Sony DVP-S9000ES free download

File name DVP-S9000ES.pdf

DVP-S9000ES RMT-D122A/D122E/D122O/D122P US Model Canadian Model AEP Model UK Model Australian Model Chinese Model Hong Kong Model SERVICE MANUAL Photo: Gold type SPECIFICATIONS SACD/DVD player Laser Semiconductor laser Signal format system PAL/(NTSC) AUDIO OUT (1, 2) DIGITAL OUT (OPTICAL) DIGITAL OUT (COAXIAL) VIDEO OUT S VIDEO OUT Outputs Jack type Phono jacks General Output level Load impedance Power requirements 220 - 240 V AC, 50/60 Hz 120 V AC, 60Hz (EXCETP US, Canadian) Power consumption 48 W 43 W (EXCEPT US, Canadian) Dimensions (approx.) 430 Ч 126 Ч 398 mm (17 Ч 5 Ч 15 11/ in.) 16 (w/h/d) incl. projecting parts Mass (approx.) 12.6 kg (27 lb 12 oz) Operating temperature 5 °C to 35 °C (41 °F to 95 °F) Operating humidity 25 % to 80 % Audio characteristics Frequency response DVD (PCM 96 kHz): 2 Hz to 44 kHz (­2 dB ±1 dB at 44 kHz) CD: 2 Hz to 20 kHz (±0.5 dB) SACD: 2 Hz to 100 kHz (­3 dB ±1 dB at 50 kHz) Signal to noise ratio more than 115 dB (DVD) Harmonic distortion DVD: Less than 0.0015% CD: Less than 0.002% SACD: Less than 0.0015% Dynamic range More than 103 dB (DVD) More than 103 dB (SACD) More than 99 dB (CD) Wow and flutter Less than detected value (±0.001% W PEAK) 2 Vrms Over 10 kilohms (at 50 kilohms) Wave length: 660 nm Optical ­18 dBm output connector Phono jack Phono jacks 0.5 Vp-p 1.0 Vp-p 75 ohms terminated 75 ohms, sync negative 75 ohms, sync negative 75 ohms terminated Y: 1.0 Vp-p 4-pin mini DIN C: 0.3 Vp-p (PAL) (EXCEPT US, Canadian) C: 0.286 Vp-p (NTSC) Y: 1.0 Vp-p PB/CB, PR/CR: ±0.35 Vp-p Supplied accessories 75 ohms, sync negative 75 ohms COMPONENT Phono jacks VIDEO OUT (Y, PB/CB, PR/CR) Check that you have the following items: · Audio connecting cord (1) · Video connecting cord (1) · S-link (Control S) connecting cord (1) · S video cord (1) · Power cord (1) · Remote commander (remote) (1) · Size AA (R6) batteries (2) Design and specifications are subject to change without notice. SACD/DVD PLAYER SAFETY CHECK-OUT After correcting the original service problem, perform the following safety checks before releasing the set to the customer: 1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. 2. Check the interboard wiring to ensure that no wires are "pinched" or contact high-wattage resistors. 3. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement. 4. Look for parts which, though functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement. 5. Check the line cord for cracks and abrasion. Recommend the replacement of any such line cord to the customer. 6. Check the B+ voltage to see it is at the values specified. 7. Check the antenna terminals, metal trim, "metallized" knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as