Sony DVP-S336 free download

File name DVP-S336,345,360 sm Supl 1.pdf

DVP-S336/S345/S360/S365/ S560D/S570D/S745D RMT-D115E/D116A/D117A/D120A/D120E US Model Canadian Model DVP-S360/S560D/S570D SERVICE MANUAL E Model DVP-S360/S560D Chinese Model Hong Kong Model Singapore Model DVP-S345/S745D SUPPLEMENT-1 File this supplement with the service manual. (DDA01649) Korea Model DVP-S336/S745D PX Model DVP-S365 Subject: 1. Service Note is Corrected. 2. POWER BLOCK is Changed. 3. Electrical Adjustment is Corrected. 4. Part List is Changed. SERVICE NOTE (See Service Manual Page 5) 3. HOW TO SERVICE MB-86 BOARD 1) 2) 3) 4) Remove the case from the set. (Refer to 2-1) Remove the mechanism deck. (Refer to 2-6) Remove the MB-86 board. (Refer to 2-9) Set the CK-MD board as shown in Fig. 2. 6) Set the CK-MB board as shown in Fig. 4. 3 CK-MB board 4 Claw 5 CK-MD board 1 MB-86 board 1 Flexible board (CN005) 2 Flexible board (CN001) 2 Two connectors (CN101, 102) 3 Flexible board (CN002) Fig. 2 Fig. 4 5) Set the MB-86 board as shown in Fig. 3. 1 MB-86 board 7) Set the CK-AI board as shown in Fig. 5. 5 Connector (CN103) 4 Connector (CN104) 7 Flexible board (CN103) 6 Flexible board (CN104) CK-MB board 3 Two ground point screws 3 CK-AI board 2 Claw 1 Two connectors (CN101, 102) 2 Stand Fig. 3 Fig. 5 ­2­ 8) Set the three flexible boards (J-6090-100-A) as shown in Fig. 6. MB-86 board 2 Two flexible boards (CN201, 402) Mechanism deck 1 Flexible board (CN202) CK-MD board Fig. 6 9) Set the mechanism deck as shown in Fig. 7. Mechanism deck Fig. 7 ­3­ SECTION 4 PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS - : Points changed portion. HS16S9E (SWITCHING REGULATOR) SCHEMATIC DIAGRAM PAGE INCORRECT D105: Location (C-3). CORRECT D105 1SS270A D101 S1WBA60 D101 S1WBA60 D105 1SS133T-77 R114 470 R114 470 [ 4-53 D315, 613: Location (B-6). 3.6 R611 10k 3.5 Q611 2SA1679 SWITCH P612 2.0A 60V R611 10k 3.6 3.5 Q611 2SA1679 SWITCH P612 2.0A 60V 2.8 2.8 R312 1.8k D315 1SS270A 0.1 0.7 R612 39 1/2W D613 1SS270A R612 D613 39 1/2W 1SS133T-77 \ 0.1 0.7 R312 1.8k D315 1SS133T-77 [ Q312 2SC1740S SWITCH + R317 47k C315 47uF 35V Q312 2SC1740S SWITCH + R317 47k C315 47uF 35V HS16S9F (SWITCHING REGULATOR) SCHEMATIC DIAGRAM PAGE INCORRECT D105: Location (C-3). R114 2.2k CORRECT R114 2.2k D105 1SS270A 4-57 B+ B+ D105 1SS133T-77 D511 S2L20U = D511 S2L20U PC103 TLP721F R401 PC103 TLP721F R401 HS16S9U (SWITCHING REGULATOR) SCHEMATIC DIAGRAM PAGE INCORRECT D105: Location (C-3). CORRECT D105 1SS270A D101 S1WBA60 D101 S1WBA60 D105 1SS133T-77 R114 470 R114 470 [ 4-61 D315, 613: Location (B-6). 3.6 R611 10k 3.5 Q611 2SA1679 SWITCH P612 2.0A 60V R611 10k 3.6 3.5 Q611 2SA1679 SWITCH P612 2.0A 60V 2.8 2.8 R312 1.8k D315 1SS270A 0.1 0.7 R612 39 1/2W D613 1SS270A R612 D613 39 1/2W 1SS133T-77 \ 0.1 0.7 R312 1.8k D315 1SS133T-77 Q312 2SC1740S SWITCH + R317 47k C315 47uF 35V Q312 2SC1740S SWITCH + R317 47k C315 47uF 35V [ ­4­ SECTION 7 ELECTRICAL ADJUSTMENT & : Points added portion. PAGE INCOR

File name MAY NOT PLAY CD,DVD OR VCD.pdf

S Sony Service Company National Technical Services A Division of Sony Electronics Inc. Park Ridge, New Jersey 07656 CONFIDENTIAL Service Bulletin Multi-Disc Players No. CSV-5 Model: DVP-S360, DVP-S560D, DVP-S570D, DVP-C660, DVP-C670D 68R1 Subject: PLAYER MAY NOT PLAY CD/DVD OR VCD Symptom: (111A) Solution: Date: February 4, 2002 The DVD player may not play disc. The display may indicate "No Disc "or C:13:00" Please remove fuse F402 and replace with 0-ohm resistor on MB board (side B). Exchange the resistors R416 and R418. The original values are 150K; change them both to 82K ohms REF F402 R416/ R418 DESCRIPTION CONDUCTOR, CHIP(2012) METL RES 0H 1/10W RESISTOR,CHIP 82K 1/16W PART NUMBER 1-216-295-11 1-216-844-11 There are 2 MB-bds used in these units depending on model. DVPS360, DVPS560D, DVPS570D (MB-86) DVPC660, DVPC670D is (MB-87) NOTE: There are currently 2 versions of MB-86 boards available. The newest version board is modified with F402 omitted from the board. NO MODIFICATION IS REQUIRED. DO NOT REPLACE F401. F401 F402 Old version MB-86 New version MB-86 Reference: HVDK00e007 PRINTED IN USA Multi-Disc Products Service Bulletin No. 68 Multi-Disc Products Service Bulletin No. 68 NOTE: A problem can occur if caution is not taken during the installation of the resistors. They are slightly larger than the originals and if not installed properly, can easily short with another trace. Once a short occurs, it places a heavy DC bias across the tracking coil accompanied by a little puff of smoke. To insure a greater probability of success, the resistors R416 and R418 need to be soldered in absolutely straight. If they are turned in any way, the risk of a short becomes much greater. Also it is important to use as little solder as possible. 1. Measure the resistor between Pin # 21 & Pin # 22 of the Flexible Cable, which is connected with the OPT. (See the figure below.) If the resistance between Pin # 21 & Pin # 22 is below 6 ohms, replace the OPT with a new one. 2. Perform servo adjustment after replacing components and/or optical.

File name MDP REFERENCE DISK.pdf

File name Replacing the Optical Pickup.pdf

Sony Service Company National Technical Services A Division of Sony Electronics Inc. Park Ridge, New Jersey 07656 CONFIDENTIAL Service Bulletin Multi-Disc Players No. CSV-5 Model: DVPS-360, DVPS-560D 65 Subject: REPLACING THE OPTICAL PICKUP Date: June 15, 2000 Symptom: (****) Some of the Optical Pickup replacement KHM-220AAA/J1RP may need reinforcement boards to be cut smaller. The reinforced board may interfere with the Optical Pickup. If this is the case, please check and do the following. Solution: Please confirm the reinforced board that is attached to the 23 Pin- Flexible Cable, which is connecting to the Optical Pickup. Cut the part of the reinforced board shown below. When cutting, avoid damage to other signal lines, cut only the board. After cutting, it has to be 10.0 - 11.5 (mm) if you measure the length of the reinforced board from the point of the Flexible Cable. Part Number A-6062-397-A 8-820-081-03 8-820-081-09 Part Name OPTICAL PICKUP KHM-220AAA/J1RP OPTICAL PICKUP KHM-220AAA/J1RP OPTICAL PICKUP KHM-220AAA/J1RP Reference: HVDK00E003 PRINTED IN USA

File name SYSCON ROM Update.pdf

S Sony Service Company National Technical Services A Division of Sony Electronics Inc. Park Ridge, New Jersey 07656 CONFIDENTIAL Service Bulletin Multi-Disc Players No. CSV-5 Model: DVP-S360, DVP-S560D, DVP-S570D 77 Subject: SYSCON ROM Update Symptom: (1185) Date: December 19, 2001 1. When playing Dual Layer Disc, the video may sometimes stop or is not played back normally if the Dual Layer Disc is not compatible. 2. When playing a .DVD Linear-PCM (Standard Audio of a DVD) after playing a Normal music CD (CDDA), the sound may sometimes disappear. 3. Sometimes, a CD/DVD/Video-CD wil not play. When this occurs, "No Disc" or "C:13:00" errors appear on the display. Note: In the case of Symptom No.3, it is necessary to perform the actions below AND also to perform the actions in Service Bulliten # 68 if they have not been previously performed. Solution: 1. Replace the SYSCON ROM with the improved version. Ckeck the Model Type from the table below. Each Model Type has a different part number for the SYSCON ROM. MODEL TYPE TYPE 1 TYPE 7 TARGET MODEL & DESTINATION DVP-S350: U2 DVP-S363: U2 DVP-S360: U2 DVP-S365: PX DVP-S535D: AU / E / CED / CEK DVP-S536D: CED / CEK DVP-S545D: CN / TW DVP-S560D: E / CA / U2 DVP-S565D: PX DVP-S570D: UC DVP-S735D: AU / CED / CEK / E / EA / RU DVP-S745D: CN / HK / KR / SP / TW TYPE 8 < How to check the DVD players current revision. > a. b. c. Place the DVD Player: in STANDBY Mode. Press first the TITLE Key, then the CLEAR Key, then the POWER Key on the emote commander. Find "Model Name" on the bottom of menu screen. "Model Name" should be shown like "DPX13XXX". Reference:HV01DVK506 PRINTED IN USA MDP Products Service Bulletin No. 78 2. Replace IC 106 with the SYSCON ROM from the table below. MODEL TYPE TYPE 1 TYPE 7 TYPE 8 Ref. No. IC106 IC106 IC106 PART NUMBER 8-759-828-72 6-800-101-01 6-800-102-01 DESCRIPTION IC MR27V1602E-39TPZ060 IC MR27V3202E-A4TPZ060 IC MR27V3202F-A5TPZ060 3. Confirm CHECK SUM by using the SYSCON DIAGNOSTIC in TEST MODE. Each model has a different CHECK SUM as shown in the table below. MODEL TYPE TYPE 1 TYPE 7 TYPE 8 CHECK SUM 3B9F 4ECE 21EF SYSCON ROM VERSION Ver. 2.1 Ver. 1.6 Ver. 1.6 4. Perform all Servo Adjustments after exchanging IC106.