Samsung WS32W6HA free download

File name WS32W6HAX_XEC.ES030.1.01.pdf

COLOR TELEVISION RECEIVER Chassis : Model : SCT53A WS32W6HA WS28W6HA COLOR TELEVISION RECEIVER CONTENTS 1. Precautions 2. Reference Information 3. Specifications 4. Disassembly and Reassembly 5. Alignment and Adjustments 6. Troubleshooting 7. Exploded View and Parts List 8. Electric Parts List 9. Block Diagrams 10. Wiring Diagram 11. Schematic Diagrams ELECTRONICS © Samsung Electronics Co., Ltd. JUL.1999 Printed in Korea 3SCT53A-3201

File name WS32W6HAX_XEC.ES030.1.02.pdf

Precautions 1. Precautions Follow these safety, servicing and ESD precautions to prevent damage and protect against potential hazards such as electrical shock and X-rays. 1-1 Safety Precautions 1. Be sure that all of the built-in protective devices are replaced. Restore any missing protective shields. 2. When reinstalling the chassis and its assemblies, be sure to restore all protective devices, including: nonmetallic control knobs and compartment covers. 3. Make sure that there are no cabinet openings through which peopleСparticularly childrenСmight insert fingers and contact dangerous voltages. Such openings include the spacing between the picture tube and the cabinet mask, excessively wide cabinet ventilation slots, and improperly fitted back covers. If the measured resistance is less than 1.0 megohm or greater than 5.2 megohms, an abnormality exists that must be corrected before the unit is returned to the customer. 4. Leakage Current Hot Check (Figure 1-1): Warning: Do not use an isolation transformer during this test. Use a leakagecurrent tester or a metering system that complies with American National Standards Institute (ANIS C101.1, Leakage Current for Appliances), and Underwriters Laboratories (UL Publication UL1410, 59.7). 5. With the unit completely reassembled, plug the AC line cord directly into the power outlet. With the unitХs AC switch first in the ON position and then OFF, measure the current between a known earth ground (metal water pipe, conduit, etc.) and all exposed metal parts, including: antennas, handle brackets, metal cabinets, screwheads and control shafts. The current measured should not exceed 0.5 milliamp. Reverse the powerplug prongs in the AC outlet and repeat the test. DEVICE UNDER TEST TEST ALL EXPOSED METAL SURFACES 2-WIRE CORD ALSO TEST WITH PLUG REVERSED (USING AC ADAPTER PLUG AS REQUIRED) LEAKAGE CURRENT TESTER (READING SHOULD NOT BE ABOVE 0.5mA) EARTH GROUND Fig. 1-1 AC Leakage Test 6. Antenna Cold Check: With the unitХs AC plug disconnected from the AC source, connect an electrical jumper across the two AC prongs. Connect one lead of the ohmmeter to an AC prong. Connect the other lead to the coaxial connector. 7. X-ray Limits: The picture tube is especially designed to prohibit X-ray emissions. To ensure continued X-ray protection, replace the picture tube only with one that is the same type as the original. Carefully reinstall the picture tube shields and mounting hardware; these also provide X-ray protection. 8. High Voltage Limits: High voltage must be measured each time servicing is done on the B+, horizontal deflection or high voltage circuits. Correct operation of the X-ray protection circuits must be reconfirmed whenever they are serviced. (X-ray protection circuits also may be called Тhorizontal disableУ or Тhold-downУ.) Heed the high voltage limits. These include the XРray Protection Specifications Label, and the Product Safety and X-ray Warning Note on the service data schematic. Samsung E

File name WS32W6HAX_XEC.ES030.1.03.pdf

Reference Information 2. Reference Information 2-1 Tables of Abbreviations and Acronyms Table 2-1 Abbreviations A Ah Е dB dBm °C °F °K F G GHz g H Hz h ips kWh kg kHz k km km/h kV kVA kW I MHz Ampere Ampere-hour Angstrom Decibel Decibel Referenced to One Milliwatt Degree Celsius Degree Fahrenheit degree Kelvin Farad Gauss Gigahertz Gram Henry Hertz Hour Inches Per Second Kilowatt-hour Kilogram Kilohertz Kilohm Kilometer Kilometer Per Hour Kilovolt Kilovolt-ampere Kilowatt Liter Megahertz MV MW M m µA µF µH µm µs µW mA mg mH mI mm ms mV nF pF Ib rpm rps s V VA W Wh Megavolt Megawatt Megohm Meter Microampere Microfarad Microhenry Micrometer Microsecond Microwatt Milliampere Milligram Millihenry Milliliter Millimeter Millisecond Millivolt Nanofarad Ohm Picofarad Pound Revolutions Per Minute Revolutions Per Second Second (Time) Volt Volt-ampere Watt Watt-hour Samsung Electronics 2-1 Reference Information Table 2-1 Abbreviations ABL AC ACC AF AFC AFT AGC AM ANSI APC APC A/V AVC BAL BPF B-Y CATV CB CCD CCTV Ch CRT CW DC DVM EIA ESD ESD FBP FBT FF FM FS GND G-Y H HF HI-FI IC IC IF Automatic Brightness Limiter Alternating Current Automatic Chroma Control Audio Frequency Automatic Frequency Control Automatic Fine Tuning Automatic Gain Control Amplitude Modulation American National Standards Institute Automatic Phase Control Automatic Picture Control Audio-Video Automatic Volume Control Balance Bandpass Filter Blue-Y Community Antenna Television (Cable TV) Citizens Band Charge Coupled Device Closed Circuit Television Channel Cathode Ray Tube Continuous Wave Direct Current Digital Volt Meter Electronics Industries Association Electrostatic Discharge Electrostatically Sensitive Device Feedback Pulse Flyback Transformer Flip-Flop Frequency Modulation Fail Safe Ground Green-Y High High-Frequency High Fidelity Inductance-Capacitance Integrated Circuit Intermediate Frequency I/O L L LED LF MOSFET MTS NAB NEC NTSC OSD PCB PLL PWM QIF R RC RF R-Y SAP SAW SIF SMPS S/N SW TP TTL TV UHF UL UV VCD VCO VCXO VHF VIF VR VTR VTVM TR Input/output Left Low Light Emitting Diode Low Frequency Metal-Oxide-Semiconductor-Field-Effect-Tr Multi-channel Television Sound National Association of Broadcasters National Electric Code National Television Systems Committee On Screen Display Printed Circuit Board Phase-Locked Loop Pulse Width Modulation Quadrature Intermediate Frequency Right Resistor & Capacitor Radio Frequency Red-Y Second Audio Program Surface Acoustic Wave(Filter) Sound Intermediate Frequency Switching Mode Power Supply Signal/Noise Switch Test Point Transistor Transistor Logic Television Ultra High Frequency Underwriters Laboratories Ultraviolet Variable-Capacitance Diode Voltage Controlled Oscillator Voltage Controlled Crystal Oscillator Very High Frequency Video Intermediate Frequency Variable Resistor Video Tape Recorder Vacuum Tube Voltmeter Transistor 2-2 Samsung Electronics Reference Information 2-3 IC Line Up Table 2-1 IC Line Up Loc No. IC101 IC201

File name WS32W6HAX_XEC.ES030.1.04.pdf

Specifications 3. Specifications MODEL 100 Hz MAIN CHARACTERISTICS Dolby Pro Logic EPG AV_LINK TUNING SYSTEM COLOR SOUND ANTENNA INPUT CONSUMPTION REQUIREMENTS POWER FREQUENCY TUBE SIZE TYPE NUMBER OF CHANNELS TUNING RANGE 180W Main Voltage : 230V Input Range : 220-240V 50Hz/60Hz 30" (76Cm) 12.8:9, 2.5R Invar 100 VHF: 2 ~ 12, UHF : 21 ~ 69, Cable : S1 ~ S41 Right : 15W Left : 15W Center : 15W Surround : 15W (L+R) - RCA : Input/S-VHS FRONT - Headphone Audio Output CW-30A80SA (CW764AHA) O O O O Frequency Synthesizer PAL, SECAM, NTSC(only AV mode) NICAM, A2 STEREO, AM 75ohms,Coaxial Cable CW-30A90SD (CW764AHD) O X - SOUND OUTPUT Right : 15W Left : 15W SOCKETS - EXT1 : full RGB Scart / AV-LINK - EXT2 : Scart (Output Selectable) BACK (3 SCARTS) - EXT3 : Decoder (Output Selectable) - Surround SPK Jack - Rear AMP Jack Specifications are subject to change. Samsung Electronics 3-1 Specifications 3-1 3D Sound Option Table (Main Board) Loc No. C601 C602 C612 C613 C614 C615 C616 C617 C618 C619 C620 C635 CN17 IC602 IC604 J013 J168 J169 R610 R611 R613 R614 R615 R616 R617 R618 R619 R620 R629 J061 J062 JUMPER JUMPER CW-30A80A : 3D SOUND SPECIFICATION DEL DEL DEL DEL DEL DEL DEL DEL DEL DEL DEL DEL DEL DEL DEL DEL DEL DEL DEL DEL DEL DEL DEL DEL DEL DEL DEL DEL DEL 3812-000219 3812-000219 CODE NO CW-30A90SD : DOLBY SOUND SPECIFICATION C-FILM 103 C-FILM 103 C-AL 1000 mF C-FILM 104 C-AL 1000mF C-FILM 104 C-FILM 104 C-AL 1000mF C-AL 1 mF C-AL 100mF C-AL 1mF C-AL 10 mF 3P IC;TDA7265 IC;4053B JUMPER JUMPER JUMPER 1/2 1.8K 1/2 1.8K 1/2 1.8K 1/2 1.8K 1/2 4.7 1/8 10K 1/8 300 1/8 300 JUMPER JUMPER 1/8 10K DEL DEL CODE NO 2301-000380 2301-000380 2401-000192 2301-000530 2401-000192 2301-000530 2301-000530 2401-000192 2401-000603 2401-000318 2401-000603 2401-002265 3711-000900 AA96-50279A 0801-000961 3812-000219 3812-000219 3812-000219 2001-001055 2001-001055 2001-001055 2001-001055 2001-001146 2001-000290 2001-000628 2001-000628 3812-000219 3812-000219 2001-000290 3-2 Samsung Electronics Specifications 3-2 3D Sound Option Table (AV-Terminal Board) Loc No. CN706 CN707 RCA-5P 3722-001157 CW-30A80A : 3D SOUND SPECIFICATION CODE NO CW-30A90SD : DOLBY SOUND SPECIFICATION 4P, JACK RCA-2P CODE NO AA63-40276A 3722-001158 Samsung Electronics 3-3

File name WS32W6HAX_XEC.ES030.1.06.pdf

Disassembly and Reassembly 4. Disassembly and Reassembly 4-1 Back Cover Removal 1. After removing the 7 screws, pull the cabinet backwards. 1 7 6 2 3 5 4 4-2 Speaker Removal 1. Loosen the 4 screws and remove the Speaker Holders. Samsung Electronics 4-1 Disassembly and Reassembly 4-3 CRT Removal 1. Spread a soft mat on the floor. Place the TV set face down. 2. Remove the 4 screws mounting the CRT to the front cabinet. 3. Lift the CRT. 4-2 Samsung Electronics

File name WS32W6HAX_XEC.ES030.1.07.pdf

Alignment and Adjustments 5. Alignment and Adjustments 5-1 General Alignment Instructions 1. Usually, a color TV-VCR needs only slight touch-up adjustment upon installation. Check the basic characteristics such as height, horizontal and vertical sync and focus. 2. Observe the picture for good black and white details. There should be objectionable color shading; if color shading is present, demagnetize, perform purity and convergence adjustments described below. 3. Use the specified test equipment or its equivalent. 4. Correct impedance matching is essential. 8. To protect against shock hazard, use an isolation transformer. 5. Avoid overload. Excessive signal from a sweep generator might overload the front-end of the TV. When inserting signal markers, do not allow the marker generator to distort test results. 6. Connect the TV only to an AC power source with voltage and frequency as specified on the backcover nameplate. 7. Do not attempt to connect or disconnect any wires while the TV is turned on. Make sure that the power cord is disconnected before replacing any parts. 5-2 Automatic Degaussing A degaussing coil is mounted around the picture tube, so that external degaussing after moving the TV should be unnecessary. But the receiver must be properly degaussed upon installation. The degaussing coil operates for about 1 second after the power is switched ON. If the set is moved or turned in a different direction, the power should be OFF for at least 10 minutes. If the chassis or parts of the cabinet become magnetized, poor color purity will result. If this happens, use an external degaussing coil. Slowly move the degaussing coil around the faceplate of the picture tube and the sides and front of the receiver. Slowly withdraw the coil to a distance of about 6 feet before turning power OFF. If color shading persists, perform the following Color purity and Convergence adjustments. 5-3 High voltage Check CAUTION: There is no high voltage adjustment on this chassis. The B+ power supply should be +135 volts (with full color- bar input and normal picture level). 1. Connect a digital voltmeter to the second anode of the picture tube. 2. Turn on the TV. Set the Brightness and Contrast controls to minimum (zero beam current). 3. Adjust the Brightness and contrast controls to both extremes. Ensure that the high voltage does not exceed 32 KV under any conditions. Samsung Electronics 5-1 Alignment and Adjustments 5-4 RF AGC Adjustment 1. Turn to the strongest local station. 2. Turn the AGC control fully clockwise (VR101, on the MAIN board). 3. Adjust the AGC control until noise(snow)disappears from the screen. 5-5 FOCUS Adjustment 1. Input a black and white signal. 2. Adjust the tuning control for clearest picture. 3. Adjust the FOCUS control for well defined scanning lines in the center area of the screen. 5-6 SCREEN Adjustment 1. Turn to the ACTIVE channel. 2. Adjust the VR screen for a normal picture is (no blooming or flyback line). 3. Adjust the SC

File name WS32W6HAX_XEC.ES030.1.09.pdf

Troubleshooting 6. Troubleshooting 6-1 No Power No Check Stand-by 5V on the Main Board Yes No Check SDA1/SCL1 on the Micom Module Yes No Check/Replace IC201 (TDA4780) ICA01 (Auto-Plus) Tuner MICOM Module AUDIO Module A/V Terminal Board (TDA6920) Feature Box Module Check HD Signal on the Feature Box Module Yes Check/Replace Q804, D824 RL802, D805 IC803, D802 D829 on the Power Board Replace Feature-Box Module Check/Replace Q405, D407 Q400, Q402 Q404 on the Power Board Samsung Electronics 6-1 Troubleshooting 6-2 No Picture Yes Check IC101 (TDA9810) #10 (AGC), #12 (CVBS) No No Check Feature Box Module M-Y/CVBS, H SYNC, HS2, Y, SC100 Yes Check/Replace IC101, Tuner Replace Feature Box Module No Check IC201 (TDA4780) #14 (SC), #15 (ABL), #19 (Cut off) Yes Replace TDA4780 Check/Replace IC501, IC502, IC503 on the CRT Board. 6-2 Samsung Electronics Troubleshooting 6-3 No Sound Yes Check IC601, IC602 # 5 (MUTE) No No Check Audio Module MAIN-L, SUR, CENTER, S-RESET, QSS-IN Yes Check/Replace Q602, Q603 Micom Module IC601, IC602 Check/Replace IC101 Micom Module Audio Module No Check IC604 #9, #14, #15 Yes Check/Replace IC604 MICOM Module Replace IC601, IC602 Samsung Electronics 6-3

File name WS32W6HAX_XEC.ES030.1.10.pdf

Exploded Views and Parts List 7. Exploded View & Parts List 7-1 WS32W6HA Samsung Electronics 7-1 7-2.Parts List No. 1 Code No. *AA91-00093A *HA91-00093A AA64-00020A Description & Specification ASSY-CABINET,FRONT;DP,32W6,SV808P SEH ,HB, ASSY-CABINET,FRONT;DP,32W6,SV808P SEH ,HB, CABINET-FRONT;-,WS32W6,SV808P SEH ML,HIP DOOR-CONTROL;-,28W6,SV-808P,HIPS,HB,GRAY INLAY-CONTROL;32W6,SCT53A MW,PS SHEET,T0 LATCH-DOOR;-,-,-,KIFUCO LA701,BADGE-BRAND;AL,SS,SILVER,L65,R2000,-,WINDOW-REMOCON;-,28W6,-,PC,V0,LG41338,KNOB-POWER;-,28W6,SV-808P,ABS,HB,GRAY SPRING-CS;-,SUS304,0.6,OD12.2,H13,N4,-,SPRING-CS;-,SUS304,0.5,OD7,H13.5,N5,-,-, INDICATOR-LED;-,28C7,-,ACRYL,-,CLR,INDICATOR-LED;-,28C7,-,ACRYL,-,CLR,SCREW-TAPTITE(IND+CF);RH,+,B,M4,L15,ZPC(BLK),SWR KNOB-CONTROL;-,28C7,S53A,ABS,HB,G3676 KNOB-CONTROL;DP,28W6,AA64-10809C,-,-,GRAY SCREW-TAPTITE(KC+CF);RH,+,B,M4,L15,ZPC(BLK),SWR ASSY-PCB,CONTROL;DP,SCT53A,32W6,WIDE,HUN HOLDER-CONTROL;-,28W6,-,V0,BLK,INLAY-DVB;28W6,S51A SEH,PS SHEET,T0.3,BL CRT-COLOR;-,W76EGX023X122,+380MG,-,104DE CLAMP-D,COIL;NYLON 66,V2,BLK,TVI 25~29,SCREW-ASSY(CRT+CF);WC,HH,+,M5,L31.5,SWRCH18A,ZPC CLAMP-D,COIL;NYLON-66,V0,NTR,DADH300,25 ASSY-PCB,CRT;-,SCT53A ,32",EUROPE,ASSY-HOLDER,SPK;DP,PP,8OHM/15W,GRAY,32 W SCREW-ASSY(SPK+CF);WP,RH,+,M4,L25,SWRCH18A,-,ZPC CABINET-BACK;-,WS32W6,-,HIPS,V2,BLK,-,SCREW-TAPTITE(CB+CF);RH,+,B,M4,L20,ZPC(BLK),SWR POWER-CORD;-,KJP-140,KLCE-2F,2.4m,HOUS,S POWER-CORD;DP,CP3,-,2.4M,BLK,AC250V,10A Q'ty 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 4 4 1 1 1 4 1 8 1 1 Remarks OTHERS EUROPATRADE 1-1 1-2 1-3 1-4 1-5 1-6 1-7 1-8 1-9 1-10 1-11 1-12 1-13 1-14 2 2-1 2-2 2-3 2-4 3 3-1 4 4-1 4-2 AA64-00004A AA64-00007B AA61-30001A AA64-70117B AA64-00002A AA64-00005A AA61-60005K AA61-60003T AA64-00191A AA64-40529A 6003-001026 AA64-10809C AA64-00217B 6003-001026 AA95-00173A AA61-00002A AA64-00008A AA03-00016A AA65-30113A AA60-10050R AA65-30017A AA95-00176A AA91-00023B AA60-10050A AA64-00019A 6003-001025 AA39-10003B HA39-010001 S.N.A S.N.A OTHERS EUROPATRADE OTHERS EUROPATRADE OTHERS EUROPATRADE DELETE ITEM OTHERS SEUK 7-2 Samsung Electronics

File name WS32W6HAX_XEC.ES030.1.12.pdf

8. Electric Parts List 8-1.WS32W6HA Loc Part-No Description & Specification Remarks Loc Part-No Description & Specification Remarks ASSY-PCB,MAIN(OPT) * AA94-00745A ASSY-PCB,MAIN(OPT);WS32W6HAS,SCT53A,EU,W C604 C605 C606 C607 2305-000149 2401-000192 2305-000149 2401-000192 2305-000149 2401-000603 2401-000318 2401-000603 2401-000192 2305-000149 2401-000192 2305-000149 2305-000149 2401-000192 2401-000603 2401-000318 2401-000603 2301-000383 2301-000383 2305-000149 2401-000603 2401-000962 2401-000480 2305-000665 2401-000480 2401-002286 2305-000665 2401-003034 2401-000832 2305-000665 2401-002286 2401-002286 2305-000665 2401-003034 2401-003034 2305-000665 2305-000665 2305-000665 2305-000665 2401-001397 2305-000665 2401-002273 2305-000665 2305-000407 2305-000149 2401-000287 2401-000287 2305-000149 2201-000423 2201-000423 2201-000375 2201-000423 2305-000149 2201-000234 2401-000302 C-FILM,MPEF;100nF,5%,100V,TP,12x12.5x6.5 C-AL;1000uF,20%,50V,GP,TP,16x25,7.5 C-FILM,MPEF;100nF,5%,100V,TP,12x12.5x6.5 C-AL;1000uF,20%,50V,GP,TP,16x25,7.5 C-FILM,MPEF;100nF,5%,100V,TP,12x12.5x6.5 C-AL;1uF,20%,50V,GP,TP,5x11,5 C-AL;100uF,20%,25V,LZ,TP,8x11.5,5 C-AL;1uF,20%,50V,GP,TP,5x11,5 C-AL;1000uF,20%,50V,GP,TP,16x25,7.5 C-FILM,MPEF;100nF,5%,100V,TP,12x12.5x6.5 C-AL;1000uF,20%,50V,GP,TP,16x25,7.5 C-FILM,MPEF;100nF,5%,100V,TP,12x12.5x6.5 C-FILM,MPEF;100nF,5%,100V,TP,12x12.5x6.5 C-AL;1000uF,20%,50V,GP,TP,16x25,7.5 C-AL;1uF,20%,50V,GP,TP,5x11,5 C-AL;100uF,20%,25V,LZ,TP,8x11.5,5 C-AL;1uF,20%,50V,GP,TP,5x11,5 C-FILM,PEF;10nF,5%,50V,TP,6x7x3.2mm,5mm C-FILM,PEF;10nF,5%,50V,TP,6x7x3.2mm,5mm C-FILM,MPEF;100nF,5%,100V,TP,12x12.5x6.5 C-AL;1uF,20%,50V,GP,TP,5x11,5 C-AL;22uF,20%,50V,GP,TP,5x11,5 C-AL;10uF,20%,50V,GP,TP,5x11,5 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m C-AL;10uF,20%,50V,GP,TP,5x11,5 C-AL;470uF,20%,16V,WT,TP,10x12.5,5 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m C-AL;220uF,20%,16V,WT,TP,8x11.5,5 C-AL;220uF,20%,25V,GP,TP,8x11.5,5 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m C-AL;470uF,20%,16V,WT,TP,10x12.5,5 C-AL;470uF,20%,16V,WT,TP,10x12.5,5 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m C-AL;220uF,20%,16V,WT,TP,8x11.5,5 C-AL;220uF,20%,16V,WT,TP,8x11.5,5 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m C-AL;470uF,20%,25V,GP,TP,10x16,5 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m C-AL;220uF,20%,25V,HR,TP,10x20mm,5m C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m C-FILM,MPEF;470nF,5%,100V,TP,-,5mm C-FILM,MPEF;100nF,5%,100V,TP,12x12.5x6.5 C-AL;100uF,20%,16V,WT,TP,6.3x11,5 C-AL;100uF,20%,16V,WT,TP,6.3x11,5 C-FILM,MPEF;100nF,5%,100V,TP,12x12.5x6.5 C-CERAMIC,DISC;27pF,5%,50V,NPO,TP,5x3,2. C-CERAMIC,DISC;27pF,5%,50V,NPO,TP,5x3,2. C-CERAMIC,DISC;220pF,5%,50V,RH,TP,9.5x3. C-CERAMIC,DISC;27pF,5%,50V,NPO,TP,5x3,2. C-FILM,MPEF;100nF,5%,100V,TP,12x12.5x6.5 C-CERAMIC,DISC;150pF,5%,50V,CH,TP,9.5x3, C-AL;100uF,20%,25V,GP,TP,6.3x11,5 CONNECTOR-HEADER;BOX,5P,1R,2.5mm,STRAIGH CONNECTOR-HEADER;BOX,3P,1R

File name WS32W6HAX_XEC.ES030.1.15.pdf

Wiring Diagram 9. Wiring Diagram 9-1 SCT53A Wiring Diagram POWER SW AC CORD/MASTER REMOCON MOD. AV CONTROL KEY/VIDEO/S-VHS INPUT HEADPHONE OUTPUT POWER BOARD GND GND GT808/GT809 TO PFC GT801/GT802 /GT803 TO POWER SW ON/OFF ST5V MUTE 16V 8V 8V 34V 34V GND GND GND STD-5V R-LED G-LED IR D-COIL EW VG ABL VDN VDP GND AFC 135V NC GND NC HEATER GND 25V GND NC 215V HD GND GND 33V MAIN BOARD GND C-IN GND Y-IN GND R-IN L-IN GND HP-R HP-L KEY GND STD-5V CN07A TO POWER SW CN08A TO AV CONTROL CN09A TO AV CONTROL CN15/4P TO MAIN SPEAKER SCL2 SDA2 NC NC NC GND FACT SCL1 SDA1 ST5V CN801 TO CRT CN17/3P TO CENTER SPEAKER CNFAC Samsung Electronics 9-1

File name WS32W6HAX_XEC.ES030.1.16.pdf

Schematic Diagrams 11. Schematic Diagrams 11-1 MAIN 1 Samsung Electronics 11-1 Schematic Diagrams 11-2 MAIN 2 11-2 Samsung Electronics Schematic Diagrams 11-3 POWER & DEFLECTION (WIDE) TP1 TP2 TP3 TP4 TP5 TP6 TP7 TP8 : Power Line Samsung Electronics 11-3 Schematic Diagrams 11-3-1 POWER & DEFLECTION (FLAT) TP2 TP1 TP1 TP2 TP3 TP4 TP3 TP5 TP6 TP4 TP7 TP8 TP5 TP6 TP8 TP7 : Power Line 11-4 Samsung Electronics Schematic Diagrams 11-4 TTX, m-COM Samsung Electronics 11-5 Schematic Diagrams 11-5 AUDIO MODULE 11-6 Samsung Electronics Schematic Diagrams 11-6 AV TERMINAL Samsung Electronics 11-7 Schematic Diagrams 11-7 CRT-DRIVE 11-8 Samsung Electronics Schematic Diagrams 11-8 CONTROL(WIDE) Samsung Electronics 11-9 Schematic Diagrams 11-8-1 CONTROL, SIDE-AV (FLAT) 3.3K 1.8K 12K 6.8K 27K 11-10 Samsung Electronics Schematic Diagrams 11-9 FEATURE BOX Samsung Electronics 11-11