SONY KE-42TS2U free download

File name SONY KE-42TS2U SERVICE MANUAL (9-978-750-01).pdf

KE-42TS2U SERVICE MANUAL US Model Canadian Model SPECIFICATIONS Television system: American TV standard Channel coverage: VHF: 2­13/UHF: 14­69/CATV: 1­125 Antenna: 75 external terminal for VHF/UHF Screen size (measured diagonally): 42 inches Panel System: Plasma Display panel Display resolution: 1024 dots (horizontal) x 1024 lines (vertical) VIDEO IN 1/2: S VIDEO IN (4-pin mini DIN): Y:1 Vp-p, 75 unbalanced, sync negative C:0.286 Vp-p (Burst signal), 75 VIDEO (phono jack): 1 Vp-p, 75 unbalanced, sync negative AUDIO (phono jacks): 500 mVrms (100% modulation), Impedance: 47 k VIDEO IN 3: DVI-HDTV: 1 terminal, 3.3V T.M.D.S., 50 DVI-HDTV input terminal is compliant with the EIA-861 standard and is not intended for use with personal computers. AUDIO (phono jacks): 500 mVrms (100% modulation), Impedance: 47 k VIDEO IN 4: Y:1 Vp-p, 75 , 0.3 V negative sync PB:0.7 Vp-p, 75 PR:0.7 Vp-p, 75 or G:0.7 Vp-p, 75 , Sync on Green B:0.7 Vp-p, 75 , Sync on Green R:0.7 Vp-p, 75 , Sync on Green or G:0.7 Vp-p, 75 , non Sync on Green B:0.7 Vp-p, 75 , non Sync on Green R:0.7 Vp-p, 75 , non Sync on Green HD:1­5 Vp-p VD:1­5 Vp-p AUDIO (phono jacks): 500 mVrms (100% modulation), Impedance: 47 k Power consumption: In use (Max.): 415W In standby: 2.9W Dimensions (W/H/D): 1,056 x 764 x 124 mm (41 5/8 x 30 1/8 x 5 inch) Mass: 37.5 kg (82 lbs 7 oz.) SUB WOOFER: phono jack AUDIO OUT (phono jacks): 500 mVrms (100% modulation) Headphones: Stereo minijack CONTROL S IN/OUT: minijacks Speaker: 50 x 130 mm (2 x 5 1/8 inches) x2 Supplied accessories Remote control RM-928Y (1) Batteries size AA (2) 75 coaxial cable (1) AC power cord (1) Brackets (2) Cleaning cloth (1) Operating instructions (1) Optional accessories Note that some optional accessories may be out of stock. Headphones plug adapter Connecting cables VMC-810S/820S, YC-15V/30V, RK-74A, VMC-10HG, SMF-403 Design and specifications are subject to change without notice. Speaker output: 9W x 2 Power requirement: 120 V AC, 60 Hz FLAT PANEL COLOR TELEVISION SAFETY CHECK-OUT After correcting the original service problem, perform the following safety checks before releasing the set to the customer: 1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. 2. Check the interboard wiring to ensure that no wires are "pinched" or contact high-wattage resistors. 3. Check that all control knobs, shields, covers, ground straps, and mounting hardware have been replaced. Be absolutely certain that you have replaced all the insulators. 4. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement. 5. Look for parts which, though functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement. 6. Check the line cords for cracks and abrasion. Recommend the replacement of any such