Minolta DI-350 free download

File name 350FIELD.PDF

FrameMaker Ver.5.5E(PC) COVER [FIELD SERVICE] FOR Di350 98.12.09 FrameMaker Ver.5.5E(PC) COVER [FIELD SERVICE] FOR Di350 98.12.09 Di350 SERVICE MANUAL Di350 SERVICE MANUAL [FIELD SERVICE] [FIELD SERVICE] Copyright 1999 MINOLTA Co., Ltd. Printed in Japan Use of this manual should be strictly supervised to avoid disclosure of confidential information. MINOLTA Co., Ltd. 1171-7991-11 99022300 FrameMaker Ver.5.5E(PC) PL Standard Document Ver.03 99.01.27 Safety Precautions for Inspection and Service When performing inspection and service procedures, observe the following precautions to prevent accidents and ensure utmost safety. V Depending on the model, some of the precautions given in the following do not apply. Different markings are used to denote specific meanings as detailed below. WARNING CAUTION Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. The following graphic symbols are used to give instructions that need to be observed. Used to call the service technician's attention to what is graphically represented inside the marking (including a warning). Used to prohibit the service technician's from doing what is graphically represented inside the marking. Used to instruct the service technician's to do what is graphically represented inside the marking. WARNING 1. Always observe precautions. · Parts requiring special attention in this product will include a label containing the mark shown on the left plus precautionary notes. Be sure to observe the precautions. · Be sure to observe the "Safety Information" given in the Operator's Manual. 2. Before starting the procedures, be sure to unplug the power cord. · This product contains a high-voltage unit and a circuit with a large current capacity that may cause an electric shock or burn. · The product also contains parts that can jerk suddenly and cause injury. · If this product uses a laser, laser beam leakage may cause eye damage or blindness. 3. Use the specified parts. · For replacement parts, always use the genuine parts specified in the manufacturer's parts manual. Installing a wrong or unauthorized part could cause dielectric breakdown, overload, or undermine safety devices resulting in possible electric shock or fire. · Replace a blown electrical fuse or thermal fuse with its corresponding genuine part specified in the manufacturer's parts manual. Installing a fuse of a different make or rating could lead to a possible fire. If a thermal fuse blows frequently, the temperature control system may have a problem and action must be taken to eliminate the cause of the problem. P-1 FrameMaker Ver.5.5E(PC) PL Standard Document Ver.03 99.01.27 4. Handle the power cord with care and never use a multiple outlet. · Do not break, crush or otherwise damage the power cord.

File name 350GEN.PDF

FrameMaker Ver.5.5E(PC) COVER [GENERAL] FOR Di350 98.12.25 FrameMaker Ver.5.5E(PC) COVER [GENERAL] FOR Di350 98.12.25 Di350 SERVICE MANUAL Di350 SERVICE MANUAL [GENERAL] [GENERAL] Copyright 1999 MINOLTA Co., Ltd. Printed in Japan Use of this manual should be strictly supervised to avoid disclosure of confidential information. MINOLTA Co., Ltd. 1171-7990-11 99023000 17196 FrameMaker Ver.5.5(PC) Di350 98.12.25 INDEX (GENERAL) GENERAL MECHANICAL/ELECTRICAL FrameMaker Ver.5.5E(PC) Di350 GENERAL, MECHANICAL/ELECTRICAL 98.12.18 Di350 GENERAL FrameMaker Ver.5.5E(PC) Di350 GENERAL, MECHANICAL/ELECTRICAL 98.12.18 CONTENTS 1. 2. 3. 4. 5. 6. 7. SAFETY INFORMATION ... G-1 SPECIFICATIONS ... G-8 PRECAUTIONS FOR INSTALLATION ... G-10 PRECAUTIONS FOR USE ... G-11 HANDLING OF THE CONSUMABLES ... G-12 OTHER PRECAUTIONS ... G-12 SYSTEM OPTIONS ... G-13 i FrameMaker Ver.5.5E(PC) Di350 GENERAL, MECHANICAL/ELECTRICAL 98.12.18 1171SBG0100A 1 SAFETY INFORMATION Laser Safety This is a digital machine which prints by means of a laser. There is no possibility of danger from the laser, provided the machine is operated according to the instructions in this manual. Since radiation emitted by the laser is completely confined within protective housing, the laser beam cannot escape from the machine during any phase of user operation. This machine is certified as a Class 1 product. This means the machine does not produce hazardous laser radiation. CAUTION: The use of controls, adjustments or performance of procedures other than those specified in this manual may result in hazardous radiation exposure. Because of this, Minolta strongly recommends that you operate your copy machine only as described in this documentation. Internal Laser Radiation Maximum Average Radiation Power: 36.7µW at laser aperture of the print head unit Wavelength: 770-810nm This product employs a Class IIIb Laser Diode that emits an invisible laser beam. The Laser Diode and Scanning Polygon Mirror are incorporated in the print head unit. The print head unit is NOT A FIELD SERVICE ITEM. Therefore, the print head unit should not be opened under any circumstances. Laser Aperture of the Print Head Unit 1166O263AA This figure shows the view inside the Right Side Door with the Imaging Unit removed. For United States CDRH regulation This copier is certified as a Class 1 Laser product under the Radiation Performance Standard according to the Food, Drug and Cosmetic Act of 1990. Comp

File name 350QKRF.PDF

Di350 SWITCHES ON PWBs, TECH. REP. SETTINGS 17196 CONTENTS 1. PRECAUTIONS FOR HANDLING THE PWBs ... S-1 1-1. Precautions for Transportation and Storage ... S-1 1-2. Precautions for Replacement and Inspection ... S-1 2. CONTROL PANEL KEYS AND TOUCH PANEL ... S-2 2-1. Control Panel Keys ... S-2 2-2. Explanation of the Touch Panel ... S-3 (1) Basic Screen ... S-3 (2) Warning Screens ... S-4 3. FUNCTION OF SWITCHES AND OTHER PARTS ON PWBs ... S-5 3-1. PWB Location ... S-5 3-2. PWB-A (Master Board) ... S-5 3-3. UN1 (Control Panel) ... S-6 3-4. PWB-L (PPM Switching Board) ... S-6 3-5. UN2 (MFB Board) ... S-7 4. USER'S CHOICE MODE ... S-9 4-1. User's Choice Selection Screen ... S-9 4-2. User's Choice Function Setting Procedure ... S-9 4-3. User's Choice Function Tree ... S-10 4-4. Settings in the User's Choice Mode ... S-11 5. TECH. REP. MODE ... S-16 5-1. Tech. Rep. Mode Menu Screen ... S-16 5-2. Tech. Rep. Mode Function Setting Procedure ... S-16 5-3. Tech. Rep. Mode Setting Tree ... S-17 5-4. Settings in the Tech. Rep. Mode ... S-18 (1) Tech. Rep. Choice ... S-18 (2) System Input ... S-22 (3) Administrator # Input ... S-23 (4) Counter ... S-23 (5) Function ...

File name PRNT_CTR.PDF

UNPACKING/SETTING-UP INSTRUCTIONS Printer Controller NOTES · Keep all packing materials out of the reach of children. · Before setting up, be sure to unplug the power cord of the copier. 4608-7744-01 Printed in Japan Printer Controller I Unpacking Make sure that the following items are contained in the shipping carton. 1. Printer Controller...1 2. Engine I/F Cable ...1 3. Mounting screws - long screw (3Ч40mm) ...4 - short screw (3Ч16mm)...2 4. Printer Driver (CD-ROM) ...1 5. Setting-Up Instructions ...1 6. Windows Version User's Manual ...1 7. Macintosh Version User's Manual ...1 8. End User's License Agreement ...1 9. Short Harness with Ferrite Core (Except the U.S.A. and Canada)...1 10. Ferrite Core (Except the U.S.A. and Canada) ...1 11. Tie Band (Except the U.S.A. and Canada) ...2 4608U002AA 4608U001AA I Installing the Printer Controller 1. Cut out the blank cover on the back side of the machine. 2. Reach into the hole made in step 1 and pull out the power cord, consisting of two green cables and two yellow cables, from the inside. NOTE Before performing the setting-up procedures, be sure to unplug the power cord of the machine from the power outlet. 3. Remove the three screws from the housing. 4608U003AC 4. At the back of the Printer Controller, plug in the power cord. 4608UU004AA 4608-7744-01 ­1­ Printer Controller I Installation of the Ferrite Core (Except the U.S.A. and Canada) 5. Secure the Printer Controller to the machine with six screws. Long Screw (3Ч40mm)... 4 Short Screw (3Ч16mm) ... 2 4608U005AC (1) Short Harness with Ferrite Core 1. Remove the screw from the back side of the machine and connector cover at the Paper Take-Up Unit. 4608U034AA 6. Connect one end of the Engine I/F Cable to the printer port on the machine and the other end to the printer port on the Printer Controller. 2. Disconnect the PJ1 harness. 4608U017AB 4608U035AA 3. Connect the PJ1 harness to the Short Harness with Ferrite Core contained in the kit as illustrated on the left. 4608U036AA 4608-7744-01 ­2­ Printer Controller 4. Casefully, reinstall the connector cover to the Paper Take-Up Unit. NOTE Use care to prevent the wiring from being caught between the machine frame and connec