Sony XM1002HX free download

File name Sony-XM1002HX caramp.pdf

XM-1002HX SERVICE MANUAL Ver 1.1 2001. 08 US Model Canadian Model AEP Model UK Model E Model SPECIFICATIONS AUDIO POWER SPECIFICATIONS (US model) POWER OUTPUT AND TOTAL HARMONIC DISTORTION 100/50 watts per channel minimum continuous average power into 4 ohms, both channels driven from 20 Hz to 20 kHZ with no more than 0.04% total harmonic distortion per Car Audio Ad Hoc Committee standards. Other Specifications Circuit system OTL (output transformerless) circuit Pulse power supply Inputs RCA pin jacks High level input connector Outputs Speaker terminals Through out pin jacks Speaker impedance 1* ­ 8 (stereo) 2* ­ 8 (when used as a bridging amplifier) Maximum outputs (HI-CURRENT/HI-VOLTAGE) 120/230 W x 2 (at 4 ) 380/580 W (monaural) at 4 Rated outputs (HI-CURRENT/HI-VOLTAGE) (supply voltage at 14.4 V) 50/100 W x 2 (20 Hz ­ 20 kHz, 0.04% THD, at 4 ) 70/140 W x 2 (20 Hz ­ 20 kHz, 0.1% THD, at 2 ) 140/280 W (monaural) (20 Hz ­ 20 kHz, 0.1% THD, at 4 ) Frequency response 5 Hz ­ 50 kHz ( +0.5 dB) ­3 Harmonic distortion 0.005% or less (at lkHz, 4 ) Input level adjustment range 0.2 ­ 4.0 V (RCA pin jacks) 0.4 ­ 8.0 V (High level input) High-pass filter 50 ­ 200 Hz, ­12 dB/oct Low-pass filter 50 ­ 200 Hz, ­12 dB/oct Low boost 0 ­ 10 dB (40 Hz) Power requirements 12 V DC car battery (negative ground) Power supply voltage 10.5 ­ 16 V Current drain at rated output : 26 A (4 HI-VOL TAGE mode) Remote input : 2 mA Dimensions Approx. 258 x 50 x 320 mm (10 l/4 x 2 x 12 5/8 in.) (1/h/p) not incl. projecting parts and controls Mass Approx. 3.3 kg (7 lb, 4 oz.) not incl. accessories Supplied accessories Mounting screws (4), Terminal cap (1) Design and specifications are subject to change without notice. * HI-CURRENT only STEREO POWER AMPLIFIER 9-925-785-12 2001H0400-1 © 2001. 8 Sony Corporation e Vehicle Company Shinagawa Tec Service Manual Production Group 1 TABLE OF CONTENTS Specifications ... 1 1. SERVICING NOTE ... 2 2. GENERAL ... 3 3. DISASSEMBLY 3-1. Bottom Plate, Panel (Front), Panel (Rear) Removal ... 5 3-2. Amplifier Board Removal ... 5 4. ELECTRICAL ADJUSTMENT ... 6 5. DIAGRAMS 5-1. Block Diagram ... 7 5-2. Printed Wiring Boards ... 9 5-3. Schematic Diagram ... 13 6. EXPLODED VIEW ... 15 7. ELECTRICAL PARTS LIST ... 16 SECTION 1 SERVICING NOTE CANCELLING THE PROTECTOR DURING SERVICING Cut JW219 on the amplifier board to cancel the protector. After servicing always be sure to return JW219 to its original state. T901 C801 JW89 IC902 JW219 PROTE