OLYMPUS C-3040 Zoom free download

File name 1_Cover Page_v1.pdf

REPAIR MANUAL C3040ZOOM - INDEX - SERVER_DIS Service Group, Technical Service Department OLYMPUS OPTICAL CO.,LTD Ver.1

File name B_Disassembly and Assembly Procedure_v1.pdf

B. DISASSEMBLY AND ASSEMBLY PROCEDURE C-3040 Zoom B. DISASSEMBLY AND ASSEMBLY PROCEDURE REMOVAL OF CABINET TOP ASSEMBLY, CABINET FRONT ASSEMBLY AND CABINET BACK ASSEMBLY ... B-2 [2] REMOVAL OF LENS VF AND FLEXIBLE PWB ... B-3 [3] REMOVAL OF LENS ASSEMBLY AND CA1 BOARD ... B-4 [4] REMOVAL OF SY1 BOARD,CA2 BOARD AND ST1 BOARD ... B-4 [5] BOARD LOCATION ... B-5 [1] SERVER_DIS B-1 Ver.1 B. DISASSEMBLY AND ASSEMBLY PROCEDURE C-3040 Zoom [1]REMOVAL OF ABINET TOP ASSEMBLY,CABINET FRON TASSEMBLY AND CABINET BACK ASSEMBLY Disassembly perform as follows (1, 2...23) and assembly perform by reversing the disassembly steps (23, 22...1). Be sure to discharge the main capacitor in procedure 11, then continueu to disassembling. ! Beware of electric shock Danger of electric shock. Use a discharging tool to remove the electrical charge before working. When assembling, attach the spacers to the holder monitor in the order 20, 19, 18 and 21. 22. Holder monitor 20. Spacer monitor light B 17. Screw 1.7 x 4 18. Spacer monitor light 2. Screw 1.4 x 3.5 3. Cover dial 23. LCD 19. Spacer monitor light C 4. Screw 1.7 x 3.5 5. Cabinet top 21. Spacer shield 1. Two screws monitor 1.7 x 3.5 16. Connector 8. Cover card 9. Two screws 1.7 x 8 13. FPC 9. Screw 1.7 x 4 10. Cabinet front 14. Cabinet back 15. FPC 11.Discharge both ends of C5412. (ST1 board side A) 12. Connector & de-solder two wires(Red,White) 7. Three screws 1.7 x 4 6. Open the cover battery. SERVER_DIS B-2 Ver.1 C-3040 Zoom B. DISASSEMBLY AND ASSEMBLY PROCEDURE [2] REMOVAL OF LENS VF AND FLEXIBLE PWB 2. Screw 1.7 x 4 3. Reflector 6. Screw 1.7 x 4 7. Holder mode 1. LCD 9. Two screws 1.7 x 4 12. FPC 8. Screw 1.4 x 3.5 11. Flexible PWB 13. Two screws 1.7 x 4 10. Connector 14. Lens VF 5. Spacer chassis 4. Spacer sheet 17. Connector 16. Holder LED 15. Screw 1.7 x 4 18. Microphone When installing 1. Gear 1 should be positioned correctly. 2. The lens VF should be in the extended position. Ver.1 B-3 SERVER_DIS B. DISASSEMBLY AND ASSEMBLY PROCEDURE [3] REMOVAL OF LENS ASSEMBLY AND CA1 BOARD C-3040 Zoom When assembling, the lens VF and the gear 1 should be positioned correctly before installing the lens assembly. 5. Two screws 6. Screw 2 x 6 2 x 2.5 7. CA1 board B B A C 3. Two FPCs C A 4. PFC Lens CCD Install so that it is perpendicular. 2. Screw 1.7 x 6 1. Three screws 1.7 x 4 [4] REMOVAL OF SY1 BOARD, CA2 BOARD AND ST1 BOARD 1. Screw 1.7 x 4 5. Holder BRKT SY 4. SY1 board 6. Two screws 1.7 x 4 7. Connector 3. Connector 2. Screw 1.7 x 4 10. Connector D 8. CA2 circuit D 11. ST1 board 9. Two screws 1.7 x 4 SERVER_DIS B-4 Ver.1 C-3040 Zoom [5] BOARD LOCATION B. DISASSEMBLY AND ASSEMBLY PROCEDURE SY1 board CA2 board ST1 board CA1 board Ver.1 B-5

File name C_Adjustment Method_V1R3.pdf

C. ADJUSTMENT METHOD C-3040 Zoom C. ADJUSTMENT METHOD [1] TABLE FOR SERVICING TOOLS ... C-2 [2] EQUIPMENT ... C-2 [3] ADJUSTMENT ITEMS AND ORDER ... C-2 [4] SETUP ... C-2 [5] CONNECTING THE CAMERA TO THE COMPUTER ... C-3 [6] USB STORAGE INFORMATION REGISTRATION ... C-4 [7] ADJUST SPECIFICATIONS ... C-5 1. IC501 OSCILLATION FREQUENCY ADJUSTMENT ... C-5 2. 5.1 V (A) VOLTAGE ADJUSTMENT ... C-5 3. 13.0 V (L) VOLTAGE ADJUSTMENT ... C-5 4. 7.0 V (L) VOLTAGE ADJUSTMENT ... C-5 5. LENS ADJUSTMENT ... C-5 6. AWB ADJUSTMENT ... C-6 7. COLOR MATRIX ADJUSTMENT ... C-6 8. CCD DEFECT DETECT ADJUSTMENT ... C-6 9. CCD BLACK POINT DEFECT ADJUSTMENT ... C-6 10. LCD PANEL ADJUSTMENT ... C-7 10-1. LCD H AFC ADJUSTMENT ... C-7 10-2. LCD GAIN ADJUSTMENT ... C-7 10-3. LCD RGB OFFSET ADJUSTMENT ... C-7 10-4. LCD RED BRIGHTNESS ADJUSTMENT ... C-7 10-5. LCD BLUE BRIGHTNESS ADJUSTMENT ... C-8 10-6. LCD TINT ADJUSTMENT (FOR PAL) ... C-8 [8] ADJUST VALUES ... C-9 [9] ADJUST ITEMS ... C-10 SIMENS STAR CHART ... C-11 CHECKING OF LENS UNIT ... C-12 SERVER_DIS C-1 Ver.1/Rev.3 C. ADJUSTMENT METHOD [1] Table for Servicing Tools Ref. No. J-1 J-2 J-3 J-4

File name D_Repair Procedure_v1.pdf

D. REPAIR PROCEDURE C-3040 Zoom D. REPAIR PROCEDURE [1] TROUBLESHOOTING GUIDE ... D-2 POWER LOSS INOPERATIVE ... D-2 TAKING INOPERATIVE ... D-2 NO PICTURE ... D-2 SERVER_DIS D-1 Ver.1 D. REPAIR PROCEDURE C-3040 Zoom [1] TROUBLESHOOTING GUIDE POWER LOSS INOPERTIVE IC301-91 (SCAN IN 0) PULSE INPUT TAKING INOPERATIVE PUSH SHUTTER BUTTON NO CHECK PFC include POWER SW, CN301, R3021 YES IC302-7 (UNREG) LOW CHECK ST1, CA2 IC301-3, 7 (SCAN IN 3) PULSE INPUT NO CHECK PFC include POWER SW, CN301, R3023, R3024 HIGH IC301-81 (VDD) YES LOW CHECK IC302 CN301-7, 8 (P ON, P(A) ON) LOW CHECK IC301, Q3005, Q3006, ST1 HIGH IC301-84 (RESET) HIGH LOW CHECK IC302, R3051 CN301-6, 12, 13 HIGH NO CHECK IC301, CA2, ST1 HIGH IC301-85 (BAT OFF) YES LOW CHECK R3052 SERIAL COMMUNICATION NG CHECK IC301, CA2 HIGH IC301-80 OSCILLATION OK NO CHECK X3001 CHECK CA2 YES IC301-82 OSCILLATION NO CHECK X3002, R3004, C3001, C3002 YES CHECK IC301 NO PICTURE CLK (72MHz) INPUT TO IC102-280 (CLK IN 1) YES MAIN CLOCK FOR SYSTEM OPERATION NO OPERATION IF ABSENT CHECK X1101 OSCILLATOR AND IC111 NO CLK (36 MHz) INPUT TO IC101-132 (CLK IN 1) NG BASIC CPU BLOCK CHECK IC102-278 OK IC101-61 (ZAS) NG ALWAYS APPEARS WHEN CPU, ETC. IS ACCESSED CHECK IF CPU IS READKING PROGRAM, AND CHECK ADDRESS AND DATA BUS OF IC121 REQUEST FOR USE OF DATA BUS FROM ASIC TO CPU NO DMA TRANSMISSION IF ABSENT RECEIVES ZBREQ SIGNAL AND GIVES PERMISSION TO ASIC FOR USE OF DATA BUS NO DMA TRANSMISSION IF ABSENT INCORRECT HANDSHAKING BETWEEN 8-BIT CPU AND RS-232C CHECK EACH INTERFACE OK IC101-52 (ZBREQ) NG OK IC101-56 (ZBGRNT) NG OK IC101-118, 119 (IRL1, 2) NG OK CHECK SOLDERING OF EACH CPU AND MEMORY PIN SERVER_DIS D-2 Ver.1

File name E_Notice of Modification_V1R6.pdf

C-3040ZOOM E. NOTICE OF MODIFICATION 1. Correction of parts number ...E-2 2. Correction of parts number and description...E-3 E-1 Ver.1/Rev.6 E. NOTICE OF MODIFICATION C-3040ZOOM SUBJECT Correction of parts number 2002.12.6 [Content] Corrected the following parts number because of error in writing old GEAR CAM GEAR SHAFT VE083900 VE083955 new VE083901 VE083900 Rev.5 SERVER_DIS E-2 Ver.1 C-3040ZOOM SUBJECT Correction of parts number and description 2003.01.09 [Content] Corrected the following parts and description number because of error in writing old VJ1877000 4Z FRAME # new VJ187900 K-FPC# Rev.6 Ver.1 E-3

File name Maintenance History_V1R2.pdf

Maintenance History MODEL: C-3040 Zoom No. Date of issued 2000.12.11 2000.01.10 Page Detail 1/1 Ver.1 Rev.1 1 set EPD:2/2 PL:2,6 Initial Revised Revised Revised Part number correction (VC153900VE297300) VE121500("NEW" Elimination),Serial number seal addition Part number correction (VJ140600VJ138100) Rev.2 2001.07.19 EPD:2/2 PL:3 SERVER_DIS Technical Service Group, Quality Assurance Department OLYMPUS OPTICAL CO.,LTD

File name Maintenance History_V1R6.pdf

Maintenance History MODEL: C-3040 Zoom No. Date of issued 2000.12.11 2000.01.10 Page Detail 1/1 Ver.1 Rev.1 1 set EPD:2/2 PL:2,6 Initial Revised Revised Revised Part number correction (VC153900VE297300) VE121500("NEW" Elimination),Serial number seal addition Part number correction (VJ140600VJ138100) Rev.2 2001.07.19 EPD:2/2 PL:3 Rev.3 2002.10.07 C-1,12,13,14 EPD:3/3 PL:ALL(6) Addition Make the check procedure of Lens unit Add new parts of Lens unit Revised Revised Revised Corrected misprints Rev.4 Rev.5 2002.10.17 2002.12.06 EPD:1/3,2/3 E-1,2 EPD:2/3,3/3 PL:2/6 Correction of parts number Rev.6 2003.01.09 E-1,3 EPD: 3/3 PL:3/6 Revised Correction of parts number and description SERVER_DIS Technical Section, Support Service Department OLYMPUS OPTICAL CO., LTD

File name Parts List C-3040Zoom_V1R6.pdf

A B C D Cabinet 1 VE208600 VC264500 VC266200 VE210000 1 VC264500 VC264500 VE210200 VE209200 VE087400 VE209800 VC266300 VE087800 VC130600 VC114700 VE202200 VC264500 VC129900 VE089300 VC114700 VC264500 VC114700 VC114700 VE203100 VC264500 VC131300 VC130300 VC264500 VE202500 VC131000 VE088500 VC265900 VE210600 VJ194400 VC114900 VE202400 2 VC265500 VC264500 VC115700 VC115500 VC872300 VC126700 VE297200 VC115800 VC264500 VE209400 VE089900 VC153600 VC116400 3

File name T134-001.PDF

No. T134 - 001 27th Apr. 01 TECHNICAL INFORMATION OE/CPI-TSD C-3040ZOOM New Firmware (v354p-75) Description Changing the firmware of C-3040ZOOM because of improving software PAL : v354p-75 NTSC(GUI:English) : v354u-76 NTSC(GUI:Japanese) : v354-76 Contents The following contents are modified by new software. 1. It hangs-up, if folder name is "DCIM". Countermeasure Install the above new firmware in all C-3040ZOOM that has old firmware version. Version Up Procedure (From Smartmedia Card) 1. 2. 3. 4. 5. 6. 7. Prepare Smartmedia Card for new firmware Make "Firmware" folder in the Smartmedia Card Put new firmware as file name "firmware.bin" in "Firmware" folder. Note! : The file name has to be "firmware.bin", not "v354p-75". Insert the Smartmedia Card in C-3040ZOOM. Select "Play" mode with mode dial. Power ON C-3040ZOOM The current F/W version is indicated on TFT. Select "YES" and Press "OK" button. F/W rewriting is started automatically. It takes about 2 minutes. Note! : Don't touch any key (don't carry out Power OFF) during rewriting F/W because it is fatal damage to C-3040ZOOM. New firmware version is indicated on TFT after finishing the rewriting work. Select "NO" and Press "OK" button. 8. 9. 10. Power OFF C-3040ZOOM. OLYMPUS OPTICAL CO. (EUROPA) GMBH TECHNICAL SUPPORT DEPARTMENT CONSUMER PRODUCTS INTERNATIONAL 1/1

File name T134-002.PDF

No. T134 - 002 30th Apr. 01 TECHNICAL INFORMATION OE/CPI-TSD Countermeasure for Record Error when "Red-Eye Reduction Flash" Mode is being used Model C-3000ZOOM / C-3030ZOOM / C-3040ZOOM / C-2040ZOOM Phenomenon Record error occurs when recording a picture which was taken with "Red-Eye Reduction Flash" mode, and it hangs-up. (This problem occurs seldom.) Cause Noise comes from a "CABINET TOP COVER" when flash is fired. Countermeasure Attach a Spacer Holder, if customer points out this problem. Please refer to the following picture. VC157400 SPACER HOLDER Spare parts number and name VC157400 : SPACER HOLDER OLYMPUS OPTICAL CO. (EUROPA) GMBH TECHNICAL SUPPORT DEPARTMENT CONSUMER PRODUCTS INTERNATIONAL 1/1

File name TID-C3040Z-E002.PDF

TECHNICAL INFORMATION NO. TID-C3040Z-E002 DATE July/26/2001 SUBJECT: Matter of the part number change (finder) Content: There was an error in the part number (finder) of the following model. The part number is changed. Product name: C-3040ZOOM Part number: ERROR CORRECT VJ140600 (LENS,VF(ASSY)) VJ138100 (LENS,VF(ASSY)) Reference: Relation between the model and finder C-2020Z C-2040Z C-3030Z C-3040Z VJ138100 ·> ·> VJ140600 ·> VJ209600 ·> OLYMPUS OPTICAL CO.,LTD TOKYO

File name TID-C3040Z-E003.pdf

TECHNICAL INFORMATION NO. TID-C3040Z-003 DATE Nov.21.2001 SUBJECT: Version up of Firmware Product name: C-3040ZOOM The latest firmware: OLD VERSION V354-76 V354u-76 V354p-75 NEW VERSION V354-77 V354u-77 V354p-76 NTSC(GUI:JAPANESE) NTSC(GUI:ENGLISH) PAL Please refer to repair article for a procedure of rewriting firmware. Change contents (Reason): It changed in order to carry out "SDK" for dentistry photography. The command that can set up a "custom clear setting" from PC was added. This is not related to ordinary users. Change classification: Running change Version up procedure: 1. The binary data of the latest firmware is changed with "firmware.bin" and into smart media. But format smart media into C-3040Zoom and make directory "firmware" copy from binary data. (Make F/W card) 2. Insert the F/W card for C-3040Zoom and turn on the camera at play mode. 3. TFT-LCD was showed F/W version and inquire of rewriting of F/W. Then select "YES" (Character is changed green) and after pressing "OK", rewriting of F/W is started automatically. 4. During the rewriting of F/W, SELF-RED is turned on and showed "EXCHANING" on TFT-LCD. It will take about 2 minutes but please do not operate any key and turn off power. It might have damaged camera body and F/W. 5. After the rewriting of F/W, TFT-LCD was showed as same as procedure 3. Then confirm new version of F/W (example: V354-76=NTSC(GUI:JAPANESE)) and turn off power after selecting "NO". (The discrimination of countermeasure is not showed due to confirm easily. ) OLYMPUS OPTICAL CO.,LTD TOKYO