Hitachi 36SDX01SR free download

File name 36SDX01B.pdf

PA No. 0140 36SDX01SR/MM1R 36SDX01S/MM1T SERVICE MANUAL MM1R/MM1T NTSC R/C: CLU-433FC Models 36SDX01SR/36SDX01S and 36SDX88B are in the same Solid State Color Television family. The main difference between the 36SDX01SR/36SDX01S and 36SDX88B is the control panel and the CRT. Please refer to model 36SDX88B schematics, assembly, wiring, test and troubleshooting information when servicing models 36SDX01SR/36SDX01S. Refer to Service Manual PA No. 0110 issued in December 1998. ADJUSTMENT Please refer to Service Manual PA No. 0110 when adjusting 36SDX01SR/36SDX01S. The only difference is the Chopper Voltage as stated below. SYMBOL NO. # DESCRIPTION CHOPPER VOLTAGE ADJUSTMENT (PA No. 0110 SECTION 2.3.1 PAGE 47) 36SDX88B/MM1 VGA MODE=112±0.5V DTV MODE=124±0.5V SVGA MODE=140±0.5V RT01 FOCUS ADJUSTMENT (PA No. 0110 SECTION 3.3 PAGE 81) SAME AS STATED IN PA No. 0110. 36SDX01SR/MM1R VGA MODE=112±0.5V DTV MODE=124±0.5V SVGA MODE=140±0.5V SAME AS STATED IN PA No. 0110. 36SDX01S/MM1T VGA MODE=105±0.5V DTV MODE=120±0.5V SVGA MODE=135±0.5V SEE BELOW 36SDX01S/MM1T ONLY 5. Vertical Line Adjustment Adjust Focus on Cross-Hatch Circle Pattern focusing the point as shown in the right figure. 6. Adjust RT01 focusing only at vertical line so that it becomes the most thick; the adjustment point which can be seen the clearest without any saturation. Concentration point: Inner point of the circle as shown in the fight figure. Note: Adjust Horizontal Center Focus again after adjusting Vertical Focus. RT01 The second vertical line from the left end. REAR VIEW The end of Cross-Hatch CPT PWB SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT S O L I D S TAT E C O L O R T E L E V I S I O N MAY 2000 HHEA-MANUFACTURING DIVISION 36SDX01SR/MM1R AND 36SDX01S/MM1T ONLY PARENTAL CONTROL (V-Chip) operation check Preparation for Adjustment (1) Receive a channel with V-Chip signal. (2) Push MENU and select CUSTOM menu by using or button. (3) Select PARENTAL CONTROL by using or button. (4) Press button to set PARENTAL CONTROL mode. (5) Enter "7777" for SECRET CODE. (6) Select MOVIE RATINGS and TV RATING by using or button. (7) Press button to set MOVIE RATINGS and TV RATINGS. Adjustment Procedure (1) Select MOVIE RATINGS MPAA (PG) and TV RATINGS (TV-14/ALL BLOCK) (2) Check that Picture & audio should be blocked as follows "RATING BLOCKED" is displayed when picture is blocked. Receive Signal Picture/Audio Condition TV-PG UNBLOCK MPAA PG BLOCK TV-Y7-FV UNBLOCK Receive Signal Picture/Audio Condition TV-PG BLOCK MPAA PG UNBLOCK TV-Y7-FV UNBLOCK (5) Select MOVIE RATINGS MPAA (PG-13) and TV RATINGS (TV-Y7/ALL BLOCK) (6) Check that Picture & audio should be blocked as follows "RATING BLOCKED" is displayed when picture is blocked. Receive Signal Picture/Audio Condition TV-PG BLOCK MPAA PG UNBLOCK TV-Y7-FV BLOCK (7) Same check as (1) to (6) should be applied for PINP sub picture. Main picture should receive a channel without V-chip signal. Sub picture should receive a channe