Text preview for : goodmans 1425rs - Gd1425RS.pdf part of Goodmans 1425RS 1425RS Goodmans
Back to : goodmans 1425rs - Gd1425R | Home
GOODMANS 1425 RS
General Information Also Covers 2025 RS, 2045 TS, 2145 TS. Daewoo CP-375
1
6.3 VERTICAL SLOPE * The VERTICAL SIZE adjustment has to be done in advance. 1) Apply a RETMA PATTERN signal. 2) Adjust the lower part of the picture with the VSLOPE UP/DOWN keys. * Option
Initial state (Blank EEPROM) AV BAND FRANCE N3.58 ATS AV2 3 BAND OFF OFF ON TA (FRANCE) AV2 3 BAND ON OFF ON TU (UK) AV2 1 BAND OFF OFF ON TF,TK (OTHERS) AV2 3 BAND OFF OFF ON DW5255M2-3 DW5255M4 DW5255RM1 -2 DW5255RM3 Remark (u-COM Version)
X-Ray Precautions
Safety Instruction 1.Excessive high voltage can produce potentially hazardous X-RAY RADIATION.To avoid such hazards, the high voltage must not exceed the specified limit. The nominal value of the high voltage of this receiver is 22-23KV (14"),25-26Kv (20", 21") at max beam current. The high voltage must not, under any circumstances, exceed 27.5 NV (14", 20"), 29.0Kv (21'). Each time a receiver requires servicing, the high voltage should be checked. It is important to use an accurate and reliable high voltage meter. 2. The only source of X-RAY Radiation in this TV receiver is the picture tube.For continued XRAY RADIATION protection,the replacement tube must be exactly the same type tube as specified in the parts list. 2) Connect the Signal Generator RF Output to P101 (Tuner IF Output). There must be no signal input to the tuner. 3) Press the `AFT' KEY and wait until the TV screen display "AFT OK". 1.2 Standard SECAM-L' (France VHF-Low) * Above mentioned "1.1," adjustment has to be done in advance. 1) Set a Signal Generator with - RF FREQUENCY = 34.2 MHz, - RF OUTPUT LEVEL =800 ±5 dBuV - System = SECAM 2) Connect the Signal Generator RE Output to P101 (Tuner IF Output). There must be no signal input to the tuner. 3) Press the "L' AFT" KEY and wait until the TV screen display "L AFT OK". 2. AGC 1) Set a Pattern Generator with RF LEVEL 630±2 dBuV. 2) Connect a OSCILLOSCOPE PROBE to P101 (TUNER AGC INPUT). 3) Adjust AGC UP/DOWN KEY the voltage drop 1V dc over below its maximum voltage.
* Alternative Method 1) Set a Pattern Generator with - RF LEVEL 800±5 dBuV - PAL CROSSHATCH (without SOUND CARRIER) 2) Connect a OSCILLOSCOPE (Bandwidth 100MHz) PROBE to P101 (TUNER IFOUTPUT). 3) Use AGC UP/DOWN KEY to obtain an envelop amplitude 200 + 50 mVp-p. 3. SCREEN 1) Apply a COLOR BAR pattern signal. 2) Set the CONTRAST, BRIGHTNESS to MAX, COLOR to MIN. 3) Set the R,G,B LEVEL to CENTRE (31/63) with R,G,B UP/DOWN KEY. 4) Connect a OSCILLOSCOPE PROBE to P906 (CRT CATHOD R, G, B). 5) Adjust the SCREEN VOLUME on FBT such that the highest black level voltage 1600 ±5Vdc (20", 21"), 1300±5Vdc (14").
6.4 VERTICAL S-CORRECTION 1) Apply a CROSSHATCH PATTERN signal. 2) Adjust the 5-COR UP/DOWN KEY to obtain the same distance between horizontal lines.
* The initial state of adjustment are as follows; V-Center, V-Slope V-Size, H-Center, R, G, B, AFT = Center (30/64 - 33/64) S-Correction = 00/64 AGC = 10/64
Waveforms
6.5 HORIZONTAL CENTRE 1) Apply a RETMA PATTERN signal. 2) Adjust picture centering with CENTRE LEFT/ RIGHT keys. If EEPROM (I703) has been changed; - Option data has to be changed and - all alignment function has to be readjusted. * Service Remocon
Adjustments
1. AFT 1.1 Standard B/G,D/K,I and L 1) Set a Signal Generator with - RF FREQUENCY = 38.9 MHz, - RF OUTPUT LEVEL = 800 ±5 dBuV - System = PAL / SECAM - B/G, D/K, I
4. WHITE BALANCE 1) Set the TV to NOR I mode. 2) Set the R,G,B LEVEL to CENTRE with R,G,B UP/DOWN KEY. 3) Adjust the R,G,B UP/DOWN KEY of the other color which did not appear on the screen to obtain WHITE. 5. FOCUS
Recommended Safety Parts
Item
ZZ131 V901 C409 C410 C411 C801-2 C803 C804 C805 C806 C817 D401 D402 D403 D409 D420 D801-4 D805 D806 D807 D808 D811 D812 D813 F801 F801A-B I801 I804 L801 PWC1 Q401 Q402 R415 R801 R802 R804 SCT1 SW801 T401 T402 T801
Part No.
58G0000084 48A96414P1 CCXB3D471K CMYH3C752J CMYE2D514J CL1JB3474K CCXE2H472P CCXE2H472P CEYM2G121T CCYR3D471K CCYR3D681K DBYV95C-- DBYV95C-- DBYV95C-- DBY228-- DBYV95C-- D1S1888-- DBYV95C-- DBYV95C-- DBYV95C-- DBYV95C-- DBYV95C-- DBYV95C-- DBYV95C-- 5FSCB4O22R 4857415001 1STRS5707-- 1LTV817C-- 5PLF20A1-- 4859903110 T2SD2499-- T2SD1207T-- RF01Z129JA DEC180M290 RX10B339JN RF02Z568J-- 4859303030 5S40101143 50D10A2-- 50H0000177 50M3934A1--
Description
COIL DEGAUSSING CRT BARE C CERA C MYLAR C MYLAR C LINE ACROSS C CERA C CERA C ELECTRO C CERA C CERA DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE FUSE CERA CLIP FUSE IC POWER IC PHOTO COUPLER FILTER LINE CORD POWER AS TR TR R FUSIBLE POSISTOR R CEMENT R FUSIBLE SOCKET CRT SW PUSH TRANS DRIVE FBT TRANS SMPS DC-1450 A34JLL90X 2KV B 470PF K 1.6KV BUP 7500PF J 200V PU 0.51MF J AC250V 0.47MF 500V E 4700PF P 500V E 4700PF P 400V LWF 120MF HIKR 2KV 470PF K 125C 2KV R 680PF K 125C BYV95C (TAPPING) BYV95C (TAPPING) BYV95C (TAPPING) BY228 (TAPPING) BYV95C (TAPPING) 1S1888 (TAPPING) BYV95C (TAPPING) BYV95C (TAPPING) BYV95C (TAPPING) BYV95C (TAPPING) BYV95C (TAPPING) BYV95C (TAPPING) BYV95C (TAPPING) SEMKO F4AH 4A 250V PFC5000-0702 STR-S5707 LTV-817C LF-20A1 2SD2499 2SD1207-T (TAPPING) 1W 1.2 OHM J A CURVE ECPCC180M290 10W 3.3 OHM J BENCH 2W 0.56 OHM J ISMM03S PS3-22SP (P.C.B) TD-10A2 HST1142.5057 TSM-3934A1
1) Apply a RETMA PATTERN signal. 2) Adjust the FOCUS VOLUME on FBT to obtain optimal resolution. 6. GEOMETRY 6.1 VERTICAL CENTRE 1) Set the TV to NOR I mode. 2) Pressing the V-SIZE UP/DOWN KEY, the lower half of the screen is blanked. 3) Adjust the border line of blanked picture coincident with the mechanical center marks of the CRT using the V-SIZE UP/DOWN KEY.
6.2 VERTICAL SIZE * The VERTICAL CENTRE adjustment has to be done in advance. 1) Apply a RETMA PATTERN signal. 2) Set the TV to NOR I mode. 3) Adjust the upper part of the picture with the VSIZE UP/DOWN keys.
Adjustments / Safety Parts / X-Ray Precautions / CRT Diagram / CRT Type Table / Remote Control / Tube Size Table / Main Diagram / Waveforms
GOODMANS 1425 RS
No. Loc. V901 SCT1 SCT2 LP03 LP04 L405 C410 C409 C411 R413 R415 R302 R901-3 R904-6 R807 P401 P401A Name CRT BARE SOCKET CRT SOCKET CRT COIL BEAD COIL BEAD COIL H-LIN. C MYLAR C CERA C MYLAR R C-FILM R FUSIBLE R C-FILM R C-FILM R C-FILM R C-FILM CONN WAFER CONN AS 14" OEC A34JLL90X 48A96414P1 2 3 4 5 ISMM03S 4859303030 -- MD-5 5MC0000100 -- L-125 58H0000018 7 8 9 10 11 12 13 14 15 16 17 1.6KV 7500 CMYH3C752J 2KV 470 CCXB3D471K 200V 0.51 CMYE2D514J 1/4W 120K RD-4Z124J1W 1.2A(F) RF01Z129JA 1/6W 1.8K RD-AZ182J1/6W 3K RD-AZ302J1/6W 2K RD-AZ202J1/4W 2.4K RD-4Z242JYFW500-05 4859240020 -- MD-5 ISHS09S
2
14" Polkolor A34EFU13X01 4859606640 -- ISMM03S 4859303030 -- -- MD-5 5MC0000100 L-102 58H0000016 1.6KV 6200 CMYH3C622J 2KV 470 CCXB3D471K 200V 0.51 CMYE2D514J 1/4W 82K RD-4Z823J 1W 0.47(F) RF01Z478J1/6W 1.8K RD-A7182J1/6W 3K RD-AZ302J1/6W 2K RD-AZ202J1/4W 2.4K RD-4Z242JYFW500-06 4859240120 35135/0620 +35179 +ULW = 350 4850706S20 DC1450 58G0000084 ECPCC 180M290 DEC180M290 1401H-1015-1P 48519A4610 -- DC2050 58G0000086 ECPCC 180M290 DEC180M290 2001H-1015-1P 48519A5010 -- 4850706057 DC2050 58G0000086 ECPCC 180M290 DEC180M290 2001H-1015-1P 48519A5010 -- DC2070 58G0000074 ECPCC 140M290 DEC140M290 2101H-1015-1P 48519A5210 250V RSS 33MF CEXF2E330V 4850706057 DC2070 58G0000074 ECPCC 140M290 DEC140M290 2101H-1015-1P 48519A5210 -- 4850706057 DC2070 58G0000074 ECPCC 140M290 DEC140M290 2101H-101548519A5210 -- L-102 58H0000016 1.6KV 7500 CMYH3C752J 2KV 470 CCXB3D471K 200V 0.47 CMYE2D474J 1/4W 68K RD-4Z683J 1W 2.4A (F) RF01Z249JA 1/6W 2.2K RD-AZ222J 1/6W 2K RD-AZ202J1/6W 1.6K RD-AZ162J1/4W 2.7K RD-4Z272JYFW500-05 4859240020 -- 4859302930 -- MD-5 5MC0000100 -- MD-5 5MC0000100 L-76 58H0000020 1.6KV 7200 CMYH3C722J 2KV 220 CCXB3D221K 200V 0.39 CMYE2D394J 1/4W 82K RD-4Z823J 1W 0.47(F) RF01Z478J1/6W 2.2K RD-AZ222J 1/6W 2K RD-AZ202J1/6W 1.6K RD-AZ162J1/4W 2.7K RD-4Z272JYFW500-06 4859240120 ODY-2109 MD-5 5MC0000100 L-102 58H0000016 1.6KV 6000 CMYH3C602J 2KV 470 CCXB3D471K 200V 0.3 CMYE2D304J 1/4W 68K RD-4Z683J 1W 1 (F) RF01Z109J1/6W 2.7K RD-AZ272J 1/6W 2K RD-AZ202J1/6W 1.6K RD-AZ162J1/4W 2.7K RD-4Z272JYFW500-06 4859240120 -- L-125 58H0000018 1.6KV 6900 CMYH3C692J 2KV 470 CCXB3D471K 200V 0.51 CMYE2D514J 1/4W 68K RD-4Z683J 1W 1.2A(F) RF01Z129JA 1/6W 2.2K RD-AZ272J 1/6W 2K RD-AZ202J1/6W 1.6K RD-AZ162J1/4W 2.7K RD-4Z272JYFW500-06 4859240120 ODY-2109 L-102 58H0000016 1.6KV 7500 CMYH3C752J 2KV 470 CCXB3D471K 200V 0.51 CMYE2D514J 1/4W 68K RD-4Z683J 1W 2.7A(F) RF01Z279JA 1/6W 2.7K RD-AZ272J 1/6W 2K RD-AZ202J1/6W 1.6K RD-AZ162J1/4W 2.7K RD-4Z272JYFW500-06 4859240120 ODY-2109 5MC0000100 ISMM03S 4859303030 -- ISHS09S 4859302930 -- -- -- ISMM03S 4859303030 -- ISHS09S 4859302930 MD-5 5MC0000100 -- ISHS09S 4859302930 MD-5 5MC0000100 -- -- -- 14" PHILIPS A34EAC01X 20" OEC A48JLL90X01 20" Polkolor A48EEV33X01 21" OEC A51JSW90X02 21" Polkolor A51EBV13X09 21" PHILIPS A51EAL55X01 1
CRT Type Table
(Difference of Parts for CRT)
CRT Diagram
6
L-102 58H0000016 1.6KV 6200 CMYH3C622J 2KV 470 CCXB3D471K 250V 0.68 J CMYT2E684J 1/4W 68K RD-4Z683J 1W 0.18(F) RF01Z188J1/6W 2.2K RD-AZ222J 1/6W 3K RD-AZ302J1/6W 2K RD-AZ202J1/4W 2.4K RD-4Z242JYFW500-06 4859240120 35135/0620 +35179 +ULW = 350 4850706S20
18 19
ZZ131 P801
COIL DEGAUSS POSISTOR
DC1450 58G0000084 ECPCC 180M290 DEC180M290
DC1450 58G0000084 ECPCC 180M290 DEC180M290 1401H-1015-1P 48519A4610 --
20 21
ZZ132 C910
CRT GND AS C ELECTRO
1401H-1015-1P 48519A4610 --
Tube Size Table Remote Control Diagram
NO. 1
LOC. CRT ORION A34JLL90X
14" PHILIPS A34EAC01X ISMM03S DC-1450 ECPCC180M29 MD-5 L-125 2KV 470 1.6KV 6200 200V 0.51 1/6w 1.6K 1/4w 120K 1W 0.47(F) 1/4W 2.4K 1/6W 3K 1/6W 2K YFWS00-06 35135/0620+ 35179+ULW =350 POLKOLOR A34EFU13X ISHS09S DC-1450 ECPCC1BOM29O MD-5 L-102 2KV 470 1.6KV 6200 250V 0.68 1/6w 2.2K 1/4W 68K 1W 0.18(F) 1/4W 2.4K 1/6W 3K 1/6w 2K YFWS00-06 35135/0620+ 35179+ULW =350 1401H-1015-1P 2001H-1015--1P ORION A48JLL90X ISMM03S DC-2050 ECPCC180M290 MD-5 L-102 2KV 470 1.6KV 7500 200V 0.47u 1/6w 2.2K 1/4w 68K 1W 2.4(F) A 1/4W 2.7K 1/6W 2K 1/6W 1.6K YFWS00-05
20" SAMSUNG A48ECR11X ISHS09S DC-2050 ECPCC180M290 MD-5 L-102 2KV 1000 1.6KV 8200 200V 0.51 1/6w 2.2K 1/4w 68K 1W 1(F) 1/4W 2.7K 1/6W 2K 1/6W 1.6K YFWS00-06 POLKOLOR A48EEV33X ISHS09S DC-2050 ECPCC180M290 MD-5 L-76 2KV 220 1.6KV 7200 200V 0.39u 1/6W 2.2K 1/4w 82K 1W 0.47(F) 1/4W 2.7K 1/6W 2K 1/6W 1.6K YFW500-06 ORION A51JSW90X ISMM03S DC--2070 ECPCC140M290 MD-5 L-102 2KV 220 1.6KV 6000 200V 0.3u 1/6W 2.7K 1/4W 68K 1W 1.2(F) A 1/4W 2.7K 1/6W 2K 1/6W 1.6K YFWS00-06
21" PHILIPS A51EAL55X ISHS09S DC--2070 ECPCC140M290 MD-5 L-102 2KV 470 1.6KV 7500 200V 0.51 1/6w 2.7K 1/4W 82K 2W 2.7(F) A 1/4W 2.7K 1/6W 2K 1/6W 1.6K YFW500-06 POLKOLOR A51EER11X ISHS09S DC--2070 ECPCC140M290 MD-5 L-125 2KV 470 1.6KV 6000 200V 0.47 1/6W 2.2K 1/4W 68K 1W 1.2(F) 1/4w 2.7K 1/6W 2K 1/6W 1.6K YFW500-06
2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
SCT1 SCT2 D/COIL R801 LP04 LP03 L405 C409 C410 C411 R302 R413 R415 R807 R901-3 R904-6 P401
ISMM03S DC-1450 ECPCC180M290 MD-5 L-125 2KV 470 1.6KV 7500 200V 0.51 1/6w 1.8K 1/4w 120K 1W 1.2(F) A 1/4W 2.4K 1/6W 3K 1/6W 2K YFWS00-05 -
19
P401A
-
ODY--2190
ODY--2190
-
0DY-2190
0DY-2190
20
ZZ132
1401H-101S-1P
1401H-1015-1P
2001H-1015-1P
2001H-1015-1P
2101H-1015-1P
2101H-1015-1P
2101H-1015-1P
Adjustments / Safety Parts / X-Ray Precautions / CRT Diagram / CRT Type Table / Remote Control / Tube Size Table / Main Diagram / Waveforms
GOODMANS 1425 RS
3
Main Diagram
Adjustments / Safety Parts / X-Ray Precautions / CRT Diagram / CRT Type Table / Remote Control / Tube Size Table / Main Diagram / Waveforms