JBL GTO14001 free download

File name Jbl-GTO14001 caramp.pdf

GTO 14001 1 CHANNEL POWER AMPLIFIER SERVICE MANUAL JBL Consumer Products 250 Crossways Park Dr. Woodbury, New York 11797 Released 2008 Discontinued XXXX Rev0 3/2008 GTO14001 - CONTENTS SPECIFICATIONS ...1 PACKING...2 CONTROL/INSTALLATION DRAWINGS...3 CONTROL/INSTALLATION INSTRUCTIONS...4 BASIC TROUBLESHOOTING...5 EXPLODED VIEW/PARTS LIST...6 AMPLIFIER BLOCK DIAGRAM...7 ELECTRICAL PARTS LIST ...8 P.C.B. DRAWINGS...13 IC/TRANSISTOR PINOUTS...20 SCHEMATICS...21 GTO 14001 Specifications Output Power: (14.4V supply) Signal-to-noise ratio: Dynamic power: Frequency response: THD+N 1KHz LPF=22KHz Input Impedance Maximum input signal: Maximum sensitivity: Bass Boost @ 20-100Hz DC Offset Output regulation: Idle Current @ 2 ohms Max Current Draw Remote Operating Voltages Turn-on delay time Circuit Protection Operating voltage range Dimensions: Fuses: 1200W RMS x 1 channels @ 4 ohms; 1% THD + N 1500W RMS x 1 channels @ 2 ohms; 1% THD + N 77dBA (reference 1W into 4 ohms) 108dBA (reference rated power into 4 ohms) 1800W @ 2 ohms 20Hz ­ 300Hz (­3dB) 0.05% (rated power @ 4 ohms) >20K ohms 6.0V 100mV 0-12dB (±2dB) <30mV .03dB @ 4 ohms 1.8A 140A @ 2 ohms ON 5V OFF 3.5V 2-3 sec Temperature (80±5C), Short circuit (8-16V) 18 9/16 x 10 3/8 x 2 1/8" (470 x 263 x 53mm) (4) x 40A JBL continually strives to update and improve existing products, as well as create new ones. The specifications and details in this and related JBL publications are therefore subject to change without notice. 1 GTO14001 2 GTO14001 4x 2x 1x 1x 1x 4x 10-3/8" 263mm 0 1 2 2-1/8" 53mm 18-9/16" 470mm D 34 9 A 8 5 6 7 A B C 1" 25mm B A B C D A 1-5/8" 40mm 8 3 GTO14001 GTO14001 CAR AUDIO SUBWOOFER AMPLIFIER OWNER'S MANUAL Installation Warnings and Tips · Disconnect the negative (­) lead from your vehicle's battery. · At the installation sites, locate and make a note of all fuel lines, hydraulic brake lines, vacuum lines and electrical wiring. Use extreme caution when cutting or drilling in and around these areas. · Choose a safe mounting location away from moisture. · Make sure there is sufficient air circulation at the mounting location for the amplifier to cool itself. · Mount the amplifier, using the supplied hardware. Specifications · 1200W RMS x 1 channel @ 4 ohms and 1% THD + N* · 1500W RMS x 1 channel @ 2 ohms and 1% THD + N* · THD + N: 0.05% (rated power @ 4 ohms) · Signal-to-noise ratio: 77dBA (reference 1W into 4 ohms)* · Signal-to-noise ratio: 108dBA (reference rated power into 4 ohms) · Frequency response: 20Hz ­ 330Hz (­3dB) · Max power: 1500 watts * CEA-2006A-compliant 0 Speaker Output Connectors ·