JVC GR-DV500U free download

File name 86734-P.pdf

5.1 EXPLODED VIEW SECTION 5 PARTS LIST SAFETY PRECAUTION Parts identified by the symbol are critical for safety. Replace only with specified part numbers. BEWARE OF BOGUS PARTS Parts that do not meet specifications may cause trouble in regard to safety and performance. We recommend that genuine JVC parts be used. 5.1.1 PACKING AND ACCESSORY ASSEMBLY The instruction manual to be provided with this product will differ according to the destination. 075 008 094 007 085 051 050 048 047 046 043 042 086 024 041 079 080 073 083 092 082 093 087 091 078 077 081 076 074 014 FINAL ASSY 072 071 009 003 006 LABEL (SERIAL, ACC.) 022 004 005 002 LABEL (SERIAL) 5-1 5.1.2 FINAL ASSEMBLY, REAR ASSEMBLY(G) AND SHOE ASSEMBLY(G) FINAL ASS'Y REAR ASS'Y(G) SHOE ASS'Y(G) OP FRAME ASS'Y TABLE OF SETTING TORQUE FOR SCREW DRIVER PART.NO 112 121 126 127 128 132 133 133 123 124 COVER(SHOE) ASS'Y 104 OP FRAME ASS'Y p1 p2 132 SETTING TORQUE 0.07 ±0.007 N·m 0.10 ±0.010 N·m 0.08 ±0.008 N·m f 146 g u NOTES 1. BEND FPC , AND PASS THE CORNER HOLE OF THE SHEET METAL . 2. BE CAREFUL NOT TO CUT FPC BY THE SHEET METAL EDGE . 3. NOTE IT EXTERNALS WHERE THE DENT IS NOT IN FPC WITH THE WOUND . 4. DO NOT TOUCH BY THE FINGER TERMINAL AREA OF FPC . 147 NOTES 291 SHOE ASS'Y BKT(H.S) 292 119 p1 n r OTHER SCREW SHOE ASS'Y(G) LYH20612 294 BKT (SHOE MIC) PROCESS THIS PART OF DRUM MOTOR FPC TO THE SHIELDING CASE . FRONT ASS'Y(G) (Refer to the Exploded view for this part.) 125 q 126 g a2 120 a1 109 m g 293 131 p2 FIG.1 DRUM MOTOR FPC PROCESSING CHART LOWER CASE ASS'Y <02> JACK BOARD ASS'Y b 113 102 n f s3 s1 r LOWER CASE ASS'Y (Refer to the Exploded view for this part.) 152 SHIELD COVER(PR) 108 151 S TERMINAL h1 h2 j1 j2 j3 j6 g c k1 s4 j4 z3 s2 z2 k3 p1 p2 k2 135 p1 p2 SUPPRESS FROM BOTH SIDES OF UPPER AND LOWER FIRMLY, AND TIGHTEN FROM RIGHT SCREW. k2 112 110 113 u m a2 b r c a1 q j2 h1 h2 j5 j4 110 105 s2 s3 'h1 'h2 111 j1 116 j3 'h1 j6 'h2 s4 t s1 j5 115 FIG.2 STOPPER(JACK) INSTALLATION CHART 113 d z2 121 z1 114 (Refer to the Exploded view for this part.) MECHANISM ASS'Y z3 103 BASE y 145 k3 122 UPPER ASS'Y(G) 148 REAR ASS'Y(G) 134 BKT(MECHA) ASS'Y d <04> PRE/MDA BOARD ASS'Y 117 REAR ASS'Y(G) LYH20611 PASTE ACCORDING TO THE CORNER OF THIS COIL AND APPLY IT. 283 282 145 DO NOT PUT EXTERNAL FORCE ON THE FPC ROOT WHEN BENDING IT. REAR UNIT 281 SOLDERING t IT MATCHES IT TO THE END FACE OF THE PWB. IT MATCHES IT TO THE END FACE OF C6202. C6202 e 130 y z1 e 128 127 129 <01> MAIN BOARD ASS'Y 285 287 PUT IT SO THAT THE SHEET SHOULD NOT FLOAT. ESPECIALLY, NOTE THE PWB END FACE SIDE. FIG-2. SHIELD AFFIXATION POSITION 284 285 <03> REG BOARD ASS'Y DO NOT PUT EXTERNAL FORCE ON THE FPC ROOT. FIG-1. SPACER AFFIXATION POSITION OP FRAME ASS'Y J2G TYPE 118 J7C TYPE BKT(OP-J7) ASS'Y 106 SPACER DOSE NOT GO UP PART OF BKT. STICKING AS SHOWN IN FIGURE. (MACHING TO FRONT EDGE.) 149 118 w SPACER(A) 150 FINAL ASS'Y LYH20

File name 86734.pdf

SERVICE MANUAL DIGITAL VIDEO CAMERA GR-DV500US, GR-DV800US, GR-DV801US, GR-DV900US Regarding service information other than these sections, refer to the service manual No. 86736 (GR-DV4000US). Also, be sure to note important safety precautions provided in the service manual. SPECIFICATIONS (The specifications shown pertain specifically to the model GR-DV500U, GR-DV800U and GR-DV900U.) Camcorder For General Power supply : DC 11 V (Using AC Adapter) DC 7.2 V (Using battery pack) Approx. 3.7 W Approx. 4.8 W 74.5 mm x 91 mm x 185 mm (2-15/16" x 3-5/8" x 7-5/16") (with the LCD monitor closed and the viewfinder pushed back in) Approx. 610 g (1.4 lbs) (GR-DV900/800) Approx. 575 g (1.3 lbs) (GR-DV500) (without cassette, memory card and battery) Approx. 750 g (1.7 lbs) (GR-DV900/800) Approx. 715 g (1.6 lbs) (GR-DV500) (incl. cassette, memory card and battery) 0°C to 40°C (32°F to 104°F) 35% to 80% ­20°C to 50°C (­4°F to 122°F) 1/4" CCD F 1.2, f = 3.8 mm to 38 mm, 10:1 power zoom lens (GR-DV900) F 1.8, f = 3.8 mm to 38 mm, 10:1 power zoom lens (GR-DV800/500) ш52 mm 3.5" diagonally measured, LCD panel/TFT active matrix system (GR-DV900/800) 2.5" diagonally measured, LCD panel/TFT active matrix system (GR-DV500) Electronic viewfinder with 0.24" color LCD Monaural For Digital Still Camera Storage media Compression system File size Still image : : SD Memory Card/MultiMediaCard Still image : JPEG (compatible) Moving image : MPEG4 (compatible) Power consumption LCD monitor off, viewfinder on : LCD monitor on, viewfinder off : Dimensions (W x H x D) : Weight : : 4 modes (1600 x 1200 pixels/1280 x 960 pixels/1024 x 768 pixels/ 640 x 480 pixels) Moving image : 1 mode (160 x 120 pixels) Picture quality : 2 modes (FINE/STANDARD) Approximate number of storable images : pg. 39 For Connectors S S-Video input S-Video output AV Video input Video output Audio input Audio output EDIT Headphone output DV Input/output USB : : Operating temperature Operating humidity Storage temperature Pickup Lens Filter diameter LCD monitor : : : : : : : Y: 0.8 V to 1.2 V (p-p), 75 analog , C: 0.2 V to 0.4 V (p-p), 75 analog , Y: 1.0 V (p-p), 75 analog , C: 0.29 V (p-p), 75 analog , Y: 0.8 V to 1.2 V (p-p), 75 analog , Y: 1.0 V (p-p), 75 analog , 300 mV (rms), 50 k analog, stereo , 300 mV (rms), 1 k analog, stereo , ш3.5 mm, 2-pole Stereo 4-pin, IEEE 1394 compliant 5-pin : : : : : : : : Viewfinder Speaker For Digital Video Camera Format Signal format Recording/Playback format : : : : : Cassette Ta pe speed Maximum recording time (using 80 min. cassette) : : : DV format (SD mode) NTSC standard Video : Digital component recording Audio : PCM digital recording, 32 kHz 4-channel (12-bit), 48 kHz 2-channel (16-bit) Mini DV cassette SP: 18.8 mm/s LP: 12.5 mm/s SP: 80 min. LP: 120 min. AC Adapter For General Power requirement U.S.A. and Canada Other countries Output : : : AC 120 Vd, 60 Hz AC 110 V to 240 Vd, 50 Hz/60 Hz DC 11 V G, 1 A Specifications shown are for SP mode u

File name 86734B.pdf

Additional edition SERVICE MANUAL DIGITAL VIDEO CAMERA 3 2004 86734B GR-DV500US, GR-DV800US, GR-DV801US, GR-DV900US Regarding service information other than these sections, refer to the service manual No. 86736 (GR-DV4000US). Also, be sure to note important safety precautions provided in the service manual. NOTE This service manual describes differences related to the change of CCD. This service manual contains differences from the issued service manual. There are two types of CCD used for this model: P type and S type. Prior to repair operation, be sure to see the CCD. Previous (P TYPE) New (S TYPE) For distinction, see the following. 1. Dictinction based on a RATING LABEL attached to the set and a CARTON LABEL attached to the PACKING CASE. 2. Distinction based on parts numbers of MAIN BOARD ASSEMBLY/REG BOARD ASSEMBLY/CCD BOARD ASSEMBLY. NO. 1 ITEM RATING LABEL CARTON LABEL Previous (P TYPE) "A" is not attached to the end of SERIAL No.Example :[00000001]. "A" is not added to the end of the number beside the model name. Example: [1] YB10434A SERIES YB10434B SERIES YB20945B SERIES YB10423 SERIES New (S TYPE) "A" is attached to the end of SERIAL No.Example: [00000001A] "A" is added to the end of the number beside the model name. Example: [1A] YB10434M SERIES YB10434N SERIES YB20945C SERIES YB10422 SERIES 2 MAIN BOARD ASSEMBLY REG BOARD ASSEMBLY CCD BOARD ASSEMBLY GR-DV500US M3D4S3 GR-DV800US M3D4L3 GR-DV801US M3D4L3 GR-DV900US M3D4L7 COPYRIGHT © 2004 VICTOR COMPANY OF JAPAN, LIMITED No.86734B 2004/3 The following tables indicate differences of parts numbers between models Previous(P TYPE) and New(S TYPE). FINAL ASSEMBLY REF NO. 143 243 264 Previous Part No. (P TYPE) J7C-117A J2G-301A LYH30375-009A LYH30375-009A New Part No. (S TYPE) J7C-317A J2G-101A LYH30375-008A LYH30375-008A Part Name OP BLOCK ASSY CCD BASE ASSY CCD BASE ASSY MAIN BOARD ASSEMBLY<01> Previous Part No. REF NO. (P TYPE) PW1 YB10434A-01 YB10434B YB10434B-01 C5010 NBP21DM-475X C2021 NBP21DM-475X R5001 R5004 NRSA6AJ-0R0W R5005 NRSA6AJ-0R0W R5020 NRSA6AJ-0R0W R5021 NRSA6AJ-104W R5022 R5023 NRSA6AJ-0R0W L5007 L5008 NQR0129-002X REG BOARD ASSEMBLY <03> Previous Part No. REF NO. (P TYPE) PW1 YB20945B-02 YB20945B-03 C6121 NCBA1CK-223W C6221 NCBA1CK-102W R6240 NRSA6AD-473W R6241 NRSA6AD-103W R6242 NRSA6AD-683W CCD BOARD ASSEMBLY <10> Previous Part No. REF NO. (P TYPE) PW1 YB10423A-01 YB10423-01-01 Q5201 2SC3931/CD/-X Q5202 Q5203 R5201 NRSA63J-222X R5202 NRSA63J-0R0X R5203 NRSA63J-105X R5204 NRSA63J-105X R5205 NRSA63J-102X R5206 NRSA63J-0R0X R5207 NRSA63J-0R0X C5201 NCB31EK-104X C5202 NBP41DM-106X C5203 NBE21AM-106X C5204 NCB31EK-104X C5205 NCB31EK-104X C5206 NCB31HK-102X C5207 NCB31EK-103X C5211 L5201 NQL315K-100X Note: Mark is same as left. Mark - is not used. 1-2 (No.86734B) New Part No. (S TYPE) YB10434M YB10434N YB10434N NBZ0003-475X NBZ0003-475X NRSA6AJ-104W NRSA6AJ-100W NRSA6AJ-100W NRSA6AJ-100W NRSA6AJ-0R0W NQR0129-002X - Part Name MAIN BOA

File name 86734SCH.pdf

Preliminary SECTION 4 CHARTS AND DIAGRAMS NOTES OF SCHEMATIC DIAGRAM Safety precautions The Components identified by the symbol are critical for safety. For continued safety, replace safety critical components only with manufacturer's recommended parts. 1. Units of components on the schematic diagram Unless otherwise specified. 1) All resistance values are in ohm. 1/6 W, 1/8 W (refer to parts list). Chip resistors are 1/16 W. K: KШ (1000Ш), M: MШ (1000KШ) 2) All capacitance values are in µF, (P: PF). 3) All inductance values are in µH, (m: mH). 4) All diodes are 1SS133, MA165 or 1N4148M (refer to parts list). Note: The Parts Number, value and rated voltage etc. in the Schematic Diagram are for references only. When replacing the parts, refer to the Parts List. 2. Indications of control voltage AUX : Active at high. AUX or AUX(L) : Active at low. Playback and recording signal path Recording signal path (including E-E signal path) Capstan servo path CIRCUIT BOARD NOTES 1. Foil and Component sides 1) Foil side (B side) : Parts on the foil side seen from foil face (pattern face) are indicated. 2) Component side (A side) : Parts on the component side seen from component face (parts face) indicated. 4. Voltage measurement 1) Regulator (DC/DC CONV) circuits REC : Colour bar signal. PB : Alignment tape (Colour bar). -- : Unmeasurable or unnecessary to measure. 4) Indication on schematic diagram Voltage Indications for REC and PB mode on the schematic diagram are as shown below. 2. Parts location guides Parts location are indicated by guide scale on the circuit board. 1 REC mode 2.5 (5.0) PB mode 1.8 2 3 REF No. IC101 B : Foil side (A : Component side) C : Chip component D : Discrete component) LOCATION IC B C Category : IC 6A Horizontal "A" zone Vertical "6" zone PB and REC modes (Voltage of PB and REC modes are the same) Note: If the voltages are not indicated on the schematic diagram, refer to the voltage charts. 5. Signal path Symbols The arrows indicate the signal path as follows. NOTE : The arrow is DVC unique object. Playback signal path Note: For general information in service manual, please refer to the Service Manual of GENERAL INFORMATION Edition 4 No. 82054D (January 1994). 3. Interpreting Connector indications 1 2 3 1 2 3 Removable connector (Example) Drum servo path Wire soldered directly on board R-Y Y Playback R-Y signal path Recording Y signal path 1 2 3 1 2 3 4 Non-removable Board connector 6. Indication of the parts for adjustments The parts for the adjustments are surrounded with the circle as shown below. Board to Board Connected pattern on board The arrows indicate signal path 7. Indication of the parts not mounted on the circuit board Note: For the destination of each signal and further line connections that are cut off from the diagram, refer to "BOARD INTERCONNECTIONS" "OPEN" is indicated by the parts not mounted on the circuit board. R216 OPEN 4-1 4-2 S40889-01 1 T_RL[+] 4 3 2 3 4 5 GND T_RL[-] 2 1

File name 86736-P.pdf

SECTION 5 PARTS LIST 5.1 EXPLODED VIEW SAFETY PRECAUTION Parts identified by the symbol are critical for safety. Replace only with specified part numbers. BEWARE OF BOGUS PARTS Parts that do not meet specifications may cause trouble in regard to safety and performance. We recommend that genuine JVC parts be used. 5.1.1 PACKING AND ACCESSORY ASSEMBLY The instruction manual to be provided with this product will differ according to the destination. 085 008 074 007 051 050 048 047 046 043 042 078 081 086 077 093 087 091 024 041 080 082 014 FINAL ASSY 072 073 083 079 092 071 009 003 006 LABEL (SERIAL, ACC.) 022 004 005 002 LABEL (SERIAL) 5-1 5.1.2 FINAL ASSEMBLY, REAR ASSEMBLY(G) AND SHOE ASSEMBLY(G) FINAL ASS'Y REAR ASS'Y(G) SHOE ASS'Y(G) OP FRAME ASS'Y TABLE OF SETTING TORQUE FOR SCREW DRIVER PART.NO 112 121 126 127 128 132 133 133 123 124 COVER(SHOE) ASS'Y 104 OP FRAME ASS'Y p1 p2 132 SETTING TORQUE 0.07 ±0.007 N·m 0.10 ±0.010 N·m 0.08 ±0.008 N·m f 146 g u NOTES 1. BEND FPC , AND PASS THE CORNER HOLE OF THE SHEET METAL . 2. BE CAREFUL NOT TO CUT FPC BY THE SHEET METAL EDGE . 3. NOTE IT EXTERNALS WHERE THE DENT IS NOT IN FPC WITH THE WOUND . 4. DO NOT TOUCH BY THE FINGER TERMINAL AREA OF FPC . 147 NOTES 291 SHOE ASS'Y BKT(H.S) 292 119 p1 n r OTHER SCREW SHOE ASS'Y(G) LYH20612 294 BKT (SHOE MIC) PROCESS THIS PART OF DRUM MOTOR FPC TO THE SHIELDING CASE . FRONT ASS'Y(G) (Refer to the Exploded view for this part.) 125 q 126 g a2 120 a1 109 m g 293 131 p2 FIG.1 DRUM MOTOR FPC PROCESSING CHART LOWER CASE ASS'Y <02> JACK BOARD ASS'Y b 113 102 n f s3 s1 r LOWER CASE ASS'Y (Refer to the Exploded view for this part.) 152 SHIELD COVER(PR) 108 151 S TERMINAL h1 h2 j1 j2 j3 j6 g c k1 s4 j4 z3 s2 z2 k3 p1 p2 k2 135 p1 p2 SUPPRESS FROM BOTH SIDES OF UPPER AND LOWER FIRMLY, AND TIGHTEN FROM RIGHT SCREW. k2 112 110 113 u m a2 b r c a1 q j2 h1 h2 j5 j4 110 105 s2 s3 'h1 'h2 111 j1 116 j3 'h1 j6 'h2 s4 t s1 j5 115 FIG.2 STOPPER(JACK) INSTALLATION CHART 113 d z2 121 z1 114 (Refer to the Exploded view for this part.) MECHANISM ASS'Y z3 103 BASE y 145 k3 122 UPPER ASS'Y(G) 148 REAR ASS'Y(G) 134 BKT(MECHA) ASS'Y d <04> PRE/MDA BOARD ASS'Y 117 REAR ASS'Y(G) LYH20611 PASTE ACCORDING TO THE CORNER OF THIS COIL AND APPLY IT. 283 282 145 DO NOT PUT EXTERNAL FORCE ON THE FPC ROOT WHEN BENDING IT. REAR UNIT 281 SOLDERING t IT MATCHES IT TO THE END FACE OF THE PWB. IT MATCHES IT TO THE END FACE OF C6202. C6202 e 130 y z1 e 128 127 129 <01> MAIN BOARD ASS'Y 285 287 PUT IT SO THAT THE SHEET SHOULD NOT FLOAT. ESPECIALLY, NOTE THE PWB END FACE SIDE. FIG-2. SHIELD AFFIXATION POSITION 284 285 <03> REG BOARD ASS'Y DO NOT PUT EXTERNAL FORCE ON THE FPC ROOT. FIG-1. SPACER AFFIXATION POSITION OP FRAME ASS'Y J2G TYPE 118 J7C TYPE BKT(OP-J7) ASS'Y 106 SPACER DOSE NOT GO UP PART OF BKT. STICKING AS SHOWN IN FIGURE. (MACHING TO FRONT EDGE.) 149 118 w SPACER(A) 150 FINAL ASS'Y LYH20608 THE INT

File name 86736-S.pdf

SECTION 4 CHARTS AND DIAGRAMS NOTES OF SCHEMATIC DIAGRAM Safety precautions The Components identified by the symbol are critical for safety. For continued safety, replace safety critical components only with manufacturer's recommended parts. 1. Units of components on the schematic diagram Unless otherwise specified. 1) All resistance values are in ohm. 1/6 W, 1/8 W (refer to parts list). Chip resistors are 1/16 W. K: KШ (1000Ш), M: MШ (1000KШ) 2) All capacitance values are in µF, (P: PF). 3) All inductance values are in µH, (m: mH). 4) All diodes are 1SS133, MA165 or 1N4148M (refer to parts list). Note: The Parts Number, value and rated voltage etc. in the Schematic Diagram are for references only. When replacing the parts, refer to the Parts List. 2. Indications of control voltage AUX : Active at high. AUX or AUX(L) : Active at low. Playback and recording signal path Recording signal path (including E-E signal path) Capstan servo path CIRCUIT BOARD NOTES 1. Foil and Component sides 1) Foil side (B side) : Parts on the foil side seen from foil face (pattern face) are indicated. 2) Component side (A side) : Parts on the component side seen from component face (parts face) indicated. 4. Voltage measurement 1) Regulator (DC/DC CONV) circuits REC : Colour bar signal. PB : Alignment tape (Colour bar). -- : Unmeasurable or unnecessary to measure. 4) Indication on schematic diagram Voltage Indications for REC and PB mode on the schematic diagram are as shown below. 2. Parts location guides Parts location are indicated by guide scale on the circuit board. 1 REC mode 2.5 (5.0) PB mode 1.8 2 3 REF No. IC101 B : Foil side (A : Component side) C : Chip component D : Discrete component) LOCATION IC B C Category : IC 6A Horizontal "A" zone Vertical "6" zone PB and REC modes (Voltage of PB and REC modes are the same) Note: If the voltages are not indicated on the schematic diagram, refer to the voltage charts. 5. Signal path Symbols The arrows indicate the signal path as follows. NOTE : The arrow is DVC unique object. Playback signal path Note: For general information in service manual, please refer to the Service Manual of GENERAL INFORMATION Edition 4 No. 82054D (January 1994). 3. Interpreting Connector indications 1 2 3 1 2 3 Removable connector (Example) Drum servo path Wire soldered directly on board R-Y Y Playback R-Y signal path Recording Y signal path 1 2 3 1 2 3 4 Non-removable Board connector 6. Indication of the parts for adjustments The parts for the adjustments are surrounded with the circle as shown below. Board to Board Connected pattern on board The arrows indicate signal path 7. Indication of the parts not mounted on the circuit board Note: For the destination of each signal and further line connections that are cut off from the diagram, refer to "BOARD INTERCONNECTIONS" "OPEN" is indicated by the parts not mounted on the circuit board. R216 OPEN 4-1 4-2 S40889-01 1 T_RL[+] 4 3 2 3 4 5 GND T_RL[-] 2 1 EDIT EJECT

File name 86736.pdf

SERVICE MANUAL DIGITAL VIDEO CAMERA GR-DV4000US For disassembling and assembling of MECHANISM ASSEMBLY, refer to the SERVICE MANUAL No.86700(MECHANISM ASSEMBLY). SPECIFICATIONS For General Power supply : DC 6.3 V (Using AC Power Adapter/Charger) DC 7.2 V (Using battery pack) Approx. 3.8 W Approx. 4.9 W 74.5 mm x 91 mm x 198 mm (2-15/16" x 3-5/8" x 7-13/16") (with the LCD monitor closed and the viewfinder pushed back in) Approx. 660 g (1.5 lbs) (without cassette, memory card and battery) Approx. 800 g (1.8 lbs) (incl. cassette, memory card and battery) 0°C to 40°C (32°F to 104°F) 35% to 80% ­20°C to 50°C (­4°F to 122°F) 1/4" CCD F 1.2, f = 3.8 mm to 38 mm, 10:1 power zoom lens ш52 mm 3.5" diagonally measured, LCD panel/TFT active matrix system Electronic viewfinder with 0.24" color LCD Monaural For Connectors S S-Video input S-Video output AV Video input Video output Audio input Audio output EDIT Headphone output DV Input/output USB : : Power consumption LCD monitor off, viewfinder on : LCD monitor on, viewfinder off : Dimensions (W x H x D) : Weight : Y: 0.8 V to 1.2 V (p-p), 75 , analog C: 0.2 V to 0.4 V (p-p), 75 , analog Y: 1.0 V (p-p), 75 , analog C: 0.29 V (p-p), 75 , analog Y: 0.8 V to 1.2 V (p-p), 75 , analog Y: 1.0 V (p-p), 75 , analog 300 mV (rms), 50 k, analog, stereo 300 mV (rms), 1 k, analog, stereo ш3.5 mm, 2-pole Stereo 4-pin, IEEE 1394 compliant 5-pin Operating temperature Operating humidity Storage temperature Pickup Lens Filter diameter LCD monitor Viewfinder Speaker For Digital Video Camera Format Signal format Recording/Playback format : : : : : : : : : : : : : : : : : AC Power Adapter/Charger For General Power requirement U.S.A. and Canada Other countries Power consumption Output Charge VTR : : : Cassette Tape speed Maximum recording time (using 80 min. cassette) For Digital Still Camera Storage media Compression system File size Still image : : : DV format (SD mode) NTSC standard Video : Digital component recording Audio : PCM digital recording, 32 kHz 4-channel (12-bit), 48 kHz 2-channel (16-bit) Mini DV cassette SP: 18.8 mm/s LP: 12.5 mm/s SP: 80 min. LP: 120 min. : : : : : AC 120 Vd, 60 Hz AC 110 V to 240 Vd, 50 Hz/60 Hz 23W DC 2 .7 V G, 1.2 A DC 3.6 V G, 1.8 A Specifications shown are for SP mode unless otherwise indicated. E & O.E. Design and specifications subject to change without notice. : : SD Memory Card/MultiMediaCard Still image : JPEG (compatible) Moving image : MPEG4 (compatible) 4 modes (1600 x 1200 pixels/1280 x 960 pixels/1024 x 768 pixels/ 640 x 480 pixels) Moving image : 2 modes (240 x 176 pixels/160 x 120 pixels) Picture quality : 2 modes (FINE/STANDARD) Approximate number of storable images : pg. 39 : GR-DV4000US M3D6L7 COPYRIGHT © 2003 VICTOR COMPANY OF JAPAN, LTD No.86736 2003/05 CONTENTS Important Safety Precautions 1. 3. 4. 5. DISASSEMBLY ...