NISSAN ALTIMA 2000 free download

File name em.pdf

ENGINE MECHANICAL SECTION EM GI MA EM CONTENTS PRECAUTIONS ... 2 Parts Requiring Angular Tightening ... 2 Liquid Gasket Application Procedure... 2 PREPARATION... 3 Special Service Tools... 3 Commercial Service Tools ... 6 NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING ... 8 NVH Troubleshooting Chart -- Engine Noise ... 9 OUTER COMPONENT PARTS ... 10 COMPRESSION PRESSURE... 13 Measurement of Compression Pressure ... 13 OIL PAN ... 15 Removal ... 15 Installation ... 17 TIMING CHAIN ... 19 Removal ... 21 Upper Timing Chain... 21 Idler Sprocket ... 22 Lower Timing Chain... 22 Inspection... 23 Installation ... 24 Lower Timing Chain... 24 Upper Timing Chain... 24 OIL SEAL REPLACEMENT ... 26 Valve Oil Seal ... 26 Front Oil Seal... 26 Rear Oil Seal ... 27 ACCEL-DRUM UNIT... 28 Adjustment ... 28 CYLINDER HEAD... 30 Removal ... 31 Installation ... 31 Disassembly... 32 Inspection... 32 Cylinder Head Distortion ... 32 Camshaft Visual Check ... 33 Camshaft Runout... 33 Camshaft Cam Height ... 33 Camshaft Journal Clearance ... 33 Camshaft End Play... 34 Camshaft Sprocket Runout ... 34 Valve Guide Clearance... 34 Valve Guide Replacement ...

File name fa.pdf

FRONT AXLE & FRONT SUSPENSION GI SECTION FA MA EM LC CONTENTS PRECAUTIONS AND PREPARATION... 2 Precautions ... 2 Special Service Tools... 2 Commercial Service Tools ... 3 NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING. ... 4 NVH Troubleshooting Chart... 4 FRONT SUSPENSION SYSTEM ... 5 ON-VEHICLE SERVICE ... 6 Front Axle and Front Suspension Parts ... 6 Front Wheel Bearing... 7 Front Wheel Alignment ... 7 Drive Shaft ... 10 FRONT AXLE ... 11 Wheel Hub and Knuckle ... 12 Drive Shaft ... 16 FRONT SUSPENSION ... 24 Coil Spring and Strut Assembly... 25 Stabilizer Bar... 26 Transverse Link and Lower Ball Joint ... 27 SERVICE DATA AND SPECIFICATIONS (SDS) ... 29 General Specifications ... 29 Inspection and Adjustment... 29 EC FE CL MT AT FA RA BR ST RS BT HA EL IDX PRECAUTIONS AND PREPARATION Precautions q q q SBR686C q When installing rubber parts, final tightening must be carried out under unladen condition* with tires on ground. *: Fuel, radiator coolant and engine oil full. Spare tire, jack, hand tools and mats in designated positions. After installing suspension parts, check wheel alignment and adjust if necessary. Use flare nut wrench when removing or installing brake tubes. Always torque brake lines when installing. Special Service Tools The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here. Tool number (Kent-Moore No.) Tool name HT72520000 (J25730-A) Ball joint remover Description Removing tie-rod outer end and lower ball joint NT146 KV38106700 (J34296) KV38106800 (J34297) Differential side oil seal protector Installing drive shaft NT147 LH: KV38106700 RH: KV38106800 FA-2 PRECAUTIONS AND PREPARATION Commercial Service Tools Tool name Attachment Wheel Alignment Description Measure wheel alignment a: b: c: d: e: Screw m24 x 1.5 35 mm (1.38 in) dia. 65 mm (2.56 in) dia. 56 mm (2.20 in) 12 mm (0.47 in) GI MA EM LC EC NT148 1 Flare nut crowfoot 2 Torque wrench Removing and installing brake piping NT360 a: 10 mm (0.39 in) FE Spring compressor Removing and installing coil spring CL NT717 MT AT FA RA BR ST RS BT HA EL IDX FA-3 NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLE

File name fe.pdf

ACCELERATOR CONTROL, FUEL & EXHAUST SYSTEMS GI SECTION FE MA EM LC CONTENTS PREPARATION... 2 Special Service Tool ... 2 Commercial Service Tool ... 2 ACCELERATOR CONTROL SYSTEM ... 3 Accelerator Control System ... 3 Adjusting Accelerator Wire... 3 FUEL SYSTEM ... 4 Fuel Tank ... 4 FUEL PUMP AND GAUGE ... 5 EXHAUST SYSTEM ... 6 Exhaust System ... 7 EC FE CL MT AT FA RA BR ST RS BT HA EL IDX PREPARATION Special Service Tool The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here. Tool number (Kent-Moore No.) Tool name KV999G0010 (J38879) Fuel tank lock ring socket NT057 Description Removing and installing fuel tank lock ring KV10114400 (J38365) Heated Oxygen Sensor Wrench Loosening or Tightening rear heated oxygen sensor. NT636 Commercial Service Tool Tool name (Kent-Moore No.) Oxygen sensor thread cleaner (J-43897-18) (J-43897-12) Description Reconditioning the exhaust system threads before installing a new oxygen sensor. Use with anti-seize lubricant. a: J-43897-18 18mm diameter, for zirconia oxygen sensor. b: J-43897-12 12mm diameter, for titania oxygen sensor. AEM488 Anti-seize lubricant Permatex 133AR or equivalent meeting MIL specification MIL-A-907 Lubricating oxygen sensor thread cleaning tool when reconditioning exhaust system threads. AEM489 FE-2 ACCELERATOR CONTROL SYSTEM Accelerator Control System CAUTION: GI q When removing accelerator wire, mark initial position of lock nut. q Check that throttle valve opens fully when accelerator pedal is fully depressed. Check that throttle valve returns to idle position when accelerator pedal is released. MA q Check accelerator control parts for improper contact with any adjacent parts. q When connecting accelerator wire, be careful not to twist or scratch wire. q Refer to ``AUTOMATIC SPEED CONTROL DEVICE (ASCD)'' in EL-157 section for ASCD wire EM adjustment. LC EC FE CL MT AT FA RA BR ST RS WFE002 BT HA Adjusting Accelerator Wire SFE248AB CAUTION: q Make sure the ASCD wire is not pulling the throttle EL drum. q For ASCD wire adjustment, refer to EL-157 section IDX [``AUTOMATIC SPEED CONTROL DEVICE (ASCD)'']. 1. Loosen lock nut and tighten adjusting nut until throttle drum starts to move. 2. From that position turn back adjusting nut 1.5 to 2 turns, and tighten lock nut. FE-3 FUEL SYSTEM Fuel Tank WARNING: When replacing fuel line parts, be sure to observe the following: q Put a ``CAUTION: FLAMMABLE'' sign in workshop. q Do not smoke while servicing fuel system. Keep

File name foldout.pdf

SUPER MULTIPLE JUNCTION (SMJ) INSTALLATION To install SMJ, tighten bolts until orange ``fulltight'' mark appears and then retighten to specified torque as required. : 3 - 5 Nm (0.3 - 0.5 kg-m, 26 - 43 in-lb) CAUTION: Do not overtighten bolts, otherwise, they may be damaged. AEL168B AEL169B SUPER MULTIPLE JUNCTION (SMJ) Terminal Arrangement AEL170B FUSE BLOCK -- Junction Box (J/B) Terminal Arrangement AEL172B FUSE AND FUSIBLE LINK BOX Terminal Arrangement WEL310 ELECTRICAL UNITS Terminal Arrangement WEL183 JOINT CONNECTOR (J/C) Terminal Arrangement AEL174B

File name fwd.pdf

Edition: August 1999 Revision: August 1999 (03) Publication No. SM0E-1L30U0 QUICK REFERENCE INDEX GENERAL INFORMATION MAINTENANCE ENGINE MECHANICAL ENGINE LUBRICATION & COOLING SYSTEMS ENGINE CONTROL SYSTEM ACCELERATOR CONTROL, FUEL & EXHAUST SYSTEMS CLUTCH MANUAL TRANSAXLE AUTOMATIC TRANSAXLE FRONT AXLE & FRONT SUSPENSION REAR AXLE & REAR SUSPENSION BRAKE SYSTEM STEERING SYSTEM RESTRAINT SYSTEM BODY & TRIM HEATER & AIR CONDITIONER ELECTRICAL SYSTEM ALPHABETICAL INDEX GI MA EM LC EC FE CL MT AT FA RA BR ST RS BT HA EL IDX MODEL L30 SERIES © 1999 NISSAN NORTH AMERICA, INC. Printed in U.S.A. All rights reserved. No part of this Service Manual may be reproduced, stored in a retrieval system, or transmitted in any form, or by any means electronic, mechanical, photocopying, recording or otherwise, without the prior written permission of Nissan North America, Inc., Gardena, California. FOREWORD This manual contains maintenance and repair procedures for the 2000 Nissan ALTIMA. In order to assure your safety and the efficient functioning of the vehicle, this manual should be read thoroughly. It is especially important that the PRECAUTIONS in the GI section be completely understood before starting any repair task. All information in this manual is based on the latest product information at the time of publication. The right is reserved to make changes in specifications and methods at any time without notice. IMPORTANT SAFETY NOTICE The proper performance of service is essential for both the safety of the technician and the efficient functioning of the vehicle. The service methods in this Service Manual are described in such a manner that the service may be performed safely and accurately. Service varies with the procedures used, the skills of the technician and the tools and parts available. Accordingly, anyone using service procedures, tools or parts which are not specifically recommended by NISSAN must first be completely satisfied that neither personal safety nor the vehicle's safety will be jeopardized by the service method selected. NISSAN NORTH AMERICA, INC. Technical Service Information Department Gardena, California PLEASE HELP MAKE THIS SERVICE MANUAL BETTER! Your comments are important to NISSAN and will help us to improve our Service Manuals. Use this form to report any issues or comments you may have regarding our Service Manuals. Please photocopy this form and type or print your comments below. Mail or fax to: Nissan North America, Inc. Technical Service Information 39001 Sunrise Drive, P.O. Box 9200 Farmington Hills, MI USA 48331 FAX: (248) 488-3910 SERVICE MANUAL: Model: VIN: Year: Production Date: PUBLICATION NO. (Please photocopy back cover): VEHICLE INFORMATION Page number(s) Please describe any issues or problems in detail: Note: Please include a copy of each page, marked with your comments. Are the trouble diagnosis procedures logical and easy to use? (circle your answer) If no, what page number(s)? Please describe the issue

File name gi.pdf

GENERAL INFORMATION SECTION GI GI MA EM LC EC CONTENTS PRECAUTIONS AND PREPARATION... 2 Precautions For Supplemental Restraint System (SRS) ``Air Bag'' And ``Seat Belt Pre-Tensioner''... 2 Precautions For Nvis (Nissan Vehicle Immobilizer System -- Nats)... 2 General Precautions ... 4 Precautions for Multiport Fuel Injection System or Engine Control System... 6 Precautions for Three Way Catalyst... 6 Precautions For Hoses ... 6 Hose Clamping ... 7 Precautions for Engine Oils ... 7 Precautions for Fuel... 8 Precautions for Air Conditioning ... 8 HOW TO USE THIS MANUAL... 9 HOW TO READ WIRING DIAGRAMS... 11 Sample/Wiring Diagram ­ EXAMPL ­ ... 11 Description ... 13 Reference Area... 18 HOW TO CHECK TERMINAL... 20 Connector and Terminal Pin Kit... 20 How to Probe Connectors ... 20 How to Check Enlarged Contact Spring of Terminal... 21 Waterproof Connector Inspection ... 22 Terminal Lock Inspection ... 22 HOW TO PERFORM EFFICIENT DIAGNOSIS FOR AN ELECTRICAL INCIDENT... 23 Work Flow ... 23 Incident Simulation Tests ... 24 Circuit Inspection ... 26 HOW TO FOLLOW FLOW CHART IN TROUBLE DIAGNOSES ... 33 How To Follow This Flow Chart... 34 CONSULT-II CHECKING SYSTEM ... 36 Function and System Application ... 36 Nickel Metal Hydride Battery Replacement... 36 Checking Equipment... 37 CONSULT-II Data Link Connector (DLC) Circuit ... 38 IDENTIFICATION INFORMATION... 39 Model Variation ... 39 Identification Number ... 40 Dimensions ... 42 Wheels and Tires ... 42 LIFTING POINTS AND TOW TRUCK TOWING... 43 Preparation... 43 Board-on Lift ...