SONY KP-51HW40 free download

File name SONY KP-51HW40, 57HW40 SERVICE MANUAL RA-6 CHASSIS 11.2003 (9-965-434-09).pdf

HISTORY INFORMATION FOR THE FOLLOWING MANUAL: SERVICE MANUAL MODEL NAME REMOTE COMMANDER DESTINATION RA-6 CHASSIS CHASSIS NO. KP-51HW40 KP-51HW40 KP-57HW40 KP-57HW40 RM-Y909 RM-Y909 RM-Y909 RM-Y909 US Canadian US Canadian SCC-P65G-A SCC-P65G-A SCC-P65F-A SCC-P65F-A ORIGINAL MANUAL ISSUE DATE: 8/2001 ALL REVISIONS AND UPDATES TO THE ORIGINAL MANUAL ARE APPENDED TO THE END OF THE PDF FILE. REVISION DATE 8/2001 11/2001 1/2002 2/2002 5/2002 8/2002 12/2002 7/2003 11/2003 REVISION TYPE SUBJECT No revisions or updates are applicable at this time. Correction - 1 A Board P/N Corrected Supplement - 1 New CRT Introduced - Affects S/N's 9000001 - 90XXXXXX Supplement - 1 Reissued to show corrected Page 26 Correction - 2 U Board P/N Corrected on Electrical Parts List - Page 106 Correction - 3 Correction to Exploded View Cover parts list to indicated location and new part numbers for Screen Holders - Page 95 Correction - 4 Electrical Parts List - P/N Correction on D Board Correction - 5 Electrical Parts List - P/N Correction/Addition on G Board - Page 128-130 Supplement-2 Note added to clarify correct CRT replacement Part Number depending on S/N range COLOR REAR VIDEO PROJECTOR 9-965-434-09 SERVICE MANUAL MODEL ­­­­­­ COMMANDER ­­­­­­­­­­­­ DEST. ­­­­­­­­­­­ ­­­­­ CHASSIS NO. MODEL ­­­­­­ RA-6 CHASSIS COMMANDER ­­­­­­­­­­­­ DEST. ­­­­­­­­­­­ ­­­­­ CHASSIS NO. KP-51HW40 KP-51HW40 KP-57HW40 KP-57HW40 RM-Y909 US SCC-P65G-A RM-Y909 Canadian SCC-P65G-A RM-Y909 US SCC-P65F-A RM-Y909 Canadian SCC-P65F-A RM-Y909 KP-51HW40/57HW40 COLOR REAR VIDEO PROJECTOR KP-51HW40/57HW40 RM-Y909 RM-Y909 SAFETY CHECK-OUT ( US model only ) After correcting the original service problem, perfom the following safety checks before releasing the set to the customer: l. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. 2. Check the interboard wiring to ensure that no wires are "pinched" or contact high-wattage resistors. 3. Check that all control knobs, shields, covers, ground straps, and mounting hardware have been replaced. Be absolutely certain that you have replaced all the insulators. 4. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement. 5. Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recom mend their replacement. 6. Check the line cords for cracks and abrasion. Recommend the replacement of any such line cord to the customer. 7. Check the condition of the monopole antenna (if any). Make sure the end is not broken off, and has the plastic cap on it. Point out the danger of impalement on a broken antenna to the customer, and recommend the antenna's replacement. 8. Check the B+ and HV to see they are at the values specified. Make sure your instruments are accurate;be suspicious of you