PANASONIC TX-29PM1P free download

File name 50H0000277 - FBT exchange.pdf

SERVICE DIRECTION For exchanging FBT in CP-521F chassis Please use below service direction during exchange FBT: to without bleeder resistor. FBT type with bleeder resitor 1302.2001B w/o bleeder resistor 1302.2001C In this case should be applied special Bridge PCB and correct software version for improving spot problem. Step for exchanging FBT: No 1. Action Open Back Cover and change FBT. Connect correctly H/V, Screen and Focus wires. Find connector P501 and take out from Main and CRT PCBs (board in type). Part Desc. 1302.2001C [50H0000277] BIC-05T-25T+ULW=500 [4850705N14] Remark - 2. 3. Insert and solder new CONNECTOR to loc. P501 of Main PCB. YH025-05+YST250+ULW=500 [4950705008] 4. Insert and solder Bridge PCB to loc. P501A of CRT PCB (polarity as show on the picture). Connect new Connector from loc. P501 to Conn Wafer loc. PK02 (Bridge PCB). - Page 1 5. Insert connector PK03 (Bridge PCB) to loc. R850 (+8V line Main PCB). AWG22 7/0.26 BK 5-500-5 [WP0BK5015] Use hole of R850 for connect connector PK03 6. Use Tie Cable to ass'y connectors as show on the photo. NYLON66 DA100 [4856812001] Tie Cable 1 Tie Cable 2 7. Updata the software version Updating method and correct software version ­ pls see: 8. Before closing Back Cover set must be readjust (screen, focus etc.) - Page 2

File name Manual_Daewoo_Flashing_tool.pdf

Manual_Daewoo_Flashing_tool REVISION 02.00 Chassis CP-521F 1. Hardware Installation a. Turn Off computer b. Connect I2C Interface Please connect I2C Interface to the LPT computer slot. ! This installation requires ­ Microsoft.NET Framework Version 2.0 - it is available at http://www.microsoft.com/net LPT Slot I2C Interface connected - c. Turn On computer. 2. Software installation - Run DF1_2Setup.exe file. And next follow the installer command - Important is the last step of installation ­ Restart computer now 1 of 4 Manual_Daewoo_Flashing_tool REVISION 02.00 Chassis CP-521F 3. Software configuration. Choose - Settings -> Interface -> Single Master (default Single Master) Choose - Settings -> Transmission speed -> 50kbps (default is 100kbps, but with this speed with some hardware configuration errors can appear ­ at that time please change transmission speed to 50kbps ) Choose - Settings -> IC type -> N1D 128 (see at table 5.) Choose - Settings -> Port -> LPT1 (depends on your hardware configuration. Normally is LPT1) 2 of 4 Manual_Daewoo_Flashing_tool REVISION 02.00 Chassis CP-521F 4. Chassis CP-521F family MICOM programming a) By Open Hex File button choose correct version of MICOM software (hex software can be at different directory, than you can see on the picture depends on where you placed hex file for flashing downloaded before). Default c:\Program Files \Daewoo Flashing 1.2\HEX files\... b) Please connect I2C Interface to the chassis Do not connect SingleMaster interface to TV Set without connecting it to the computer c) Please connect chassis to the power supply d) Turn On the chassis (chassis should be assembled with a CRT) e) STBY led should be lighted Important: Please observe led when led is starting to light after 3-4sec. from that push button Flash! ­ flashing process well started. After some elapsed time you should receive OK. Information for all indicators and Flashing succesfully completed! f) Turn Off the chassis ­ programming process is finished. 3 of 4 Manual_Daewoo_Flashing_tool REVISION 02.00 Chassis CP-521F 5.MICOM types Table 5. MODELS TX-29PM1D TX-29PM1F TX-29PM1P Part Number TDA21HD01-W TDA21HD01-W TDA21HD01-E MICOM type N1D 128 N1D 128 N1D 128 SW file CP521F_PANA_10_3_WEST_ver00_3614_03_06.hex CP521F_PANA_10_3_EAST_ver00_3614_03_06.hex Chassis CP-521F 6. Remark Do not connect SingleMaster interface to TV Set without connecting it to the computer. If during programming time you receive Error information * please try program one more time (push Flash! Button). (sometimes especially at Erasing Flash process few times of Start program is needed), * important is timing ­ Turn On chassis and Start flashing (time of pushing Flash! Button), see point 4-e * try change transmission speed (point 3) * check MICOM supply voltage (digital part 1,8V and 3,3V) all must be correct. 4 of 4

File name PCZ0409021C2.pdf

CONTENTS SAFETY PRECAUTIONS ... 2 SERVICE HINTS ... 3 VOLTAGE CHECK AND OPTION BYTES ... 4 WAVEFORM PATTERN TABLE... 5 ALIGNMENT SETTINGS ... 6 BLOCK DIAGRAMS... 7 PARTS LOCATION... 9 REPLACEMENT PARTS LIST... 10 SCHEMATIC DIAGRAMS... 15 CONDUCTOR VIEWS ... 17 SAFETY PRECAUTION GENERAL GUIDE LINES 1. 2. It is advisable to insert an isolation transformer in the a.c. supply before servicing a hot chassis. When servicing, observe the original lead dress in the high voltage circuits. If a short circuit is found, replace all parts that have been overheated or damaged by the short circuit. After servicing, see that all the protective devices such as insulation barriers, insulation papers, shields and isolation R-C combinations are correctly installed. When the receiver is not being used for a long period of time, unplug the power cord from the a.c. outlet. Potentials as high as 29,5kV are present when this receiver is in operation. Operation of the receiver without the rear cover involves the danger of a shock hazard from the receiver power supply. Servicing should not be attempted by anyone who is not familiar with the precautions necessary when working on high voltage equipment. Always discharge the anode of the tube. After servicing make the following leakage current checks to prevent the customer from being exposed to shock hazard. Unplug the a.c. cord and connect a jumper between the two prongs of the plug. Turn on the receiver's power switch. Measure the resistance value with an oh

File name PCZ0604035PE.pdf

Order NO. PCZ0604035PE Parts Change Notice Colour Television Chassis CP-521F Models: TX-29PM1D, TX-29PM1F, TX-29PM1P Please revise the original parts list in the Service Manual to confirm to the change(s) shown herein. If new part numbers are shown, be sure to use them ordering parts. Reason for Change *The circled item indicates the reason. If no marking, see the Notes in the bottom column · 1. Improve performance 2. Change of material or dimension 3. To meet approved specification 4. Standardization 5. Addition 6. Deletion 7. Correction 8. Other Interchangeability Code **The circled item indicates the interchangeability. If no marking, see the Notes in the bottom column. Parts Set production Original or new parts may be used in early or late production set. A Original Early Use original parts until exhausted, then stock new parts. New Late Original parts may be used in early production sets only. New parts may be used in early or late production sets. B Original Early Use original parts where possible, then stock new parts. New Late New parts only may be used in early or late production sets. · C Original Early Stock new parts. New Late D E Original New Other Early Late Original parts may be used in early production sets only. New parts may be used in late production sets only. Stock both original and new parts. Part Number Ref. No. Original Part No. Part Name & Descriptions FBT (1302.2001B) New Part No. Part Name & Descriptions SERVICE KIT incl. FBT (1302.2001C) Notes T402 50H0000277 TZS9EK038 1C

File name TX-29PM1DEUSVC.txt

TX-29PM1D/TX-29PM1F/TX-29PM1P EU SVC AV_Products Color_TV