SAMSUNG ch.KS3A CW29K86V free download

File name 01_Cover.pdf

COLOR TELEVISION RECEIVER Chassis : KS3A(P)_50Hz(REV. 4) Model : CW25C33WS8XXEG CW28C73WS8XXEG CW28C93WS8XXEG CW29K84VS8XXEC CW29K86VS8XXEC WS32W66VS8XXEC COLOR TELEVISION RECEIVER CONTENTS 1. Precautions 2. Reference Information 3. Specifications 4. Alignment and Adjustments 5. Troubleshooting 6. Exploded Views and Parts List 7. Electrical Parts List 8. Block Diagrams 9. Wiring Diagram 10. Schematic Diagrams ELECTRONICS © Samsung Electronics Co., Ltd. MAR. 2002 Printed in Korea 3KS3A-50-SEH-0418

File name 02_Precaution.pdf

Precautions 1. Precautions Follow these safety, servicing and ESD precautions to prevent damage and protect against potential hazards such as electrical shock and X-rays. 1-1 Safety Precautions 1. Be sure that all of the built-in protective devices are replaced. Restore any missing protective shields. 2. When reinstalling the chassis and its assemblies, be sure to restore all protective devices, including: nonmetallic control knobs and compartment covers. 3. Make sure that there are no cabinet openings through which people--particularly children--might insert fingers and contact dangerous voltages. Such openings include the spacing between the picture tube and the cabinet mask, excessively wide cabinet ventilation slots, and improperly fitted back covers. If the measured resistance is less than 1.0 megohm or greater than 5.2 megohms, an abnormality exists that must be corrected before the unit is returned to the customer. 4. Leakage Current Hot Check (Figure 1-1): Warning: Do not use an isolation transformer during this test. Use a leakagecurrent tester or a metering system that complies with American National Standards Institute (ANIS C101.1, Leakage Current for Appliances), and Underwriters Laboratories (UL Publication UL1410, 59.7). 5. With the unit completely reassembled, plug the AC line cord directly into the power outlet. With the unit's AC switch first in the ON position and then OFF, measure the current between a known earth ground (metal water pipe, conduit, etc.) and all exposed metal parts, including: antennas, handle brackets, metal cabinets, screwheads and control shafts. The current measured should not exceed 0.5 milliamp. Reverse the powerplug prongs in the AC outlet and repeat the test. DEVICE UNDER TEST TEST ALL EXPOSED METAL SURFACES 2-WIRE CORD ALSO TEST WITH PLUG REVERSED (USING AC ADAPTER PLUG AS REQUIRED) LEAKAGE CURRENT TESTER (READING SHOULD NOT BE ABOVE 0.5mA) EARTH GROUND Fig. 1-1 AC Leakage Test 6. Antenna Cold Check: With the unit's AC plug disconnected from the AC source, connect an electrical jumper across the two AC prongs. Connect one lead of the ohmmeter to an AC prong. Connect the other lead to the coaxial connector. 7. X-ray Limits: The picture tube is especially designed to prohibit X-ray emissions. To ensure continued X-ray protection, replace the picture tube only with one that is the same type as the original. Carefully reinstall the picture tube shields and mounting hardware; these also provide X-ray protection. 8. High Voltage Limits: High voltage must be measured each time servicing is done on the B+, horizontal deflection or high voltage circuits. Correct operation of the X-ray protection circuits must be reconfirmed whenever they are serviced. (X-ray protection circuits also may be called "horizontal disable" or "hold-down".) Heed the high voltage limits. These include the X­ray Protection Specifications Label, and the Product Safety and X-ray Warning Note on the service data schematic. Samsung

File name 03_Reference Information.pdf

Reference Information 2. Reference Information 2-1 Tables of Abbreviations and Acronyms Table 2-1 Abbreviations A Ah Е dB dBm °C °F °K F G GHz g H Hz h ips kWh kg kHz k km km/h kV kVA kW I MHz Ampere Ampere-hour Angstrom Decibel Decibel Referenced to One Milliwatt Degree Celsius Degree Fahrenheit degree Kelvin Farad Gauss Gigahertz Gram Henry Hertz Hour Inches Per Second Kilowatt-hour Kilogram Kilohertz Kilohm Kilometer Kilometer Per Hour Kilovolt Kilovolt-ampere Kilowatt Liter Megahertz MV MW M m µA µF µH µm µs µW mA mg mH mI mm ms mV nF pF Ib rpm rps s V VA W Wh Megavolt Megawatt Megohm Meter Microampere Microfarad Microhenry Micrometer Microsecond Microwatt Milliampere Milligram Millihenry Milliliter Millimeter Millisecond Millivolt Nanofarad Ohm Picofarad Pound Revolutions Per Minute Revolutions Per Second Second (Time) Volt Volt-ampere Watt Watt-hour Samsung Electronics 2-1 Reference Information Table 2-2 Table of Acronyms ABL AC ACC AF AFC AFT AGC AM ANSI APC APC A/V AVC BAL BPF B-Y CATV CB CCD CCTV Ch CRT CW DC DVM EIA ESD ESD FBP FBT FF FM FS GND G-Y H HF HI-FI IC IC IF Automatic Brightness Limiter Alternating Current Automatic Chroma Control Audio Frequency Automatic Frequency Control Automatic Fine Tuning Automatic Gain Control Amplitude Modulation American National Standards Institute Automatic Phase Control Automatic Picture Control Audio-Video Automatic Volume Control Balance Bandpass Filter Blue-Y Community Antenna Television (Cable TV) Citizens Band Charge Coupled Device Closed Circuit Television Channel Cathode Ray Tube Continuous Wave Direct Current Digital Volt Meter Electronics Industries Association Electrostatic Discharge Electrostatically Sensitive Device Feedback Pulse Flyback Transformer Flip-Flop Frequency Modulation Fail Safe Ground Green-Y High High-Frequency High Fidelity Inductance-Capacitance Integrated Circuit Intermediate Frequency I/O L L LED LF MOSFET MTS NAB NEC NTSC OSD PCB PLL PWM QIF R RC RF R-Y SAP SAW SIF SMPS S/N SW TP TTL TV UHF UL UV VCD VCO VCXO VHF VIF VR VTR VTVM TR Input/output Left Low Light Emitting Diode Low Frequency Metal-Oxide-Semiconductor-Field-Effect-Tr Multi-channel Television Sound National Association of Broadcasters National Electric Code National Television Systems Committee On Screen Display Printed Circuit Board Phase-Locked Loop Pulse Width Modulation Quadrature Intermediate Frequency Right Resistor & Capacitor Radio Frequency Red-Y Second Audio Program Surface Acoustic Wave(Filter) Sound Intermediate Frequency Switching Mode Power Supply Signal/Noise Switch Test Point Transistor Transistor Logic Television Ultra High Frequency Underwriters Laboratories Ultraviolet Variable-Capacitance Diode Voltage Controlled Oscillator Voltage Controlled Crystal Oscillator Very High Frequency Video Intermediate Frequency Variable Resistor Video Tape Recorder Vacuum Tube Voltmeter Transistor 2-2 Samsung Electronics Reference Information 2-2 IC Line Up Table 2 - 3 IC Line - Up NO BOARD LOC

File name 04_Product Specification.pdf

Specifications 3. Specifications Television System Antena Input CS Consumption Power Requirements Frequency PAL/SECAM-B/G/D/K,L,I, NTSD-M 75ohms, Coaxial Cable 130W(Applied When 29" Flat) 220V Only Free Voltage 50/60Hz 15W x 2CH 10W x 2CH Output Sound 5W x 2CH 30W x 2CH 20W x 2CH Virtual Dolby Effect Trubo Sound Pseudo Stereo Woofer Sound Front(AV2) RCA Input S-VHS Head-Phone RCA99(AV2 Input/Out) Jacks BACK 2Scart Input/OUtput DVD Input(YPbPr) AV2 Monitro Audio Output S-VHS Woofer Output Specifications for Model Name (Ex. CS29A6??8X/HAC) Specifications for Model Name (Ex. CS29A6??8X/HAC) Function N P PF PT PW MT NT WT GW Samsung Electronics NICAM 2 TUNER PIP 2 TUNER PIP, NICAM, TTX 2 TUNER PIP, A2 STEREO, TTX 2 TUNER PIP, A2 STEREO 2 TUNER MULTI PIP, A2 STEREO, NICAM, TTX A2 STEREO, TTX 1 TUNER PIP, A2 STEREO, TTX 3-1 "NICAM" means that A2 STEREO + NICAM NOTE AV1: Scart I/O, RGB Input, RF Out AV2: Scart I/O, Monitor Out Not Present R815 29Inch 21Inch 29Inch Normal woofer 21Inch Flat woofer Option Option Option Option Option 2CH MEMO 3-2 Samsung Electronics

File name 05_Alignment & Adjustment.pdf

Alignment and Adjustments 4. Alignment and Adjustments 4-1 General Alignment Instructions 1. Usually, a color TV-VCR needs only slight touch-up adjustment upon installation. Check the basic characteristics such as height, horizontal and vertical sync and focus. 2. Observe the picture for good black and white details. There should be objectionable color shading; if color shading is present, demagnetize, perform purity and convergence adjustments described below. 3. Use the specified test equipment or its equivalent. 4. Correct impedance matching is essential. 8. To protect against shock hazard, use an isolation transformer. 5. Avoid overload. Excessive signal from a sweep generator might overload the front-end of the TV. When inserting signal markers, do not allow the marker generator to distort test results. 6. Connect the TV only to an AC power source with voltage and frequency as specified on the backcover nameplate. 7. Do not attempt to connect or disconnect any wires while the TV is turned on. Make sure that the power cord is disconnected before replacing any parts. 4-2 Automatic Degaussing A degaussing coil is mounted around the picture tube, so that external degaussing after moving the TV should be unnecessary. But the receiver must be properly degaussed upon installation. The degaussing coil operates for about 1 second after the power is switched ON. If the set is moved or turned in a different direction, the power should be OFF for at least 10 minutes. If the chassis or parts of the cabinet become magnetized, poor color purity will result. If this happens, use an external degaussing coil. Slowly move the degaussing coil around the faceplate of the picture tube and the sides and front of the receiver. Slowly withdraw the coil to a distance of about 6 feet before turning power OFF. If color shading persists, perform the following Color purity and Convergence adjustments. 4-3 High voltage Check CAUTION : There is no high voltage adjustment on this chassis. The B+ power supply should be +135 volts (with full color- bar input and normal picture level). 1. Connect a digital voltmeter to the second anode of the picture tube. 2. Turn on the TV. Set the Brightness and Contrast controls to minimum (zero beam current). 3. Adjust the Brightness and contrast controls to both extremes. Ensure that the high voltage does not exceed 32 KV under any conditions. Samsung Electronics 4-1 Alignment and Adjustments 4-4 Dynamic Focus Adjustment 1. A dynamic focus adjustment should be done after replacing the CRT PCB, FBT or CRT. 2. Input a crosshatch pattern. 3. Enter " STANDARD " in video mode. 4. Turn the Dynamic focus VR fully clockwise (maximum).( ) 5. Turn the Static focus VR fully counterclockwise (maximum).( ) 6. Slowly turn the static focus VR counterclockwise. Adjust until the vertical line in the middle of the screen has maximum clarity.( ) 7. Slowly turn the dynamic focus VR (clockwise) and adjust the 3rd horizontal line for maximum clari

File name 06_Troubleshooting.pdf

Plug in Power Cord Samsung Electronics ON Check LED lamp OFF Check MICOM IIC #5, #6 Normal Check and Replace the MICOM Normal Check and Replace IC903 Abnormal Normal Check IC901 MICOM Input Voltage Normal Abnormal Check the MICOM Power #59 With Remote Controller Replace the MICOM Abnormal Replace Q908 Normal Normal Check IC802, IC803 Replace IC802, IC803 Normal Check IC201S VDP H-OUT #50 Abnormal Replace IC201S Normal Check Q401 H-TR Replace Q401 Normal Check 135V Line Check PC801S, IC801S Normal Replace FBT Abnormal Abnormal Check R828 and D805 Abnormal Check IC801S and FP801S Normal Check and Replace R828 or D805 Abnormal Check IC804 Input Voltage Abnormal Normal Check and Replace IC804 Check D801 and D811 Abnormal Abnormal Replace D801 or D811 Check IC903 3.3V Regulator Input Voltage Normal Check Q908 5-1 No Power 5. Troubleshooting Abnormal Check Level Shifter Q909, Q910 Output(If 2N7000 Output has the DC Component over 0.7V, it is broken) Normal Abnormal Check MICOM IIC #2, #3 Abnormal Replace Q909, Q910 Normal Check IC902 EEPROM Replace EEPROM(IC902) Normal Check IC201S Note : When you check whether any component is normal, you must let the output pin be open in order not to be affected by the side of output. Troubleshooting 5-1 5-2 No Picture, but sound is in normal operation Turn the VR of FBT, higher screen voltage and Check the Deflection is in Normal Operation (If the deflection is in operation, flyback signal is appeared) Abnormal Abnormal Check IC201S #31 Normal Abnormal Check HIC202, HIC203, HIC204 Output Abnormal Check 8V Abnormal Normal Check IC803 Check IC301 Replace IC201S Abnormal Check DZ202 Normal Replace DZ202 Abnormal Normal Replace IC201S Check 200V, 16.5V Line Check Tuner CVBS Output Check IC201S #63 or #59 Normal Troubleshooting 5-2 No Picture Normal Normal Check CRT PCB RK, BK, GK Check Heater Voltage Abnormal Normal Check CRT and FBT Check CRT and FBT Samsung Electronics Troubleshooting 5-3 No Sound No Sound, but Picture is in normal operation Normal Check the CN602 Connection and Signal Abnormal Check the Speaker Wire Connection Normal Check 14V Line Abnormal Check IC602 #7 (If the pin is in low state, Sound is mute) Normal Abnormal Check FA803S Check D816, Q906 Check IC601 #24, #25 Normal Replace IC602 Check IC601 Input Voltages (5V,8V) Normal Check the coils around IC601 Check IC601 Input Signal Normal Replace IC601 Check the Tuner Abnormal Abnormal Abnormal Samsung Electronics 5-3 MEMO 5-4 Samsung Electronics

File name 07_Exploded View & Part List.pdf

Exploded View & Parts List 6. Exploded View & Parts List 6-1 CW28C73WS8XXEG No 1* 1-1 1-2 1-3 1-4 1-5 1-6 1-7 1-8 1-9 1-10 1-11 1-12 1-13 1-14 1-15 2 2-1 2-2 2-3 3 3-1 3-2 Code No AA64-02420F HA64-27016A AA64-00189B AA64-00190A AA64-70117B AA61-30001A AA64-02509B AA61-60003T AA64-02482A AA64-00191A 6002-000515 6002-000515 AA95-01525A HA96-00091B 6002-000515 AA61-40010A HA94-500023 AA65-30007A AA60-10050Q 3704-001105 HA64-02431B 6002-000515 AA96-20122B Description;Specification CABINET-FRONT;28C7,HIPS,HB,SV-012P-II,GR DOOR-CONTROL;28C7,HIPS,HB,SV-012P-II INLAY-CONTROL;28C7,PS,T0.3,-,-,BLK,S51A WINDOW-REMOCON;-,28C7,-,PC,-,VIOLET,BADGE-BRAND;-,AL,-,-,L65,R2000,SILVER,SS LATCH-DOOR;-,-,-,-,-,-,KIFUCO LA701 KNOB POWER;28C7,HIPS,HB,SV-012P-II,GRY SPRING-CS;-,SUS304,-,-,OD7,N5,OD7,-,-,-, KNOB CONTROL;28C7,HIPS,HB,GRY INDICATOR-LED;28C7,ACRYL,-,CLR,-,-,SCREW-TAPPING;RH,+,2,M4,L15,ZPC(WHT),SWR SCREW-TAPPING;RH,+,2,M4,L15,ZPC(WHT),SWR ASSY PCB CONTROL;,KS3A,28C7,50HZ ASSY-SPEAKER;16##,10W,3001-001005,AA39-2 SCREW-TAPPING;RH,+,2,M4,L15,ZPC(WHT),SWR BOSS-WING;-,HIPS,-,-,-,NTR,HB ASSY-CRT;A66EHJ13X38,+450MG,28,ITC,NORM CLAMP-D,COIL;-,NYLON-66,V0,-,NTR,WIDE SCREW-ASSY;-,SWRCH18A,M5,L26.5,HH,+,WC,SOCKET-CRT;11P,20PI,26.5PI,NI,CABINET BACK;CABINET BACK;28C7,HIPS,HB,G SCREW-TAPPING;RH,+,2,M4,L15,ZPC(WHT),SWR ASSY-POWER,CORD;-,CP2/NO(4.0),H/C500MM,K Q'ty 1 1 1 1 1 1 1 1 1 1 1 1 1 1 4 1 1 4 4 1 1 7 1 Remark CF+KC CF+IND CF+SPK CF+CRT V999S CB+CF Samsung Electronics 6-1 Exploded View & Parts List 6-2 CW28C93WS8XXEG No 1 1* 1-1 1-2 1-3 1-4 1-5 1-6 1-8 1-9 1-10 1-11 1-12 1-13 1-14 1-15 2 2-1 2-2 2-3 3 3-1 3-2 Code No HA91-00877A AA64-02413A AA64-02587A AA64-01564C AA64-70117B AA61-30001A AA64-02506A AA61-60003T AA64-02479A 6002-000515 AA64-02463A 6002-000515 AA95-01529A 6003-001023 3001-001005 6002-000515 HA94-500023 AA65-30007A AA60-10050Q 3704-001105 HA64-02423A 6002-000515 AA96-20122A Description;Specification ASSYCABINETFRONT;28C9,SV-011P-II CABINET-FRONT;28C9,HIPS,HB,SV-012P-II,GR DOOR CONTROL;28C9,HIPS,SV-012P-II,SILVER INLAY-CONTROL;28C9,PS SHEET,T0.3,-,-,-,K BADGE-BRAND;-,AL,-,-,L65,R2000,SILVER,SS LATCH-DOOR;-,-,-,-,-,-,KIFUCO LA701 KNOB POWER;28C9,HIPS,HB,SV-012P-II,GRY SPRING-CS;-,SUS304,-,-,OD7,N5,OD7,-,-,-, KNOB CONTROL;28C9,HIPS,HB,GRY SCREW-TAPPING;RH,+,2,M4,L15,ZPC(WHT),SWR WINDOW REMOCON-LED;28C9,V0,VIOLET SCREW-TAPPING;RH,+,2,M4,L15,ZPC(WHT),SWR ASSY PCB CONTROL;,KS3A,XXW7-C9,50HZ SCREW-TAPTITE;RWH,+,B,M3,L10,ZPC(YEL),SW SPEAKER;10W,8OHM,91DB,140HZ SCREW-TAPPING;RH,+,2,M4,L15,ZPC(WHT),SWR ASSY-CRT;A66EHJ13X38,+450MG,28,ITC,NORM CLAMP-D,COIL;-,NYLON-66,V0,-,NTR,WIDE SCREW-ASSY;-,SWRCH18A,M5,L26.5,HH,+,WC,SOCKET-CRT;11P,20PI,26.5PI,NI,CABINETBACK;28C9,HIPS,HB,GRY SCREW-TAPPING;RH,+,2,M4,L15,ZPC(WHT),SWR ASSY-POWER,CORD;-,CP2/NO(4.0),H/C250,KKJ Q'ty 1 1 1 1 1 1 1 1 1 1 1 1 1 4 2 8 1 4 4 1 1 7 1 Remark * KC+CF WIN+CF CONTRO SPK+CF CRT+CF V999S CB+CF 6-2 Samsung Electronics Exploded View & Parts List 6-3 CW29K86VS8XXEC No 1 1*

File name 08_Electrical Part List.pdf

Electrical Parts List 7. Electrical Parts List 7-1 CW25C33WS8XXEG Level Loc. No. Code No. Description ; Specification Remark Level Loc. No. Code No. Description ; Specification Remark ASSY PCB MAIN(OPT) 1 2 2 2 2 2 3 3 3 3 ! 2 2 2 2 3 3 3 3 2 2 2 2 2 2 2 2 2 2 2 2 2 2 3 3 3 3 2 3 3 3 3 3 3 3 3 2 2 3 3 3 3 2 2 2 3 3 3 3 3 3 2 2 ! 2 2 * V999S CN501A CN502A TOP IC501 AA94-05578B ASSY PCB MAIN(OPT);CW25C3W,KS3A/H,SEB,AK 3704-001105 SOCKET-CRT;11P,20PI,26.5PI,NI,AA39-00241A LEAD CONNECTOR ASSY;,6P,YBNH250-06,S,500 AA39-20053B LEAD CONNECTOR-ASSY;,5P,YBNH025-05,S,500 AA39-20010B LEAD CONNECTOR-ASSY;,1P,YFH800-01,S,500, HA96-00276B ASSY H/S;-,VIDEO AMP,AA62-00052A,STV510 1201-001687 IC-VIDEO AMP;STV5109,ZIP,15P,-,SINGLE,50 AA62-00052A HEAT SINK-PS;-,-,-,SILVER,HOLE 18.5mm, 2 6003-000334 SCREW-TAPTITE;RH,+,2S,M3,L6,ZPC(YEL),SWR 0205-000129 GREASE-SILICON;SC102,JAPAN AA26-00046B TRANS SWITCHING;CODE-NO,CW6844N8X/XEF,-, 1204-001634 IC-VIDEO PROCESS;VDP3120B-C3,DIP,64P,-,P AA40-00079A TUNER;TCPW3001PD16A(S),PAL,181CH,38. HA96-50398B ASSY-H/S;ASSY-H/S;AA62-30182E,TDA7266S, 1201-001308 IC-POWER AMP;7266,ZIP,15P,-,DUAL,26dB,PL AA62-30181F HEAT-SINK,ES;-,AL6063 EXTR.,2,WHT,50MM,6003-000333 SCREW-TAPTITE;RH,+,2S,M3,L10,ZPC(YEL),SW 0205-000129 GREASE-SILICON;SC102,JAPAN 1204-001817 IC-SOUND PROCESSOR;MSP3400D-C5-G4-LH,DIP AA26-30005U TRANS-FLYBACK;-,FUH-29A003,29',155V 1404-001156 THERMISTOR-PTC;9OHM,+30%/-20%,220VRMS,27 2401-001137 C-AL;330uF,20%,400V,GP,BK,30x45mm,1 2306-000178 C-FILM,MPPF;3.9nF,5%,1.6KV,BK,31x15x8.5, 2306-000253 C-FILM,MPPF;7.2nF,5%,1.6KV,TP,28.5x18.5x 2306-000188 C-FILM,MPPF;330nF,5%,400V,TP,26x19.5x11, AA27-30001F COIL-LINEARLITY;-,22uH,DR1011,PI0.45,25. AA27-00103A COIL CHOKE;600UH,-,600UH,+-10%,600UH,0.5 AA27-00057A COIL HORIZ. WIDTH;-,10mH,YL-9N 15x27.5 C 2306-000204 C-FILM,MPPF;430nF,5%,400V,TP,26x20.5x12. 2306-000318 C-FILM,MPPF;220nF,20%,250V,TP,-,22.5mm AA29-00015A FILTER LINE NOISE;WS32W8,28-20MH 1.5A,+HA96-50406A ASSY-H/S;ASSY-H/S;AA62-30180K,LA7845,1204-000517 IC-VERTICAL DEF.;LA7845,SIP,7P,-,PLASTIC AA62-30180K HEAT-SINK,ES;-,A6063 EXTR,-,WHT,50/13,-, 6003-000333 SCREW-TAPTITE;RH,+,2S,M3,L10,ZPC(YEL),SW 0205-000129 GREASE-SILICON;SC102,JAPAN HA96-00274A ASSY-H/S;-,COMPLEX,AA62-00053A,FMLG12S 6003-000334 SCREW-TAPTITE;RH,+,2S,M3,L6,ZPC(YEL),SWR AA62-00053A HEAT SINK-PS;-,-,-,SILVER,HOLE 22mm,ALL, 0402-001230 DIODE-RECTIFIER;FMG-G2CS,1000V,3A,TO-220 0402-000233 DIODE-RECTIFIER;FML-G12S,200V,5A,-,0402-000233 DIODE-RECTIFIER;FML-G12S,200V,5A,-,0402-000233 DIODE-RECTIFIER;FML-G12S,200V,5A,-,1203-001006 IC-VOLTAGE REGULATOR;78R05,TO-220F,4P,-, 0205-000129 GREASE-SILICON;SC102,JAPAN 1203-001697 IC-VOLTAGE REGULATOR;78R08,TO-220,4P,-,P HA96-00243C ASSY-H/S;-,REGULATOR,AA62-00045A,KA7806 1203-000284 IC-POSI.FIXED REG.;7806,TO-220,3P,-,PLAS 6003-000333 SCREW-TAPTITE;RH,+,2S,M3,L10,ZPC(YEL),SW AA62-00065A HEAT SINK-PS;DP,-,-,-,AA62-00045A,-,-,-, 0205-000129 GREASE-SILICON;SC102,JAPAN 1103-001171 IC-EEPROM;L51DC,16KBit,DIP,8P,300MIL,10m AA0

File name 09_Block Diagram.pdf

Block Diagrams 8. Block Diagrams 8-1 Power Diagram Samsung Electronics 8-1 Block Diagrams 8-2 Block Diagram 8-2 Samsung Electronics

File name 10_Wiring Diagram.pdf

Wiring Diagram 9. Wiring Diagram CONTROL PCB L+ CNY02 KEY2 KEY1 GND KEY3 CNY01 TIME STD GND 5V IR R+ S-VHS IN-OUT CN703 RGND LL+ VO SC-1 GND SY-I CN704 LR+ RTO SPEAKER SIDE AV PCB CN702 GND SC-O GND SY-O FROM MAIN SOUND AMP CN701 GD VI GD LO RO LI RI AV2 VIDEO IN-OUT CN901 KEY2 KEY1 GND KEY3 CN902 TIME STD GND 5V IR CN602 R+ R- CN302 VERT V2 V1 NC 16.5V GND CN501 B OUT G OUT R OUT SENSE 8V GND F/B TILT GND CN702 VO GD V1 GD LO RO GND MAIN PCB LL+ 600V VERT V2 V1 NC 16.5V GND CN502 -16V SVM CNH01 LI ABL +16V GND HEAT NC 200V RI DOUBLE FOCUS PCB 600V SC-I CN704 16.5VAC GND DOUBLE 16.5VAC GND DOUBLE GND SY-I GND SC-O GND SY-O B OUT CN501A G OUT R OUT SENSE 8V GND F/B TILT GND SVM -16V ABL +16V GND HEAT NC 200V CRT PCB CN502A Samsung Electronics 9-1 MEMO 9-2 Samsung Electronics

File name 11_Schematic Diagram.pdf

Schematic Diagrams 10. Schematic Diagrams 10-1 MAIN 1 TP07 TP01 TP10 TP08 TP02 TP09 TP03 TP09 TP01 TP06 TP10 TP04 TP08 TP03 TP05 TP05 TP02 TP07 TP04 TP06 Samsung Electronics 10-1 Schematic Diagrams 10-2 MAIN 2 TP11 TP12 TP13 TP12 TP13 TP14 TP11 TP25 TP15 TP14 TP25 TP15 10-2 Samsung Electronics Schematic Diagrams 10-3 MAIN3 TP22 TP16 TP23 TP23 TP17 TP22 TP17 TP16 TP18 TP24 TP18 TP19 TP21 TP20 TP19 TP24 TP20 TP21 Samsung Electronics 10-3 Schematic Diagrams 10-4 MAIN 4 TP31 TP26 TP32 TP27 TP26 TP28 TP27 TP29 TP32 TP31 TP30 TP28 TP29 TP30 10-4 Samsung Electronics Schematic Diagrams 10-5 PIP MODULE, SWITCH MODULE PIP MODULE SWITCH MODULE Samsung Electronics 10-5 Schematic Diagrams 10-6 CRT wtih in V/M wtih out V/M TP33 TP34 TP35 TP33 TP34 TP35 10-6 Samsung Electronics Schematic Diagrams 10-7 SIDE AV, DOUBLE FOCUS SIDE AV DOUBLE FOCUS Samsung Electronics 10-7 Schematic Diagrams 10-8 WOOFER 10-8 Samsung Electronics