File information: | |
File name: | Sc a30_33_35 xaa.part2.rar |
Size: | 1770 kB |
Extension: | rar |
Mfg: | SAMSUNG |
Model: | SCA*30,A*33,A*35 🔎 |
Original: | |
Descr: | SAMSUNG SCA*33,A*35, A*35.... |
Group: | Electronics > Consumer electronics > Photo > Digital cameras |
Uploaded: | 09-04-2005 |
User: | PanBG |
Multipart: | 0 1 2 3 4 5 6 7 |
Information about the files in archive: | ||
Decompress result: | OK | |
Extracted files: | 9 | |
File name 20030125151045333_SC-A30_XAA[1].0000051600.E.02.pdf 1. Precautions 1. Be sure that all of the built-in protective devices are replaced. Restore any missing protective shields. 2. When reinstalling the chassis and its assemblies, be sure to restore all protective devices, including : control knobs and compartment covers. 3. Make sure that there are no cabinet openings through which people--particularly children --might insert fingers and contact dangerous voltages. Such openings include the spacing between the picture tube and the cabinet mask, excessively wide cabinet ventilation slots, and improperly fitted back covers. If the measured resistance is less than 1.0 megohm or greater than 5.2 megohms, an abnormality exists that must be corrected before the unit is returned to the customer. 4. Leakage Current Hot Check (See Fig. 1) : Warning : Do not use an isolation transformer during this test. Use a leakage current tester or a metering system that complies with American National Standards Institute (ANSI C101.1, Leakage Current for Appliances), and Underwriters Laboratories (UL Publication UL1410, 59.7). 5. With the unit completely reassembled, plug the AC line cord directly the power outlet. With the unit's AC switch first in the ON position and then OFF, measure the current between a known earth ground (metal water pipe, conduit, etc.) and all exposed metal parts, including : antennas, handle brackets, metal cabinets, screwheads and control shafts. The current measured should not exceed 0.5 milliamp. Reverse the power-plug prongs in the AC outlet and repeat the test. 6. X-ray Limits : The picture tube is designed to prohibit X-ray emissions. To ensure continued X-ray protection, replace the picture tube only with one that is the same type as the original. (Reading should not be above 0.5mA) Device Under Test Test all exposed metal surfaces 2-Wire Cord Also test with plug reversed (using AC adapter plug as required) Earth Ground Leakage Currant Tester Fig. 1 AC Leakage Test 7. Antenna Cold Check : With the unit's AC plug disconnected from the AC source, connect an electrical jumper across the two AC prongs. Connect one lead of the ohmmeter to an AC prong. Connect the other lead to the coaxial connector. 8. High Voltage Limit : High voltage must be measured each time servicing is done on the B+, horizontal deflection or high voltage circuits. Heed the high voltage limits. These include the X-ray protection Specifications Label, and the Product Safety and X-ray Warning Note on the service data schematic. 9. Some semiconductor ("solid state") devices are easily damaged by static electricity. Such components are called Electrostatically Sensitive Devices (ESDs); examples include integrated circuits and some field-effect transistors. The following techniques will reduce the occurrence of component damage caused by static electricity. 10. Immediately before handling any semiconductor components or assemblies, drain the electrostatic charge from your body by touching a known earth ground. Alternatively | ||
File name 20030125151045333_SC-A30_XAA[1].0000051600.E.03.pdf 2. Service Tips 2-1 How to replace the bulb 1 Remove the power source before replacing the bulb. 1 Use the JC6V-3W/G4 (100H) halogen lamp (maker : USHIO) to reduce the disk of fire. 1 If you have any trouble in replacing the bulb, contact you nearest authorized service center. 1. Disassemble the VIDEO LIGHT unit from camcorder with a small screwdriver (see figure). 2. Pull out the VIDEO LIGHT unit carefully. Take care of the cable which connects the LIGHT and camcorder. 3. Disassemble the cover carefully from the LIGHT unit. Be careful. The cover is easily broken. 4. Pull out the bulb with flat pliers. The bulb is easily broken. Do not apply excessive force when you use flat pliers. 5. Replace the bulb. Replace the bulb using flat pliers and a dry cloth. The dry cloth is used to prevent finger prints. Make sure that the bulb is exactly in place to reduce the risk of fire. 6. Assemble the cover carefully to the LIGHT unit (see figure). 7. Assemble the LIGHT unit to camcorder with a small screwdriver (see figure). Note : To prevent the bulb from being smudged with finger prints, handle it with a dry cloth, etc. If the bulb is smudged, wipe it completely. PUSH 1 2 cloth 2 H 1 Samsung Electronics 2-1 | ||
File name 20030125151045333_SC-A30_XAA[1].0000051600.E.04.pdf 3. Product Specifications and Comparison Chart 3-1 NTSC Model (SCA30/SCA33/SCA35/SCA80/SCA85) System Recording system SCA30/SCA33/SCA35/SCA80/SCA85 Video: 2 rotary heads helical scanning FM Audio: FM monaural system (SCA80/SCA85: FM stereo) Video signal Usable cassette NTSC color, EIA standard SCA30/SCA33/SCA35: 8 mm SCA80/SCA85: Hi8 or 8 mm Tape speed Speed mode Recording time FF or REW time Image device Optical zoom ratio Focal length: f SP: approx. 14.345 mm/sec Record: SP only P6-120: 120 min P6-120: approx. 6.5 min. CCD (Charge Coupled Device) SCA30/SCA33: 16X SCA30/SCA33: 3.9~62.6 mm SCA35/SCA80/SCA85: 4.0~88.0 mm SCA35/SCA80/SCA85: 22X Playback: SP and LP F Filter diameter Focus system Macro Min. Illumination SCA30/SCA33: 1.4 46 mm Inner Auto wide macro 0.3 lux (visible) SCA35/SCA80/SCA85: 1.6 Connectors Video out Mini jack, 1 Vp-p, 75 ohms Unbalanced Audio out Mini jack, 7.7 dBs, Monaural (SCA80/SCA85: stereo) imp.: less than 2.2 kohms External mic Monaural (SCA80/SCA85: stereo), Ø3.5 General Power requirement Power consumption 6.0~7.2 V DC SCA30/SCA31: 3.9 W SCA35: 4.2 W SCA85: 4.8 W Built-in mic Operating temperature Dimensions (W x H x D) Condenser mic, omni-directional 0°C to 40°C (32°F to 104°F) SCA35/SCA80/SCA85 : 105.7 x 104.5 x 210 (41.6 x 41.1 x 82.7 inch) SCA30/SCA33 : 105.7 x 104.5 x 201 (41.6 x 41.1 x 79.1 inch) Weight SCA35/SCA80/SCA85: 760 g (1.672 lbs) SCA30/SCA33: 740g (1.628 lbs) SCA33: 4.1 W SCA80: 4.7 W Samsung Electronics 3-1 Products Specifications 3-2 PAL Model (VP-A30/VP-A31/VP-A33/VP-A34/VP-A800/VP-A850 System Recording system VP-A30/VP-A31/VP-A33/VP-A34/VP-A800/VP-A850 Video: 2 rotary heads helical scanning FM Audio: FM monaural system (VP-A800/A850: FM stereo) Video signal Usable cassette PAL colour, CCIR standard VP-A30/VP-A31/VP-A33/VP-A34: 8 mm VP-A800/VP-A850: Hi8 or 8 mm Tape speed Speed mode Recording time FF or REW time Image device Optical zoom ratio Focal length: f SP: approx. 20.051 mm/sec Record: SP only P5-90: 90 min. P5-90: approx. 8 min. CCD (Charge Coupled Device) VP-A30/VP-A31/VP-A33: 16x VP-A30/VP-A31/VP-A33: 3.9~62.6 mm VP-A34/VP-A800/VP-A850: 4.0~88.0 mm VP-A34/VP-A800/VP-A850:22x Playback: SP and LP F Filter diameter Focus system Macro Min. Illumination VP-A30/VP-A31/VP-A33: 1.4 46 mm Inner Auto wide macro 0.3 lux (visible) VP-A34/VP-A800/VP-A850: 1.6 Connectors Video out Mini jack, 1 Vp-p, 75 ohms Unbalanced Audio out Mini jack, 7.7 dBs, Monaural (VP-A800/VP-A850: stereo) imp.: less than 2.2 kohms External mic Monaural (VP-A800/VP-A850: stereo), Ø3.5 General Power requirement Power consumption 6.0~7.2 V DC VP-A30/VP-A31: 3.9 W VP-A34: 4 W VP-A850: 4.6W Built-in mic Operating temperature Dimension (W x H x D) Condenser mic, omni-directional 0°C to 40°C (32°F to 104°F) VP-A34/VP-A800/VP-A850: 105.7 x 104.5 x 210 VP-A30/VP-A31/VP-A33: 105.7 x 104.5 x 201 Weight VP-A34/VP-A800/VP-A850: 760 g VP-A30/VP-A31/VP-A33: 740 g VP-A33: 4.2 W VP-A800: 4.5W 1 The technical specifi | ||
File name 20030125151045333_SC-A30_XAA[1].0000051600.E.06.pdf 4. Disassembly and Reassembly 4-1 Cabinet Disassembly 4-1-1 Ass'y Cover Housing Removal 1 REMOVE 2 SCREWS. A 2 REMOVE THE ASS'Y COVER HOUSING IN THE DIRECTION OF ARROW. A Fig. 4-1 Ass'y Cover Housing Removal Samsung Electronics 4-1 Disassemblr and Reassembly 4-1-2 Ass'y Case Top Removal 1 REMOVE ASS'Y CASE TOP BY GENTLELY RELEASING 2 LOCKING TABS WITH A SMALL SCREW DRIVER. (SEE DETAIL "A") REASSEMBLY : PUT THE 7 TABS INTO THE SLOT, WHILE SLIDING IT AS SHOWN IN DETAIL "B". 2 LOCKING TABS "B" PRECISION SCREW DRIVER < DETAIL "A" > Fig. 4-2 Ass'y Case Top Removal < DETAIL "B" > 4-2 Samsung Electronics Disassemblr and Reassembly 4-1-3 Ass'y Front Removal 2 REMOVE THE ASS'Y FRONT IN THE DIRECTION OF ARROW. A B 1 A 1 1 REMOVE 4 SCREWS. 3 B DISCONNECT THE FPC FROM THE CN702 OF ASS'Y AUDIO BOARD. 1 Fig. 4-3 Ass'y Front Removal Samsung Electronics 4-3 Disassemblr and Reassembly 4-1-4 Ass'y Case Right Removal 2 REMOVE THE UNIT CASE IN THE DIRECTION OF ARROW. A 1 REMOVE 3 SCREWS. A DISASSEMBLE AFTER TURNING KNOB to be "LOCK". 1 1 Fig. 4-4 Ass'y Case Right Removal 4-4 Samsung Electronics Disassemblr and Reassembly 4-1-5 Ass'y Case Left Removal 4 REMOVE THE CASE LEFT ASSEMBLY IN THE DIRECTION OF ARROW. A 2 A 1 2 3 REMOVE 2 SCREWS. REMOVE 2 SCREWS. REMOVE 1 SCREWS. Fig. 4-5 Ass'y Case Left Removal Samsung Electronics 4-5 Disassemblr and Reassembly 4-1-6 Ass'y EVF/CVF Removal Caution of assembling (CN604 of the CVF models) : Insert the cable to the left most side of CN604 (Pin no.1 side) 1 2 REMOVE 2 SCREWS. REMOVE 3 SCREWS. 2 A 3 REMOVE THE EVF/CVF ASS'Y IN THE DIRECTION OF ARROW. A Fig. 4-6 Ass'y EVF/CVF Removal 4-6 Samsung Electronics Disassemblr and Reassembly 4-1-7 Ass'y Function Board Removal 1 REMOVE 1 SCREW. 3 REMOVE THE ASS'Y FUNCTION BOARD IN THE DIRECTION OF ARROW. A A 2 REMOVE 1 SCREW. Fig. 4-7 Ass'y Case Rear Removal Samsung Electronics 4-7 Disassemblr and Reassembly 4-1-8 Ass'y 8mm Deck Removal A 1 REMOVE 3 SCREWS. 2 1 REMOVE THE ASS'Y 8MM DECK IN THE DIRECTIOB OF ARROW. Fig. 4-8 Ass'y 8mm Deck Removal 4-8 Samsung Electronics Disassemblr and Reassembly 4-1-9 Ass'y Camera Removal B 1 REMOVE 1 SCREW. A 1 REMOVE THE CAMERA IN THE DIRECTION OF ARROW. A B Fig. 4-9 Ass'y Camera Removal Samsung Electronics 4-9 Disassemblr and Reassembly 4-2 Circuit Boards Location ASS'Y EIS BOARD (EIS MODEL) ASS'Y FRONT BOARD (NO EIS MODEL) ASSY CCD BOARD ASS'Y MAIN BOARD ASS'Y EVF BOARD ASS'Y REAR BOARD ASS'Y FUNCTION BOARD ASS'Y CVF BOARD Fig. 4-10 Circuit Boards Location 4-10 Samsung Electronics Disassemblr and Reassembly 4-3 Connector Diagrams Caution of assembling (CN604 of the CVF models) : Insert the cable to the left most side of CN604 (Pin no.1 side) NO. CONNECTOR CN51 DIRECTION DECK DECK MAIN PCB MAIN PCB REAR PCB FUNCTION PCB CVF CCD PCB LENS FPC LENS FPC FRONT FFC FRONT FFC FRONT PCB MIC ASS'Y MIC ASS'Y MIC ASS'Y LIGHT ASS'Y EVF CONNECTOR CN501 CN52 C | ||
File name 20030125151045333_SC-A30_XAA[1].0000051600.E.07.pdf 5. Alignment and Adjustment 5-1. Mechanism Alignment · Refer to mechanical manual "DE-6 (AD68-30200A)"for the adjustment and checks of mechanism section. · The location of test point (See Fig.1) Test Point: PB RF - Pin 11 of CN605 Head Switching Trigger - Pin 9 of CN605 14 12 10 8 6 4 2 13 11 9 7 5 3 1 PB RF Head Switching - Trigger CN605 Fig. 1 Test point Fig. 2 Test location of test point Samsung Electronics 5-1 Alignment and Adjustment UNLOADING OPEN COMMON GROUND IC601 28PIN IC601 27PIN IC601 26PIN EJECT UNLOADING STOP LOADING LOADING STOP PLAY POSITION EJECT UNLOADING STOP LOADING STOP PB IC601 28PIN L L H H IC601 27PIN H L L H IC601 26PIN H H L L ACTION MODE EJECT UNLOADING STOP LOADING STOP PLAY, FF, Z/RTN, STILL... 5-2 Samsung Electronics Alignment and Adjustment 5-2 Camera Section Adjustment Note : 1. This system has 1) EEPROM to store the confirmed adjustment data. 2) DSP (Digital Signal Process ; ICP01 - Main board) chip to process the signal of camera parts. 3) One test point for the frequency adjustment of DSP main clock (P. CLK). 4) The special mode for camera adjustment using the function keys on the left case. 2. Keep in mind 1) All adjustment steps should performed using the remote controller. 5-2-1 Preparations 1. Equipment to be used 1) DC Power supply 2) Oscilloscope 3) Frequency counter 4) Vectorscope 5) Waveform monitor 6) Color monitor or TV 7) Various charts - Color bar chart - Gray-scale chart, etc... 2. Composition of camera P.C.Boards 1) Main PCB 2) CCD PCB 3) CVF /EVF PCB 3. Adjustment preparations 1) The function keys on the left case is used as a camera adjust tool. 2) Press the confirm button when each manual adjustment step is completed to write the adjustment data to the EEPROM. 3) After each adjustment step is completed, OSD shows "OK!". 4) To cancel the adjustment mode, remove the power source. 4. The function keys on the left case The following is a chart explaining the use of each button : Using Button MENU/ENTER (CONFIRM) Z/RTN (DATA DOWN) C/RESET (DATA UP) TITLE (MODE UP) DATE/TIME (MODE DOWN) M/F Ring dial (FAR/NEAR) ZOOM TELE/ZOOM WIDE Adjustment Data store after finishing adjustment by DATA UP/DOWN button. When change data value of adjust state. Mode change. Manual focus adjustment. Move the zoom position of lens. Samsung Electronics 5-3 Alignment and Adjustment The function keys left case is required to adjust the camera section. BLC DATA DOWN DATA UP OSD ON/OFF MODE DOWN MODE UP CONFIRM 1 ZOOM LEVER : ZOOM TELE/WIDE Note : In service adjustment mode, button names are different from those in customer camera function control mode. EX) MENU/ENTER button is the same as confirm. 5. How to get into service "ADJUST" mode STEP 1 1. Remove the lithium battery from the camcorder. 2. Connect the power source (battery/ DC cable). 3. Eject the tape if it is in the unit. 4. Set the power switch of the camcorder to "CAMERA" position. 5. Set OSD on state. STEP 2 1. Press and | ||
File name 20030125151045333_SC-A30_XAA[1].0000051600.E.10.pdf 6. Exploded View and Parts List 6-1 Cabinet Assembly (1) 6-2 Cabinet Assembly (2) 6-3 Cabinet Assembly (3) 6-4 Cabinet Assembly (4) 6-5 EVF (SCA30/VP-A30/VP-A31/VP-A34/VP-A800/VP-A850) 6-6 CVF (SCA33/SCA35/SCA80/SCA85/VP-A33) 6-7 Mechanical Parts (1) 6-8 Mechanical Parts (2) 6-9 Mechanical Parts (3) 6-2 6-4 6-6 6-8 6-10 6-12 6-14 6-16 6-18 Samsung Electronics 6-1 Exploded View and Parts List 6-1 Cabinet Assembly (1) 109 108 107 904 905 113 902 350 903 111 905 105 110 112 306 114 905 104 903 105 903 103 102 903 101 905 6-2 Samsung Electronics Exploded View and Parts List Loc. No New Part No 101 AD64-32016A AD64-32016B AD64-32016C AD64-32016D AD64-32016E AD64-32016F AD64-32024A AD64-32024B AD64-32024C AD64-32024D AD64-32024E AD64-10897A AD63-30583A AD63-30582A Description and Specification Remark VP-A850 VP-A34 VP-A800 SCA35 SCA80 SCA85 VP-A30 VP-A31 VP-A33 SCA30 SCA33 ALL ALL SCA35/SCA80/SCA85/VP-A34 VP-A800/VP-A850 SCA30/SCA33/VP-A30/VP-A31 VP-A33 ALL ALL ALL ALL ALL ALL SCA30/VP-A30 VP-A31/VP-A33/VP-A34/VP-A800 VP-A850 SCA33/SCA35/SCA80/SCA85 ALL ALL VP-A30/VP-A31/VP-A34/VP-A800 VP-A850/SCA30 VP-A33/SCA33/SCA35/SCA80 SCA85 VP-A850 VP-A30 VP-A31 VP-A33 VP-A34 VP-A800 SCA30 SCA33 SCA35 SCA80 SCA85 VP-A30/VP-A31/VP-A800 VP-A33 SCA33/SCA80 SCA30 VP-A34/VP-A850 SCA35/SCA85 ALL ALL ALL ALL ALL 102 103 104 CASE-LEFT(C);-,ABS94,HB,-,-,-,22X,VP-A85 CASE-LEFT(C);-,ABS94,HB,-,-,-,22X,VP-A34 CASE-LEFT(C);-,ABS94,HB,-,-,-,22X,VP-A80 CASE-LEFT(C);-,ABS94,HB,-,-,-,22X,SCA35 CASE-LEFT(C);-,ABS94,HB,-,-,-,22X,SCA80 CASE-LEFT(C);-,ABS94,HB,-,-,-,22X,SCA85 CASE-LEFT(A);-,ABS94,HB,-,-,-,16X,VP-A30 CASE-LEFT(A);-,ABS94,HB,-,-,-,16X,VP-A31 CASE-LEFT(A);-,ABS94,HB,-,-,-,16X,VP-A33 CASE-LEFT(A);-,ABS94,HB,-,-,-,16X,SCA30 CASE-LEFT(A);-,ABS94,HB,-,-,-,16X,SCA33 KNOB-MENU;-,ABS94,HB,-,-,VP-A850 COVER-JIG;-,ABS94,HB,-,-,-,-,VP-A850 COVER-LEFT(C);-,ABS94,HB,-,-,-,22X,VP-A8 AD63-30586A COVER-LEFT(A);-,ABS94,HB,-,-,-,16X,VP-A3 105 106 107 108 109 110 111 AD61-21149A AD98-12026W AD61-70087A AD61-70088A AD61-50785A AD64-11018A AD64-11015A AD64-11015B AD64-11015C AD61-21150A AD64-10898A AD90-10849J HOLDER-LOCK EVF;-,POM,-,BLK,-,VP-A850 ASS'Y-BASE TRIPOD;VP-A85,BLK/AL RAIL-EVF;-,POM,-,-,BLK,-,RAIL-LOCK;-,ABS94,HB,-,BLK,-,GUIDE-EVF;-,ABS94,HB,-,BLK,-,BUTTON-FADE;-,ABS94,HB,-,-,VP-A850 BUTTON-BLC;-,ABS94,HB,-,BLC,VP-A30 BUTTON-BLC;-,ABS94,HB,-,XDR',VP-A850 BUTTON-BLC;-,ABS94,HB,-,I-BLC,SCA85 HOLDER-MENU;-,POM,-,NTR,-,VP-A850 KNOB-MF;-,ABS94,HB,-,-,VP-A850 ASS'Y-FUNCTION;EVF,A3 112 113 114 AD90-10849K ASS'Y-FUNCTION;CVF,A3 306 AD98-12026X AD98-12027P AD98-12027Q AD98-12027R AD98-12027S AD98-12027T AD98-12027U AD98-12027V AD98-12027W AD98-12027X AD98-12027Y AD90-10842X AD90-10850B AD90-10850C AD90-10851Z AD94-00034A AD94-00035A AD60-10543A AC60-10020A AC60-10055A AC60-10054A AD60-00002A ASS'Y-CASE LEFT;VP-A850,22X/Hi8 ASS'Y-CASE LEFT;VP-A30,ASS'Y-CASE LEFT;VP-A31,ASS'Y-CASE LEFT;VP-A33,ASS'Y-CASE LEFT;VP-A34,ASS'Y-CASE LEFT;VP-A80,ASS'Y-CASE LEFT;SCA30,ASS'Y- | ||
File name 20030125151045333_SC-A30_XAA[1].0000051600.E.14.pdf 8.PCB Diagrams 3/27/95 10:02 AM Page 1 8. PCB Diagrams 8-1 Main PCB (Component Side) 8-2 Main PCB (Conductor Side) 8-3 Main PCB (Hi-8) (Component Side) 8-4 Main PCB (Hi-8) (Conductor Side) 8-5 Rear PCB 8-6 Front PCB with EIS 8-7 Front PCB without EIS (Mono) 8-8 Front PCB without EIS (Stereo) 8-9 CVF PCB 8-10 EVF PCB 8-11 CCD PCB 8-12 Function PCB 8-2 8-4 8-6 8-8 8-10 8-11 8-12 8-13 8-14 8-15 8-16 8-16 Samsung Electronics 8-1 8.PCB Diagrams 3/27/95 10:02 AM Page 2 PCB Diagrams 8-1 Main PCB (Component Side) 8-2 Samsung Electronics 8.PCB Diagrams 3/27/95 10:02 AM Page 3 PCB Diagrams RESISTOR COIL DIODE CONDENSER IC&WAFER XTAL TR Samsung Electronics 8-3 8.PCB Diagrams 3/27/95 10:02 AM Page 4 PCB Diagrams 8-2 Main PCB (Conductor Side) 8-4 Samsung Electronics 8.PCB Diagrams 3/27/95 10:02 AM Page 5 PCB Diagrams TR RESISTOR CONDENSER DIODE IC&WAFER COIL XTAL Samsung Electronics 8-5 8.PCB Diagrams 3/27/95 10:02 AM Page 6 PCB Diagrams 8-3 Main PCB (Hi-8) (Component Side) 8-6 Samsung Electronics 8.PCB Diagrams 3/27/95 10:02 AM Page 7 PCB Diagrams Samsung Electronics 8-7 8.PCB Diagrams 3/27/95 10:02 AM Page 8 PCB Diagrams 8-4 Main PCB (Hi-8) (Conductor Side) 8-8 Samsung Electronics 8.PCB Diagrams 3/27/95 10:02 AM Page 9 PCB Diagrams Samsung Electronics 8-9 8.PCB Diagrams 3/27/95 10:02 AM Page 10 PCB Diagrams 8-5 Rear PCB (Component Side) (Conductor Side) 8-10 Samsung Electronics 8.PCB Diagrams 3/27/95 10:03 AM Page 11 PCB Diagrams 8-6 Front PCB with EIS (Component Side) (Conductor Side) Samsung Electronics 8-11 8.PCB Diagrams 3/27/95 10:03 AM Page 12 PCB Diagrams 8-7 Front PCB without EIS (Mono) (Component Side) 8-12 Samsung Electronics 8.PCB Diagrams 3/27/95 10:03 AM Page 13 PCB Diagrams 8-8 Front PCB without EIS (Stereo) (Component Side) (Conductor Side) Samsung Electronics 8-13 8.PCB Diagrams 3/27/95 10:03 AM Page 14 PCB Diagrams 8-9 CVF PCB (Component Side) (Conductor Side) 8-14 Samsung Electronics 8.PCB Diagrams 3/27/95 10:03 AM Page 15 PCB Diagrams 8-10 EVF PCB (Component Side) (Conductor Side) Samsung Electronics 8-15 8.PCB Diagrams 3/27/95 10:03 AM Page 16 PCB Diagrams 8-11 CCD PCB 8-12 Function PCB 8-16 Samsung Electronics | ||
File name 20030125151045333_SC-A30_XAA[1].0000051600.E.15.pdf 9. Wring Diagram 3/27/95 10:04 AM Page 1 9. Wring Diagram Caution of assembling (CN604 of the CVF models) : Insert the cable to the left most side of CN604 (Pin no.1 side) Samsung Electronics 9-1 | ||
File name 20030125151045333_SC-A30_XAA[1].0000051600.E.16.pdf 10. Schematic Diagrams 3/27/95 10:04 AM Page 1 10. Schematic Diagrams 10-1 DC/DC Converter (Main) 10-2 System Control/Servo (Main) 10-3 Video (Normal) (Main) 10-4 Video (Hi-8) (Main) 10-5 Audio (Mono) (Main) 10-6 Audio (Stereo) (Main) 10-7 Camera (Main) 10-8 Rear 10-9 CCD 10-10 CVF 10-11 EVF 10-12 Front with EIS 10-13 Front without EIS (Mono) 10-14 Front without EIS (Stereo) 10-15 Function 10-2 10-3 10-4 10-5 10-6 10-7 10-8 10-9 10-10 10-12 10-12 10-13 10-14 10-15 10-16 Note For schematic Diagram - Resistors are in ohms, 1/8W unless otherwise noted. - Circled numbers refer to waveforms. Special note : Most semiconductor devices are electrostatically sensitive and therefore require the special handling techniques described under the "electrostatically sensitive (ES) devices" section of this service manual. Note : Do not use the part number shown on this drawing for ordering. The correct part number is shown in the parts list (may be slightly different or amended since this drawing was prepared). Important safety notices : Components identified with the mark components. Use only the same type. have the special characteristics for safety. When replacing any of these Samsung Electronics 10-1 10. Schematic Diagrams 3/27/95 10:04 AM Page 2 Schematic Diagrams 10-1 DC/DC Converter (Main) 10-2 Samsung Electronics 10. Schematic Diagrams 3/27/95 10:04 AM Page 3 Schematic Diagrams 10-2 System Control/Servo (Main) Samsung Electronics 10-3 10. Schematic Diagrams 3/27/95 10:04 AM Page 4 Schematic Diagrams 10-3 Video (Normal) (Main) 10-4 Samsung Electronics 10. Schematic Diagrams 3/27/95 10:04 AM Page 5 Schematic Diagrams 10-4 Video (Hi-8) (Main) Samsung Electronics 10-5 10. Schematic Diagrams 3/27/95 10:04 AM Page 6 Schematic Diagrams 10-5 Audio (Mono) (Main) 10-6 Samsung Electronics 10. Schematic Diagrams 3/27/95 10:04 AM Page 7 Schematic Diagrams 10-6 Audio (Stereo) (Main) Samsung Electronics 10-7 10. Schematic Diagrams 3/27/95 10:04 AM Page 8 Schematic Diagrams 10-7 Camera (Main) 10-8 Samsung Electronics 10. Schematic Diagrams 3/27/95 10:04 AM Page 9 Schematic Diagrams 10-8 Rear Samsung Electronics 10-9 10. Schematic Diagrams 3/27/95 10:04 AM Page 10 Schematic Diagrams 10-9 CCD 10-10 Samsung Electronics 10. Schematic Diagrams 3/27/95 10:04 AM Page 11 Schematic Diagrams 10-10 CVF Samsung Electronics 10-11 10. Schematic Diagrams 3/27/95 10:04 AM Page 12 Schematic Diagrams 10-11 EVF 10-12 Samsung Electronics 10. Schematic Diagrams 3/27/95 10:04 AM Page 13 Schematic Diagrams 10-12 Front with EIS Samsung Electronics 10-13 10. Schematic Diagrams 3/27/95 10:04 AM Page 14 Schematic Diagrams 10-13 Front without EIS (Mono) 10-14 Samsung Electronics 10. Schematic Diagrams 3/27/95 10:04 AM Page 15 Schematic Diagrams 10-14 Front without EIS (Stereo) Samsung Electronics 10-15 10. Schematic Diagrams 3/27/95 10:04 AM Page 16 Schematic Diagrams 10-15 FUNCTION 10-1 |
Date | User | Rating | Comment |