Make | Model | Problem | Solution | Date |
| | | |
Found: 26
|
Beko | 12220 | Blank screen with buzzing & Thy overheats | R725 hi res | 14-09-04 |
Beko | 12220 | Col int | Dec panel plugs int | 14-09-04 |
Beko | 12220 | Int pic/sound - disappears with flashing on screen and noise thro speaker | Xtal Q701 in front of IC701 | 14-09-04 |
Beko | 12220 | Top ? of screen lit, rest blanked | R717 1M o/c also check R722 1M | 14-09-04 |
Beko | 12220 | Top quarter of screen lit & blank - rest black | R717 1M o/c - connected to pin 5 TEA2029 also check R722 in series 1M | 14-09-04 |
Beko | 12220 | Trips off at sw on - HT = 125v on bulb | D801 BY299 s/c - LOPTX could be the cause | 14-09-04 |
Beko | 12220 10.2 | Front cont int don't work | Check momentary contacts on mains sw | 14-09-04 |
Beko | 12220NX | Status info perm/semi perm displayed | Q2 17.47 Mhz Xtal on audio pcb drifting | 14-09-04 |
Beko | 12220NX | The status information appeared on the scrcen at r | The cause of the fault was on the audio panel , where the 17.47MHz crystal Q2 was drifting when warm.§ | 14-09-04 |
Beko | 12220T | Dead 55v HT | D111 FR30-02 S/C, U4 supply diode | 14-09-04 |
|
Goldstar | CBZ9222E | No horizontal sync. when cold. When hot, everything is OK. It was not possible to track the defective component with a freezer spray. | Changed several caps around TDA2579 chip. | 14-09-04 |
Goldstar | CBZ9222E | No horizontal sync. when cold. When hot, everything is OK. It was not possible to track the defective component with a freezer spray. | Changed several caps around TDA2579 chip. | 14-09-04 |
Mitsubishi | CT2223B | FIELD BOUNCE or collapse | C412 C413 330mfd | 14-09-04 |
Mitsubishi | CT2227 | Dead - chan display & relay click only | Dry joints T571 | 14-09-04 |
Mitsubishi | CT2227BM | Dead - int dead | Dry-joints on line driver transformer | 14-09-04 |
Mitsubishi | CT2227BM | field collapse with burning smell | C412 330µ and C413 | 14-09-04 |
Mitsubishi | CT2227BM | No sound or raster. | R7A0 ( 1.2ohm ) o/c on remote panel. | 14-09-04 |
Mitsubishi | CT2227BM | Reduced height. | Dry-joints on line driver transformer | 14-09-04 |
Mitsubishi | CT2227BM | Standby - switching to standby. | IC7A0 ( M50124P ) | 14-09-04 |
Mitsubishi | CT2227M | St/by only - no relay op | R7A0 1R2 1/2w | 14-09-04 |
Schneider | Euro70222 | Dead | Line dr tr s/c & R306 burnt | 14-09-04 |
Toshiba | 2226 | No line sync. | R402 ( 15k ) o/c. | 14-09-04 |
TOSHIBA | 2226 | SET SPRINGS TO LIFE AFTER BEING STUCK ON STANDBY | REPLACE C932 100MFD25V | 14-09-04 |
Toshiba | C2220 | Arcing sound with black lines on screen | Seen in dark arcing from LOP heatsinj screw - tightened screw | 14-09-04 |
Toshiba | C2220 | Severe lack of height when cold | C317 2µ2 50v | 14-09-04 |
Toshiba | C2226B1 | Field non lin | C316 470µ | 14-09-04 |