Teac MCDX25 free download

File name Teac-MCDX25 micro sys.pdf

TEAC MC-DX25 MICRO Hi-Fi SYSTEM PC board shown are viewed from parts side. The parts with no reference number or no parts number in the exploded views are not supplied. As regards the resistors and capacitors, refer to the circuit diagrams contained in this manual. ! 1 SPECIFICATIONS 2 ADJUSTMENT AND CHECKS 3 EXPLODED VIEW AND PARTS LIST 4 PC BOARDS AND PARTS LISTS 5 WIRING DIAGRAM 6 INCLUDED ACCESSORIES 2 3 5 8 16 18 Parts marked with this sign are safety critical components. they must be replaced with identical components - refer to the appropriate parts list and ensure exact replacement. Parts of [ ] mark can be used only with the version designated. MC-DX25 1 SPECIFICATIONS Amplifier Section Output Power (L+R) 5W + 5W Output Power Subwoofer: 15 W Input Sensitivity 300mV 50 to 20,000 Hz Frequency Response : Tuner Section (FM) Frequency Range Sensitivity (S/N30dB) 87.5 MHz to 108.0 MHz 20dBuV Tuner Section (AM) Frequency Range Sensitivity (S/N20dB) 522 to 1620 kHz 54dBuV/m CD Player Section Frequency Responce Signa-to-Noise Ratio Wow and Flutter 20 to 20,000 Hz (+/-1dB) 55 dB Unmeasurable SPEAKER SYSTEM Section L & R speaker : Type : Impedance : Subwoofer: Impedance : Full range flat type 4 ohms 8 ohms GENERAL Power Requirements: Power Consumption: Dimension (W x H x D ): AC230V, 50 Hz 80 W (standby: less than 1.4W) Main Unit 160 x 226 x 86 mm L & R Speaker 140 x 226 x 61mm Subwoofer 160 x 234 x 330mm Weight: (net) Main Unit Subwoofer 1.15 kg 5.4 kg L & R Speaker 0.6 kg(each) Standard Accessories: Remote Control Unit x 1 Subwoofer Cable x 1 Speaker Cable x 2 FM Antenna x 1 AM Antenna x 1 Battery for Remote Control x 1 Wall Mount Adaptor x 3 Wall Mount screw x 10 Tape Plastic Wall Anchor x 10 Template for Wall Mounting x 1 Owner s Manual x 1 Warranty Card x 1 Design and specifications are subject to change without notice. Illustrations may differ slightly from production models. Weight and dimensions are approximate. 2 MC-DX25 2 ADJUSTMENTS AND CHECKS 2-1 TUNER SECTION Use a screwdriver with a plastic or ceramic grip for all adjustment. 2-1-1 FM adjustment 1. Set the function switch to the FM position. 2. Connect the signal generator output through a 75 ohm dummy antenna to "ANT" on MAIN PCB. 3. Connect the oscilloscope to the speaker terminal. 4. Set the signal generator as listed in the alignment chart. 2-1-2 AM adjustment 1. Set the function switch to the AM position. 2. Connect the test loop antenna across the output of the signal generator. 3. Connect the oscilloscope to the speaker terminal. 4. Set the signal generator as listed in the alignment chart. 2-2 Adjustment and Test Points T205 T203 L201 SVC201 T206 L202 T204 SVC202 MC-DX25 MAIN(TUNER) PCB 3 MC-DX25 2-2-1 FM/AM alignment chart ITEM SG SETTING TUNER SETTING ADJUSTMENT POINT ADJUSTMENT FM 1.IFT adjustment 10.7 MHz 1kHz, +/-22.5kHz dev. 87.5MHz 1kHz, +/-22.5kHz dev. 108MHz T205 With 10.7 MHz at zero crossover 2. FM band 87.5MHz L202 90