Samsung VP-L100 free download

File name VP-L100.pdf

8mm CAMCORDER VP-L100/VP-L150 SCL100/SCL150 SERVICE 8mm CAMCORDER Manual CONTENTS For mechanical disassembly and adjustment, refer to the "Mechanical Manual" (DE-6 AD68-30200A). 1. Precautions 2. Reference Information 3. Product Specifications and Comparison Chart 4. Disassembly and Reassembly 5. Alignment and Adjustment 6. Exploded View and Parts List 7. Electrical Parts List 8. Block Diagrams 9. PCB Diagrams 10. Wiring Diagram 11. Schematic Diagrams A

File name VP-L100_a.PDF

1. Precautions 1. Be sure that all of the built-in protective devices are replaced. Restore any missing protective shields. 2. When reinstalling the chassis and its assemblies, be sure to restore all protective devices, including : control knobs and compartment covers. 3. Make sure that there are no cabinet openings through which people--particularly children --might insert fingers and contact dangerous voltages. Such openings include the spacing between the picture tube and the cabinet mask, excessively wide cabinet ventilation slots, and improperly fitted back covers. If the measured resistance is less than 1.0 megohm or greater than 5.2 megohms, an abnormality exists that must be corrected before the unit is returned to the customer. 4. Leakage Current Hot Check (See Fig. 1) : Warning : Do not use an isolation transformer during this test. Use a leakage current tester or a metering system that complies with American National Standards Institute (ANSI C101.1, Leakage Current for Appliances), and Underwriters Laboratories (UL Publication UL1410, 59.7). 5. With the unit completely reassembled, plug the AC line cord directly the power outlet. With the unitХs AC switch first in the ON position and then OFF, measure the current between a known earth ground (metal water pipe, conduit, etc.) and all exposed metal parts, including : antennas, handle brackets, metal cabinets, screwheads and control shafts. The current measured should not exceed 0.5 milliamp. Reverse the power-plug prongs in the AC outlet and repeat the test. 6. X-ray Limits : The picture tube is designed to prohibit X-ray emissions. To ensure continued X-ray protection, replace the picture tube only with one that is the same type as the original. Device Under Test Test all exposed metal surfaces 2-Wire Cord Also test with plug reversed (using AC adapter plug as required) Earth Ground (Reading should not be above 0.5mA) Leakage Currant Tester Fig. 1 AC Leakage Test 7. Antenna Cold Check : With the unitХs AC plug disconnected from the AC source, connect an electrical jumper across the two AC prongs. Connect one lead of the ohmmeter to an AC prong. Connect the other lead to the coaxial connector. 8. High Voltage Limit : High voltage must be measured each time servicing is done on the B+, horizontal deflection or high voltage circuits. Heed the high voltage limits. These include the X-ray protection Specifications Label, and the Product Safety and X-ray Warning Note on the service data schematic. 9. Some semiconductor (Тsolid stateУ) devices are easily damaged by static electricity. Such components are called Electrostatically Sensitive Devices (ESDs); examples include integrated circuits and some field-effect transistors. The following techniques will reduce the occurrence of component damage caused by static electricity. 10. Immediately before handling any semiconductor components or assemblies, drain the electrostatic charge from your body by touching a known earth ground. Alternatively

File name VP-L100_b.PDF

Reference Information 2. Reference Information 2-1 IC Blocks 2-1-1 IC501 (KA8322) Samsung Electronics 2-1 Reference Information 2-1-2 IC601 (CXP87240A) 2-2 Samsung Electronics Reference Information 2-1-3 ICP01 (KS7213) Samsung Electronics 2-3 Reference Information 2-1-4 ICP03 (TDA8786A) 2-4 Samsung Electronics Reference Information 2-1-5 ICP04 (KS7306B) Samsung Electronics 2-5 Reference Information 2-1-6 ICP05 (UPD784038 / AF MICOM) 2-6 Samsung Electronics Reference Information 2-1-7 ICZ01 (KS7314 / D.ZOOM) Samsung Electronics 2-7 Reference Information MEMO 2-8 Samsung Electronics

File name VP-L100_c.PDF

3. Product Specifications and Comparison Chart 3-1 Product Specifications (SCL100 / SCL150) Design and specifications are subject to change without notice. Operation SYSTEM LCD Recording systems Video signal Cassette format Tape speed Three-inch color TFT Liquid Crystal Display (LCD) screen Video : Two rotary heads, helical FM scanning / Audio : FM stereo system NTSC color, EIA standard 8 mm SP mode (Standard Play) : approx. 14.345 mm/sec Description Recording/Playback time SP mode (Standard Play) : 1 hour (P6-60) Fast-forward/rewind time Image device Viewfinder Lens Automatic focus system Color temperature Aperture correction Approx. 3 minute 30 seconds (P6-60) CCD (Charge Coupled Device) Black and White electronic viewfinder Combined 16X power zoom and (32X:SCL100, 64X:SCL150) digital zoom lens, f=3.9 ~ 62.4mm, F1.4 Auto wide macro, Filter diameter 46mm. Inner Auto Automatic with back light adjustment OUTPUT CONNECTORS Video output Audio output Mini jack, 1Vp-p, 75 ohms, unbalanced, SYNC negative Mini jack, 7.5dBs for an output impedance of less than 2.2 Kohms GENERAL Power requirement Power consumption Tripod attachment thread Microphone Temperature range Dimensions/weight AC power adapter (7.2V) ; battery pack (6.0V) 6.5W (Camera Recording, LCD on) Attachment screw less than 6mm long Electric condensor microphone, omni-directional, monaural type Operating : 0°C to 40°C (32°F to 104°F); storage : -20°C to 60°C (-4°F to 140°F) Approx. 213 X 116 X 107 mm (L X H X W); Approx. 1000 g Excluding battery pack and cassette. Samsung Electronics 3-1 Product Specifications 3-2 Product Specifications (VP-L100 / VP-L150) Design and specifications are subject to change without notice. Operation SYSTEM LCD Recording systems Video signal Cassette format Tape speed Three-inch colour TFT Liquid Crystal Display (LCD) screen Video : Two rotary heads, helical FM scanning / Audio : FM stereo system PAL colour, CCIR standard 8 mm SP mode (Standard Play) : approx. 20.051 mm/sec Description Recording/Playback time SP mode (Standard Play) : 1 hour (P5-60) Fast-forward/rewind time Image device Viewfinder Lens Automatic focus system Colour temperature Aperture correction Approx. 4 minute (P5-60) CCD (Charge Coupled Device) Black and White electronic viewfinder Combined 16X power zoom and 32X(VP-L150) digital zoom lens, f=3.9 ~ 62.4mm, F1.4 Auto wide macro, Filter diameter 46mm. Inner Auto Automatic with back light adjustment OUTPUT CONNECTORS Video output Audio output Mini jack, 1Vp-p, 75 ohms, unbalanced, SYNC negative Mini jack, 7.5dBs for an output impedance of less than 2.2 Kohms GENERAL Power requirement Power consumption Tripod attachment thread Microphone Temperature range Dimensions/weight AC power adapter (7.2V) ; battery pack (6.0V) 6.5W (Camera Recording, LCD on) Attachment screw less than 6mm long Electric condensor microphone, omni-directional, monaural type Operating : 0°C to 40°C (32°F to 104°F); storage : -20°C to 60°C (-4°F to 140°F) Appr

File name VP-L100_d.PDF

4. Disassembly and Reassembly 4-1 Cabinet and PCB 4-1-1 Ass'y Cover-Housing removal OE APPLY POWER AND EJECT THE COVER HOUSING. REMOVE THE ASS'Y COVER-HOUSING IN THE DIRECTION OF ARROW. ґ REMOVE 2 SCREWS. Fig. 4-1 Ass'y Cover-Housing removal Samsung Electronics 4-1 Disassembly and Reassembly 4-1-2 Ass'y Case-Top removal · NOTE : CLOSE THE HOUSING ASS'Y AFTER DISASSEMBLING. OE REMOVE THE ASS'Y-CASE-TOP BY GENTLY RELEASING 2 LOCKING TABS WITH A PRECISION SCREW DRIVER. (SEE DETAIL "A") · REASSEMBLY : PUT THE 7 TABS INTO THE SLOT WHILE SLIDING IT AS SHOWN IN DETAIL "B". 2 LOCKING TABS "B" PRECISION SCREW DRIVER < DETAIL "A" > < DETAIL "B" > Fig. 4-2 Ass'y Case-Top removal 4-2 Samsung Electronics Disassembly and Reassembly 4-1-3 Ass'y Front removal Ё REMOVE THE ASS'Y-FRONT IN THE DIRECTION OF ARROW. REMOVE 1 SCREW. OE REMOVE 2 SCREWS. ^ DISCONNECT 2 CONNECTORS FROM THE CN891,CN893 OF AUDIO PCB. ґ REMOVE 2 SCREWS. Fig. 4-3 Ass'y Front removal Samsung Electronics 4-3 Disassembly and Reassembly 4-1-4 Ass'y Case-Right removal Ё REMOVE THE ASS'Y CASE-RIGHT IN THE DIRECTION OF ARROW "B". SLIDE THE ZOOM SWITCH IN THE DIRECTION OF ARROW "A". OE REMOVE 1 SCREW. ґ REMOVE 2 SCREWS. Fig. 4-4 Ass'y Case-Rignt removal 4-4 Samsung Electronics Disassembly and Reassembly 4-1-5 Ass'y Case-Left removal REMOVE 1 SCREW. ^ REMOVE THE ASS'Y CASE-LEFT IN THE DIRECTION OF ARROW. Ё REMOVE 2 SCREWS. DISCONNECT THE CONNECTER FROM THE CN502 OF MAIN PCB. ґ REMOVE 3 SCREWS. OE REMOVE 1 SCREW. Fig. 4-5 Ass'y Case-Left removal Samsung Electronics 4-5 Disassembly and Reassembly 4-1-6 Ass'y Case-Battery removal ґ DISCONNECT THE CN961 OF THE REAR PCB FROM THE CN501 OF MAIN PCB AND THEN REMOVE THE ASS'Y CASE-BATTERY IN THE DIRECTION OF ARROW. OE REMOVE 1 SCREW. Fig. 4-6 Ass'y Case-Battery removal 4-6 Samsung Electronics Disassembly and Reassembly 4-1-7 Ass'y Case-Bottom removal ґ REMOVE THE CASE- BOTTOM IN THE DIRECTION OF ARROW. OE REMOVE 2 SCREWS. Fig. 4-7 Ass'y Case-Bottom removal Samsung Electronics 4-7 Disassembly and Reassembly 4-1-8 Ass'y-Deck removal REMOVE THE ASS'Y DECK IN THE DIRECTION OF ARROW . Ё REMOVE 1 SCREW. Ш DISCONNECT THE FPC FROM THE CN501 OF MAIN PCB. REMOVE 2 SCREWS. ^ DISCONNECT THE FPC FROM THE ASS'Y DECK. Fig. 4-8 Audio PCB and Ass'y-Deck removal 4-8 Samsung Electronics Disassembly and Reassembly 4-1-9 Ass'y Camera and Main PCB removal ґ REMOVE 2 SCREWS. CNP01 CNC01 OE DESOLDER SOLDERING POINT DISCONNECT THE CNC01 FROM THE CNP01 OF MAIN PCB AND THEN REMOVE THE ASS'Y CAMERA IN THE DIRECTION OF ARROW. Fig. 4-9 Ass'y Camera and Main PCB removal Samsung Electronics 4-9 Disassembly and Reassembly 4-1-10 Ass'y LCD removal OE REMOVE 5 SCREWS. "A" ґ REMOVE THE ASS'Y LCD IN THE DIRECTION OF ARROW "A". Fig. 4-10 Ass'y LCD removal 4-10 Samsung Electronics Disassembly and Reassembly 4-1-11 Ass'y EVF removal REMOVE 3 SCREWS. ґ REMOVE 1 SCREW. OE DISCONNECT THE LEAD CONNECTOR FR

File name VP-L100_e.PDF

5. Alignment and Adjustment 5-1 Mechanical Adjustment * Note 1 : Mechanical alignment is performed for the linearity of PB-RF(Envelope). * Note 2 : Refer to the mechanism manual ТDE-6У(AD68-30200A) for the mechanism alignment. Short between pin #67 of IC601 and GND in order to set the TEST MODE.(ThatХs Track Shift Mode) Connect the Head SW Pulse in CH1 and the PB-RF in CH2 to oscilloscope. Refer to the Fig1 for the location of test point. Play the alignment tape supplied, and fit the PB-RF form like as Fig1. (Refer to the alignment manual of the DE-6 described above). 5) If the alignment is completed, then remove the short wire for the release of the test mode. 1) 2) 3) 4) Test Point : PB RF - Pin 45 of IC201 Head Switching Trigger - Pin 96 of IC601 (PIN 96) (PIN 67) (PIN 45) Fig. 1 The location of test point Samsung Electronics 5-1 Alignment and adjustment 5-2 Camera Section Adjustment Note : 1. This system has 1) EEPROM to store the confirmed adjustment data. 2) DSP (Digital Signal Process ; ICP04 - Main board) chip to process the signal of camera parts. 3) One test point for the frequency adjustment of DSP main clock (P. CLK). 2. Keep in mind 1) Readjustment is needed when the EEPROM (ICP10 of Main board) is replaced. The reason is that EEPROM stores confirmed adjustment value of each adjustment step. 5-2-1 Preparations 1. Equipments to be used 1) DC Power supply 2) Oscilloscope 3) Frequency counter 4) Vectorscope 5) Waveform monitor 6) Color monitor or TV 7) Various charts - Color bar chart - Gray-scale chart, etc... 8) Alignment tape (Lion pattern) 2. Composition of camera P.C.Boards 1) Main PCB 3) EVF PCB 2) CCD PCB 4) LCD PCB 3. Adjustment preparations 1) Press the confirm button when each manual adjustment step is completed to write the adjustment data to the EEPROM. 2) After each adjustment step is completed, OSD shows ТOK!У. 3) To cancel the adjustment mode, remove the power source. 4. Menu Board The following is a chart explaining the use of each button : Using Button TITLE (CONFIRM) C.RESET (DATA DOWN) DISPLAY (DATA UP) MENU (MODE UP) DATE (MODE DOWN) FADE (FAR ) BLC (NEAR) Adjustment Data store after finishing adjustment by DATA UP/DOWN button. When changing data value of adjust state. Mode change. Focus adjustment. 5-2 Samsung Electronics Alignment and adjustment The function buttons on the Menu Board are used to control the camcorder additionally, These buttons should be used for adjustment of the camera section. Menu Board for camcorder adjustment Figure of button placement when Menu Board is used for service adjustment. Reassignment in the adjustment mode Note : In service adjustment mode, button names are different from those in customer camera function control mode. EX) TITLE button is the same as confirm. 5. How to get into service ТADJUSTУ mode STEP 1 1. Connect the power source (battery/ DC cable). 2. Eject the tape if it is in the unit. 3. Set the power switch of the camcorder to ТCAMERAУ position. 4. Set

File name VP-L100_f.PDF

6. Exploded View and Parts List Page 6-1 6-2 6-3 6-4 6-5 6-6 Cabinet Assembly (1) - - - - - - - - - - - - - - - - - - - - - 6-2 Cabinet Assembly (2) - - - - - - - - - - - - - - - - - - - - - 6-4 Mechanical Parts (1) - - - - - - - - - - - - - - - - - - - - - - 6-6 Mechanical Parts (2) - - - - - - - - - - - - - - - - - - - - - - 6-8 Mechanical Parts (3) - - - - - - - - - - - - - - - - - - - - - - 6-10 EVF - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-12 Samsung Electronics 6-1 Exploded View and Parts List 6-1 Cabinet Assembly (1) 6-2 Samsung Electronics Exploded View and Parts List Loc. No New Part No 101 101 101 102 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 127 127 129 130 130 131 131 131 131 132 133 134 135 136 137 138 139 140 140 140 140 141 141 142 143 144 145 146 147 148 149 902 903 904 906 AD64-30905E AD64-30905F AD64-30905H AD64-82001B AD64-10812A AD64-10880A AC61-42079A AD61-60601A AD61-21020A AD64-10814E AD90-10828F AD61-21021A AD90-10828D AD39-20825N AC61-20223A AC61-60034A AD61-21040A AD98-12016G AC62-12009A AD73-10039A AD59-90400A AD61-10999A AD90-10828E AD39-20826D AD61-12024A AD61-12013A AD98-12025A AD98-12025B AD98-12025H AD98-12025J AD98-12024P AD90-10833K AD90-10837Y AD59-10539A AD59-10539B AD59-10539C AD59-10539D AD64-30903C AD41-20302Y AD98-12003N AD64-30881E AD63-30537A AD64-10816A AD61-60578A AD61-12035A AD64-30901G AD64-30901K AD64-30901L AD64-30901M AD90-10828B AD90-10831J AD61-12022A AD90-30205Z AD07-10032J AD61-50687A AD61-60569A AD61-30183A AD64-10815A AD64-30902C AC60-10019A AC60-10020A AC60-10055A AC60-10073A Description and Specification CASE-LEFT;-,ABS94,V0,BLACK,-,VP-L100,-,CASE-LEFT;-,ABS94,V0,BLACK,-,SCL100,-,CASE-LEFT;-,ABS94,V0,BLACK,-,SCL150,-,LEG-3INCH;-,ABS,-,T1.5,BLK,-,VP-L100 KNOB-POWER;-,ABS,-,-,-,SV-S99 KNOB-EJECT;-,ABS,HB,BLK,-,VP-L100 STOPPER-POWER;ABS94HB,T1.0,-,RED,SV-H66, SPRING-KNOB POWER;SUS304 WPB HOLDER-POWER;-,-,-,BLK,-,SV-S99 KNOB-ROTARY;-,ABS94,HB,D/GRAY,-,VP-L100 ASSY-FUNC VCR BOARD;VP-L10 S8C-PAL,3INCH HOLDER-ROTARY;-,-,-,BLK,-,SV-S99 ASSY-FUNC TION BOARD;VP-L10 S8C-PAL,3INCH LEAD CONNECTOR-ASSY;-,51021-05,51021-02, HOLDER-LOCK;SECC,T1.0,NAT,-,-,SPRING-EJECT;CS,SUS 304,PI 0.25,D 3,L 9, HOLDER-EJECT;-,POM,-,BLK,-,SV-S99 ASSY-UNIT LCD OFF;SV-S99,INSULATION-SPEAKER;HIMERON,-,T0.3,W30,L3 RUBBER-SPEAKER;SILICONE,-,SCL90,SPEAKER-SYSTEM;28G13BSA,SCL90,SEA BRACKET-SPEAKER;-,SECC,SV-S99 ASSY-FUNC MEN BOARD;VP-L10 S8C-PAL,3INCH LEAD CONNECTOR-ASSY;TP,51021,51021,12P,8 BRACKET-HINGE;-,SUS,SCL90 BRACKET-GUIDE HINGE;-,SUS,SV-S99 ASSY-LENS HOOD;VP-L100,ASSY-CASE FRONT;VP-L100,ASSY-CASE FRONT;SCL100,ASSY-CASE FRONT;SCL150,ASSY-MIC;VP-A20,ASSY-FRONT BOARD;VP-L100,NOR,MONO ASSY-FRONT BOARD;VP-L150,NOR,MONO UNIT-CASE FRONT;VP-L100,UNIT-CASE FRONT;SCL100,UNIT-CASE FRONT;SCL150,UNIT-CASE FRONT;VP-L150,CASE-HINGE TOP;-,ABS,HB,BLACK,-,VP-L100, FPC-LCD;POLYWIDE,T0.10,18P,VP-L100 ASSY-HINGE;SV-S99,CASE-HINGE BOTTOM;-,ABS94,HB,-,-,B

File name VP-L100_g.PDF

7. Electrical Parts List Loc.No 152 152 152 152 Part No AD90-10824W AD90-10831L AD90-10838T AD90-10838U Desc & Spec ASSY-MAIN BOARD;VP-L10/BASIC,PAL,NOR,MON ASSY-MAIN BOARD;SC-L100/BASIC,NTSC,NOR,M ASSY-MAIN BOARD;SC-L150/BASIC,NTSC,NOR,M ASSY-MAIN BOARD;VP-L150/BASIC,PAL,NOR,MO C-CERAMIC,CHIP;10nF,10%,50V,X7R,1608,-,T C-CERAMIC,CHIP;56PF,5%,50V,CH,TP,1608,C-CERAMIC,CHIP;10nF,10%,50V,X7R,1608,-,T C-CERAMIC,CHIP;2.2nF,10%,50V,X7R,TP,1608 C-CERAMIC,CHIP;1uF,+80-20%,16V,Y5V,TP,20 C-TA,CHIP;10uF,20%,6.3V,-,3216,-,TP C-TA,CHIP;10uF,20%,6.3V,-,3216,-,TP C-TA,CHIP;10uF,20%,6.3V,-,3216,-,TP C-CERAMIC,CHIP;2.2nF,10%,50V,X7R,TP,1608 C-TA,CHIP;10uF,20%,6.3V,-,3216,-,TP C-CERAMIC,CHIP;1uF,+80-20%,16V,Y5V,TP,20 C-TA,CHIP;10uF,20%,6.3V,-,3216,-,TP C-TA,CHIP;1uF,20%,16V,-,TP,3216,C-CERAMIC,CHIP;1uF,+80-20%,16V,Y5V,TP,20 C-CERAMIC,CHIP;220pF,5%,50V,CH,1608,1.6m C-TA,CHIP;4.7uF,20%,10V,WT,3216,-,TP C-CERAMIC,CHIP;1uF,+80-20%,16V,Y5V,TP,20 C-AL,SMD;100UF,20%,6.3V,GP,TP,5.3X5.3X5 C-CERAMIC,CHIP;1uF,+80-20%,16V,Y5V,TP,20 C-TA,CHIP;100nF,20%,35V,-,TP,3216,C-CERAMIC,CHIP;1uF,+80-20%,16V,Y5V,TP,20 C-TA,CHIP;4.7uF,20%,10V,WT,3216,-,TP C-CERAMIC,CHIP;1uF,+80-20%,16V,Y5V,TP,20 C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;47NF,+80-20%,50V,Y5V,1608 C-CERAMIC,CHIP;47NF,+80-20%,50V,Y5V,1608 C-TA,CHIP;10uF,20%,6.3V,-,3216,-,TP C-TA,CHIP;10uF,20%,6.3V,-,3216,-,TP C-TA,CHIP;100uF,20%,6.3V,WT,7343,-,TP C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;1uF,+80-20%,16V,Y5V,TP,20 C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;3.3nF,10%,50V,X7R,TP,1608 C-TA,CHIP;100nF,20%,35V,-,TP,3216,C-TA,CHIP;4.7UF,20%,6.3V,-,TP,3216,C-TA,CHIP;22uF,20%,6.3V,-,TP,3528,C-CERAMIC,CHIP;5.6nF,10%,50V,CH,TP,1608, CONNECTOR-FPC/FC/PIC;18P,0.8mm,SMD-A,SN CONNECTOR-HEADER;3WALL,5P,1R,1.25MM,SMDIC-ROM;LA7454W,QFP,IC-AUDIO AMP;7052A,DIP,8P,-,SINGLE,35.5M INDUCTOR-SMD;33uH,10%,2.5x2x1.8mm INDUCTOR-SMD;330uH,10%,3.2x2.5x2.2mm TR-SMALL SIGNAL;2SB1119,PNP,500MW,PCP,TP TR-DIGITAL;DTC114EU,NPN,200mW,10K-10Kohm TR-SMALL SIGNAL;2SC4081,NPN,200mW,UMT,TP TR-ARRAY;UMX2N,NPN,2,50V,40V,100MA,300M R-CHIP;8.2Kohm,5%,1/16W,DA,TP,1608 R-CHIP;10Kohm,5%,1/16W,DA,TP,1608 R-CHIP;6.8Kohm,5%,1/16W,DA,TP,1608 R-CHIP;22Kohm,5%,1/16W,DA,TP,1608 R-CHIP;22ohm,5%,1/16W,DA,TP,1608 R-CHIP;1.8Kohm,5%,1/16W,DA,TP,1608 R-CHIP;100Kohm,5%,1/16W,DA,TP,1608 R-CHIP;33Kohm,5%,1/16W,DA,TP,1608 R-CHIP;10Kohm,5%,1/16W,DA,TP,1608 R-CHIP;0ohm,5%,1/16W,DA,TP,1608 R-CHIP;15Kohm,5%,1/16W,DA,TP,1608 R-CHIP;100Kohm,5%,1/16W,DA,TP,1608 R-CHIP;39Kohm,5%,1/16W,DA,TP,1608 R-CHIP;39Kohm,5%,1/16W,DA,TP,1608 Remark VPL100 SCL100 SCL150 VPL150 Loc.No R716 R719 R720 R721 R722 R723 R724 R726 R728 R730 R731 R750 R751 R752 R753 R754 R755 R850 R851 R852 R853 R854 R855 R856 R857 R858 R859 R860 R861 R862 R863 R864 R865 R866 Part No 2007-000091 2007-000090 2007-000094 2007-000691 2007-001114 2007-000124 2007-000078 2007-000070 2007-000643 2007-000079 2007-000102 2007-000078 2007-000076 2007-000084 2007-0000

File name VP-L100_h.PDF

8. Block Diagrams Page 8-1 8-2 8-3 8-4 8-5 8-6 8-7 8-8 8-9 8-10 Overall Block Diagram (Camera) - - - - - - - - - - - - - 8-2 Overall Block Diagram (VCR) - - - - - - - - - - - - - - - 8-3 DC/DC Converter - - - - - - - - - - - - - - - - - - - - - - - - 8-4 Drum Servo - - - - - - - - - - - - - - - - - - - - - - - - - - - - 8-5 Capstan Servo - - - - - - - - - - - - - - - - - - - - - - - - - - 8-6 Video Playback(SCL100/150) - - - - - - - - - - - - - - - 8-7 Video Record(SCL100/150) - - - - - - - - - - - - - - - - - 8-8 Video Playback(VP-L100/150) - - - - - - - - - - - - - - - 8-9 Video Record(VP-L100/150) - - - - - - - - - - - - - - - - 8-10 Audio - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 8-11 8-11 Camera Main - - - - - - - - - - - - - - - - - - - - - - - - - - 8-12 Samsung Electronics 8-1 Block Diagrams 8-1 Overall Block Diagram (Camera) 8-2 Samsung Electronics Block Diagrams 8-2 Overall Block Diagram (VCR) Samsung Electronics 8-3 Block Diagrams 8-3 DC/DC Converter 8-4 Samsung Electronics Block Diagrams 8-4 Drum Servo Samsung Electronics 8-5 Block Diagrams 8-5 Capstan Servo 8-6 Samsung Electronics Block Diagrams 8-6 Video Playback (SCL100/150) Samsung Electronics 8-7 Block Diagrams 8-7 Video Record (SCL100/150) 8-8 Samsung Electronics Block Diagrams 8-8 Video Playback (VP-L100/150) Samsung Electronics 8-9 Block Diagrams 8-9 Video Record (VP-L100/150) 8-10 Samsung Electronics Block Diagrams 8-10 Audio Samsung Electronics 8-11 Block Diagrams 8-11 Camera Main 8-12 Samsung Electronics

File name VP-L100_j.PDF

10. Wiring Diagram Samsung Electronics 10-1