File name 20031227092337859_CH2.pdf2. Alignment and Adjustment
2-1 Location of Test Point
Pin 29 of RIC1
Fig. 2-1 Location of Test Point Samsung Electronics 2-1
Alignment and Adjustment
2-2 Skew Adjustment
2-2-1 Adjustment Spec. and Test Point
Test Disc TDV-533 Chapter 14 Adjustment Spec. Flat Waveform Test Point "Pin 29 of RIC1" (Main PCB - Component Side) (See Fig. 2-1) Test Disc ; Service not Available Adjustment Location Screw A / B Ass'y Deck - Top Side (See Fig. 2-2)
Fig. 2-2 Ass'y Deck (Top Side)
2-2
Samsung Electronics
Alignment and Adjustment
2-2-2 SKEW Adjustment Method
Needed to minimize the variations in Skew of the Pickup unit and to provide optimum match with the recorded signal on the Disc. 1) Connect an Oscilloscope to the "Pin 29 of RIC1" Test Point (See Fig. 2-1). 2) Connect Power, Open the Tray and Play the TDV-533 Disc, Chapter 14. Set the Oscilloscope Range as follows : (Voltage ; 20mV/Div., Frequency ; 10m Sec.) 3) Adjust the Screws "A" and "B" (See Fig. 2-2) using a Hex screwdriver until you obtain a Flat Waveform and the picture is stable. Then, go to Chapter 1 and make sure the Waveform is Flat here as well. If not, you have to go back to Chapter 14 and adjust again. If you cannot obtain a Flat waveform, then the unit is defective. Note : The Deck must be in a horizontal position. Use both "A" and "B" screws to adjust.
Typical Waveform before Adjustment
Waveform after Correct Adjustment
Fig. 2-3 Envelope Waveform
Samsung Electronics
2-3
Alignment and Adjustment
MEMO
2-4
Samsung Electronics File name 20031227092337859_CH3.pdf3. Exploded View and Parts List
Page 3-1 Cabinet Assembly - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-2
3-2 Deck Assembly - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-4
Samsung Electronics
3-1
Exploded Views and Parts List
3-1 Cabinet Assembly
P025
W001
W005
W005 C015
P001
A001
C001 C002
3-2
Samsung Electronics
Exploded Views and Parts List
Loc. No A001 C001 C002 C015 P001 P025 W001 W005
Parts No. AK59-00011K AK97-00660B AK64-00503B AK64-00500C AK92-00339A AC39-10200N 6003-000275 6003-000117
Description ; Specification REMOCON-ASSY;DVD-P240/XAA,XAA,-,-,36,-,ASSY CABINET-FRONT;HIPS 94 V2,DVD-P240/X DOOR-TRAY;DVD-P240/XAA,TSEC,ABS 94HB,T2. CABINET-TOP;DVD-P142/XEL,SECC,T0.5,W429. ASSY PCB-MAIN;DVD-P241,MAIN ASSY CBF POWER CORD;EP2,SPT-2,AWG#18,1.8MT,WA SCREW-TAPTITE;BH,+,B,M3,L10,BLK ,SWCH101 SCREW-TAPTITE;BH,+,B,M3,L6,ZPC(YEL),SWRC
Remark
Samsung Electronics
3-3
Exploded Views and Parts List
3-2 Deck Assembly
H212
H102 H900 H202 H903
H205 H204 H903 H210
H207 H206 H904 H203 H209 H107 H105 H106 H103 H903 H206 H904
H211
H241
H108 H104
H109
3-4
Samsung Electronics
Exploded Views and Parts List
Loc. No H102 H103 H104 H105 H106 H107 H108 H109 H202 H203 H204 H205 H206 H207 H209 H210 H211 H212 H241 H900 H903 H904
Parts No. AH66-00111B AK66-00042A AK97-00608A 6602-001076 AK66-00041A AK66-00045A AK63-00101A AK92-00328A AK73-00005B AH61-50327A AK66-00043A AK66-00044A AK61-00032A AK31-00014A AK64-00491A AK31-00005A AK97-00638A AK61-00253A AK41-00156A 6003-001157 6001-001370 6002-001086
Description ; Specification CLAMPER-ASSY;DP-5,POM,-,-,-,-,BLK,GEAR-PULLEY;DP-15,POM,-,-,-,WHT,-,-,ASSY-MOTOR LOAD;-,DP-15,BELT-RECTANGULAR;CR,T1.2,4.3%,1.2X25.1,B GEAR-TRAY;DP-15,POM,-,-,-,WHT,-,-,SLIDER HOUSING;DP-15,POM,-,W17.8,L90,WHT TRAY-DISC;DP-15,ABS,-,W120,L186.3,-,BLK, ASSY PCB-DECK;DP-15,RUBBER-INSULATOR;DP-15,BUTYL,·'12,HS30,H SHAFT-P/U;DP-3,SUS,L84.7,OD3,-,-,GEAR-FEED A;DP-15,POM,-,-,-,-,-,-,GEAR-FEED B;DP-15,POM,-,-,-,-,-,-,HOLDER-CAM SKEW;DP-9,POM,-,-,-,BLACK,MOTOR SPINDLE;DP-15,3000RPM,-,-,-,CHASSIS SUB;DP-15,POM,-,-,-,-,MOTOR-FEED ASSY;-,DP-9,-,-,-,-,-,-,-,-,ASSY-PICK UP;-,SOH-DT2,TRINO ASSY PICK U HOLDER-CHUCK;DP-15,POM,-,-,-,-,FFC-P U;DP-15,-,FFC,24,T0.3,LEFT SCREW-TAPTITE;PWH,+,B,M2,L6,ZPC(YEL),SWR SCREW-MACHINE;CH,+,M1.7,L3.0,ZPC(YEL),SW SCREW-TAPPING;PH,+,B,M1.7,L5.0,ZPC(YEL),
Remark
Samsung Electronics
3-5
Exploded Views and Parts List
MEMO
3-6
Samsung Electronics | File name 20031227092337859_CH4.pdf4. Electrical Parts List
Loc.No P001 AC100 AC18 AC19 AC20 AC21 AC22 AC23 AC24 AC25 AC26 AC27 AD1 AD2 AD3 AD4 AE10 AE11 AE12 AE13 AE14 AE15 AE16 AE3 AE5 AE8 AE9 AIC2 AIC4 AL1 AL2 AQ1 AQ2 AQ3 AQ4 AQ5 AQ6 AQ7 AQ8 AQ9 AR100 AR14 AR15 AR16 AR17 AR28 AR29 AR30 AR31 AR41 AR42 AR43 AR44 AR45 AR46 AR47 AR48 AR49 AR50 AR52 AR54 Part No AK92-00339A 2203-000426 2203-005148 2203-005148 2203-005148 2203-000315 2203-005148 2203-000125 2203-005148 2203-000315 2203-000125 2203-005148 0407-000114 0407-000114 0407-000114 0401-000008 2401-002165 2401-000913 2401-002144 2401-000913 2401-002144 2401-000414 2401-002165 2401-000913 2401-000913 2401-002165 2401-002165 1002-001294 1201-000163 3301-001419 3301-001419 0504-000128 0504-000156 0501-000341 0504-000128 0504-000156 0501-000341 0504-000128 0504-000156 0501-000314 2007-000113 2007-000090 2007-000075 2007-000075 2007-000078 2007-000090 2007-000075 2007-000075 2007-000078 2007-001179 2007-000078 2007-000092 2007-000097 2007-000097 2007-001179 2007-000078 2007-000092 2007-000097 2007-000097 2007-000078 2007-000102 Description ; Specification ASSY PCB-MAIN;DVD-P241,MAIN ASSY C-CER,CHIP;0.018NF,5%,50V,C0G,TP,1608 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,C-CER,CHIP;0.12NF,5%,50V,C0G,TP,1608 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,C-CER,CHIP;1.2nF,10%,50V,X7R,TP,1608,C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,C-CER,CHIP;0.12NF,5%,50V,C0G,TP,1608 C-CER,CHIP;1.2nF,10%,50V,X7R,TP,1608,C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,DIODE-ARRAY;DAN202K,80V,100mA,CA2-3,SOTDIODE-ARRAY;DAN202K,80V,100mA,CA2-3,SOTDIODE-ARRAY;DAN202K,80V,100mA,CA2-3,SOTDIODE-SWITCHING;DAN217,80V,100mA,SOT-23, C-AL;100uF,20%,16V,GP,TP,6.3x7,5 C-AL;22uF,20%,16V,GP,TP,5x11,5 C-AL;47uF,20%,16V,GP,TP,5x11,5 C-AL;22uF,20%,16V,GP,TP,5x11,5 C-AL;47uF,20%,16V,GP,TP,5x11,5 C-AL;10uF,20%,16V,GP,TP,4x7,5 C-AL;100uF,20%,16V,GP,TP,6.3x7,5 C-AL;22uF,20%,16V,GP,TP,5x11,5 C-AL;22uF,20%,16V,GP,TP,5x11,5 C-AL;100uF,20%,16V,GP,TP,6.3x7,5 C-AL;100uF,20%,16V,GP,TP,6.3x7,5 IC-D/A CONVERTER;PCM1742KE,24BIT,TSSOP,1 IC-OP AMP;4560,SOP,8P,173MIL,DUAL,100V/m BEAD-SMD;-,220,-,500,TP,-,0.3 BEAD-SMD;-,220,-,500,TP,-,0.3 TR-DIGITAL;-,NPN,200MW,22K/22K,SOT-23,TP TR-DIGITAL;KSR2103,PNP,200MW,22K/22K,SOT TR-SMALL SIGNAL;KSC1623-L,NPN,200mW,SOTTR-DIGITAL;-,NPN,200MW,22K/22K,SOT-23,TP TR-DIGITAL;KSR2103,PNP,200MW,22K/22K,SOT TR-SMALL SIGNAL;KSC1623-L,NPN,200mW,SOTTR-DIGITAL;-,NPN,200MW,22K/22K,SOT-23,TP TR-DIGITAL;KSR2103,PNP,200MW,22K/22K,SOT TR-SMALL SIGNAL;KSA812,PNP,150mW,SOT-23, R-CHIP;33ohm,5%,1/10W,TP,1608 R-CHIP;10Kohm,5%,1/10W,TP,1608 R-CHIP;220ohm,5%,1/10W,TP,1608 R-CHIP;220ohm,5%,1/10W,TP,1608 R-CHIP;1Kohm,5%,1/10W,TP,1608 R-CHIP;10Kohm,5%,1/10W,TP,1608 R-CHIP;220ohm,5%,1/10W,TP,1608 R-CHIP;220ohm,5%,1/10W,TP,1608 R-CHIP;1Kohm,5%,1/10W,TP,1608 R-CHIP;8.2Kohm,5%,1/10W,TP,1608 R-CHIP;1Kohm,5%,1/10W,TP,1608 R-CHIP;15Kohm,5%,1/10W,TP,1608 R-CHIP;47Kohm,5%,1/10W,TP,1608 R-CHIP;47Kohm,5%,1/10W,TP,1608 R-CHIP;8.2Kohm,5%,1/10W,TP, | File name 20031227092337859_CH5.pdf5. Block Diagram
DECK ASS'Y (DP-15)
Remote Control ZIC2 SDRAM Pick-up & I/V Amp ZIC5 2KBit EEROM
Spindle Motor
Feed Motor
RIC1 (SP3723) RF Amp & DPD CSS INPUT FIFO & DEMUX
ZIC1 (Vaddis-6) A/V Decoder
DTS Bitstream
Optical
IEC958/1937
Coaxial Lt Rt
AUDIO DSP
Down-L/R
AIC2 (PCM1742) 2-CH Audio DAC
Post Filter Post Filter
FIC1 (FAN8004) Actuator & Motor Driver A/V Decoder AC3 & MPEG 5.1
Compo
VIC1 (LA73054)
CVBS Yout Cout
Y/B/Pb
Video Encoder (4DAC)
6dB AMP
C/R/Pr
Post Filter 6dB AMP
R/Pr B/Pb G/Y
Comp/G/Y
Samsung Electronics
This Document can not be used without Samsung's authorization.
5-1
Block Diagram
MEMO
5-2
This Document can not be used without Samsung's authorization.
Samsung Electronics | File name 20031227092337859_CH6.pdf6. Schematic Diagrams
6-1 Power - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-2 AV-Decoder/Main-Micom - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-3 Servo - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-4 Video - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-5 Audio - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-6 Key - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-2 6-3 6-4 6-5 6-6 6-7
Block Identification of PCB
Main PCB (Component Side)
Samsung Electronics
This Document can not be used without Samsung's authorization.
6-1
Schematic Diagrams
6-1 Power
6-2
This Document can not be used without Samsung's authorization.
Samsung Electronics
Schematic Diagrams
6-2 AV-Decoder/Main-Micom
Samsung Electronics
This Document can not be used without Samsung's authorization.
6-3
Schematic Diagrams
6-3 Servo
6-4
This Document can not be used without Samsung's authorization.
Samsung Electronics
Schematic Diagrams
6-4 Video
Samsung Electronics
This Document can not be used without Samsung's authorization.
6-5
Schematic Diagrams
6-5 Audio
6-6
This Document can not be used without Samsung's authorization.
Samsung Electronics
Schematic Diagrams
6-6 Key
Samsung Electronics
This Document can not be used without Samsung's authorization.
6-7
Schematic Diagrams
MEMO
6-8
This Document can not be used without Samsung's authorization.
Samsung Electronics | File name 20031227092337859_COVER.pdfDVD PLAYER
Chassis : Trino DVD-P241
SERVICE MANUAL DVD-P241
SERVICE
DVD PLAYER
Manual
CONTENTS 1. Precautions 2. Alignment and Adjustment 3. Exploded Views and Parts List 4. Electrical Parts List 5. Block Diagram 6. Schematic Diagrams
If you want to know additional information which is not included on this Service Manual, please refer to the DVD-P241 Training Manual (AK82-00419A).
ELECTRONICS
STANDBY/ON
EZ VIEW
LOADING
This Service Manual is a property of Samsung Electronics Co.,Ltd. Any unauthorized use of Manual can be punished under applicable international and/or domestic law.
© Samsung Electronics Co., Ltd. DEC. 2003 Printed in Korea AK82-00418A | File name 27095303843_CH1.pdf1. Precautions
1-1 Safety Precautions
1) Before returning an instrument to the customer, always make a safety check of the entire instrument, including, but not limited to, the following items: (1) Be sure that no built-in protective devices are defective or have been defeated during servicing. (1)Protective shields are provided to protect both the technician and the customer. Correctly replace all missing protective shields, including any removed for servicing convenience. (2)When reinstalling the chassis and/or other assembly in the cabinet, be sure to put back in place all protective devices, including, but not limited to, nonmetallic control knobs, insulating fish papers, adjustment and compartment covers/shields, and isolation resistor/capacitor networks. Do not operate this instrument or permit it to be operated without all protective devices correctly installed and functioning. (2) Be sure that there are no cabinet openings through which adults or children might be able to insert their fingers and contact a hazardous voltage. Such openings include, but are not limited to, excessively wide cabinet ventilation slots, and an improperly fitted and/or incorrectly secured cabinet back cover. (3) Leakage Current Hot Check-With the instrument completely reassembled, plug the AC line cord directly into a 120V AC outlet. (Do not use an isolation transformer during this test.) Use a leakage current tester or a metering system that complies with American National Standards institute (ANSI) C101.1 Leakage Current for Appliances and Underwriters Laboratories (UL) 1270 (40.7). With the instrument's AC switch first in the ON position and then in the OFF position, measure from a known earth ground (metal water pipe, conduit, etc.) to all exposed metal parts of the instrument (antennas, handle brackets, metal cabinets, screwheads, metallic overlays, control shafts, etc.), especially any exposed metal parts that offer an electrical return path to the chassis. Any current measured must not exceed 0.5mA. Reverse the instrument power cord plug in the outlet and repeat the test. See Fig. 1-1. Any measurements not within the limits specified herein indicate a potential shock hazard that must be eliminated before returning the instrument to the customer.
(READING SHOULD NOT BE ABOVE 0.5mA) DEVICE UNDER TEST TEST ALL EXPOSED METER SURFACES 2-WIRE CORD ALSO TEST WITH PLUG REVERSED (USING AC ADAPTER PLUG AS REQUIRED) EARTH GROUND
LEAKAGE CURRENT TESTER
Fig. 1-1 AC Leakage Test
(4) Insulation Resistance Test Cold Check-(1) Unplug the power supply cord and connect a jumper wire between the two prongs of the plug. (2) Turn on the power switch of the instrument. (3) Measure the resistance with an ohmmeter between the jumpered AC plug and all exposed metallic cabinet parts on the instrument, such as screwheads, antenna, control shafts, handle brackets, etc. When an exposed metallic part has a return path to the chassis, the reading should be between 1 and 5.2 megohm. Whe | File name 27095303843_CH10.pdf
10. Wiring Diagram
Samsung Electronics
10-1
Block Diagram
MEMO
10-2
Samsung Electronics | File name 27095303843_CH11.pdf11. Schematic Diagrams
11-1 Power - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 11-2 AV-Decoder/Main-Micom - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 11-3 Servo - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 11-4 Video - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 11-5 Audio - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 11-6 Key - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 11-2 11-3 11-4 11-5 11-6 11-7
Block Identification of PCB
Main PCB (Component Side)
Samsung Electronics
This Document can not be used without Samsung's authorization.
11-1
Schematic Diagrams
11-1 Power
11-2
This Document can not be used without Samsung's authorization.
Samsung Electronics
Schematic Diagrams
11-2 AV-Decoder/Main-Micom
Samsung Electronics
This Document can not be used without Samsung's authorization.
11-3
Schematic Diagrams
11-3 Servo
11-4
This Document can not be used without Samsung's authorization.
Samsung Electronics
Schematic Diagrams
11-4 Video
Samsung Electronics
This Document can not be used without Samsung's authorization.
11-5
Schematic Diagrams
11-5 Audio
11-6
This Document can not be used without Samsung's authorization.
Samsung Electronics
Schematic Diagrams
11-6 Key
Samsung Electronics
This Document can not be used without Samsung's authorization.
11-7
Schematic Diagrams
MEMO
11-8
This Document can not be used without Samsung's authorization.
Samsung Electronics | File name 27095303843_CH2.pdf2. Reference Information
2-1 Introduction to DVD
2-1-1 The Definition of DVD
DVD is the next generation medium and is the acronym of the Digital Versatile Disc or thr Digital Video Disc, which maximizes the saving density of the disk surface using the MPEG-2 compression technology to enable the storage of 17G bytes of data on the same size CD. 1) 7 times the storage capacity of the conventional CD Minimized the track pitch and pit size to 1/2 of conventional CD. Uses red laser with short-wavelenght of 650nm (635nm). DVD Vs. CD-ROM DVD Single-Layer Laser Wavelength Track Pitch Disc Diameter Disc Thickness Linear Velocity 1.2 (0.6 x 2) mm 3.49m/s 3.84m/s Dual-Layer 780nm 1.6um 120mm 1.2mm 1.2 ~ 1.4m/s
CD-ROM
650nm (635nm) 0.75um
2) Disc Formats DVD consists of two 0.6mm discs attached together, enabling access to the upper and lower side of the disk, and 4 sides could be used at maximum.
Single Layer : 4.7GByte Label Polycarbonate Bonding layer Reflective layer Polycarbonate
Dual Layer : 8.5GByte Label Polycarbonate Reflective layer Bonding layer Semi-reflective layer Polycarbonate Dual Side Dual Layer : 17GByte Polycarbonate Semi-reflective layer Reflective layer Bonding layer Reflective layer Semi-reflective layer Polycarbonate
Dual Side Single Layer : 9.5GByte Polycarbonate Reflective layer Bonding layer Reflective layer Polycarbonate
Samsung Electronics
2-1
Reference Information
2-1-2 DVD Types
FORMAT DVD-Video DVD-ROM DVD-Audio DVD-R DVD-RAM TYPE Playback Only Read Only Playback Only 1 Time Recording Rewritable APPLICATIONS High quality image and sound for movies and other video media. Multi-functional, multi-midia software that requires large storage capacity. High quality sound that exceeds the CD, multi-channel Audio. Storage media for the computer. Data access/storage media for the computer.
2-2
Samsung Electronics
Reference Information
2-2 DVD-Video Fromat
2-2-1 Main Features
1) Able to store up to 160 minutes of Movie by utilizing the MPEG-2 compression technology. ( Aver. 133min.) 2) Enables more than 500 lines of horizontal resolution. (Class corresponding to the Master Tapes used in broadcasting stations) 3) Provides Dolby Digital 5.1ch Surround 3D sound, which enables theater quality sound (NTSC area). For PAL areas, 1 of either MPEG-2 Audio or Dolby Digital must be selected. 4) Multi-Language Able to store up to 8 languages of dubbing. Able to store up to 32 subtitle languages. 5) Milti-Aspect Ratio 3TV Mode alternatives ; 16:9 Wide Screen (DVD Basic)/4:3 Pan & Scan/Letter Box. 6) Multi-Story Possible to implement Interactive Viewing which enables the user to select the scenario. 7) Multi-Angle Able to view the camera angle you selected among the scenes recorded with multiple camera angles. Note ; The above media features must have the DVD Title that contains the appropriate contents to function properly.
2-2-2 Audio & Video Specifications
Classification Compression Pixel VIDEO Horizontal resolution Compression | File name 27095303843_CH3.pdf3. Product Specification
Power Requirements Power Consumption General Weight Dimensions Operating Temperature Range Operating Humidity Range DVD (Digital Versatile Disc) Disc CD : 5" (Compact Disc) CD : 31/2" (Compact Disc) Composite Video Component Video Video Output S-Video 2 Channel *Ferquency Response Audio Output *S/N Ratio *Dynamic Range *Total Harmonic Distortion AC120V, 60Hz 10W 4.0Ibs W 16.9 in x D 8.1 in x H 1.7 in +41°F to 95°F 10% to 75% Reading Speed : 11.45ft/sec. Approx. Play Time (Single Sided, Single Layer Disc) : 135min. Reading Speed : 3.9 to 4.6ft/sec. Maximum Play Time : 74min. Reading Speed : 3.9 to 4.6ft/sec. Maximum Play Time : 20min. 1 channel ; 1.0Vp-p (75ohm load) Y : 1.0Vp-p (75ohm load) Pr : 0.70Vp-p (75ohm load) Pb : 0.70Vp-p (75ohm load) Luminance Signal : 1.0Vp-p (75ohm load) Chrominance Signal : 0.286Vp-p (75ohm load) L(1/L), R(2/R) 48KHz Sampling : 4Hz to 22KHz 96KHz Sampling : 4Hz to 44KHz 110dB 100dB 0.004% * : Nominal specification
Samsung Electronics
3-1
Product Specification
MEMO
3-2
Samsung Electronics | File name 27095303843_CH4.pdfSamsung Electronics
General Features
SETUP
Digital Photo Viewer (JPEG) You can view Digital Photos on your TV.
Disc Type and Characteristics
This DVD player is capable of playing the following types of discs with the corresponding logos:
Excellent Sound Dolby Digital, a technology developed by Dolby Laboratories, provides crystal clear sound reproduction. Repeat You can repeat a song or movie simply by pressing the REPEAT button.
Screen Both regular and widescreen(16:9) pictures can be viewed.
Disc Types (Logos) Recording Disc Size Max. Playing Time Types Characteristics
5" Audio + Video 31/2"
4. Operating Instructions
Slow Motion An important scene can be viewed in slow motion. Instant Replay This function is used to replay the previous 10 seconds of the movie from the current position.
MP3 This unit can play discs created from MP3 files.
DVD
Programmed Play You can program tracks to play in desired order. (CD) Instant Skip This function skips playback ahead 10 seconds.
Single-sided · DVD contains excellent 240 min. sound and video due to Double-sided Dolby Digital and MPEG-2 480 min. system. Single-sided · Various screen and audio functions can be easily 80 min. Double-sided selected through the onscreen menu. 160 min. 74 min.
AUDIO-CD
5" Audio
Parental Control The parental control allows users to set the level necessary to prohibit children from viewing harmful movies such as those with violence, adult subject matter, etc. NOTE
31/2" * Discs which cannot be played with this player.
20 min.
· CD is recorded as a Digital Signal with better audio quality, less distortion and less deterioration of audio quality over time.
Various On-Screen Menu Functions You can select various languages (Audio/Subtitle) and screen angles while enjoying movies.
· DVD-ROM · DVD-RAM · CD-ROM · CDV · CDI · HD layer of super Audio CD · CDGs play audio only, not graphics.
Disc Markings
~
Progressive Scan Progressive scanning creates an improved picture with double the scan lines of a conventional interlaced picture.
* Ability to play back may depend on recording conditions. · DVD-R, +R · DVD+RW, -RW * It may not play CD-R, CD-RW and DVD-R in all cases due to the type of disc or condition of the recording. · CD-RW · Play Region Number
NTSC
· NTSC broadcast system in U.S.A, Canada, Korea, Japan, etc. · Dolby Digital disc
STEREO
· Stereo disc
EZ VIEW Easy View can convert Letter Box images to full screen viewing on your conventional TV.
DIGITAL SOUND
COPY PROTECTION
· Digital Audio disc
· DTS disc
· MP3 disc
· Many DVD discs are encoded with copy protection. Because of this, you should only connect your DVD player directly to your TV, not to a VCR. Connecting to a VCR results in a distorted picture from copy-protected DVD discs.
Play Region Number
Both the DVD player and the discs are coded by region. These regional codes must match in order for the disc to play. If the codes do not match, the disc will not play. The Region Number for this playe | File name 27095303843_CH5.pdf5. Disassembly and Reassembly
5-1 Cabinet and PCB
Note : Reassembly in reverse order.
5-1-1 Top Cabinet Removal
1) Remove 3 Screws OE on the back Top Cabinet. 2) Lift up the Top Cabinet in direction of arrow.
OE 3 SCREWS
Fig. 5-1 Top Cabinet Removal
Samsung Electronics
5-1
Disassembly and Reaasembly
5-1-2 Door-Tray Removal
1) Supply power and open Tray OE. 2) Disassemble the Door-Tray ´ in direction of arrow "A". 3) Close Tray OE and power off. Note : If Tray OE doesn't open, insert a Screw driver ¨ into the Emergency hole (as shown in detailed drawing) and then push it in the direction of arrow "B". Open Tray manually.
OE TRAY ´ DOOR-TRAY
"B"
"A"
¨ SCREW DRIVER EMERGENCY HOLE Fig. 5-2 Door-Tray Removal
5-2
Samsung Electronics
Disassembly and Reaasembly
5-1-3 Ass'y Front-Cabinet Removal
1) Release 6 Hooks OE, ´, , ¨ and Ass'y Front-Cabinet ^.
´ 1 HOOK OE 2 HOOKS
¨ 2 HOOKS
1 HOOK
^ ASS'Y FRONT-CABINET Fig. 5-3 Ass'y Front-Cabinet Removal
Samsung Electronics
5-3
Disassembly and Reaasembly
5-1-4 Ass'y Deck Removal
1) Disconnect Flat-Cable from DCN1, DCN2 on Main PCB. 2) Remove 3 Screws OE from the Ass'y Deck and lift it up. OE 3 SCREWS
FLAT-CABLE
ASS'Y-DECK
DCN1 DCN2
Fig. 5-4 Ass'y Deck Removal
5-4
Samsung Electronics
Disassembly and Reaasembly
5-1-5 Main PCB Removal
1) Remove 4 Screws OE. 2) Lift up the Main PCB ´. OE 4 SCREWS
´ MAIN PCB
Fig. 5-5 Main PCB Removal
Samsung Electronics
5-5
Disassembly and Reaasembly
5-2 Deck
5-2-1 Holder Chuck Removal
1) Push 4 Hooks OE in the direction of arrow "A" and lift up the Holder Chuck ´. OE 2 HOOKS "A" ´ HOLDER CHUCK
OE 2 HOOKS
"A"
Fig. 5-6 Holder Chuck Removal
5-6
Samsung Electronics
Disassembly and Reaasembly
5-2-2 Tray Disc Removal
1) Insert a Screw Driver OE into Emergency Hole ´ and push the Slider Housing in the direction arrow "A". 2) When the Tray Disc ¨ comes out a little, pull it in the direction arrow "B" by hand. SLIDER HOUSING
¨ TRAY DISC "B" "A" ´ EMERGENCY HOLE OE SCREW DRIVER
Fig. 5-7 Tray Disc Removal
Samsung Electronics
5-7
Disassembly and Reaasembly
5-2-3 Assy P/U Deck Removal
1) Remove the 4 Soldering OE (SL+, SL-, SP+, SP-). 2) Remove the 1 Screw ´ and lift up the Ass'y P/U Deck in the direction arrow "A". 3) When the Ass'y P/U Deck lift up a little, push Chassis Sub in the direction of arrow "B" and lift up the Ass'y P/U Deck . ´ 1 SCREW
"B"
"A"
ASS'Y P/U DECK ¨ CHASSIS SUB
"B"
OE 4 SOLDERING
SP + (RED) SP - (BLK) SL - (BLK) SL + (RED) TM - (BLK) TM + (BLK)
Fig. 5-8 Assy P/U Deck Removal
5-8
Samsung Electronics
Disassembly and Reaasembly
5-2-4 Ass'y Housing Removal
1) Remove the 2 Soldering OE. (TM+, TM-) 2) Push the 2 Hooks ´ in the direction of arrow "A" and remove Ass'y PCB Deck . 3) Push the Slider Housing ¨ in the direction arrow "B". 4) Push the 1 Hook ^ in the direction of arrow "C" and lift up the Slider Housing ¨. 5) Remove the Belt Pulley Ø and 2 Screws , Ass'y Motor Load ". 6) Push the 1 Ho | File name 27095303843_CH6.pdf6. Alignment and Adjustment
6-1 Location of Test Point
Pin 29 of RIC1
Fig. 6-1 Location of Test Point Samsung Electronics 6-1
Alignment and Adjustment
6-2 Skew Adjustment
6-2-1 Adjustment Spec. and Test Point
Test Disc TDV-533 Chapter 14 Adjustment Spec. Flat Waveform Test Point "Pin 29 of RIC1" (Main PCB - Component Side) (See Fig. 6-1) Test Disc ; Service not Available Adjustment Location Screw A / B Ass'y Deck - Top Side (See Fig. 6-2)
Fig. 6-2 Ass'y Deck (Top Side)
6-2
Samsung Electronics
Alignment and Adjustment
6-2-2 SKEW Adjustment Method
Needed to minimize the variations in Skew of the Pickup unit and to provide optimum match with the recorded signal on the Disc. 1) Connect an Oscilloscope to the "Pin 29 of RIC1" Test Point (See Fig. 6-1). 2) Connect Power, Open the Tray and Play the TDV-533 Disc, Chapter 14. Set the Oscilloscope Range as follows : (Voltage ; 20mV/Div., Frequency ; 10m Sec.) 3) Adjust the Screws "A" and "B" (See Fig. 6-2) using a Hex screwdriver until you obtain a Flat Waveform and the picture is stable. Then, go to Chapter 1 and make sure the Waveform is Flat here as well. If not, you have to go back to Chapter 14 and adjust again. If you cannot obtain a Flat waveform, then the unit is defective. Note : The Deck must be in a horizontal position. Use both "A" and "B" screws to adjust.
Typical Waveform before Adjustment
Waveform after Correct Adjustment
Fig. 6-3 Envelope Waveform
Samsung Electronics
6-3
Alignment and Adjustment
MEMO
6-4
Samsung Electronics File name 27095303843_CH7.pdf7. Circuit Operating Descriptions
7-1 Power
7-1-1 Comparsion between Linear Power Supply and S.M.P.S.
7-1-1 (a) Linear
Vout REGULATOR + Vp (Np) + Vs (Ns) + Vreg
Common power (Ex.120V 60Hz)
Fig. 7-1 Linear Power Supply Waveform/Description Vp
0
t
Input : Common power to transformer (Vp).
Fig. 7-2 Vs The output Vs of transformer is determined by the ratio of 1st Np and 2nd Ns. Vs = (Ns/Np) x Vp
0
t
Fig. 7-3 Vout
0
t
Vout is output (DC) by diode and condensor.
Fig. 7-4 Samsung Electronics 7-1
Circuit Operating Descriptions
Advantages and disadvantages of linear power supply 1) Advantages : Little noise because the output waveform of transformer is sine wave. 2) Disadvantages : OE Additional margin is required because Vs is changed (depending on power source). (The regulator loss is caused by margin design). ´ Greater core size and condensor capacity are needed, because the transformer works on a single power frequency. v Vout
Change by common power
Vreg
0 Regulator loss Fig. 7-5
t
7-1-1 (b) S.M.P.S. (Ringing Choke Converter methol)
Transformer (Np) (Ns) + + (Vp) (Vs) + + Vin Switch + Vs switch I switch
Vout REGULATOR
Vreg
ON/OFF Control
Fig. 7-6 Terms 1) 1st : Common power input to 1st winding. 2) 2nd : Circuit followings output winding of transformer. 3) f (Frequency) : Switching frequency (T : Switching cycle) 4) Duty : (Ton/T) x 100
7-2
Samsung Electronics
Circuit Operating Descriptions
7-1-2 Circuit description [FLY-Back RCC(Ringing Choke Converter)] Control
7-1-2 (a) AC Power Rectification/Smoothing Terminal
1) PDS01, PDS02, PDS03, PDS04 : Convert AC power to DC(Full wave rectification). 2) PEF10 : Smooth the voltage converted to DC. 3) PLS01, PBS01 : Noise removal at power input/output. 4) PVA1 : SMPS protection at power surge input.
7-1-2 (b) SNUBBER Circuit : PDS11, PCD12, PER13, PRS13
Vswitch Inverted power by leakage inductance
dt
1) Prevent residual high voltage at the terminals of switch during switch off/Suppress noise. High inverted power occurs at switch (PQR11) off, because of the 1st winding of transformer : (V=-L1 xdi/dt. L1 : Leakage Induction) A very high residual voltage exist on both terminals of PQR11 because dt is a very short. 2) SNUBBER circuit protects PQR11 from damage through leakage voltage suppression by RC, (Charges the leakage voltage to PDS11, PER13, PCD12 and discharges to PRS13).
0 Toff
t
Fig. 7-7
7-1-2 (c) Driving circuit
When Vin supplied, driving current Ig occurs throuhg the PRR11. By this IC (=Hfe x Ig) occurs throug the PQR11 and the Vb is inducted to base winding coil NB of PQR11. By inducted Vb, Ib start flow and the PQR11 is saturated (S/W ON). Ib is constant and Ic increases in Proportion to time. After constant time passed Ib become to shortage and PQR11 is cut OFF (S/W OFF).
Fig. 7-8 Driving Circuit
Samsung Electronics
7-3
Circuit Operating Descriptions
7-1-2 (d) Feedback Control Circuit
A K
Fig. 7-9 Operation descriptions 1) Internal OP-Amp `+' | File name 27095303843_CH8.pdfNo focus incoming No pick-up home positing
Samsung Electronics
Check RIC1 and A, B, C, D input. ZIC1-191(SLED-PWM) output is normal? (1.7V ~ 1.8V) No Check ZIC1. Yes No Check FIC1. SLED+, SLEDFIC1-32, 33 output are normal? Yes Check FIC1. Check the Sled Motor and connection.
A
8. Troubleshooting
FE in ZIC1-181 is within specified range?
No
Yes
FIC1-27, 28 output are normal?
No
Yes
Check open state from FIC1 to pick-up.
8-1
8-2
No Search Operation No No MEVO, RIC1-32 output level is normal? Check RIC1 MIRR, RIC1-27 output is normal? Yes Yes Check pick-up. Check RIC1 peripheral circuit. Actual velocity occurs at ZIC1-191 terminal? Open check in related circuit. Yes No Check ZIC1 peripheral circuit. Actual velocity occurs at FIC1-32, 33 terminal? Yes No Check FIC1 peripheral circuit. TE occurs in search range? No Focus On? No A Yes See "Fine Seek Check"
NO LD CD ON
Troubleshooting
B
RIC1-21 is 5V?
No
Yes
Divide RQ2 emitter terminal voltage and 5V real voltage difference into 10ohm.
Yes
Current exceeds 0.1A?
No
Yes
LD out pick-up replace.
Samsung Electronics
Samsung Electronics
Abnormal rotation of disc motor Input of RF SUM signal is normal? (ZIC1-172, 173) No RIC1-54, 55 output is normal? Yes Check RIC1 peripheral circuit and A, B, C, D. Check path to RIC1 and ZIC1. SPD output is normal? (ZIC1-189) Yes Check ZIC1 peripheral circuit. ZIC1-169(TRD) output is normal? No No No Yes Yes Check RIC1-39 terminal. FIC1-36, 35(T+, T-) terminal outputs are normal? No Yes Check FIC1 peripheral circuit. FIC1-35 output is normal? Yes No Check FIC1 soldering and power. FIC1-22 signal MON is "H" ? Yes No Check ZIC1. Check or replace disc motor.
FINE SEEK Check
FINE SEEK MIRR signal (RIC1-27) is missing?
Yes
Check RIC1 Peripheral curcuit.
No
Track incomming is delayed?
No
Time out due to many jump counts.
Yes
TE is within 2V and 3V?
No
Yes
Pick-up transfer smooth.
No
Yes
Check Deck.
Check SIC1 peripheral circuit.
Check DCN1 and pick-up.
Troubleshooting
8-3
8-4
CD/VCD/DVD L/R output error (Mixed Audio output) No Check ZIC1 perpheral circuit. Yes Normal DATA 0 is input in AIC2-2? Check ZIC1-113 output. No Analog output of AIC2-7, 8(Vout) is normal? No No Check FIC1 perpheral circuit. Yes Check ZIC1-118 (CD/VCD ; 16.9344MHz, DVD ; 18.432MHz) AIC4-1, 7 output is normal? Yes No Check AIC4 peripheral circuit. Base terminal level of AQ1, AQ3 are "L"? Yes No Check ZIC1-106 mute. Check JACK1 peripheral soldering shot.
Troubleshooting
No Tray open/close
ZIC1-147, 149 Open ; "L" Close ; "H"
Yes
Check FIC1-14, 15 output at OPEN/CLOSE.
Yes
Check signal line state from FIC1-14, 15 to tray motor.
Samsung Electronics
S-Video output error
Y/Pr/Pb output error
Samsung Electronics
Select video output to "S-VIDEO". Select video output to "525I". Video output of display setup is "525I". Yes C No
Video output of display setup is "S-VIDEO".
No
Yes
C
Troubleshooting
8-5
8-6
CVBS output error C Pin of VDDP in ZIC1 has normal l | File name 27095303843_CH9.pdf9. Block Diagram
DECK ASS'Y (DP-15)
Remote Control ZIC2 SDRAM Pick-up & I/V Amp ZIC5 2KBit EEROM
Spindle Motor
Feed Motor
RIC1 (SP3723) RF Amp & DPD CSS INPUT FIFO & DEMUX
ZIC1 (Vaddis-6) A/V Decoder
DTS Bitstream
Optical
IEC958/1937
Coaxial Lt Rt
AUDIO DSP
Down-L/R
AIC2 (PCM1742) 2-CH Audio DAC
Post Filter Post Filter
FIC1 (FAN8004) Actuator & Motor Driver A/V Decoder AC3 & MPEG 5.1
Compo
VIC1 (LA73054)
CVBS Yout Cout
Y/B/Pb
Video Encoder (4DAC)
6dB AMP
C/R/Pr
Post Filter 6dB AMP
R/Pr B/Pb G/Y
Comp/G/Y
Samsung Electronics
This Document can not be used without Samsung's authorization.
9-1
Block Diagram
MEMO
9-2
This Document can not be used without Samsung's authorization.
Samsung Electronics | File name 27095303843_COVER.pdfDVD PLAYER
Chassis : Trino DVD-P241
TRAINING MANUAL DVD-P241
TRAINING
DVD PLAYER
Manual
CONTENTS 1. Precautions
ELECTRONICS
2. Reference Information 3. Product Specification 4. Operating Instructions 5. Disassembly and Reassembly 6. Alignment and Adjustment 7. Circuit Operating Description 8. Troubleshooting
STANDBY/ON EZ VIEW LOADING
9. Block Diagram 10. Wiring Diagram 11. Schematic Diagrams
This Service Manual is a property of Samsung Electronics Co.,Ltd. Any unauthorized use of Manual can be punished under applicable international and/or domestic law.
© Samsung Electronics Co., Ltd. DEC. 2003 Printed in Korea AK82-00419A |
>> Download document <<
 Attention! This manual is multipart. Download all, before decompressing
Average rating for this file: 0.00 ( from 0 votes) Similar Service Manuals : - - - - - - -
-
-
-
-
script execution: 0.49 s
|
|