Text preview for : DX-1A.pdf part of SONY DX-1A Sony DX-1A SERVICE MODE
Back to : DX-1A.pdf | Home
Self Diagnosis
Supported model
SERVICE MANUAL
MODEL NAME REMOTE COMMANDER DESTINATION
DX-1A CHASSIS
CHASSIS NO.
KV-32XBR450 KV-32XBR450
RM-Y184 RM-Y184
US CND
SCC-S47D-A SCC-S48D-A
KV-32XBR450
RM-Y184
TRINITRON® COLOR TELEVISION
9-965-898-01
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
SECTION 4: CIRCUIT ADJUSTMENTS ELECTRICAL ADJUSTMENTS BY REMOTE COMMANDER
Use the Remote Commander (RM-Y183, RM-Y184) to perform the circuit adjustments in this section. Test Equipment Required: 1. Pattern generator 2. Frequency counter 3. Digital multimeter 4. Audio oscillator
4-1. SETTING THE SERVICE ADJUSTMENT MODE
1. Standby mode (Power off). 2. Press the following buttons on the remote commander within one second of each other: Channel 5 Sound Volume + Power DISPLAY
4-2. MEMORY WRITE CONFIRMATION METHOD
1. After adjustment, pull out the plug from the AC outlet, then replace the plug in the AC outlet again. 2. Turn the power switch ON and set to Service Mode. 3. Call the adjusted items again to confirm they were adjusted.
SERVICE ADJUSTMENT MODE VIEW
Device Item Register Item 2150P-1 SBOT 0 Data Item +7 SERVICE TV
4-3. REMOTE ADJUSTMENT BUTTONS AND INDICATORS
WSL: 0
F/A FLAG: CBA FLAG:
WRITE INTO MEMORY
DEVICE UP
READING THE MEMORY
1. Enter into service mode. 2. Press 0 on the remote commander. 3. Press ENTER to read memory.
ITEM UP ITEM DOWN
DATA UP DATA DOWN DEVICE DOWN EXECUTE READ MEMORY
ADJUSTING THE PICTURE
1. 2. 3. 4. 5. Enter into service mode Press 2 or 5 on the remote to select the device item. Press 1 or 4 on the remote to select an item. Press 3 or 6 on the remote to change the data. Press MUTING then ENTER to write into memory.
TEST RESET
4-1.1 RESETTING THE DATA
Note: Be careful when using the remote! It will clear and re-initialize ALL NVM data including deflection adjustment data if not reset properly as follows:
RESETTING THE DEFLECTION NVM DATA
1. Enter into service mode. 2. Press 7 , then MENU , and then press ENTER on the remote.
RESETTING THE SYSTEM NVM DATA
1. Enter into service mode. 2. Press 7 , then 9 , and then press ENTER on the remote.
RESETTING THE SYSTEM NVM DATA
1. Enter into service mode. 2. Press 8 and then press ENTER on the remote.
RM-Y183 (KV-32HS20/36HS20/36HS20H ONLY)
-- 18 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
WRITE INTO MEMORY
DEVICE UP
ITEM UP ITEM DOWN
DATA UP DATA DOWN DEVICE DOWN EXECUTE READ MEMORY
TEST RESET
RM-Y184 (KV-32XBR450/36XBR450/36XBR450H ONLY)
-- 19 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
SERVICE DATA LISTS
DX1A-2001* Service List ------ Contents & Notes
Category Number & Name #1 # 2-1 # 2-2 # 3-1 # 3-2 # 3-3 # 3-4 # 4-1 # 4-2 # 4-3 #5 #6 #7 #8 #9 # 10 # 11 # 12 # 13 # 14 # 15 # 16 # 17 3D-COMB CXA2103-1 (Main) CXA2103-2 (Sub) CXA2150P-1 CXA2150P-2 CXA2150P-3 CXA2150P-4 CXA2150D-1 CXA2150D-2 CXA2150D-3 CXA2151 D-CONV CXA2026 AP TRUS MID1 MID2 MID3 MID5 OSD SNNR ID1 CCD&VCHIP Device Name mPD64082 CXA2103Q Device Reference Number IC3501 / BC-board IC3048 (Main) / B-board IC3110 (Sub) / B-board IC201 / A-board Slave Address B8h (W) & B9h (R) W&R: Write & Read 9Ah 9Eh 86h Comment
CXA2150AQ
CXA2150AQ CXA2151Q CXA8070P CXA2026AS BH3868AFS NJM2180M CXD9509AQ CXD9509AQ CXD9509AQ CXD9509AQ M306V2ME-153FP mPD64082 CXA2103Q CXA2150Q CXD2085M CXP85840A-039Q
IC201 / A-board IC3001 / B-board IC5513 / D-board IC5511 / D-board IC7001 / A-board IC4101 / S-board IC3408 / B-board IC3408 / B-board IC3408 / B-board IC3408 / B-board IC701 / A-board IC3501 / BC-board IC3048 (Main) / B-board IC201 / A-board IC3603 / B-board IC3602 (Main) / B-board IC3601 (Sub) / B-board
86h 84h DEh 8Eh 82h 2Eh 2Eh 2Eh 2Eh 2Eh Controlled through CXA1315M ( IC4103 / S-board / 48h ) Controlled through MID-XA Micro ( IC3090 / B-board / 64h ) Controlled through MID-XA Micro ( IC3090 / B-board / 64h ) Controlled through MID-XA Micro ( IC3090 / B-board / 64h ) Controlled through MID-XA Micro ( IC3090 / B-board / 64h )
60h DX1A-2001 System Micro {V1.0} B8h (W) & B9h (R) 9Ah 86h 40h 68h (Main) 6Ch (Sub) CCD&Vchip Micro (V2.14)
# 18 OP # 19 ID DX1A-2001 System Micro & Notes for Services DX1A-2001 MID-XA Micro
M306V2ME-153FP IC701 / A-board 60h DX1A-2001 System Micro {V1.0} M306V2ME-153FP IC701 / A-board 60h DX1A-2001 System Micro {V1.0} M306V2ME-153FP (MASK), Software Version 1.0, IC701/A-board (Slave Adress: 60h) The system micro name, software&patch versions, and the status of NVM devices are displayed only when in the service catergory
MB94918RPF-G-137-BND (MASK), Software Version 12/08/00, IC3090/B-board (Slave Address: 64h) DX1A-2001 CCD&Vchip Micros CXP85840A-039Q (MASK), Software Version 2.14, IC3602/B-board (Main/Slave Address: 68h) & IC3601/B-board (Sub/Slave Address: 6
Note: * This service list is used for DX1A-2001 ONLY. Some service data is the same in DX1A-2001 & 2000, as noted in the data sheets.
-- 20 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#1): 3D-COMB / mPD64082 (Part-1/4)
Device Name: mPD64082GF { 3D-Comb Filter / NEC } / IC3501 (BC-board) / P/N: 8-759-594-44 (SB#: V7372) Slave Address: B8h (Write Address) / B9h (Read Address)
Register No & Name Control Register Function & Link Data Type Data Range
Standard
Data Initial/Average Setting
(32V&36V CRTs) UHF/VHF & CVideo
Non-standard Standard
Comment CVideo (CV): CVideo1~4 inputs SVideo (SV): SVideo1~3 inputs C: Common data
SVideo
Non-standard
0 1 2 3 4 5 6 7 8 9 10 11 12
NRMD YAPS CLKS NSDS MSS KILS CDL DYCO DYGA DCCO DCGA YNRL CNRL
Operation mode setting Y-output correction (V-aperture compensation & Y-peaking filtering) System clock setting Selection for standard/non-satndard signal processing Selection for inter-frame/inter-line processing Killer processing selection C-signal phase with respect to the Y-signal (Fine adjustment at 70 ns/step)
NRMD Setting-based Control Table for DYCO, DYGA, DCCO, DCGA
0~3 C C 0~3 0~3 0~3 0~3 0~3 0~7 0~15 0~15 0~15 0~15 0~3 0~3 0~3 0~3 0~3
0 3 1
1
3
3
UHF/VHF & CVideo
Standard Non-standard Standard
SVideo
Non-standard
C C C
0 0 1 3
NRMD = 0
0
0
0
NRMD = 1
NRMD = 2
NRMD = 3
DY detection coring level (Y motion detection coring) DY detection gain (Y motion detection gain) DC detection coring level (C motion detection coring) DC detection gain (C motion detection gain) Frame recersive YNR nonlinear filter limit level Frame recersive CNR nonlinear filter limit level Hysteresis for Hsync non-standard signal detection (out-of-Hsync intra-field) Sensitivity for Hsync non-standard signal detection (out-of-Hsync intra-field) Sensitivity for frame non-standard signal detection (out-of-Hsync inter-frame)
VM&SNNR Setting-based Control Table for VAPG & VAPI VAPG= VAPG1 - VAPG2
C C
2 10 5 5 1 1
UHF/VHF
2 10 5 5
2 10 5 5
2 10 5 5
Video1~4
Video5&6
13 VTRH 14 VTRR 15 LDSR
1 1 2
VM = Off
1 1 2
VM = Low
1 1 2
VM = Mid
Video1~4: CVideo1~4 & SVideo1~3 inputs Video5&6: YPbPr-480i/480p/1080i inputs
VAPG1 Data Based on MENU/VM Setting
VM = High
16 VAPG 17 VAPI 18 YPFT 19 YPFG
V-aperture compensation gain V-aperture compensation convergence point
SNNR Setting-based Control Table for YPFT & YHFG
0~7 0~31 0~3 0~15
0 4 0 7
2 4
SNNR = 0
3 4
SNNR = 1
4 4 (32V) or 8 (36V)
SNNR Setting (-Offset)
SNNR = 2
This setting continues to the next page. {Initial/CBA Data = 8}
SNNR = 3
Y peaking filter (BPF) center frequency Y peaking filter (BPF) gain
0 0
0 1
0 2
0 3
Note: The same 3D-COMB service data is used for DX1A-2001&2000.
DX1A-2001&2000 SERVICE LIST (#1): 3D-COMB / mPD64082 (Part-2/4)
Register No & Name
SNNR = 0
Data Initial/Average Setting
(32V&36V CRTs) VAPG2 Data Based on SNNR/Offset-setting
SNNR = 1 SNNR = 2 SNNR = 3
Comment
#16 VAPG (cont.
0
0
0
0
Note: The same 3D-COMB service data is used for DX1A-2001&2000.
-- 21 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#1): 3D-COMB / mPD64082 (Part-3/4)
Register No. & Name
Control Register Function & Link
SNNR Setting-based Control Table for YHCO & YHCG
Data Type
Data Range
SNNR = 0
Data Initial/Average Setting
(32V&36V CRTs) SNNR = 1 SNNR = 2 SNNR = 3
Comment (Not SNNR Offset Data) YHCO&YHCG settings are sent directly to 3D-Comb device.
20 21 22 23 24
YHCO YHCG HSSL VSSL ADCL
Y output high frequency component coring Y output high frequency component coring gain Hsync slice level Vsync slice level ADC clock delay
NRMD Setting-based Control Table for D2GA
C C C
0~3 0, 1 0~15 0~15 0~3 0~7 0~15 0, 1 0, 1 0, 1 0~255 0, 1 0, 1 0, 1 0, 1 0, 1 0~7 0~15 0~15 0, 1 0~3 0~63 0~7
1 0 12 8 3
NRMD = 0
1 0
C: Common data
1 0
1 0
NRMD = 1
NRMD = 2
NRMD = 3
25 D2GA 26 KILR 27 OP1
Moving detection gain Killer detection reference Option1: Selection of comb filter & recursive noise reduction types Noise reduction on/off SNNR control on/off Noise level detection data H-PLL filter (Must be set to 1 when MN signal is input.) Burst PLL filter Burst extraction gain PLL loop gain
C C
4 3 1
UHF/VHF
4
4
4
CVideo1
SVideo1
28 NR1 29 NR2 30 WSL 31 HPLL 32 BPLL 33 FSCF 34 PLLF 35 CC3N 36 HDP
C C C C C
0 0 1 1 0 1
UHF/VHF
0
1
This setting continues to the next page.
1 Byte Data from Read Register WSL
Video1~4
Video5&6
Selection of a line-comb filter C separation filter characteristic Fine adjustment of the system H-phase C Internal burst gate start position C 37 BGPS {Gate Start Position from Hsync center = 0.25 x BGPS + 2 Internal burst gate width 38 BGPW C {Gate Width = 0.25 x BGPW + 0.5 (ms)} 39 TEST Test bit {0: Normal mode, 1: Test mode (forbidden setting)} C 40 WSC Amount of noise detection coring C 41 LIND 42 PFGO DRC-M line-doubling setting for non-standard signals (YPFG offset at GR on) --- Not used for DX1A
Micro
0 5 4 10 0 1
0
0
Video1~4: CVideo1~4 & SVideo1~3 inputs Video5&6: YPbPr-480i/480p/1080i inputs
UHF/VHF & Video1~4
Video5&6
0 3
---
2 (Not used for DX1A)
This setting is used for non-standard signals such as Play Station signals.
Note: The same 3D-COMB service data is used for DX1A-2001&2000.
DX1A-2001&2000 SERVICE LIST (#1): 3D-COMB / mPD64082 (Part-4/4)
Register No & Name
CVideo2
Data Initial/Average Setting
(32V&36V CRTs) SVideo2 CVideo3 SVideo3
Comment
#28 NR1 (cont.)
0
1
0
1
Note: The same 3D-COMB service data is used for DX1A-2001&2000.
-- 22 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#2-1): CXA2103-1 {Main}
Device Name: CXA2103Q { NTSC-YCT (Chroma Decoder) / SONY } / IC3048 (B-board) / P/N: 8-752-089-50 (SBorSD#: NA) Slave Address: 9Ah { Main }
Register No & Name Control Register Function & Link Data Type Data Range Data Initial Setting & [Average Data]
(32V&36V CRTs) UHF/VHF & Video
P&P-Left (M)-DRC P&P-Left (M)-1080i
Data Initial/Average Setting
(32V&36V CRTs)
Note
YPbPr-480i
P&P-Left (M)-DRC P&P-Left (M)-480i
0 1 2 3 4 5
YLEV CLEV SCON SCOL SHUE YDLY
Y-Out gain Cb&Cr-Out gains Sub contrast Sub color Sub hue Y/C delay time
SNNR Data-related Settings
0~63 0~63 Adj. Adj. Adj. 0~15 0~15 0~15 0~3 0~15 0~3 0~3 0~3 0~3 0, 1 0, 1 0, 1 0, 1 0~3 0~3 0, 1 0, 1 0~15
23 17
27* 55*
UHF/VHF
28 32
Video
31* 31*
Video: CVideo1~4 & SVideo1~3 Inputs P&P-Left (M)-1080i&480i: If P&P-Left is 1080i/480p signal, the signal from the main chroma decoder is sent to MID/VDO input. *: Settings not used
7 [7] 7 [7] 7 [Adj.-2steps] 0
UHF/VHF CVideo
7 [7] 7 [7] 7 [Adj.-2steps] 0
SVideo YPbPr 480i
Adj.: Adjusted data [Adj.-2steps]: The adjusted data - 2 steps
SNNR=0 (-offset)
SNNR=1 (-offset)
SNNR=2 (-offset)
SNNR=3 (-offset)
6 SHAP 7 SHF0 8 PREO 9 BPF0 10 BPFQ 11 BPSW 12 TRAP 13 LPF 14 AFCG 15 CDMD 16 SSMD 17 HMSK 18 HALI 19 PPHA
Sharpness Sharpness f0 selector Sharpness pre/over-shoot ratio Chroma band filter f0 setting Chroma band filter Q setting Chroma band filter on/off Y bolck chroma trap filter on/off YPbPr-Output LPF on/off AFC Loop Gain (PLL between Hsync & HVCO) V countdown system mode selector H&Vsync slide level setting Masking of macrovision signal on/off H automatic adjustment on/off H TIM phase adjustment for video
6 0 3 3 0 1 0 0
UHF/VHF
4 0 0 0 3 0 0 0
Video
4 0 0 0 3 0 0 0
YPbPr 480i
4 0 0 0 3 0 0 0
0
1
2
3
CVideo: CVideo1~4 Inputs SVideo: SVideo1~3 Inputs
1 3 0 1 0 7
P&P-Left (M)-DRC
0 3 0 1 0 7
P&P-Left (M)-1080i
0 3 0 1 0 7
YPbPr-480i
P&P-Left (M)-DRC P&P-Left (M)-480i
UHF/VHF & Video
20 CBOF 21 CROF
Cb-Offset1 of Cb IN (Pin34) Cb-Offset2 of EXT Cb (Pin38) Cr-Offset1 of Cr IN (Pin35) Cr-Offset2 of EXT Cr (Pin39) Auto-pedestal Inflection Point DC Transmission Ratio
0~(31)~63 0~(31)~63
31 31
UBLK = 0
31* 31*
UBLK = 1
31 31
UBLK = 2
31* 31*
UBLK = 3
*: Settings not used (31): The center setting = 31
P&P & Favorite
UBLK = 4 UBLK = 5 UBLK = 6 UBLK = 7
CXA2150P-4/#13 UBLK Setting-related Controls for ATPD & DCTR
P&P & Favorite
Single
UBLK = 0~7
22 23
ATPD DCTR
0~3 0~3
0 0
1 1
2 1
3 1
1 2
2 2
3 2
2 3
0 0
Note: The same CXA2103 service data (Main&Sub) is used for DX1A-2001&2000.
-- 23 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#2-2): CXA2103-2 {Sub}
Device Name: CXA2103Q { NTSC-YCT (Chroma Decoder) / SONY } / IC3110 (B-board) / P/N: 8-752-089-50 (SBorSD#: NA) Slave Address: 9Eh { Sub }
Register No & Name Control Register Function & Link Data Type Data Range Data Initial Setting & [Average Data]
(32V&36V CRTs) UHF/VHF & Video
P&P-Right (S) P&P-Right (S)-DRC
Data Initial/Average Setting
(32V&36V CRTs)
Note
0 1 2 3 4 5
YLEV CLEV SCON SCOL SHUE YDLY
Y-Out gain Cb&Cr-Out gains Sub contrast Sub color Sub hue Y/C delay time
SNNR Data-related Settings
0~63 0~63 Adj. Adj. Adj. 0~15 0~15 0~15 0~3 0~15 0~3 0~3 0~3 0~3 0, 1 0, 1 0, 1 0, 1 0~3 0~3 0, 1 0, 1 0~15
23 18
UHF/VHF
22 16
Video
Video: CVideo1~4 & SVideo1~3 Inputs P&P-Right (S)-DRC: If P&P-Left is 1080i/ 480p signal, the signal from the sub chroma decoder is switched to DRC path.
7 [7] 7 [7] 7 [Adj.-2steps] 0
UHF/VHF CVideo
7 [7] 7 [7] 7 [Adj.-2steps] 0
SVideo
Adj.: Adjusted data [Adj.-2steps]: The adjusted data - 2 steps
SNNR=0 (-offset)
SNNR=1 (-offset)
SNNR=2 (-offset)
SNNR=3 (-offset)
6 SHAP 7 SHF0 8 PREO 9 BPF0 10 BPFQ 11 BPSW 12 TRAP 13 LPF 14 AFCG 15 CDMD 16 SSMD 17 HMSK 18 HALI 19 PPHA
Sharpness Sharpness f0 selector Sharpness pre/over-shoot ratio Chroma band filter f0 setting Chroma band filter Q setting Chroma band filter on/off Y bolck chroma trap filter on/off YPbPr-Output LPF on/off AFC Loop Gain V countdown system mode selector H&Vsync slide level setting Masking of macrovision signal on/off H automatic adjustment on/off H TIM phase adjustment for video
6 0 3 0 0 0 0 0
UHF/VHF
4 0 0 0 0 0 0 0
Video
4 0 0 0 0 0 0 0
0
1
2
3
CVideo: CVideo1~4 Inputs SVideo: SVideo1~3 Inputs
1 3 0 1 0 7
P&P-Right (S)
0 3 0 1 0 7
YPbPr-480i
P&P-Right (S) P&P-Right (S)-DRC P&P-Right (S)-DRC
UHF/VHF & CVideo
20 CBOF 21 CROF
Cb-Offset1 of Cb IN (Pin34) Cb-Offset2 of EXT Cb (Pin38) Cr-Offset1 of Cr IN (Pin35) Cr-Offset2 of EXT Cr (Pin39) Auto-pedestal Inflection Point DC Transmission Ratio
0~(31)~63 0~(31)~63
31 31
UBLK = 0
31 31
UBLK = 1
31* 31*
UBLK = 2
31* 31*
UBLK = 3
*: Settings not used (31): The center setting = 31
P&P & Favorite
UBLK = 4 UBLK = 5 UBLK = 6 UBLK = 7
CXA2150P-4/#13 UBLK Setting-related Controls for ATPD & DCTR
P&P & Favorite
Single
UBLK = 0~7
22 23
ATPD DCTR
0~3 0~3
0 0
1 1
2 1
3 1
1 2
2 2
3 2
2 3
0 0
Note: The same CXA2103 service data (Main&Sub) is used for DX1A-2001&2000.
-- 24 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#3-1): CXA2150P-1 {Picture Controls: P1}
Device Name: CXA2150AQ { CRT Driver / SONY } / IC201 (A-board) / P/N: 8-752-093-35 (SBorSD#: NA) Slave Address: 86h
Register No & Name Control Register Function & Link Data Type Data Range
UHF VHF
Data Initial Settings & [Average Data]
(32V&36V CRTs) CV SV YPbPr 480i YPbPr 480p YPbPr 1080i P&P
Comment CV: CVideo1~4 SV: SVideo1~3 ( ): Settings at center Adj.: Adjusted data C: Common data Initial Setting = [Avg. Data]
0 1 2 3 4 5 6 7 8 9 10
SBOT YOF CBOF CROF SBRT RDRV GDRV BDRV RCUT GCUT BCUT
Offset for SBRT Y_OFFSET: DC-offset for Y signal CB_OFFSET: DC-offset for Cb signal CR_OFFSET: DC-offset for Cr signal SUB_BRIGHT: Sub Bright R_DRIVE: R output drive G_DRIVE: G output drive B_DRIVE: B output drive R_CUTOFF: R output cutoff G_CUTOFF: G output cutoff B_CUTOFF: B output cutoff
Adj. C Adj. Adj. C Adj. Adj.
0~(7)~15 0~(7)~15 0~(31)~63 0~(31)~63 0~63 0~63 0~63 0~63 0~63 0~63 0~63 0, 1 0~(63)~127 0~(63)~127 0~(63)~127 0~(63)~127 0~(63)~127 0~(63)~127 0~(63)~127
7 0 31 31
7 0 31 31
7 0 31 31
7 7 0 0 33 30 42 36 24 [24] 41 36 [36] 33 [33] 41 11 [11] 22 [22]
Movie
7 0 31 31
7 0 13 23
Vivid
Standard
Pro
WB_SW: White balance offset on/off 11 WBSW (Related to UTMP seetings) 12 SBOF Offset for SBRT 13 RDOF Offset for RDRV 14 GDOF Offset for GDRV 15 BDOF Offset for BDRV 16 RCOF Offset for RCUT 17 GCOF Offset for GCUT 18 BCOF Offset for BCUT
Note: The same CXA2150 service data is used for DX1A-2001&2000.
0
(Cool)
0
(Neutral)
1
(Warm)
0 63 63 63 63 63 63 63
63 63 63 63 63 63 63
63 63 63 63 63 63 63
63 63** 66** 76** 63** 66** 78**
**: The color temporature offset data
-- 25 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#3-2): CXA2150P-2 {Picture Controls: P2}
Device Name: CXA2150AQ { CRT Driver / SONY } / IC201 (A-board) / P/N: 8-752-093-35 (SBorSD#: NA) Slave Address: 86h
Register No & Name Control Register Function & Link Data Type Data Range Data Initial/Average Settings
(32V&36V CRTs)
Comment
0 1 2 3 4 5 6 7 8 9 10 11 12
ALBK RGBS BLKB LIML PABL SABL AGNG AKBO SYPH CLPH CLGA JAXS BLKO
PIC_ON: RGB output including AKB reference pulse on/off (Setting = 0 for power on reset) --- G2 adjustment register setting R_ON/G_ON/B_ON: R/G/B outputs on/off (AKB reference pusle can not be turned on/off.) (0,1/0,1/0,1) BLK_BTM: RGB output bottom limit level (Black Limit) (AKB reference pusle DC-voltage) PLIMIT_LEV: Threshold level for excessively high inputs (White Limit) P_ABL: DC-level in RGB output detection for PEAK ABL S_ABL: S_ABL gain AGING_W/AGING_B: AGING_W/AGING_B modes on/off (Set luminance to 80/01IRE flat-field signal.) AKBOFF: Automatic/Manual-Cutoff setting SYNC_PHASE: Hsync delay with respect to Video (100%: H-period) CLP_PHASE: Internal clamp pulse phase (100%: H-period) CLP_GATE: Switch for the gated internal clamp pulse with Hsync input JAXIS: Color axis switch BLKO: Blanking switch
C C C C C C C C
0, 1 0~7 0~3 0~3 0~15 0~3 0~3 (0,1/0,1) 0, 1 0~3 0~3 0, 1 0, 1 0, 1
1 7 3 0 15 0 0 0
U/VHF & Video1~4 YPbPr 480i YPbPr 480p YPbPr 1080i P&P
C: Common data
0 3 0 0 0
0 3 0
0 3 0
0 3 0
0 3 0
Video1~4: CVideo1~4 & SVideo1~3
Note: The same CXA2150 service data is used for DX1A-2001&2000.
-- 26 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#3-3): CXA2150P-3 {Picture Controls: P3} (Part-1/3)
Device Name: CXA2150AQ { CRT Driver / SONY } / IC201 (A-board) / P/N: 8-752-093-35 (SBorSD#: NA) Slave Address: 86h
Data Initial/Average Settings (32V&36V CRTs) Register No & Name Control Register Function & Link Data Type Data Range
Picture Mode: Vivid
UHF VHF CV SV YPbPr 480i YPbPr 480p YPbPr 1080i P&P
Comment
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
SYSM UVML VMMO VMCR VMLM VMF0 VMDL SHOF SHF0 PROV F1LV CDSP LTLV LTMD CTLV CTMD UBOF UCOF UHOF MIDE
SYSTEM: Signal bandwidth setting C VM_LEV: VM_OUT level System Micro pin#40 VM_COR: VM_OUT coring level VM_LMT: VM_OUT limit level VM_F0: VM_f0 VM_DLY: VM_OUT phase (defined by phase difference from R_OUT) Offset for USHP = SHOF x 4 SHP_F0: Sharpness circuit f0 PRE/OVER: Y signal pre/over-shoot ratio SHP_F1: Sharpness for higher f0 (4.2/5.6 MHz @ NORMAL mode) SHP_CD: Sharpness in part of high color saturaion LTI_LEV: Luminance transient improvement (LTI) LTI_MODE: LTI mode setting CTI_LEV: Chrominance transient improvement (CTI) CTI_MODE: CTI mode setting Offset for UBRT (Picture clarity adjustment) Offset for UCOL = UCOF x 2 (Picture clarity adjustment) Offset for UHUE (Picture clarity adjustment) MID enhancement setting
0~3 0~3 0, 1 0~3 0~3 0~3 0~3 0~3 0, 1 0~3 0~3 0~3 0~3 0~3 0~3 0~3 0~(7)~15 0~3 0~3 0~15
1 3 0 3 3 2 3 2 1 3 0 3 3 0 0 0 7 3 0 3
1 0 3 3 2 3 2 1 3 3 3 3 0 0 0 7 3 0 3
1 0 3 3 2 3 2 1 3 3 3 3 0 0 0 7 3 0 3
1 0 3 3 2 3 3 1 1 3 3 3 0 0 0 7 3 0 7
1 0 3 3 2 3 3 1 3 3 3 3 0 0 0 7 3 0 11
2 0 3 3 2 1 0 0 0 3 3 3 0 2 0 10 0 0 ---
2 0 3 3 2 3 2 1 3 3 3 3 1 0 0 7 3 0 ---
These settings continue to the next page. CV: CVideo1~4 SV: SVideo1~3 C: Common data ( ): Settings at center
Note: The same CXA2150 service data are used for DX1A-2001&2000.
-- 27 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#3-3): CXA2150P-3 {Picture Controls: P3} (Part-2/3)
Data Initial/Average Settings (32V&36V CRTs) Register No & Name
Picture Mode: Standard
UHF VHF CV SV YPbPr 480i YPbPr 480p YPbPr 1080i P&P
Data Initial/Average Settings (32V&36V CRTs)
Picture Mode: Movie
UHF VHF CV SV YPbPr 480i YPbPr 480p YPbPr 1080i P&P
Data Initial/Average Settings (32V&36V CRTs)
Picture Mode: Pro
UHF VHF CV SV YPbPr 480i YPbPr 480p YPbPr 1080i P&P
Note
#0 SYSM (cont.) #1 UVML (cont.) #2 VMMO (cont.) #3 VMCR (cont.) #4 VMLM (cont.) #5 VMF0 (cont.) #6 VMDL (cont.) #7 SHOF (cont.) #8 SHF0 (cont.) #9 PROV (cont.) #10 F1LV (cont.) #11 CDSP (cont.) #12 LTLV (cont.) #13 LTMD (cont.) #14 CTLV (cont.) #15 CTMD (cont.) #16 UBOF (cont.) #17 UCOF (cont.) #18 UHOF (cont.) #19 MIDE (cont.)
1 3 0 3 3 2 1 0 0 3 0 3 2 1 0 0 7 3 0 2
1 0 3 3 2 3 3 1 3 3 3 2 1 0 0 7 3 0 2
1 0 3 3 2 3 3 1 3 3 3 2 1 0 0 7 3 0 2
1 0 3 3 2 3 3 1 1 3 3 2 1 0 0 7 3 0 6
1 0 3 3 2 3 3 1 3 3 3 2 1 0 0 7 3 0 10
2 0 3 3 2 1 0 0 0 3 3 2 1 2 0 7 0 0 ---
2 0 3 3 2 3 2 1 3 3 3 3 1 0 0 7 3 0 ---
1 0 0 3 3 2 1 0 0 3 0 0 0 1 0 0 7 0 0 1
1 0 3 3 2 1 3 0 3 0 0 0 1 0 0 7 0 0 1
1 0 3 3 2 1 3 0 3 0 0 0 1 0 0 7 0 0 1
1 0 3 3 2 1 3 0 1 0 0 0 1 0 0 7 0 0 5
1 0 3 3 2 1 3 0 3 0 0 0 0 0 0 7 0 0 9
2 0 3 3 2 1 0 0 0 0 0 0 0 0 0 7 0 0 ---
2 0 3 3 2 3 3 1 3 3 0 0 1 0 0 7 0 0 ---
1 0 0 3 3 2 1 0 0 3 0 0 0 1 0 0 7 0 0 0
1 0 3 3 2 1 1 0 3 0 0 0 1 0 0 7 0 0 0
1 0 3 3 2 1 1 0 3 0 0 0 1 0 0 7 0 0 0
1 0 3 3 2 1 1 0 1 0 0 0 1 0 0 7 0 0 4
1 0 3 3 2 1 1 0 3 0 0 0 0 0 0 7 0 0 8
2 0 3 3 2 1 0 0 0 0 0 0 0 0 0 7 0 0 ---
2 0 3 3 2 3 1 1 3 3 0 0 1 0 0 7 0 0 ---
See next page
Note: The same CXA2150 service data are used for DX1A-2001&2000.
DX1A-2001&2000 SERVICE LIST (#3-3): CXA2150P-3 {Picture Controls: P3} (Part-3/3)
Data Initial/Average Settings (32V&36V CRTs) Register No & Name
SNNR=0 (Offset) SNNR=1 (Offset) SNNR=2 (Offset) SNNR=3 (Offset)
Comment
#1 UVML (cont.) #3 VMCR (cont.) #10 F1LV (cont.) #11 CDSP (cont.) #12 LTLV (cont.) #14 CTLV (cont.) #19 MIDE (cont.)
0 0 0 0 0 0 0
0 +1 -1 0 0 0 0
0 +2 -2 0 0 0 0
0 +3 -3 0 0 0 0
Note: The same CXA2150 service data are used for DX1A-2001&2000.
-- 28 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#3-4): CXA2150P-4 {Picture Controls: P4} (Part-1/4)
Device Name: Device Name:
Register No & Name
CXA2150AQ { CRT Driver / SONY } / IC201 (A-board) / P/N: 8-752-093-35 (SBorSD#: NA) Slave Address: 86h CXD2085M { ID-1 Decoder / SONY } / IC3603 (B-board) / P/N: 8-752-395-13 (SD#: S98511B) Slave Address: 40h
Control Register Function & Link Data Type Data Range
Vivid
32V 36V
Data Initial/Average Settings
(32V&36V CRTs) Standard
32V 36V
Comment
Pro
Movie
32&36V
0 1 2 3 4 5 6
UPIC UBRT UCOL UHUE USHP UTMP UDCL
PICTURE: Picture BRIGHT: Brightness COLOR: Color HUE: Hue
SNNR Setting-related Controls for USHP
0~63 0~63 0~63 0~63 0~63 0~2 0~3
63 25 34 31 38 2 2
63 22 38 31 42 2 2
42 28 33 31 44 1 2
YPbPr 480i
46 26 33 31 48 1 2
YPbPr 480p YPbPr 1080i
31 28 33 31 34 0 2
P&P
31 31 31 31 31 1 0
Settings for 36V CRTs are used for initial settings. This setting continues to the next page.
SHARPNESS: Sharpness Color Temporature (0: Warm, 1: Neutral, 2: Cool) DCOL: Dynamic color setting
Picture Mode: Vivid / Standard / Movie
UHF/VHF Video1~4
7
AXIS
COL_AXIS: Color matrix setting
0~3
3
UHF/VHF Video1~4
3
YPbPr 480i
3
YPbPr 480p
3
YPbPr 1080i
3
P&P
These settings continue to the next page. Video1~4: CVideo1~4 & SVideo1~3
Picture Mode: Vivid
8 9
UGAM
GAMMA/GAMMA_L: RGB output GAMMA correction setting (B 7~6) GAMMA_L: Slight GAMMA correction on/off (B 0)
AGAM GAMMA/GAMMA_L (Av Pro user control) --- Void Data
UGAM Setting-related Controls for GSBO, GCOO, GHUO
0~7 (0~3/0,1) 0~7 (0~3/0,1) 0~3 0~3 0~3
5 --UGAM =7 UGAM =6
5
5
5
5
UGAM =5
UGAM =4
UGAM =3
UGAM =2
UGAM =1
10 GSBO 11 GCOO 12 GHUO
Offset for SBRT (8 types of GSBO data based on UGAM values) Offset for UCOL Offset for UHUE
0 0 0
0 0 0
0 0 0
YPbPr 480i
0 0 0
YPbPr 480p
0 0 0
YPbPr 1080i
0 0 0
P&P
0 0 0
Picture Mode: Vivid
UHF/VHF Video1~4
These settings continue to the next page.
13 UBLK 14 ABLK 15 DCTR 16 DPIC 17 DSBO 18 ABLM
Item # 15~18 pack FI data controls (Av Pro user control) --- Void Data
UBLK Setting-related Controls for DCTR
---
0~7 0~7 0~3 0~3 0~(7)~15 0~3
7 0 (Void data) 3 2 7 1
7
7
7
7
DC_TRAN: Y signal DC transmission (8 types of DCTR data based on UBLK values) DPIC_LEV: Y signal AUTO PEDESTAL level Offset for SBRT ABL_MODE: ABL mode
3 2 7 1
3 2 7 1
3 2 7 1
2 1 7 1
These settings continue to the next page. ( ): Seetings at center
Note: The same CXA2150 service data are used for DX1A-2001&2000.
-- 29 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#3-4): CXA2150P-4 {Picture Controls: P4} (Part-2/4)
Register No & Name
Data Initial/Average Settings
(32V&36V CRTs)
Data Initial/Average Settings
(32V&36V CRTs)
Data Initial/Average Settings
(32V&36V CRTs)
Note
SNNR Setting (-Offset)
SNNR =0
SNNR =1
SNNR =2
SNNR =3
#4 USHP (cont.)
0
1
3
4
Picture Mode: Pro
UHF/VHF Video1~4 YPbPr 480i YPbPr 480p YPbPr 1080i P&P
#7 AXIS (Cont.)
3
U/VHF Video1~4
3
YPbPr 480i
3
YPbPr 480p
3
YPbPr 1080i
3
Picture Mode: Movie
P&P U/VHF Video1~4 YPbPr 480i YPbPr 480p YPbPr 1080i P&P U/VHF Video1~4
Picture Mode: Standard
Picture Mode: Pro
YPbPr 480i YPbPr 480p YPbPr 1080i P&P
#8 UGAM (Cont.)
2
2
2
2
2
0
0
0
0
0
0
0
0
0
0
UGAM
=0
#10 GSBO (cont.) #11 GCOO (cont.) #12 GHUO (cont.)
0 0 0
Picture Mode: Standard
UHF/VHF Video1~4 YPbPr 480i YPbPr 480p YPbPr 1080i P&P UHF/VHF Video1~4
Picture Mode: Movie
YPbPr 480i YPbPr 480p YPbPr 1080i P&P UHF/VHF Video1~4
Picture Mode: Pro
YPbPr 480i YPbPr 480p YPbPr 1080i P&P
#13 UBLK (Cont.)
4
4
4
4
4
1
1
1
1
1
0
0
0
0
0
#15 DCTR (Cont.) #16 DPIC (Cont.) #17 DSBO (Cont.) #18 ABLM (Cont.)
2 1 7 1
2 1 7 1
2 1 7 1
2 1 7 1
2 1 7 1
1 1 7 0
1 1 7 0
1 1 7 0
1 1 7 0
1 1 7 0
1 0 7 0
1 0 7 0
1 0 7 0
1 0 7 0
1 0 7 0
See next pages
Note: The same CXA2150 service data are used for DX1A-2001&2000.
-- 30 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#3-4): CXA2150P-4 {Picture Controls: P4} (Part-3/4)
Register No & Name
UBLK = 7 UBLK = 6
Data Initial/Average Settings
(32V&36V CRTs) UBLK = 5 UBLK = 4 UBLK = 3 UBLK = 2 UBLK = 1 UBLK = 0
Comment
#15 DCTR (Cont.) #16 DPIC (Cont.) #17 DSBO (Cont.) #18 ABLM (Cont.)
3 2 7 1
2 3 7 0
2 2 7 0
2 1 7 1
1 3 7 0
1 2 7 0
1 1 7 0
1 0 7 0
Note: The same CXA2150 service data are used for DX1A-2001&2000.
DX1A-2001&2000 SERVICE LIST (#3-4): CXA2150P-4 {Picture Controls: P4} (Part-4/4)
Register No & Name
Control Register Function & Link
Data Type
Data Range
Data Initial/Average Settings
(32V&36V CRTs)
Comment
19
ABLT
ABL_TH: ABL currect detection Vth control Control of CXA2026 {0Ch -- DAC0} (*) Offset for UPIC = EPOF x (UPIC/63) (for power save) --- Void Data
ID-1 and P&P Modes
0~15 0~255 0~31 0~31 0~15 0~(7)~15 0~7~15 C C 0, 1 0~3 0
0
Full Vcomp1 Vcomp2
20 ABLC 21 EPOF 22 SPOF 23 SCON 24 CLOF 25 HUOF 26 27 IDSW DATA
0
66
-----
Offset for UPIC = SPOF x (UPIC/64) --- Data Not Used SUB_CONTRAST: SUB PICTURE Offset for UCOL Offset for UHUE
CXD2085 Service Controls
0 (Not used)
UHF/VHF Video1~4
YPbPr 480i YPbPr 480p YPbPr 1080i P&P
9 8 4
8 8 3
11 9 3
10 7 3
9 8 4
Full: 480p/960i (4x3) Vcomp1: 480p/960i (16x9) Vcomp2: 1080i (16x9) ( ): Settings at center C: Common data
Switch for activating the selection in #27 DATA Selection of geometry-forced vertical compression modes
Full
Vcomp1
Vcomp2
0
1
2
Note: The same CXA2150 service data are used for DX1A-2001&2000.
-- 31 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#4-1): CXA2150D-1 {Deflection Controls: D1}
Device Name: CXA2150AQ { CRT Driver / SONY } / IC201 (A-board) / P/N: 8-752-093-35 (SBorSD#: NA) Slave Address: 86h
Register No & Name Control Register Function & Link Data Type Data Range Data Initial Settings & [Average Data] (32V&36V CRTs)
Full Vcomp1 Vcomp2
Comment Full: 480p/960i (4x3) display Vcomp1: 480p/960i (16x9) display Vcomp2: 1080i (16x9) display Adj.: Adjusted data ( ): Settings at center VCEN-L(Low bit) VCEN-H(High bit) [Copy1]: Copy the adjusted data for Full mode. Either 7 or 8 can be used as the average NSCO data. (If both of them are not good, please feedback to / check with the DY attachment process.)
0 1 2 3 4 5 6
VPOS VSIZ VLIN VSCO VCEN VPIN NSCO
V_POSITION: Vertical position (V_DRV siganl DC-bias) V_SIZE: Vertical size (V_DRV signal gain) V_LINEARITY: Vertical linearity (Gain for V_DRV signal secondary component) S_CORRECTION: Vertical S-correction VSAW0_DCH/VSAW0_DCL: Vertical center adjustment VSAW0_DCH: VSAW0 waveform DC component (high 2-bits) VSAW0_DCL: VSAW0 waveform DC component (low 4-bits) VSAW0_AMP: Vertical PIN adjustment VSAW0 waveform SAW component amplitude VSAW1_DC: Rotation VSAW1_AMP: Horizontal trapezoid ZOOM_SW: Zoom switch ASP_SW: Aspect switch V_ASPECT: Aspect ratio V_SCROLL: Vertical scroll UP_VLIN: Upper vertical linearity LO_VLIN: Lower vertical linearity
Adj. 0~(31)~63 Adj. 0~(31)~63 Adj. Adj. 0~(7)~15 0~(7)~15
26 [26] 19 [19] 9 [9] 8 [8] 31 [31] 15 [15] 15 [Copty1] 7 [7] 15 [15] 0 1 47 31 0 0 0 1 47 32 0 0 0 47 32
Adj. 0~(31)~63 Adj. 0~(15)~31 Adj. 0~(7)~15
7 HTPZ 8 ZOOM 9 APSW 10 ASPT 11 SCRL 12 UVLN 13 LVLN
Adj. 0~(15)~31 0, 1 0, 1 Adj. 0~63 Adj. 0~(31)~63 0~15 0~15
Note: The same CXA2150 service data is used for DX1A-2001&2000.
-- 32 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#4-2): CXA2150D-2 {Deflection Controls: D2}
Device Name: CXA2150AQ { CRT Driver / SONY } / IC201 (A-board) / P/N: 8-752-093-35 (SBorSD#: NA) Slave Address: 86h
Register No & Name Control Register Function & Link Data Type Data Range Data Initial Settings & [Average Data]
(32V&36V CRTs) Full Vcomp1 Vcomp2
Comment Full: 480p/960i (4x3) display Vcomp1: 480p/960i (16x9) display Vcomp2: 1080i (16x9) display ( ): Settings at center Adj.: Adjusted data [Adj.-6steps]: The adj. data for Vcomp2 mode = The adj. data for Full/Vcomp1 modes - 6 steps Data (32Vor36V): The data for 36V are used as the Initial & CBA data. From the system micro (V 2.0), the deflection control-related initial settings are the same as their average data.
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
HCNT HPOS HSIZ SLIN MPIN PIN UCP LCP UXCG LXCG UXCP LXCP XCPP PPHA VANG LANG VBOW LBOW CPY1
HC_PARA_DC: Horizontal center H_POSITION: Horizontal position H_SIZE: Horizontal size MP_PARA_DC: Horizontal S-correction MP_PARA_AMP: Horizontal middle pin PIN_AMP: Horizontal pin UP_CPIN: Upper corner pin LO_CPIN: Lower corner pin UP_UCG: Upper extra corner pin gain LO_UCG: Lower extra corner pin gain UP_UCP: Upper extra corner pin position LO_UCP: Lower extra corner pin postion UC_POL: Extra corner pin polarity PIN_PHASE: Pin phase AFC_ANGLE: AFC angle HC_PARA_PHASE: Linearity angle AFC_BOW: AFC bow HC_PARA_AMP: Linearity bow Copy Function 1: (Set CPY1=1, then press MUTE + Enter.) Copy all CXA2150D-2 data for Full mode to Vcomp1&2
Adj. 0~(31)~63 Adj. 0~(31)~63 Adj. 0~(31)~63 Adj. 0~15 0~15 Adj. 0~(31)~63 Adj. 0~(31)~63 Adj. 0~(31)~63 0~3 0~3 0~3 0~3 0, 1 Adj. 0~(31)~63 Adj. 0~(31)~63 Adj. 0~(31)~63 Adj. 0~(31)~63 Adj. 0~(31)~63
Micro
31 [31] 31 [31] 45 [45] 3 [3] 9 (32V) or 7 (36V) 35 [35] 38 [38] 42 [42] 2 (32V) or 1 (36V) 2 2 2 0 15 [15] 31 [31] 31 [31] 31 [31] 31 [31] 0 31 [Adj.-6steps]
0, 1
For engineering design use only
Note: The same CXA2150 service data is used for DX1A-2001&2000.
-- 33 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#4-3): CXA2150D-3 {Deflection Controls: D3}
Device Name: CXA2150AQ { CRT Driver / SONY } / IC201 (A-board) / P/N: 8-752-093-35 (SBorSD#: NA) Slave Address: 86h
Register No & Name Control Register Function & Link Data Type Data Range
Full
Data Initial/Average Settings
(32V&36V CRTs) Vcomp1 Vcomp2
Comment Full: 480p/960i (4x3) display Vcomp1: 480p/960i (16x9) display Vcomp2: 1080i (16x9) display
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
HBLK LBLK RBLK VBLK TBLK BBLK VCMP HCMP ACMP PCMP AFCM VFRQ VON JUMP VDJP VDST EWDC AKBT
HBLK_SW: Horizontal blanking switch LEFT_BLK: Left blanking RIGHT_BLK: Right blanking VBLK_SW: Vertical blanking switch UP_BLK: Top blanking LO_BLK: Bottom blanking V_COMP: Vertical compensation H_COMP: Horizontal compensation AFC_COMP: AFC compensation PIN_COMP: Pin compensation AFC_MODE: AFC loop gain V_FREQ: Vertical frequency V_ON: Vertical drive on JMP_SW: Reference pulse jump swtich VDRV_SW: Vertical drive jump switch RST_SW: Vertical drive start switch EW_DC: Pin DC level shift AKBTIM: AKB timing
0, 1 0~63 0~63 0, 1 0~(7)~15 0~(7)~15 0~15 0~15 0~7 0~7 0~3 0~3 0, 1 0, 1 0, 1 0, 1 0, 1 0~31
1 45 24 1 1 0 0 0 0 0 3 1 1 0 0 0 0 20 1 0 0 0 20 10 1 1 1 8 13 0 0 0 0 2 12 13 0 50 27
( ): Settings at center
Note: The same CXA2150 service data is used for DX1A-2001&2000.
-- 34 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#5): CXA2151Q
Device Name: CXA2151Q { Component I/F & Sync Seperation / SONY } / IC3001 (B-board) / P/N: 8-752-093-84 (SD#: S00302B) Slave Address: 84h
Register No & Name Control Register Function & Link Data Type Data Range Data Initial/Average Settings (32V&36V CRTs)
480i (15.75 KHz) 480p (31.50 KHz) 1080i (33.75 KHz)
Comment Video5&6: YPbPr-480i/480p/1080i inputs Sub: 480i input from the sub-channel Full: 480p/960i (4x3) display Vcomp1: 480p/960i (16x9) display Vcomp2: 1080i (16x9) display C: Common data
0 1 2 3 4 5 6 7 8
MTRX GAIN CBGN VTC HWID HSEP TEST FRGB HMSK
MAT_OUT: Selection of color matrix conversion types GAIN_SEL: Selection of output signals for SELYOUT, SELCBOUT, SELCROUT YGAIN, CBGAIN, CRGAIN: The gain control of SELYOUT, SELCBOUT, & SELCROUT V_TC: Setting of Vsync separation time constant H_WIDTH: Setting of the output pulsewidth of SELHOUT HSEP_SEL: Setting for the sync separation system TEST: Test mode selection (for device tests) The forced RGB selection (for tests) {0: MAT_OUT = MTRX (#0), 1: MAT_OUT = MTRX (#3)} Hsync masking in vertical retrace
Micro
0~3 0~3 0~15 0~3 0~3 0, 1 0, 1 0, 1 0, 1
0 0 9 1 1
Video5
0
1
C C C C
Video6
Sub
C C
0 0 0
Full
0
0
Vcomp1
Vcomp2
1
0
Note: The same CXA2151 service data is used for DX1A-2001&2000.
-- 35 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#6): D-CONV / CXA8070
Device Name: CXA8070AP { DY-Convergence Control / SONY } / IC5513 (D-board) / P/N: 8-759-595-52 (SB#: V1718) Slave Address: DEh
Register No & Name Control Register Function & Link Data Type Data Range Data Initial Settings & [Average Data] (32V&36V CRTs)
Full Vcomp1 Vcomp2
Comment
0 1 2 3 4 5 6 7 8 9 10
SBHS YBWU YBWL RSAP RUBW RLBW LSAP LUBW LLBW CADJ CPY2
DC AMP3: DC shift VCA9: Upper Y-bow VCA10: Lower Y-bow DC AMP2: Right H-AMP VCA5: Right upper bow VCA6: Right lower bow DC AMP1: Left H-AMP VCA1: Left upper bow VCA2: Left lower bow DC AMP4: Offset adjustment (ADJ) Copy Function 2: (Set CPY2=1, then press MUTE + Enter.)
Adj. Adj. Adj. Adj. Adj. Adj. Adj. Adj. Adj. Adj.
Micro
0~63 0~63 0~63 0~63 0~63 0~63 0~63 0~63 0~63 0~63 0, 1
31 31 31 31 31 31 31 31 31
[31] [31] [31] [31] [31] [31] [31] [31] [31]
31 31 31 31 31 31 31 31 31 48 [48] 0
[31] [31] [31] [31] [31] [31] [31] [31] [31]
Full: 480p/960i (4x3) display mode Vcomp1: 480p/960i (16x9) display mode Vcomp2: 1080i (16x9) display mode Adj.: Adjusted data From the system micro (V 2.0), the deflection control-related initial settings are the same as their average data.
For engineering design use only
Note: The same CXA8070 service data is used for DX1A-2001&2000.
-- 36 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#7): CXA2026AS
Device Name: CXA2026AS { DQP Control / SONY } / IC5511 (D-board) / P/N: 8-752-074-64 (SD#: S95610B) Slave Address: 8Eh
Register No & Name Control Register Function & Link Data Type Data Range Data Initial Settings & [Average Data]
(32V&36V CRTs) Full Vcomp1 Vcomp2
Comment Full: 480p/960i (4x3) display mode Vcomp1: 480p/960i (16x9) display mode Vcomp2: 1080i (16x9) display mode C: Common data Adj.: Adjusted data U.CBOW = QPDV + DVS L.CBOW = QPDV - DVS ( ): Settings at center Data (36V) are used as Initial/CBA data. From the system micro (V 2.0), most deflection control-related initial settings are the same as their average data. U.YBOW = QPAV + AVS L.YBOW = QPAV - AVS
0 1 2 3 4 5 6 7
DFON DQP DF DQPD QPDV DVS QPDY DQPA
SW0: DF on/off switch PWM: DQP phase DAC1: DF phase H.AMP: DQP dc-level U.CBOW, L.CBOW: DQP dc-level vertical modulation U.CBOW, L.CBOW: DQP dc-level tilt U.MBH,L.MBH: DQP dc-level at top & bottom areas DC SHIFT: DQP amplitude U.YBOW, LYBOW: DQP amplitude vertical modulation U.YBOW, LYBOW: DQP amplitude tilt SW1: Copy Function 3: (Set CPY3=1, then press MUTE + Enter.) H.DUTY, H.TILT: 200V regulator adjustment
C Adj. Adj. Adj.
0, 1 0~63 0~63 0~63 0~63 0~(3)~7 0~63 0~63 0~63 0~7 0, 1
Adj.
8 QPAV 9 AVS 10 NORM 11 12 CPY3 200V
0 23 [23] 23 [23] 25 [25] 25 [25] 34 [34] 34 [34] 51 47 0 0 7 7 22 [27] (32V) 22 [27] (32V) 22 [27] or or or 13 [15] (36V) 13 [15] (36V) 13 [15] 38 34 3 3 0 0 0 31 [31]
(32V)
(36V)
Micro
0, 1 0~63
For engineering design use only
Adj.
Note: The same CXA2026 service data is used for DX1A-2001&2000.
-- 37 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#8): Audio Processing (AP) / BH3868AFS
Device Name: BH3868AFS { Audio Processor / ROHM } / IC7001 (A-board) / P/N: 8-759-678-92 (SBorSD#: NA) Slave Address: 82h
Register No & Name Control Register Function & Link Data Type Data Range Data Initial/Average Setting
(32V&36V CRTs)
Comment
0 1 2 3 4 5 6 7 8
SVOL SBAL SBAS STRE BBLP BBHP SREF AGC BBE
Volume: Offset for Volume Balance: Offset for Balance Bass: Offset for Bass Treble: Offset for Treble BBE lowpass filter BBE highpass filter Surround effect Auto gain control BBE on/off
0~3 0~(3)~7 0~(3)~7 0~(3)~7 0~15 0~15 0~7 0, 1 0, 1
0 7 7 7 0 2 11 0 1
( ): Settings at center
Note: The same AP service data is used for DX1A-2001&2000.
DX1A-2001&2000 SERVICE LIST (#9): TruSurround (TRUS) / NJM2180
Device Name: NJM2180M { TruSurround 3D-Audio Processor / JRC } / IC4101 (S-board) / P/N: 8-759-686-15 (SB#: V9072) Device Control: Controlled via CXA1315M (Audio Control D/A, IC4103/S-board, Slave Address: 48h) / P/N: 8-752-059-23 (SD#: S88Z45B)
Register No & Name Control Register Function & Link Data Type Data Range Data Initial/Average Setting
(32V&36V CRTs)
Comment C: Common data DMY1 is used to fulfil the minimum requirement of 2 control items in each service control category.
0 1
TS DMY1
TruSurround effect selection Dummy data (No functions) C
0~3 0~255
2 0
Note: The same TRUS service data is used for DX1A-2001&2000.
-- 38 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001* SERVICE LIST (#10): MID1 (Common Data)
Device Name: CXD9509AQ { MID-XA / Fujitsu & SONY } / IC3408 (B-board) / P/N: 8-759-672-57 (SBorSD#: NA) Slave Address: 2Eh { Controlled through MID-XA Micro (IC3090/B-board, Slave Address: 64h) / P/N: 6-800-050-01 (SB#: V4216) } MID-XA Micro (MASK type): MB94918RPF-G-137-BND, MID-XA Software: Version 12/08/00, (P/N: 6-800-050-01)
Register No & Name Control Register Function & Link Register Name (Software) Data Type Data Range Data Initial/Average Setting
(32V/36V/40V CRTs) MID Mode: All (Single & P&P & Favorite)
Comment
0 1 2 3 4 5 6 7
DHPH DVPH DHAR DVAR DHPW DVPW DYCD DYSD
Horizontal phase of the active display area d_h_phase Vertical phase of the active display area d_v_phase Horizontal size of the active display area d_h_area Vertical size of the active display area d_v_area Horizontal pulse width d_h_pwidth Vertical pulse width d_v_pwidth Delay of YC signal output d_yc_delay Delay of YS signal output d_ys_delay
C C C C C C C C
0~255 0~63 0~255 0~255 0~63 0~7 0~63 0~7
Single 480i&p
91 20 240 135 27 7 2 1
MID Mode: Signle & Favorite
Single 1080i Favorite
C: Common data
8 9 10 11
MDHP MDVP MDHS MDVS
Horizontal position of the main picture Vertical position of the main picture Horizontal size of the main picture Vertical size of the main picture
m_dsp_hpos m_dsp_vpos m_dsp_hsiz m_dsp_vsiz
0~255 0~255 0~255 0~255 0~255 0~255
33 32 230 120 135 54 31
MID Mode: Favorite
8
12 14 158 106
MID Mode: P&P & Favorite
12 MLHP (Horizontal position of the multi pictures) 13 MLVP (Vertical position of the multi pictures) 14 15 16 17 SDHP SDVP SDHS SDVS Horizontal position of the sub picture Vertical position of the sub picture Horizontal size of the sub picture Vertical size of the sub picture s_dsp_hpos s_dsp_vpos s_dsp_hsiz s_dsp_vsiz dsp_pll_sw C C
0~255 0~255 0~255 0~255 0, 1 0, 1
172 14 61 41
MID Mode: All (Single & P&P & Favorite)
18 DPSW Switch of display output PLL 19 MDL0 Model selection 0 (0: 16x9, 1: 4x3)
0 0
0: MUST be used in DX1A-2001, 1: Used in DX1A-2000
Note: * These MID1 settings are used for DX1A-2001 ONLY. The DPSW setting was changed from 1 in DX1A-2000 to 0 in DX1A-2001.
-- 39 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#11): MID2 (DRC-in Data)
Device Name: CXD9509AQ { MID-XA / Fujitsu & SONY } / IC3408 (B-board) / P/N: 8-759-672-57 (SBorSD#: NA) Slave Address: 2Eh { Controlled through MID-XA Micro (IC3090/B-board, Slave Address: 64h) / P/N: 6-800-050-01 (SB#: V4216) } MID-XA Micro (MASK type): MB94918RPF-G-137-BND, MID-XA Software: Version 12/08/00, (P/N: 6-800-050-01)
Register No & Name Control Register Function & Link Register Name (Software) Data Type Data Range
MID Mode: Single
YC 480i YPbPr 480i
Data Initial/Average Setting
(32V&36V CRTs) MID Mode: P&P & Favorite
YC 480i YPbPr 480i YC 480i-(R)
MID Mode: Freeze
YC 480i YPbPr 480i
0 1 2 3
DRHP DRHS DRVP DRVS
Horizontal position of the active display area (DRC-in Hsize of the active display area (DRC-in) Vposition of the active display area (DRC-in) Vertical size of the active display area (DRC-in)
drc_hactv_pos drc_hactv_siz drc_vactv_pos drc_vactv_siz
0~255 0~255 0~63 0~255
120 174 38 120
116 174 38 120
131 167 53 112
129 167 53 112
137 168 53 112
138 165 53 112
136 165 53 112
Note: The same MID2 service data is used for DX1A-2001&2000.
DX1A-2001&2000 SERVICE LIST (#12): MID3 (VDO-in Data) (Part-1/2)
Device Name: CXD9509AQ { MID-XA / Fujitsu & SONY } / IC3408 (B-board) / P/N: 8-759-672-57 (SBorSD#: NA) Slave Address: 2Eh { Controlled through MID-XA Micro (IC3090/B-board, Slave Address: 64h) / P/N: 6-800-050-01 (SB#: V4216) } MID-XA Micro (MASK type): MB94918RPF-G-137-BND, MID-XA Software: Version 12/08/00, (P/N: 6-800-050-01)
Register No & Name Control Register Function & Link Register Name (Software) Data Type Data Range Data Initial/Average Setting
(32V&36V CRTs) MID Mode: Single
YPbPr 480P Dummy 480i
Comment
0 1 2 3 4 5 6 7 8 9 10
VDHP VDHS VDVE VDVS VDVO VCPO VCWD VYCD VSTP VSTT VHSC
Horizontal position of the active display area (VDO-in) Horizontal pixel size of the active display area (VDO-in) Vertical even position of the active display area (VDO-in) Vertical line size of the active display area (VDO-in) Vertical odd position of the active display area (VDO-in) Clamp pulse output timing (VDO-in) Clamp pulse width (VDO-in) Analog input YC delay (VDO-in) PD stop line count of external PLL (VDO-in) PD start line count of external PLL (VDO-in) Horizontal sync cycle (VDO-in)
vdo_hactv_pos vdo_hactv_pos vdo_vactv_evn vdo_vactv_pos vdo_vactv_odd vdo_clp_pos vdo_clp_wdt vdo_yc_delay vdo_pll_stop vdo_pll_strt vdo_hsync_cyc
0~255 0~255 0~63 0~255
YC 480i
122 159 39 129
YPbPr 480P YPbPr 1080i
179 199 24 56
Dummy 480i
Dummy-480i settings are used for No Signal cases. These settings continue to the next page.
0~3 0~255 0~7 0~63 0~255 0~15 0~255
0 95 3 0
0 70 3 0
YPbPr 480P
0 40 3 0
YPbPr 1080i
0 90 3 0
119 7 130
160 0
MID Mode: All (Single & P&P & Favorite)
Note: The same MID3 service data is used for DX1A-2001&2000.
-- 40 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#12): MID3 (VDO-in Data) (Part-2/2)
Register No & Name
YC 480i
Data Initial Setting
(32V&36V CRTs) MID Mode: P&P / Favorite
YPbPr 480P YPbPr 1080i Dummy 480i
Data Initial Setting
(32V&36V CRTs) MID Mode: FREEZE
YPbPr 480P YPbPr 1080i Dummy 480i
Comment
Dummy-480i settings are used for No Signal cases.
#0 VDHP (cont.) #1 VDHS (cont.) #2 VDVE (cont.) #3 VDVS (cont.)
197 219 24 56
127 154 53 112
91 151 37 126
179 199 24 56
131 153 53 112
98 149 37 126
179 199 24 56
Note: The same MID3 service data is used for DX1A-2001&2000.
DX1A-2001&2000 SERVICE LIST (#13): MID5 (Picture Data: MIDE) (Part-1/4)
Device Name: CXD9509AQ { MID-XA / Fujitsu & SONY } / IC3408 (B-board) / P/N: 8-759-672-57 (SBorSD#: NA) Slave Address: 2Eh { Controlled through MID-XA Micro (IC3090/B-board, Slave Address: 64h) / P/N: 6-800-050-01 (SB#: V4216) } MID-XA Micro (MASK type): MB94918RPF-G-137-BND, MID-XA Software: Version 12/08/00, (P/N: 6-800-050-01)
Register No & Name Control Register Function & Link Register Name (Software) Data Type Data Range Data Initial/Average Setting
(32V&36V CRTs) UHF/VHF & CVideo
Pro Movie Standard Vivid Pro
Data Initial/Average Setting
(32V&36V CRTs) YPbPr-480i (DVD)
Movie Standard Vivid
Settings for P&P (Main) 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 POP MHLY MHLC MVLY MVLC MHYR MHYL MHYE MHYO MHCR MHCL MHCE MHCO MVYR MVYL MVYE MVCR MVCL MVCE Selection of service data tables (Table #: 0~15) Y coefficient code of Horizontal LPF (M) m_hlpf_ycoef C coefficient code of Horizontal LPF (M) m_hlpf_ccoef Y coefficient code of Vertical LPF (M) m_vlpf_ycoef C coefficient code of Vertical LPF (M) m_vlpf_ccoef Y coreing code of horizontal enhancement (M) m_henh_ycore Y cliping code of horizontal enhancement (M) m_henh_yclip Y level code of horizontal enhancement (M) m_henh_yenh Y coefficient code of horizontal enhancement (M m_henh_ycof C coreing code of horizontal enhancement (M) m_henh_ccore C cliping code of horizontal enhancement (M) m_henh_cclip C level code of horizontal enhancement (M) m_henh_cenh C coefficient code of horizontal enhancement (M m_henh_ccof Y coreing code of vertical enhancement (M) m_venh_ycore Y cliping code of vertical enhancement (M) m_venh_yclip Y level code of vertical enhancement (M) m_venh_yenh C coreing code of vertical enhancement (M) m_venh_ccore C cliping code of vertical enhancement (M) m_venh_cclip C level code of vertical enhancement (M) m_venh_cenh 0~15 0~3 0~3 0~3 0~3 0~3 0~3 0~7 0, 1 0~3 0~3 0~7 0, 1 0~3 0~3 0~7 0~3 0~3 0~7
0 1 3 0 0 0 1 4 1 0 1 0 1 0 1 0 0 1 0
1 1 3 0 0 0 1 0 1 0 1 0 1 0 1 0 0 1 0
2 1 3 0 0 0 1 0 1 0 1 0 1 0 1 0 0 1 0
3 1 3 0 0 0 1 0 1 0 1 0 1 0 1 0 0 1 0
4 1 3 0 0 0 1 3 1 0 1 0 1 0 1 0 0 1 0
5 1 3 0 0 0 1 0 1 0 1 0 1 0 1 0 0 1 0
6 1 3 0 0 0 1 0 1 0 1 0 1 2 1 2 0 1 0
7 1 3 0 0 0 1 0 1 0 1 0 1 2 1 5 0 1 0
See the next page.
Note: The same MID5 service data is used for DX1A-2001&2000.
-- 41 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#13): MID5 (Picture Data: MIDE) (Part-2/4)
Register No & Name
Data Initial/Average Setting
(32V&36V CRTs) YPbPr-480p
Pro Movie Standard Vivid Pro
Data Initial/Average Setting
(32V&36V CRTs) YPbPr-1080i
Movie Standard Vivid
Comment
#0 POP (cont.) #1 MHLY (cont.) #2 MHLC (cont.) #3 MVLY (cont.) #4 MVLC (cont.) #5 MHYR (cont.) #6 MHYL (cont.) #7 MHYE (cont.) #8 MHYO (cont.) #9 MHCR (cont.) #10 MHCL (cont.) #11 MHCE (cont.) #12 MHCO (cont.) #13 MVYR (cont.) #14 MVYL (cont.) #15 MVYE (cont.) #16 MVCR (cont.) #17 MVCL (cont.) #18 MVCE (cont.)
8 1 3 0 0 0 1 4 1 0 1 0 1 0 1 0 0 1 0
9 1 3 0 0 0 1 0 1 0 1 0 1 0 1 0 0 1 0
10 1 3 0 0 0 1 0 1 0 1 0 1 2 1 2 0 1 0
11 1 3 0 0 0 1 0 1 0 1 0 1 2 1 5 0 1 0
12 1 3 0 0 0 1 4 1 0 1 0 1 0 1 0 0 1 0
13 1 3 0 0 0 1 0 1 0 1 0 1 0 1 0 0 1 0
14 1 3 0 0 0 1 0 1 0 1 0 1 0 1 0 0 1 0
15 1 3 0 0 0 1 0 1 0 1 0 1 0 1 0 0 1 0
Note: The same MID5 service data are used for DX1A-2001&2000.
-- 42 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#13): MID5 (Picture Data: MIDE) (Part-3/4)
Register No.&Name
Control Register Function & Link
Register Name (Software)
Data Type
Data Range
Data Initial/Average Setting
(32V&36V CRTs) UHF/VHF & CV
Pro Movie Standard Vivid Pro
Data Initial/Average Setting
(32V&36V CRTs) YPbPr-480i (DVD)
Movie Standard Vivid
Settings for P&P (Sub) 0 POP 19 SHLY 20 SHLC 21 SVLY 22 SVLC 23 SHYR 24 SHYL 25 SHYE 26 SHYO 27 SHCR 28 SHCL 29 SHCE 30 SHCO 31 SVYR 32 SVYL 33 SVYE 34 SVCR 35 SVCL 36 SVCE Selection of service data tables (Table #: 0~15) Y coefficient code of Horizontal LPF (S) C coefficient code of Horizontal LPF (S) Y coefficient code of Vertical LPF (S) C coefficient code of Vertical LPF (S) Y coreing code of horizontal enhancement (S) Y cliping code of horizontal enhancement (S) Y level code of horizontal enhancement (S) Y coefficient code of horizontal enhancement (S C coreing code of horizontal enhancement (S) C cliping code of horizontal enhancement (S) C level code of horizontal enhancement (S) C coefficient code of horizontal enhancement (S Y coreing code of vertical enhancement (S) Y cliping code of vertical enhancement (S) Y level code of vertical enhancement (S) C coreing code of vertical enhancement (S) C cliping code of vertical enhancement (S) C level code of vertical enhancement (S) s_hlpf_ycoef s_hlpf_ccoef s_vlpf_ycoef s_vlpf_ccoef s_henh_ycore s_henh_yclip s_henh_yenh s_henh_ycof s_henh_ccore s_henh_cclip s_henh_cenh s_henh_ccof s_venh_ycore s_venh_yclip s_venh_yenh s_venh_ccore s_venh_cclip s_venh_cenh 0~15 0~7 0~7 0~7 0~7 0~3 0~3 0~7 0, 1 0~3 0~3 0~7 0, 1 0~3 0~3 0~7 0~3 0~3 0~7
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
3 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
4 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
5 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
6 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
7 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
See the next page.
Note: The same MID5 service data is used for DX1A-2001&2000.
-- 43 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#13): MID5 (Picture Data: MIDE) (Part-4/4)
Register No.&Name
Data Initial/Average Setting
(32V&36V CRTs) YPbPr-480p
Pro Movie Standard Vivid Pro
Data Initial/Average Setting
(32V&36V CRTs) YPbPr-1080i
Movie Standard Vivid
Comment
#0 POP (cont.) #19 SHLY (cont.) #20 SHLC (cont.) #21 SVLY (cont.) #22 SVLC (cont.) #23 SHYR (cont.) #24 SHYL (cont.) #25 SHYE (cont.) #26 SHYO (cont.) #27 SHCR (cont.) #28 SHCL (cont.) #29 SHCE (cont.) #30 SHCO (cont.) #31 SVYR (cont.) #32 SVYL (cont.) #33 SVYE (cont.) #34 SVCR (cont.) #35 SVCL (cont.) #36 SVCE (cont.)
8 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
9 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
10 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
11 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
12 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
13 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
14 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Note: The same MID5 service data are used for DX1A-2001&2000.
DX1A-2001* SERVICE LIST (#14): On-Screen Display (OSD)
Device Name: M306V2ME-153FP (V1.0) { System Micro (MASK type) / Mitsubishi } / IC701 (A-board) Slave Address: 60h System Micro (MASK type): M306V2ME-153FP, Sys-Software: Version 1.0, P/N: 6-800-051-01 (SB#: V9091)
Register No & Name Control Register Function & Link Data Type Data Range Data Initial/Average Setting
(32V&36V CRTs)
Comment
C: Common data
0 1 2 3
HPOS HPOF VPOS VPOT
OSD horizontal position Horizontal position for Favorite mode OSD vertical position Vertical position for P&P (Twin) mode
C C C C
0~255 0~255 0~255 0~255
23 33 5 32
Note: * This OSD settings are used for DX1A-2001 ONLY. (DX1A-2000 uses two OSD settings based on two versions of system micros.)
-- 44 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#15): SNNR
Related Control Devices: mPD64082 { 3D-Comb / NEC } / IC3501 (BC-board) / Slave Address: B8h CXA2103Q { Chroma Decoder / SONY } / IC3048 (B-board) / Slave Address: 9Ah (Main) CXA2150Q { CRT Driver / SONY } / IC201 (A-board) / Slave Address: 86h
Register No & Name Control Register Function & Link Data Type Data Range Data Initial/Average Setting
32V&36V CRTs
Comment
0 1
SNNR
SNNR data setting Selection of SNNR data settings; SNFX 0: Set SNNR automatically according to WSLT value (read data) Noise level detection data thretholds for SNNR data (read data)
SNNR data used as the (-) offset settings
0~3 C 0, 1
0 0
WSLT Data / Threthold Range
C: Comon data
2
WSLT
0~255 0~3 ----------------------------------------------------------------------------
0~30 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0
31~62 1 1 0 1 1 0 1 1 1 1 0 0 0 0 +1
63~126 127~255 2 2 0 1 1 0 2 2 3 2 0 0 0 0 +2 3 3 0 1 1 0 3 3 4 3 0 0 0 0 +3
SNNR Settings Based on WSL Data ( - Offset Data)
3 4 5 6
CPFG CPFT CCOR CHCG
SNNR = 0/1/2/3 @ WSLT £ 0/31/63/127, respectively Related to 3D-COMB (mPD64082) / #19 YPFG settings Related to 3D-COMB (mPD64082) / #18 YPFT settings
SNNR data used as the direct settings
Related to 3D-COMB (mPD64082) / #20 YHCO settings Related to 3D-COMB (mPD64082) / #21 YHCG settings
SNNR data used as the (-) offset settings
7 CAPG 8 3SHP 9 MIDD 10 5SHP 11 5YF1 12 5CDS 13 5LTI 14 5CTI 15 5VML 16 5VMC
Related to 3D-COMB (mPD64082) / #16 VAPG settings Related to CXA2103 / #6 SHAP settings Related to CXA2150P-3 / #19 MIDE settings Related to CXA2150P-4 / #4 USHP settings Related to CXA2150P-3 / #10 F1LV settings Related to CXA2150P-3 / #11 CDSP settings Related to CXA2150P-3 / #12 LTLV settings Related to CXA2150P-3 / #14 CTLV settings Related to CXA2150P-3 / #1 UVML settings
SNNR data used as the (+) offset settings
SNNR Settings Based on WSL Data ( + Offset Data)
Related to CXA2150P-3 / #3 VMCR settings
Note: The same SNNR service data is used for DX1A-2001&2000. Please refer to the part numbers and SBorSD numbers given in the service list for these devices.
-- 45 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#16): ID-1 Detection (ID1)
Device Name: CXD2085M { ID-1 Decoder / SONY } / IC3603 (B-board) / P/N: 8-752-395-13 (SD#: S98511B) Slave Address: 40h
Register No & Name Control Register Function & Link Data Type Data Range Data Initial/Average Setting
(32V&36V CRTs)
Comment
0 1
XJGL LNJI
XJGLK: Setting for memorizing or not the ID-1 detection status LNJ1: Setting for the multi/single-line ID-1 detection
C C
0, 1 0, 1
0 0
C: Common data
Note: The same ID1 service data are used for DX1A-2001&2000. Other servcie controls related to CXD2085 (IDSW & DATA) are lised in Service List (CXA2150P-4) for easier engineering adjustment.
DX1A-2001&2000 SERVICE LIST (#17): Closed Caption Display & Parental Control (CCD&VCHIP)
Device Name: CXP85840A-039Q { CCD&Vchip Micro (MASK type) / SONY } / IC3602 (Main) & IC3601 (Sub) (B-board) / P/N: 8-752-916-40 (SD#: S97739B) Slave Address: 68h (Main) & 6Ch (Sub) CCD&Vchip Micro Software: Version 2.14
Register No & Name Control Register Function & Link Data Type Data Range Data Initial/Average Setting
(32V&36V CRTs)
Comment C: Common data
0 HPRM 1 HPRS 2 RND 3 CCDI 4 CRIP 5 CRIT 6 CHMK 7 FPOL 8 LANG 9 DATA 10 VCHIP
Horizontal position of CCD (Main) Horizontal position of CCD (Sub) OSD rounding control Interuption cointrol CRI count & parity count Charge/Discharge timing control for slice voltage level Horizontal mask width Field polarity selection Switch for CCD service/test data Selection of Vchip controls
C C C C C C C C C C C
0~255 0~255 0, 1 0~7 0~7 0, 1 0~63 0, 1 0~3 0, 1 0, 1
46 46 1 3 4 0 42 1 0 0 0
0: MASK-type micro, 1: OTP-type micro
Note: The same CCD&VCHIP service data is used for DX1A-2001&2000.
-- 46 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#18): OPTIONS (OP)
Device Name: M306V2ME-153FP (V1.0) { System Micro (MASK type) / Mitsubishi } / IC701 (A-board) Slave Address: 60h System Micro (MASK type): M306V2ME-153FP, Sys-Software: Version 1.0, P/N: 6-800-051-01 (SB#: V9091)
Register No & Name Control Register Function & Link Data Type Data Range Data Initial/Average Setting
(32V&36V CRTs)
Comment C: Common data
0 1 2 3
DLY1 DLY2 DLY3 RAMW
AC-RLY to MAIN-RLY timing = DLY1 x 50 ms Power-On Mute timing = DLY2 x 50 ms DGC-RLY to MAIN-RLY timing = DLY3 x 50 ms RAM monitor on/off
C C C C
0~15 0~31 0~15 0, 1
4 12 7 0
Note: The same OP service data is used for DX1A-2001&2000.
DX1A-2001* SERVICE LIST (#19): IDENTIFICATION (ID)
Device Name: M306V2ME-153FP (V1.0) { System Micro (MASK type) / Mitsubishi } / IC701 (A-board) Slave Address: 60h System Micro (MASK type): M306V2ME-153FP, Sys-Software: Version 1.0, P/N: 6-800-051-01 (SB#: V9091)
Register No & Name Control Register Function & Link Shipping Destination-related Settings Data Type Data Range Data Initial/Average Setting
(32V/36V/40V CRTs) KV-32HS20 KV-36HS20 KV-32HS20H KV-32XBR450 KV-36XBR450 KV-36XBR450H KV-32XBR450C KV-36XBR450C
Comment
0 1 2 3 4 5 6 7
ID0 ID1 ID2 ID3 ID4 ID5 ID6 ID7
Selection of OSD languages & color systems Selection of composite & s-video inputs Selection of audio-related controls Selection of basic system settings Selection of basic system settings Selection of advanced system settings Selection of sub picture-related settings Selection of some reserved settings
0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255
89 127 239 98 203 177 54 24
89 127 255 106 203 177 54 24
89 127 255 90 203 177 54 24
Note: * These ID settings are used for DX1A-2001 ONLY. (DX1A-2000 uses different ID settings.) The system micro name, software&patch versions, and the status of NVM devices are displayed only when in this service catergory (#19): ID.
-- 47 --