of capacitor with meter on the highest OHM scale. (2) A normal capacitor will show continuity for a short time, and then indicate 10M once the capacitor is charged. (3) A shorted capacitor will show continuous continuity. (4) An open capacitor will show constant 10M. (5) Resistance between each terminal and chassis should be infinite.
3. High voltage diode
(1) Isolate the diode from the circuit by disconnecting the leads. (2) With the ohmmeter set on the highest resistance scale measure the resistance across the diode terminals. Reverse the meter leads and again observe the resistance reading. Meter with 6V, 9V or higher voltage batteries should be used to check the front-back resistance of the diode, otherwise an infinite resistance may be read in both directions. A normal diode's resistance will be infinite in one direction and several hundred K in the other direction.
4. Magnetron
For complete magnetron diagnosis, refer to "Measurement of the Microwave Power Output". Continuity checks can only indicate and open filament or a shorted magnetron. To diagnose for an open filament or a shorted magnetron. (1) Isolate magnetron from the circuit by disconnecting the leads. (2) A continuity check across magnetron filament terminals should indicate 0.1 or less. (3) A continuity check between each filament terminal and magnetron case should read open.
5. Fuse
If the fuse in the primary and monitor switch circuit is blown when the door is opened, check the primary and monitor switch before replacing the blown fuse. In case the fuse is blown by an improper switch operation, replace the defective switch and fuse at the same time. Replace just the fuse if the switches operate normally.
23
WIRING DIAGRAM
24
PRINTED CIRCUIT BOARD
1. CIRCUIT CHECK PROCEDURE 1. Low Voltage Transformer check
· The low voltage transformer is located on the P.C.B. · Measuring condition: input voltage : 230V/Frequency : 50Hz Terminal Voltage 4-8 LOAD AC 25.8 V NO LOAD AC 31.8 V
NOTE : 1. Refer to Circuit Diagram (point 4). 2. Secondary side voltage of the low voltage transformer changes in proportion to fluctuation of power source voltage. 3. The allowable tolerance of the secondary voltage is within ± 5% of nominal voltage.
2. Voltage check
· Key check point NO 1 2 CHECK POINT IC 1 PIN 14 IC 1 PIN 22
T:20ms(50Hz)
REMARK -5 VDC
3
IC 1 PIN 1 OR 2
T:250ns(4MHz)
· Check method NO 1 2 MEASURE POINT MP1 MP2 WAVE FORM DC -5V±0.25V DC -12V±2.0V REMEDY Replace VL1, EC1 Replace EC2, D9, 10, 11 REMARK NO LOAD NO LOAD
NOTE : Each measure point must be measured with GND points.
25
MP1
MP2
Measure Point
26
3. When there is no microwave oscillation
1) When touching START pad, oven lamp does not turn on. Fan motor does not rotate, but cook indicator in display comes on. * Cause : RELAY 2 does not operate. ¡ refer to Circuit Diagram (Point 3) - Check method STATE RELAY 2 ON RELAY 2 OFF POINT A -5VDC GND B GND -12VDC
2) When touching START pad, oven lamp turns on. Fan motor and turntable rotate and cook indicator in display comes on. * Cause : RELAY 1 does not operate. ¡ refer to Circuit Diagram (Point 2) - Check method STATE RELAY 1 ON RELAY 1 OFF POINT A -5VDC GND B GND -12VDC
4. When the door is opened during operation, the count down timer does not stop.
¡ refer to Circuit Diagram (Point 1) -Check method STATE 1) DOOR OPEN 2) DOOR CLOSED CHECK NO 1 METHOD Check the stage (ON, OFF) of the door open monitor switch by resistance measurement. POINT A OPEN CLOSE B -5VDC GND REMEDY Replace door open monitor switch.
5. When the digital clock does not operate properly.
¡ refer to Circuit Diagram (Point 5) POINT A
T:20ms(50Hz)
WAVE FORM
* If clock does not keep exact time, you must check resistor R23, 24 zener diode ZD2.
27
2. PCB CIRCUIT DIAGRAM
28
3. P.C.B. LOCATION NO.
1) KOR-63DB9S/KOR-63FB9S NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 NAME CAPACTIOR ELEC CAPACTIOR ELEC CONNECTOR WAFER CONNECTOR FILM CONNECTOR WAFER DIODE RECTIFY DIODE RECTIFY DIODE ZENER DIODE ZENER LED DISPLAY PCB MAIN C ARRAY R ARRAY REGISTER REGISTER REGISTER REGISTER REGISTER REGISTER REGISTER REGISTER RESONATOR CERAMIC IC REGULATOR TRANSISTOR TRANSISTOR TRANS POWER WIRE COPPER WIRE COPPER IC MICOM SW RELAY SW RELAY CAPACITOR CERA EC1 EC2 CN1 CN2 CN3 D1~9 D10, D11 ZD1 ZD2 DP1 M171 CA1 RA1 R1, R2, R5~R9 R4, R14, R20 R3 R15, R16 R21 R10~13, R19, R23~24 R17 R22 CR1 VL1 Q1~7 Q9 LVT J2~J4, J8~J10, SJ2 J1, J5, J6, J11 IC1 RY1 RY2 C1~6 SYMBOL SPECIFICATION 16V RS 100MF 25V RSS 1000MF YW396-02V FCZ 254-10P YW396-05AV 1N4148 KN4004A UZ- 3.3BSB 1/2W UZ- 5.1BSB 1/2W DDRG-63DB 81.5X139.9 5102M 6P(5) 1/8 100K J 1/6W 330 5% 1/6W 1K 5% 1/6W 4.7K 5% 1/6W 100K 5% 1/6W 100 5% 1/6W 10K 5% 1/6 1M 5% 1/4W 51 5% 4.00MTS MC7905C KRA-106M KTA-1266Y DMR-63KFS(35X11) 1/0.52 TIN COATING(7.5MM) 1/0.52 TIN COATING(10MM) TMP47C443N-1D99 G5G-1A-1C-12V OJ-SS-112LM 104 50V Z AXIAL PART CODE CEXF1C101V CEXF1E102V 351915020 441M367150 3519150510 DZN4148--DZN4004A-DZUZ3R3BSB DZUZ5R1BSB DDDRG63DB3514324000 CN5XB-102M RA-86X104J RD-AZ331JRD-AZ102JRD-AZ472JRD-AZ104JRD-AZ101JRD-AZ103JRD-AZ105JRD-4Z510J5P4R00MTS1MC7905C-TZRA106M-TZTA1226Y5EPV035306 85801052GY 85801052GY 13GS63DB00 5SC0101121 5SC0101404 CCZF1H104Z Q'TY 1 1 1 1 1 9 2 1 1 1 1 1 1 7 3 1 2 1 7 1 1 1 1 7 1 1 7 4 1 1 1 6
29
EXPLODED VIEW AND PARTS LIST
1. DOOR ASSEMBLY Refer to Disassembly and assembly. 2. CONTROL PANEL ASSEMBLY Refer to Disassembly and assembly. 3. TOTAL ASSEMBLY
30
NO A00 B00 F01 F02 F03 F04 F05 F06 F07 F08 F09 F10 F11 F12 F13 F14 F15 F16 F17 F18 F19 F20 F21 F22
PART CODE 3511714420 3511714450 3516720620 3516720640 3510805000 7112401011 3516109000 3516109600 7112401011 7122401211 7122401211 7112401011 35113AEQ0D 7112401011 7122401211 4415D67620 4415D67120 3518606200 7121403011 3963512310 3512517000 3511800300 3518002400 3516004000 7S422X4081 3513003200 3518302200 3518400900 3518401000
PART NAME DOOR AS DOOR AS CONTROL-PANEL AS CONTROL-PANEL AS CABINET SCREW TAPPING CAVITY WELD AS CAVITY JOINT AS SCREW TAPPING SCREW TAPPING SCREW TAPPING SCREW TAPPING CORD POWER AS SCREW TAPPING SCREW TAPPING FUSE FUSE NOISE-FILTER SCREW TAPPING MOTOR SHADED POLE GUIDE WIND FAN MAGNETRON SPECIAL SCREW SCREW SPECIAL HOLDER HV CAPACITOR CAPACITOR HV DIODE HV AS DIODE HV AS
DESCRIPTION KOR-63D59A KOR-63F59A KOR-63DB9S KOR-63FB9S SECC T0.5 T1 TRS 4*10 MFZN CAVITY WELD AS KOR-63150S T1 TRS 4*10 MFZN T2S TRS 4*12 MFZN T2S TRS 4*12 MFZN T1 TRS 4*10 MFZN 3X0.75 70X70 100-RTML T1 TRS 4*10 MFZN T2S TRS 4*12 MFZN 250V 12A 65TS 250V 12A MDA DWLF-M12 T2S PAN 4X30 MFZN 230V 20W MW10CA-M02 PP PP+30%GLASS 2M218J(F) T2 BOLT FLANGE 5X12 DACRO TT2 TRS 4X8 SE MFZN SECC T0.6 2100VAC 0.98µF #187 HVR-1X-30B #187 ESJC13-12BX #187
Q'TY 1 1 1 1 1 3 1 1 1 1 1 2 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1
31
NO F23 F24 F25 F26 F27 F28 F29 F30 F31 F32 F33 F34 F35 F36 F37 F38 F39 F40 F41 F42 F43 F44 F45 F46 F47 F48 F49 F50
PART CODE 3518701100 3518113751 3518113701 3516003700 3510311710 7112401011 3512100900 7S422X4081 3515201101 4415A17352 4415A66910 4415A17352 3513702600 3513811730 3513811700 3518571000 3513601600 3512715000 7121400611 3966310100 3518905300 3513003400 3516003700 3511406220 3517400620 3514700710 3512517300 3517203600 7122401211 3518570400
PART NAME FUSE HV TRANS HV TRANS HV SPECIAL SCREW BASE SCREW TAPPING FOOT SCREW SPECIAL STOPPER HINGE *U SW MICRO SW MICRO SW MICRO LEVER LOCK LOCK LOCK SWITCH PUSH LAMP HARNESS MAIN SCREW TAPPING MOTOR SYNCRO THERMOSTAT HOLDER THERMOSTAT SPECIAL SCREW COVER WAVE GUIDE COUPLER ROLLER GUIDE ROLLER TRAY SCREW TAPPING SWITCH S/A RELAY
DESCRIPTION 5KV 0.55A HV-41A55-02 TM-N70S0-63T (KOR-63DB9S/63FB9S) DY-N80S0-63T (KOR-63DB0S/63FB0S) TT3 HEX 4X8 FLG MFZN SECC T0.6 T1 TRS 4*10 MFZN PP DASF-130 TT2 TRS 4X8 SE MFZN SCP-1 T2.5 VP-533A-OF SPNO #187 200G VP-531A-OF/SZM-V16-FA-61 VP-533A-OF SPNO #187 200G POM POM NATURAL (KOR-63DB) POM BLACK (KOR-63FB) MP101C BL 240V 25W T25 C7A H187 KOR-631G0S T2S PAN 4X6 MFZN 220V 2.5W GM-16-24FD12 OFF:75 ON:65 H #187 NB PBT TT3 HEX 4X8 FLG MFZN PP J640A XAREC TEFLON PP 5113MF6 A353B GLASS T2S TRS 4*12 MFZN DWSR-1
Q'TY 1 1 1 4 1 5 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 3 1 1 1 1
32
DAEWOO ELECTRONICS CO., LTD.
686, AHYEON-DONG MAPO-GU SEOUL, KOREA C.P.O. BOX 8003 SEOUL, KOREA TELEX: DWELEC K28177-8 CABLE: "DAEWOOELEC"
S/M NO. : R63DB9S002
PRINTED DATE: Jul. 2001