File information: | |
File name: | DP1600_2000_2500_SM_EN_Ver07.part1.rar [preview DP1600 2000 2500] |
Size: | 3000 kB |
Extension: | rar |
Mfg: | Toshiba |
Model: | DP1600 2000 2500 🔎 |
Original: | |
Descr: | Toshiba DP1600 2000 2500 Service Manual |
Group: | Electronics > Office equipment > Copiers |
Uploaded: | 08-12-2007 |
User: | baster1 |
Multipart: | 0 1 |
Information about the files in archive: | ||
Decompress result: | OK | |
Extracted files: | 1 | |
File name DP1600_2000_2500_SM_EN_Ver07.pdf DIGITAL PLAIN PAPER COPIER DP1600/2000/2500 File No. 31100011 R0111216600-TTEC Copyright 2000 TOSHIBA TEC CORPORATION GENERAL PRECAUTIONS REGARDING THE INSTALLATION AND SERVICE FOR DP1600/2000/2500 SERIES The installation and service should be done by a qualified service technician. 1. Transportation · When transporting/installing the copier, employ two persons and be sure to use the positions as indicated below. The copier is fairly heavy and weighs approximately 50 kg (110 lb), therefore pay full attention when handling it. 4 portions 2. Installation · · · · · · Be sure to use a dedicated outlet with AC 115 or 120V/15A (220V, 230V, 240V/10A) or more for its power source. The copier must be grounded for safety. Never ground it to a gas pipe or a water pipe. Select a suitable place for installation. Avoid excessive heat, high humidity, dust, vibration and direct sunlight. Also provide proper ventilation as the copier emits a slight amount of ozone. To insure adequate working space for the copying operation, keep a minimum clearance of 80 cm (32") on the left, 80 cm (32") on the right and 10 cm (4") in the rear. After having installed the copier, be sure to push the carrying handles into the copier. 3. Service of Machines · · · · · · Basically, be sure to turn the main switch off and unplug the power cord during service. Be sure not to touch high-temperature sections such as the exposure lamp, the fuser unit, the damp heater and their periphery. Be sure not to touch high-voltage sections such as the chargers and the high-voltage transformer. Be sure not to touch rotating/operating sections such as gears, belts, pulleys, fans, etc. When servicing the machines with the main switch turned on, be sure not to touch live sections and rotating/operating sections. Avoid exposure to laser radiation. Use suitable measuring instruments and tools. December 2000 © TOSHIBA TEC 1600/2000/2500 GENERAL PRECAUTIONS · Avoid exposure to laser radiation during servicing. Avoid direct exposure to beam. Do not insert tools, parts, etc. that are reflective into the path of the laser beam. Remove all watches, rings, bracelets, etc. that are reflective. 4. Main Service Parts for Safety · The breaker, door switch, fuse, thermostat, thermofuse, thermistor, etc. are particularly important for safety. Be sure to handle/install them properly. 5. Cautionary Labels · During servicing, be sure to check the rating plate and the cautionary labels such as "Unplug the power cord during service", "Hot area", "Laser warning label" etc. to see if there is any dirt on their surface and whether they are properly stuck to the copier. 6. Disposition of Consumable Parts/Packing Materials · Regarding the recovery and disposal of the copier, supplies, consumable parts and packingm a terials, it is recommended to follow the relevant local regulations or rules. 7. When parts are disassembled, reassembly is basically the reverse of disassembly unless otherwise noted in this |
Date | User | Rating | Comment |