| Make | Model | Problem | Solution | Date |
| | | |
| Found: 107
|
| Finlux | 100 | Dead | Du20 BY229 dry | 14-09-04 |
| Finlux | 1000 | Blue picture. | R647 ( 1k8 ) high. | 14-09-04 |
| Finlux | 1000 | Channel - random channel display. | LOPTX | 14-09-04 |
| Finlux | 1000 | Comes on with red/green/blue raster in turn | Cb38 10µ 63v | 14-09-04 |
| Finlux | 1000 | Dead | Du20 BY299 in 17.5v supply dry joints | 14-09-04 |
| Finlux | 1000 | Dead | Dry joints PTCu2 or Ru3/4/6/7 o/c | 14-09-04 |
| Finlux | 1000 | Dead | RU42 & 43 15R burning - LOPTx faulty | 14-09-04 |
| Finlux | 1000 | Dead - blowing 1.25A fuse - intermittently. | Check for dry joint on LU3. | 14-09-04 |
| Finlux | 1000 | Dead - blown 1.25A fuse | Check for dry joints at Lu3 | 14-09-04 |
| Finlux | 1000 | Dead with Ru14 10k burning up | Chopper tfmr (same type as 3000) | 14-09-04 |
|
|
| Finlux | 1000 | Dead. | Du20 ( BY299 ) s/c , 138v ht rectifierDu16 | 14-09-04 |
| Finlux | 1000 | Going off just after switching on. | LOPTX | 14-09-04 |
| Finlux | 1000 | INT COLOUR , SEEMS LIKE DRY JOINTS | Ct12 REF OSC TRIMMER NOISY . LINK PINS 25 , 26 AND 1 , 5 TO SETUP | 14-09-04 |
| Finlux | 1000 | int st/by | lopt has hole in it | 14-09-04 |
| Finlux | 1000 | Int various inc red/green/off/false line lock/line tearing | 12v supply low due to Ta8 BD241 - also check Da1 | 14-09-04 |
| Finlux | 1000 | No picture or sound - EHT ok. | Ri20 ( 100R ) o/c. | 14-09-04 |
| Finlux | 1000 | No sound & sw to st/by aft 10 mins (no sync) | Check pin 13 ICh1 TDA2578A TB chip should be high - was only 0.5v (transmit ident) - chip faulty | 14-09-04 |
| Finlux | 1000 | No sound or pic - line drive missing | Ta2 BC547 | 14-09-04 |
| Finlux | 1000 | NO SOUND OR PICTURE | NO LINE DRIVE Ta2 BC547 OC | 14-09-04 |
| Finlux | 1000 | No sound or picture - EHT ok. | Ri20 ( 100R ) o/c. | 14-09-04 |
| Finlux | 1000 | Raster - white. | DA1 ( IN4007 ) on vision IF. | 14-09-04 |
| Finlux | 1000 | Standby - going into standby intermittently. | DA1 ( IN4007 ) in vision IF. | 14-09-04 |
| Finlux | 1000 | This set would start off all right. But after abou | Ch11 ( 47uF , 63V ) | 14-09-04 |
| Finlux | 1000 (early) | Int col with TDA3652A chip | ref osc trimmer Ct12 6-30pf noisy. To set up link pins 24/25 & 1/5 of ic & adj Ct12 for stationary col | 14-09-04 |
| Finlux | 1000 early | No pic - crt htrs alight | Cb 2µ2 35v o/c (near col dec chip) | 14-09-04 |
| Finlux | 1000 srs EARLY | INT COLOUR , SEEMS LIKE DRY JOINTS | Ct12 REF OSC TRIMMER NOISY . LINK PINS 25 , 26 AND 1 , 5 TO SETUP | 14-09-04 |
| Finlux | 1000/3000 | Dead | BY299 17v rect or Du16 138v HT rect | 14-09-04 |
| Finlux | 1101 | Flashing/flickering | Dry joints link thro conns on txt pcb | 14-09-04 |
| Finlux | 1101 | Flicker - pull at top - varying contrast. | Drys on through-board link pins on text PCB. | 14-09-04 |
| Finlux | 1111W | Dead; High HT; lack of height | HT was 166v (138v) due to set ht pot faulty also check Cap 1µ 63v in chopper feedback cct | 14-09-04 |