Text preview for : S0NY KV_32HS20_36HS20_32XBR450_36XBR450_36XBR450H.pdf part of SONY KV_32HS20_36HS20_32XBR450_36XBR450_36XBR450H S.M.
Back to : S0NY KV_32HS20_36HS20_32 | Home
Self Diagnosis
Supported model
SERVICE MANUAL
MODEL NAME REMOTE COMMANDER DESTINATION
DX-1A CHASSIS
CHASSIS NO.
KV-32HS20 KV-36HS20 KV-36HS20H KV-32XBR450 KV-32XBR450 KV-36XBR450 KV-36XBR450 KV-36XBR450H
RM-Y183 RM-Y183 RM-Y183 RM-Y184 RM-Y184 RM-Y184 RM-Y184 RM-Y184
US US HAWAII US CND US CND HAWAII
SCC-S47F-A SCC-S47E-A SCC-S54C-A SCC-S47D-A SCC-S48D-A SCC-S47C-A SCC-S48C-A SCC-S54B-A
KV-32XBR450
RM-Y184
TRINITRON® COLOR TELEVISION
9-965-898-01
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
SECTION 4: CIRCUIT ADJUSTMENTS ELECTRICAL ADJUSTMENTS BY REMOTE COMMANDER
Use the Remote Commander (RM-Y183, RM-Y184) to perform the circuit adjustments in this section. Test Equipment Required: 1. Pattern generator 2. Frequency counter 3. Digital multimeter 4. Audio oscillator
4-1. SETTING THE SERVICE ADJUSTMENT MODE
1. Standby mode (Power off). 2. Press the following buttons on the remote commander within one second of each other: Channel 5 Sound Volume + Power DISPLAY
4-2. MEMORY WRITE CONFIRMATION METHOD
1. After adjustment, pull out the plug from the AC outlet, then replace the plug in the AC outlet again. 2. Turn the power switch ON and set to Service Mode. 3. Call the adjusted items again to confirm they were adjusted.
SERVICE ADJUSTMENT MODE VIEW
Device Item 2150P-1 SBOT 0 Data Item +7 SERVICE TV
4-3. REMOTE ADJUSTMENT BUTTONS AND INDICATORS
Register Item
WSL: 0
F/A FLAG: CBA FLAG:
WRITE INTO MEMORY
DEVICE UP
READING THE MEMORY
1. Enter into service mode. 2. Press 0 on the remote commander. 3. Press ENTER to read memory.
ITEM UP ITEM DOWN
DATA UP DATA DOWN DEVICE DOWN EXECUTE READ MEMORY
ADJUSTING THE PICTURE
1. 2. 3. 4. 5. Enter into service mode Press 2 or 5 on the remote to select the device item. Press 1 or 4 on the remote to select an item. Press 3 or 6 on the remote to change the data. Press MUTING then ENTER to write into memory.
TEST RESET
4-1.1 RESETTING THE DATA
Note: Be careful when using the remote! It will clear and re-initialize ALL NVM data including deflection adjustment data if not reset properly as follows:
RESETTING THE DEFLECTION NVM DATA
1. Enter into service mode. 2. Press 7 , then MENU , and then press ENTER on the remote.
RESETTING THE SYSTEM NVM DATA
1. Enter into service mode. 2. Press 7 , then 9 , and then press ENTER on the remote.
RESETTING THE SYSTEM NVM DATA
1. Enter into service mode. 2. Press 8 and then press ENTER on the remote.
RM-Y183 (KV-32HS20/36HS20/36HS20H ONLY)
-- 18 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
WRITE INTO MEMORY
DEVICE UP
ITEM UP ITEM DOWN
DATA UP DATA DOWN DEVICE DOWN EXECUTE READ MEMORY
TEST RESET
RM-Y184 (KV-32XBR450/36XBR450/36XBR450H ONLY)
-- 19 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
SERVICE DATA LISTS
DX1A-2001* Service List ------ Contents & Notes
Device Name mPD64082 CXA2103Q IC3048 (Main) / B-board IC3110 (Sub) / B-board IC201 / A-board 86h 9Ah 9Eh IC3501 / BC-board B8h (W) & B9h (R) W&R: Write & Read Device Reference Number Slave Address Comment
Category Number & Name
#1
3D-COMB
# 2-1 # 2-2 CXA2150AQ
CXA2103-1 (Main) CXA2103-2 (Sub)
# 3-1 # 3-2 # 3-3 # 3-4 CXA2150AQ CXA2151Q CXA8070P CXA2026AS BH3868AFS NJM2180M CXD9509AQ CXD9509AQ CXD9509AQ CXD9509AQ IC3408 / B-board IC3408 / B-board 2Eh 2Eh IC3408 / B-board 2Eh IC3408 / B-board 2Eh IC4101 / S-board 2Eh IC7001 / A-board 82h IC5511 / D-board 8Eh IC5513 / D-board DEh IC3001 / B-board 84h IC201 / A-board 86h
CXA2150P-1 CXA2150P-2 CXA2150P-3 CXA2150P-4
# 4-1 # 4-2 # 4-3
CXA2150D-1 CXA2150D-2 CXA2150D-3
#5
CXA2151
#6
D-CONV
#7
CXA2026
#8
AP
#9
TRUS
Controlled through CXA1315M ( IC4103 / S-board / 48h ) Controlled through MID-XA Micro ( IC3090 / B-board / 64h ) Controlled through MID-XA Micro ( IC3090 / B-board / 64h ) Controlled through MID-XA Micro ( IC3090 / B-board / 64h ) Controlled through MID-XA Micro ( IC3090 / B-board / 64h )
# 10
MID1
# 11
MID2
# 12
MID3
# 13
MID5
# 14
OSD
# 15 CXD2085M CXP85840A-039Q IC3603 / B-board IC3602 (Main) / B-board IC3601 (Sub) / B-board
SNNR
M306V2ME-153FP mPD64082 CXA2103Q CXA2150Q
IC701 / A-board IC3501 / BC-board IC3048 (Main) / B-board IC201 / A-board
60h DX1A-2001 System Micro {V1.0} B8h (W) & B9h (R) 9Ah 86h 40h 68h (Main) 6Ch (Sub) CCD&Vchip Micro (V2.14)
# 16
ID1
# 17
CCD&VCHIP
# 18 OP # 19 ID DX1A-2001 System Micro & Notes for Services DX1A-2001 MID-XA Micro
M306V2ME-153FP IC701 / A-board 60h DX1A-2001 System Micro {V1.0} M306V2ME-153FP IC701 / A-board 60h DX1A-2001 System Micro {V1.0} M306V2ME-153FP (MASK), Software Version 1.0, IC701/A-board (Slave Adress: 60h) The system micro name, software&patch versions, and the status of NVM devices are displayed only when in the service catergory
MB94918RPF-G-137-BND (MASK), Software Version 12/08/00, IC3090/B-board (Slave Address: 64h) DX1A-2001 CCD&Vchip Micros CXP85840A-039Q (MASK), Software Version 2.14, IC3602/B-board (Main/Slave Address: 68h) & IC3601/B-board (Sub/Slave Address: 6
Note: * This service list is used for DX1A-2001 ONLY. Some service data is the same in DX1A-2001 & 2000, as noted in the data sheets.
-- 20 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#1): 3D-COMB / mPD64082 (Part-1/4)
Device Name: mPD64082GF { 3D-Comb Filter / NEC } / IC3501 (BC-board) / P/N: 8-759-594-44 (SB#: V7372) Slave Address: B8h (Write Address) / B9h (Read Address)
Data Initial/Average Setting
(32V&36V CRTs) UHF/VHF & CVideo
Standard Non-standard Standard Non-standard
Register No & Name Control Register Function & Link Comment
SVideo
Data Type
Data Range
0 C C
UHF/VHF & CVideo
Standard Non-standard Standard Non-standard
NRMD 0~3 0~3
SVideo
0~3 3 1 0 0 0
0
1
3
3
CVideo (CV): CVideo1~4 inputs SVideo (SV): SVideo1~3 inputs C: Common data
1
YAPS
2
CLKS
Operation mode setting Y-output correction (V-aperture compensation & Y-peaking filtering) System clock setting
3 4 5 C C C
NRMD = 0 NRMD = 1
NSDS MSS KILS 0~7 2 10 5 5 2 10 5 5 3
NRMD = 2
0~3 0~3 0~3
0 0 1
6
CDL
Selection for standard/non-satndard signal processing Selection for inter-frame/inter-line processing Killer processing selection C-signal phase with respect to the Y-signal (Fine adjustment at 70 ns/step)
NRMD Setting-based Control Table for DYCO, DYGA, DCCO, DCGA
NRMD = 3
7 8 9 10 11 12 C C
UHF/VHF Video1~4
DYCO DYGA DCCO DCGA YNRL CNRL 0~3 0~3 0~3 1 2
VM = Off
DY detection coring level (Y motion detection coring) DY detection gain (Y motion detection gain) DC detection coring level (C motion detection coring) DC detection gain (C motion detection gain) Frame recersive YNR nonlinear filter limit level Frame recersive CNR nonlinear filter limit level 1 1 1 2
VM = Low
0~15 0~15 0~15 0~15 0~3 0~3
2 10 5 5 1 1
2 10 5 5
Video5&6
13 VTRH
1 1 2
Video1~4: CVideo1~4 & SVideo1~3 inputs Video5&6: YPbPr-480i/480p/1080i inputs
14 VTRR
15 LDSR
Hysteresis for Hsync non-standard signal detection (out-of-Hsync intra-field) Sensitivity for Hsync non-standard signal detection (out-of-Hsync intra-field) Sensitivity for frame non-standard signal detection (out-of-Hsync inter-frame)
VM&SNNR Setting-based Control Table for VAPG & VAPI VAPG= VAPG1 - VAPG2
VAPG1 Data Based on MENU/VM Setting
VM = Mid VM = High
This setting continues to the next page.
16 VAPG 17 VAPI
V-aperture compensation gain V-aperture compensation convergence point
0~7 0~31 0~3 0~15
0 4 0 7
2 4
SNNR = 0
3 4
SNNR = 1
4 4 (32V) or 8 (36V)
SNNR = 2
{Initial/CBA Data = 8}
SNNR Setting (-Offset)
SNNR = 3
SNNR Setting-based Control Table for YPFT & YHFG
18 YPFT 19 YPFG
Y peaking filter (BPF) center frequency Y peaking filter (BPF) gain
0 0
0 1
0 2
0 3
Note: The same 3D-COMB service data is used for DX1A-2001&2000.
DX1A-2001&2000 SERVICE LIST (#1): 3D-COMB / mPD64082 (Part-2/4)
Data Initial/Average Setting
(32V&36V CRTs) VAPG2 Data Based on SNNR/Offset-setting
SNNR = 0 SNNR = 1 SNNR = 2 SNNR = 3
Register No & Name
Comment
#16 VAPG (cont.
0
0
0
0
Note: The same 3D-COMB service data is used for DX1A-2001&2000.
-- 21 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#1): 3D-COMB / mPD64082 (Part-3/4)
Data Initial/Average Setting
(32V&36V CRTs) SNNR = 0 SNNR = 1 SNNR = 2 SNNR = 3
Register No. & Name Control Register Function & Link Data Type Data Range
Comment (Not SNNR Offset Data) YHCO&YHCG settings are sent directly to 3D-Comb device.
SNNR Setting-based Control Table for YHCO & YHCG
1 0
C: Common data
20 21 22 23 24 C C C
NRMD = 0 NRMD = 1 NRMD = 2 NRMD = 3
YHCO YHCG HSSL VSSL ADCL 4 4 4
Y output high frequency component coring Y output high frequency component coring gain Hsync slice level Vsync slice level ADC clock delay
0~3 0, 1 0~15 0~15 0~3
1 0 12 8 3
1 0
1 0
NRMD Setting-based Control Table for D2GA
25 D2GA 26 KILR C C
UHF/VHF CVideo1 SVideo1
0~7 0~15 0, 1 0 1 1
4 3
27
OP1
Moving detection gain Killer detection reference Option1: Selection of comb filter & recursive noise reduction types C C C C C
UHF/VHF
0 0 1 1 0 1
Video1~4
This setting continues to the next page.
28 NR1 29 NR2 30 WSL 31 HPLL 32 BPLL 33 FSCF 34 PLLF 0, 1 0~7 0~15 0~15 0, 1 0~3 0 5 4 10 0 1
UHF/VHF & Video1~4
Noise reduction on/off SNNR control on/off Noise level detection data H-PLL filter (Must be set to 1 when MN signal is input.) Burst PLL filter Burst extraction gain PLL loop gain 0
0, 1 0, 1 0~255 0, 1 0, 1 0, 1 0, 1
1 Byte Data from Read Register WSL
Video5&6
Selection of a line-comb filter C separation filter characteristic Fine adjustment of the system H-phase C Internal burst gate start position C 37 BGPS {Gate Start Position from Hsync center = 0.25 x BGPS + 2 Internal burst gate width 38 BGPW C {Gate Width = 0.25 x BGPW + 0.5 (ms)} 39 TEST Test bit {0: Normal mode, 1: Test mode (forbidden setting)} C 40 WSC Amount of noise detection coring C
Micro
35 CC3N 36 HDP
0
Video1~4: CVideo1~4 & SVideo1~3 inputs Video5&6: YPbPr-480i/480p/1080i inputs
Video5&6
41 LIND 42 PFGO
DRC-M line-doubling setting for non-standard signals (YPFG offset at GR on) --- Not used for DX1A
0 --0~63 0~7 3
2 (Not used for DX1A)
This setting is used for non-standard signals such as Play Station signals.
Note: The same 3D-COMB service data is used for DX1A-2001&2000.
DX1A-2001&2000 SERVICE LIST (#1): 3D-COMB / mPD64082 (Part-4/4)
Data Initial/Average Setting
(32V&36V CRTs) CVideo2 SVideo2 CVideo3 SVideo3
Register No & Name
Comment
#28 NR1 (cont.)
0
1
0
1
Note: The same 3D-COMB service data is used for DX1A-2001&2000.
-- 22 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#2-1): CXA2103-1 {Main}
Device Name: CXA2103Q { NTSC-YCT (Chroma Decoder) / SONY } / IC3048 (B-board) / P/N: 8-752-089-50 (SBorSD#: NA) Slave Address: 9Ah { Main }
Data Initial Setting & [Average Data]
(32V&36V CRTs) UHF/VHF & Video
P&P-Left (M)-DRC P&P-Left (M)-1080i P&P-Left (M)-DRC P&P-Left (M)-480i
Data Initial/Average Setting
(32V&36V CRTs)
Register No & Name Control Register Function & Link
YPbPr-480i
Data Type
Data Range
Note
0 1
UHF/VHF Video
YLEV CLEV Adj. Adj. Adj. 0~15 0~15 0~15 0~3
UHF/VHF CVideo SVideo YPbPr 480i SNNR=0 (-offset)
Y-Out gain Cb&Cr-Out gains 7 [7] 7 [7] 7 [Adj.-2steps] 0 0 7 [7] 7 [7] 7 [Adj.-2steps] 0
0~63 0~63
23 17
27* 55*
28 32
31* 31*
Video: CVideo1~4 & SVideo1~3 Inputs P&P-Left (M)-1080i&480i: If P&P-Left is 1080i/480p signal, the signal from the main chroma decoder is sent to MID/VDO input. *: Settings not used
2 3 4 5
SCON SCOL SHUE YDLY
Sub contrast Sub color Sub hue Y/C delay time
Adj.: Adjusted data [Adj.-2steps]: The adjusted data - 2 steps
SNNR Data-related Settings
SNNR=1 (-offset)
SNNR=2 (-offset)
SNNR=3 (-offset)
1
2
3
6 SHAP 7 SHF0 8 PREO 9 BPF0 10 BPFQ 11 BPSW 12 TRAP 13 LPF
UHF/VHF Video YPbPr 480i
Sharpness Sharpness f0 selector Sharpness pre/over-shoot ratio Chroma band filter f0 setting Chroma band filter Q setting Chroma band filter on/off Y bolck chroma trap filter on/off YPbPr-Output LPF on/off 0, 1 0~3 0~3 0, 1 0, 1 0~15
P&P-Left (M)-DRC
0~15 0~3 0~3 0~3 0~3 0, 1 0, 1 0, 1 1 3 0 1 0 7 0 3 0 1 0 7
UHF/VHF & Video
P&P-Left (M)-1080i
6 0 3 3 0 1 0 0 0 3 0 1 0 7
YPbPr-480i
P&P-Left (M)-DRC
4 0 0 0 3 0 0 0
4 0 0 0 3 0 0 0
4 0 0 0 3 0 0 0
CVideo: CVideo1~4 Inputs SVideo: SVideo1~3 Inputs
14 AFCG 15 CDMD 16 SSMD 17 HMSK 18 HALI 19 PPHA
AFC Loop Gain (PLL between Hsync & HVCO) V countdown system mode selector H&Vsync slide level setting Masking of macrovision signal on/off H automatic adjustment on/off H TIM phase adjustment for video
P&P-Left (M)-480i
20 CBOF
0~(31)~63 0~(31)~63
31 31
UBLK = 0
31* 31*
UBLK = 1
31 31
P&P & Favorite
UBLK = 2
31* 31*
UBLK = 3
21 CROF
Cb-Offset1 of Cb IN (Pin34) Cb-Offset2 of EXT Cb (Pin38) Cr-Offset1 of Cr IN (Pin35) Cr-Offset2 of EXT Cr (Pin39)
*: Settings not used (31): The center setting = 31
P&P & Favorite
UBLK = 4 UBLK = 5 UBLK = 6 UBLK = 7
CXA2150P-4/#13 UBLK Setting-related Controls for ATPD & DCTR
Single
UBLK = 0~7
22 23
ATPD DCTR
Auto-pedestal Inflection Point DC Transmission Ratio
0~3 0~3
0 0
1 1
2 1
3 1
1 2
2 2
3 2
2 3
0 0
Note: The same CXA2103 service data (Main&Sub) is used for DX1A-2001&2000.
-- 23 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#2-2): CXA2103-2 {Sub}
Device Name: CXA2103Q { NTSC-YCT (Chroma Decoder) / SONY } / IC3110 (B-board) / P/N: 8-752-089-50 (SBorSD#: NA) Slave Address: 9Eh { Sub }
Data Initial Setting & [Average Data]
(32V&36V CRTs) UHF/VHF & Video
P&P-Right (S) P&P-Right (S)-DRC
Data Initial/Average Setting
(32V&36V CRTs)
Register No & Name Control Register Function & Link Data Type Data Range
Note
0 1
UHF/VHF Video
YLEV CLEV Adj. Adj. Adj. 0~15 0~15 0~15 0~3
UHF/VHF CVideo SVideo SNNR=0 (-offset)
Y-Out gain Cb&Cr-Out gains 7 [7] 7 [7] 7 [Adj.-2steps] 0 0 7 [7] 7 [7] 7 [Adj.-2steps] 0
0~63 0~63
23 18
22 16
Video: CVideo1~4 & SVideo1~3 Inputs P&P-Right (S)-DRC: If P&P-Left is 1080i/ 480p signal, the signal from the sub chroma decoder is switched to DRC path.
2 3 4 5
SCON SCOL SHUE YDLY
Sub contrast Sub color Sub hue Y/C delay time
Adj.: Adjusted data [Adj.-2steps]: The adjusted data - 2 steps
SNNR Data-related Settings
SNNR=1 (-offset)
SNNR=2 (-offset)
SNNR=3 (-offset)
1
2
3
6 SHAP 7 SHF0 8 PREO 9 BPF0 10 BPFQ 11 BPSW 12 TRAP 13 LPF
UHF/VHF Video
Sharpness Sharpness f0 selector Sharpness pre/over-shoot ratio Chroma band filter f0 setting Chroma band filter Q setting Chroma band filter on/off Y bolck chroma trap filter on/off YPbPr-Output LPF on/off 0, 1 0~3 0~3 0, 1 0, 1 0~15
P&P-Right (S)
0~15 0~3 0~3 0~3 0~3 0, 1 0, 1 0, 1 1 3 0 1 0 7 0 3 0 1 0 7
UHF/VHF & CVideo
P&P-Right (S)-DRC
6 0 3 0 0 0 0 0
4 0 0 0 0 0 0 0
4 0 0 0 0 0 0 0
CVideo: CVideo1~4 Inputs SVideo: SVideo1~3 Inputs
14 AFCG 15 CDMD 16 SSMD 17 HMSK 18 HALI 19 PPHA
AFC Loop Gain V countdown system mode selector H&Vsync slide level setting Masking of macrovision signal on/off H automatic adjustment on/off H TIM phase adjustment for video
YPbPr-480i
P&P-Right (S) P&P-Right (S)-DRC
20 CBOF
0~(31)~63 0~(31)~63
31 31
UBLK = 0
31 31
UBLK = 1
31* 31*
P&P & Favorite
UBLK = 2
31* 31*
UBLK = 3
21 CROF
Cb-Offset1 of Cb IN (Pin34) Cb-Offset2 of EXT Cb (Pin38) Cr-Offset1 of Cr IN (Pin35) Cr-Offset2 of EXT Cr (Pin39)
*: Settings not used (31): The center setting = 31
P&P & Favorite
UBLK = 4 UBLK = 5 UBLK = 6 UBLK = 7
CXA2150P-4/#13 UBLK Setting-related Controls for ATPD & DCTR
Single
UBLK = 0~7
22 23
ATPD DCTR
Auto-pedestal Inflection Point DC Transmission Ratio
0~3 0~3
0 0
1 1
2 1
3 1
1 2
2 2
3 2
2 3
0 0
Note: The same CXA2103 service data (Main&Sub) is used for DX1A-2001&2000.
-- 24 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#3-1): CXA2150P-1 {Picture Controls: P1}
Device Name: CXA2150AQ { CRT Driver / SONY } / IC201 (A-board) / P/N: 8-752-093-35 (SBorSD#: NA) Slave Address: 86h
Data Initial Settings & [Average Data]
(32V&36V CRTs) UHF VHF CV SV YPbPr 480i YPbPr 480p YPbPr 1080i P&P
Register No & Name Control Register Function & Link Data Type Data Range
Comment CV: CVideo1~4 SV: SVideo1~3 ( ): Settings at center
7 0 31 31
7 0 31 31
7 0 31 31
7 0 31 31
7 0 13 23
Adj.: Adjusted data C: Common data Initial Setting = [Avg. Data]
Vivid Standard Movie Pro
0 1 2 3 4 5 6 7 8 9 10 Adj. C Adj. Adj. C Adj. Adj. 0, 1 0
(Cool)
SBOT YOF CBOF CROF SBRT RDRV GDRV BDRV RCUT GCUT BCUT
Offset for SBRT Y_OFFSET: DC-offset for Y signal CB_OFFSET: DC-offset for Cb signal CR_OFFSET: DC-offset for Cr signal SUB_BRIGHT: Sub Bright R_DRIVE: R output drive G_DRIVE: G output drive B_DRIVE: B output drive R_CUTOFF: R output cutoff G_CUTOFF: G output cutoff B_CUTOFF: B output cutoff
0~(7)~15 0~(7)~15 0~(31)~63 0~(31)~63 0~63 0~63 0~63 0~63 0~63 0~63 0~63
7 7 0 0 33 30 42 36 24 [24] 41 36 [36] 33 [33] 41 11 [11] 22 [22] 0
(Neutral)
1
(Warm)
0
WB_SW: White balance offset on/off 11 WBSW (Related to UTMP seetings) 12 SBOF Offset for SBRT 13 RDOF Offset for RDRV 14 GDOF Offset for GDRV 15 BDOF Offset for BDRV 16 RCOF Offset for RCUT 17 GCOF Offset for GCUT 18 BCOF Offset for BCUT
0~(63)~127 0~(63)~127 0~(63)~127 0~(63)~127 0~(63)~127 0~(63)~127 0~(63)~127
63 63 63 63 63 63 63
63 63 63 63 63 63 63
63 63** 66** 76** 63** 66** 78**
63 63 63 63 63 63 63
**: The color temporature offset data
Note: The same CXA2150 service data is used for DX1A-2001&2000.
-- 25 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#3-2): CXA2150P-2 {Picture Controls: P2}
Device Name: CXA2150AQ { CRT Driver / SONY } / IC201 (A-board) / P/N: 8-752-093-35 (SBorSD#: NA) Slave Address: 86h
Data Initial/Average Settings
(32V&36V CRTs)
Register No & Name Control Register Function & Link Data Type Data Range
Comment
0 C C C C C C C 0 15 0 0 0
U/VHF & Video1~4
ALBK 0~7 0~3 3 7
C
0, 1
1
1
RGBS
2
BLKB
3 4 5
LIML PABL SABL
C: Common data
6
AGNG
7
AKBO
PIC_ON: RGB output including AKB reference pulse on/off (Setting = 0 for power on reset) --- G2 adjustment register setting R_ON/G_ON/B_ON: R/G/B outputs on/off (AKB reference pusle can not be turned on/off.) (0,1/0,1/0,1) BLK_BTM: RGB output bottom limit level (Black Limit) (AKB reference pusle DC-voltage) PLIMIT_LEV: Threshold level for excessively high inputs (White Limit) P_ABL: DC-level in RGB output detection for PEAK ABL S_ABL: S_ABL gain AGING_W/AGING_B: AGING_W/AGING_B modes on/off (Set luminance to 80/01IRE flat-field signal.) AKBOFF: Automatic/Manual-Cutoff setting 0~3 0~15 0~3 0~3 (0,1/0,1) 0, 1 0~3 0~3 0, 1 0, 1 0, 1 0 3 0 0 0
YPbPr 480i
YPbPr 480p
YPbPr 1080i
P&P
8 9 10 11 12
SYPH CLPH CLGA JAXS BLKO
SYNC_PHASE: Hsync delay with respect to Video (100%: H-period) CLP_PHASE: Internal clamp pulse phase (100%: H-period) CLP_GATE: Switch for the gated internal clamp pulse with Hsync input JAXIS: Color axis switch BLKO: Blanking switch
0 3 0
0 3 0
0 3 0
0 3 0
Video1~4: CVideo1~4 & SVideo1~3
Note: The same CXA2150 service data is used for DX1A-2001&2000.
-- 26 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#3-3): CXA2150P-3 {Picture Controls: P3} (Part-1/3)
Device Name: CXA2150AQ { CRT Driver / SONY } / IC201 (A-board) / P/N: 8-752-093-35 (SBorSD#: NA) Slave Address: 86h
Data Initial/Average Settings (32V&36V CRTs) Control Register Function & Link
UHF VHF CV SV
Register No & Name Data Type
Data Range
Picture Mode: Vivid
YPbPr 480i YPbPr 480p YPbPr 1080i P&P
Comment
1
1
1
1
2
2
These settings continue to the next page. CV: CVideo1~4 SV: SVideo1~3 C: Common data ( ): Settings at center
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 0 3 3 2 3 2 1 3 3 3 3 0 0 0 7 3 0 3
SYSM UVML VMMO VMCR VMLM VMF0 VMDL SHOF SHF0 PROV F1LV CDSP LTLV LTMD CTLV CTMD UBOF UCOF UHOF MIDE
SYSTEM: Signal bandwidth setting C VM_LEV: VM_OUT level System Micro pin#40 VM_COR: VM_OUT coring level VM_LMT: VM_OUT limit level VM_F0: VM_f0 VM_DLY: VM_OUT phase (defined by phase difference from R_OUT) Offset for USHP = SHOF x 4 SHP_F0: Sharpness circuit f0 PRE/OVER: Y signal pre/over-shoot ratio SHP_F1: Sharpness for higher f0 (4.2/5.6 MHz @ NORMAL mode) SHP_CD: Sharpness in part of high color saturaion LTI_LEV: Luminance transient improvement (LTI) LTI_MODE: LTI mode setting CTI_LEV: Chrominance transient improvement (CTI) CTI_MODE: CTI mode setting Offset for UBRT (Picture clarity adjustment) Offset for UCOL = UCOF x 2 (Picture clarity adjustment) Offset for UHUE (Picture clarity adjustment) MID enhancement setting
0~3 0~3 0, 1 0~3 0~3 0~3 0~3 0~3 0, 1 0~3 0~3 0~3 0~3 0~3 0~3 0~3 0~(7)~15 0~3 0~3 0~15
1 3 0 3 3 2 3 2 1 3 0 3 3 0 0 0 7 3 0 3
0 3 3 2 3 2 1 3 3 3 3 0 0 0 7 3 0 3
0 3 3 2 3 3 1 1 3 3 3 0 0 0 7 3 0 7
0 3 3 2 3 3 1 3 3 3 3 0 0 0 7 3 0 11
0 3 3 2 1 0 0 0 3 3 3 0 2 0 10 0 0 ---
0 3 3 2 3 2 1 3 3 3 3 1 0 0 7 3 0 ---
Note: The same CXA2150 service data are used for DX1A-2001&2000.
-- 27 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#3-3): CXA2150P-3 {Picture Controls: P3} (Part-2/3)
Data Initial/Average Settings (32V&36V CRTs)
Picture Mode: Standard
CV SV YPbPr 480i P&P CV SV P&P CV SV YPbPr 480p YPbPr 1080i UHF VHF YPbPr 480i YPbPr 480p YPbPr 1080i UHF VHF YPbPr 480i YPbPr 480p
Data Initial/Average Settings (32V&36V CRTs)
Picture Mode: Movie Picture Mode: Pro
Data Initial/Average Settings (32V&36V CRTs) Note
YPbPr 1080i P&P
Register No & Name
UHF VHF
1
1
1
1
2
2
1
1
1
1
2
2
1
1
1
1
2
2
#0 SYSM (cont.) #1 UVML (cont.) #2 VMMO (cont.) #3 VMCR (cont.) #4 VMLM (cont.) #5 VMF0 (cont.) #6 VMDL (cont.) #7 SHOF (cont.) #8 SHF0 (cont.) #9 PROV (cont.) #10 F1LV (cont.) #11 CDSP (cont.) #12 LTLV (cont.) #13 LTMD (cont.) #14 CTLV (cont.) #15 CTMD (cont.) #16 UBOF (cont.) #17 UCOF (cont.) #18 UHOF (cont.) #19 MIDE (cont.) 0 3 3 2 3 3 1 3 3 3 2 1 0 0 7 3 0 2 0 3 3 2 3 3 1 3 3 3 2 1 0 0 7 3 0 2 0 3 3 2 3 3 1 1 3 3 2 1 0 0 7 3 0 6 0 3 3 2 3 3 1 3 3 3 2 1 0 0 7 3 0 10 0 3 3 2 1 0 0 0 3 3 2 1 2 0 7 0 0 --0 3 3 2 3 2 1 3 3 3 3 1 0 0 7 3 0 --0 3 3 2 1 3 0 3 0 0 0 1 0 0 7 0 0 1 0 3 3 2 1 3 0 3 0 0 0 1 0 0 7 0 0 1 0 3 3 2 1 3 0 1 0 0 0 1 0 0 7 0 0 5 0 3 3 2 1 3 0 3 0 0 0 0 0 0 7 0 0 9 0 3 3 2 1 0 0 0 0 0 0 0 0 0 7 0 0 --0 3 3 2 3 3 1 3 3 0 0 1 0 0 7 0 0 --0 3 3 2 1 1 0 3 0 0 0 1 0 0 7 0 0 0 0 3 3 2 1 1 0 3 0 0 0 1 0 0 7 0 0 0 0 3 3 2 1 1 0 1 0 0 0 1 0 0 7 0 0 4
1 3 0 3 3 2 1 0 0 3 0 3 2 1 0 0 7 3 0 2
1 0 0 3 3 2 1 0 0 3 0 0 0 1 0 0 7 0 0 1
1 0 0 3 3 2 1 0 0 3 0 0 0 1 0 0 7 0 0 0
0 3 3 2 1 1 0 3 0 0 0 0 0 0 7 0 0 8
0 3 3 2 1 0 0 0 0 0 0 0 0 0 7 0 0 ---
0 3 3 2 3 1 1 3 3 0 0 1 0 0 7 0 0 ---
See next page
Note: The same CXA2150 service data are used for DX1A-2001&2000.
DX1A-2001&2000 SERVICE LIST (#3-3): CXA2150P-3 {Picture Controls: P3} (Part-3/3)
Data Initial/Average Settings (32V&36V CRTs)
SNNR=1 (Offset) SNNR=2 (Offset) SNNR=3 (Offset)
Register No & Name
SNNR=0 (Offset)
Comment
#1 UVML (cont.) #3 VMCR (cont.) #10 F1LV (cont.) #11 CDSP (cont.) #12 LTLV (cont.) #14 CTLV (cont.) #19 MIDE (cont.)
0 0 0 0 0 0 0
0 +1 -1 0 0 0 0
0 +2 -2 0 0 0 0
0 +3 -3 0 0 0 0
Note: The same CXA2150 service data are used for DX1A-2001&2000.
-- 28 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#3-4): CXA2150P-4 {Picture Controls: P4} (Part-1/4)
Device Name: Device Name:
Data Initial/Average Settings
(32V&36V CRTs) Vivid Standard
36V 32V 36V 32V
CXA2150AQ { CRT Driver / SONY } / IC201 (A-board) / P/N: 8-752-093-35 (SBorSD#: NA) Slave Address: 86h CXD2085M { ID-1 Decoder / SONY } / IC3603 (B-board) / P/N: 8-752-395-13 (SD#: S98511B) Slave Address: 40h
Control Register Function & Link
Movie
32&36V
Register No & Name Data Type Data Range
Comment
Pro
0 1 2 3 63 25 34 31 38 2 2
UHF/VHF Video1~4 YPbPr 480i
UPIC UBRT UCOL UHUE 42 28 33 31 44 1 2 48 1 2
YPbPr 480p YPbPr 1080i
PICTURE: Picture BRIGHT: Brightness COLOR: Color HUE: Hue 0~63 0~2 0~3 42 2 2
0~63 0~63 0~63 0~63
63 22 38 31
46 26 33 31
31 28 33 31 34 0 2
P&P
31 31 31 31 31 1 0
Settings for 36V CRTs are used for initial settings. This setting continues to the next page.
SNNR Setting-related Controls for USHP
4 5 6
USHP UTMP UDCL
SHARPNESS: Sharpness Color Temporature (0: Warm, 1: Neutral, 2: Cool) DCOL: Dynamic color setting
Picture Mode: Vivid / Standard / Movie
7
AXIS
COL_AXIS: Color matrix setting
0~3
3
UHF/VHF Video1~4
3
YPbPr 480i
3
YPbPr 480p
3
Picture Mode: Vivid
YPbPr 1080i
3
P&P
These settings continue to the next page. Video1~4: CVideo1~4 & SVideo1~3
8
UGAM
GAMMA/GAMMA_L: RGB output GAMMA correction setting (B 7~6) GAMMA_L: Slight GAMMA correction on/off (B 0)
5 --UGAM =7 UGAM =6
5
5
5
5
9
AGAM GAMMA/GAMMA_L (Av Pro user control) --- Void Data
0~7 (0~3/0,1) 0~7 (0~3/0,1) 0~3 0~3 0~3
UGAM Setting-related Controls for GSBO, GCOO, GHUO
UGAM =5
UGAM =4
UGAM =3
UGAM =2
UGAM =1
10 GSBO 11 GCOO 12 GHUO
Offset for SBRT (8 types of GSBO data based on UGAM values) Offset for UCOL Offset for UHUE
0 0 0
0 0 0
UHF/VHF Video1~4
0 0 0
YPbPr 480i
0 0 0
YPbPr 480p
0 0 0
Picture Mode: Vivid
YPbPr 1080i
0 0 0
P&P
0 0 0
These settings continue to the next page.
13 UBLK 14 ABLK
Item # 15~18 pack FI data controls (Av Pro user control) --- Void Data
---
0~7 0~7 0~3 0~3 0~(7)~15 0~3
7 0 (Void data) 3 2 7 1
7
7
7
7
UBLK Setting-related Controls for DCTR
15 DCTR
3 2 7 1
3 2 7 1
3 2 7 1
2 1 7 1
16 DPIC 17 DSBO 18 ABLM
DC_TRAN: Y signal DC transmission (8 types of DCTR data based on UBLK values) DPIC_LEV: Y signal AUTO PEDESTAL level Offset for SBRT ABL_MODE: ABL mode
These settings continue to the next page. ( ): Seetings at center
Note: The same CXA2150 service data are used for DX1A-2001&2000.
-- 29 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#3-4): CXA2150P-4 {Picture Controls: P4} (Part-2/4)
Data Initial/Average Settings
(32V&36V CRTs) (32V&36V CRTs) (32V&36V CRTs)
Register No & Name
Data Initial/Average Settings
Data Initial/Average Settings
Note
SNNR Setting (-Offset)
SNNR =2 SNNR =3
SNNR =0
SNNR =1
#4 USHP (cont.)
0
1
3
4
Picture Mode: Pro
YPbPr 480i P&P YPbPr 480p YPbPr 1080i
UHF/VHF Video1~4
#7 AXIS (Cont.)
Picture Mode: Standard Picture Mode: Movie
P&P U/VHF Video1~4 YPbPr 480i YPbPr 480p YPbPr 1080i P&P YPbPr 480i YPbPr 480p YPbPr 1080i
3 3 3 3 3
Picture Mode: Pro
U/VHF Video1~4 YPbPr 480i YPbPr 480p YPbPr 1080i P&P
U/VHF Video1~4
#8 UGAM (Cont.)
2 2 2 2 0 0 0
2 0
0
0
0
0
0
0
UGAM
=0
#10 GSBO (cont.) #11 GCOO (cont.) #12 GHUO (cont.)
Picture Mode: Standard
YPbPr 480i P&P YPbPr 480p YPbPr 1080i UHF/VHF Video1~4 YPbPr 480i
0 0 0
Picture Mode: Movie
YPbPr 480p YPbPr 1080i P&P UHF/VHF Video1~4
Picture Mode: Pro
YPbPr 480i YPbPr 480p YPbPr 1080i P&P
UHF/VHF Video1~4
#13 UBLK (Cont.)
4 4 4 4
4
1
1
1
1
1
0
0
0
0
0
#15 DCTR (Cont.) 1 7 1 1 7 1 1 7 1 1 7 1
2 2 2 2
2
1 1 7 0
1 1 7 0
1 1 7 0
1 1 7 0
1 1 7 0
1 0 7 0
1 0 7 0
1 0 7 0
1 0 7 0
1 0 7 0
#16 DPIC (Cont.) #17 DSBO (Cont.) #18 ABLM (Cont.)
1 7 1
See next pages
Note: The same CXA2150 service data are used for DX1A-2001&2000.
-- 30 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#3-4): CXA2150P-4 {Picture Controls: P4} (Part-3/4)
Data Initial/Average Settings
(32V&36V CRTs) UBLK = 6 UBLK = 5 UBLK = 4 UBLK = 3 UBLK = 2 UBLK = 1 UBLK = 0
Register No & Name Comment
UBLK = 7
#15 DCTR (Cont.) 2 7 1 3 7 0 2 7 0 1 7 1 3 7 0 2 7 0 1 7 0 0 7 0
3
2
2
2
1
1
1
1
#16 DPIC (Cont.) #17 DSBO (Cont.) #18 ABLM (Cont.)
Note: The same CXA2150 service data are used for DX1A-2001&2000.
DX1A-2001&2000 SERVICE LIST (#3-4): CXA2150P-4 {Picture Controls: P4} (Part-4/4)
Data Initial/Average Settings
(32V&36V CRTs)
Register No & Name Control Register Function & Link Data Type Data Range
Comment
19
ABLT
ABL_TH: ABL currect detection Vth control
0~15
0
Full Vcomp1 Vcomp2
0 0~255 0~31
66
20 ABLC 21 EPOF -----
Control of CXA2026 {0Ch -- DAC0} (*) Offset for UPIC = EPOF x (UPIC/63) (for power save) --- Void Data
ID-1 and P&P Modes
22 SPOF
Offset for UPIC = SPOF x (UPIC/64) --- Data Not Used
0~31 0~15 0~(7)~15 0~7~15 C C 0, 1 0~3
0 (Not used)
UHF/VHF Video1~4
YPbPr 480i YPbPr 480p YPbPr 1080i P&P
23 SCON 24 CLOF 25 HUOF
SUB_CONTRAST: SUB PICTURE Offset for UCOL Offset for UHUE
9 8 4 0
Full
8 8 3
11 9 3
10 7 3
9 8 4
Full: 480p/960i (4x3) Vcomp1: 480p/960i (16x9) Vcomp2: 1080i (16x9)
CXD2085 Service Controls
Vcomp1 Vcomp2
26
IDSW
Switch for activating the selection in #27 DATA
27
DATA
Selection of geometry-forced vertical compression modes
0
1
2
( ): Settings at center C: Common data
Note: The same CXA2150 service data are used for DX1A-2001&2000.
-- 31 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#4-1): CXA2150D-1 {Deflection Controls: D1}
Device Name: CXA2150AQ { CRT Driver / SONY } / IC201 (A-board) / P/N: 8-752-093-35 (SBorSD#: NA) Slave Address: 86h
Control Register Function & Link
Full Vcomp1
Register No & Name Data Type Data Range
Data Initial Settings & [Average Data] (32V&36V CRTs)
Vcomp2
Comment Full: 480p/960i (4x3) display Vcomp1: 480p/960i (16x9) display Vcomp2: 1080i (16x9) display Adj.: Adjusted data ( ): Settings at center
0 1 Adj. Adj. Adj. 0~(31)~63 Adj. 0~(15)~31 Adj. 0~(7)~15 15 [15] 0~(7)~15 0~(7)~15 9 [9] 8 [8] 31 [31]
VPOS VSIZ
Adj. 0~(31)~63 Adj. 0~(31)~63
26 [26] 19 [19]
2
VLIN
3
VSCO
4
VCEN
VCEN-L(Low bit) VCEN-H(High bit)
5
VPIN
V_POSITION: Vertical position (V_DRV siganl DC-bias) V_SIZE: Vertical size (V_DRV signal gain) V_LINEARITY: Vertical linearity (Gain for V_DRV signal secondary component) S_CORRECTION: Vertical S-correction VSAW0_DCH/VSAW0_DCL: Vertical center adjustment VSAW0_DCH: VSAW0 waveform DC component (high 2-bits) VSAW0_DCL: VSAW0 waveform DC component (low 4-bits) VSAW0_AMP: Vertical PIN adjustment VSAW0 waveform SAW component amplitude 7 [7] 15 [15]
15 [Copty1]
[Copy1]: Copy the adjusted data for Full mode.
6
NSCO
VSAW1_DC: Rotation
0 1 47 32 0 0 0 1 47 31 0 0 0 47 32
7 HTPZ 8 ZOOM 9 APSW 10 ASPT 11 SCRL 12 UVLN 13 LVLN
VSAW1_AMP: Horizontal trapezoid ZOOM_SW: Zoom switch ASP_SW: Aspect switch V_ASPECT: Aspect ratio V_SCROLL: Vertical scroll UP_VLIN: Upper vertical linearity LO_VLIN: Lower vertical linearity
Adj. 0~(15)~31 0, 1 0, 1 Adj. 0~63 Adj. 0~(31)~63 0~15 0~15
Either 7 or 8 can be used as the average NSCO data. (If both of them are not good, please feedback to / check with the DY attachment process.)
Note: The same CXA2150 service data is used for DX1A-2001&2000.
-- 32 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#4-2): CXA2150D-2 {Deflection Controls: D2}
Device Name: CXA2150AQ { CRT Driver / SONY } / IC201 (A-board) / P/N: 8-752-093-35 (SBorSD#: NA) Slave Address: 86h
Data Initial Settings & [Average Data]
(32V&36V CRTs) Full Vcomp1 Vcomp2
Register No & Name Control Register Function & Link Data Type Data Range
Comment
0 Adj. 0~(31)~63 31 [31]
HCNT
HC_PARA_DC: Horizontal center
Adj. 0~(31)~63
31 [31] 31 [Adj.-6steps]
1
HPOS
H_POSITION: Horizontal position
Full: 480p/960i (4x3) display Vcomp1: 480p/960i (16x9) display Vcomp2: 1080i (16x9) display ( ): Settings at center Adj.: Adjusted data [Adj.-6steps]: The adj. data for Vcomp2 mode = The adj. data for Full/Vcomp1 modes - 6 steps Data (32Vor36V): The data for 36V are used as the Initial & CBA data. From the system micro (V 2.0), the deflection control-related initial settings are the same as their average data.
2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
Micro
HSIZ SLIN MPIN PIN UCP LCP UXCG LXCG UXCP LXCP XCPP PPHA VANG LANG VBOW LBOW 0, 1
Adj. 0~(31)~63 Adj. 0~15 0~15 Adj. 0~(31)~63 Adj. 0~(31)~63 Adj. 0~(31)~63 0~3 0~3 0~3 0~3 0, 1 Adj. 0~(31)~63 Adj. 0~(31)~63 Adj. 0~(31)~63 Adj. 0~(31)~63 Adj. 0~(31)~63
45 [45] 3 [3] 9 (32V) or 7 (36V) 35 [35] 38 [38] 42 [42] 2 (32V) or 1 (36V) 2 2 2 0 15 [15] 31 [31] 31 [31] 31 [31] 31 [31] 0
18
CPY1
H_SIZE: Horizontal size MP_PARA_DC: Horizontal S-correction MP_PARA_AMP: Horizontal middle pin PIN_AMP: Horizontal pin UP_CPIN: Upper corner pin LO_CPIN: Lower corner pin UP_UCG: Upper extra corner pin gain LO_UCG: Lower extra corner pin gain UP_UCP: Upper extra corner pin position LO_UCP: Lower extra corner pin postion UC_POL: Extra corner pin polarity PIN_PHASE: Pin phase AFC_ANGLE: AFC angle HC_PARA_PHASE: Linearity angle AFC_BOW: AFC bow HC_PARA_AMP: Linearity bow Copy Function 1: (Set CPY1=1, then press MUTE + Enter.) Copy all CXA2150D-2 data for Full mode to Vcomp1&2
For engineering design use only
Note: The same CXA2150 service data is used for DX1A-2001&2000.
-- 33 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#4-3): CXA2150D-3 {Deflection Controls: D3}
Device Name: CXA2150AQ { CRT Driver / SONY } / IC201 (A-board) / P/N: 8-752-093-35 (SBorSD#: NA) Slave Address: 86h
Data Initial/Average Settings
(32V&36V CRTs) Full Vcomp1 Vcomp2
Register No & Name Control Register Function & Link Data Type Data Range
Comment
1 45 24 1 8 13 0 0 0 0 3 1 1 1 0 0 0 20 10 0 0 0 0 20 1 1 2 12 13 0 1 1 0 0 0 0 0 50 27
Full: 480p/960i (4x3) display Vcomp1: 480p/960i (16x9) display Vcomp2: 1080i (16x9) display
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
HBLK LBLK RBLK VBLK TBLK BBLK VCMP HCMP ACMP PCMP AFCM VFRQ VON JUMP VDJP VDST EWDC AKBT
HBLK_SW: Horizontal blanking switch LEFT_BLK: Left blanking RIGHT_BLK: Right blanking VBLK_SW: Vertical blanking switch UP_BLK: Top blanking LO_BLK: Bottom blanking V_COMP: Vertical compensation H_COMP: Horizontal compensation AFC_COMP: AFC compensation PIN_COMP: Pin compensation AFC_MODE: AFC loop gain V_FREQ: Vertical frequency V_ON: Vertical drive on JMP_SW: Reference pulse jump swtich VDRV_SW: Vertical drive jump switch RST_SW: Vertical drive start switch EW_DC: Pin DC level shift AKBTIM: AKB timing
0, 1 0~63 0~63 0, 1 0~(7)~15 0~(7)~15 0~15 0~15 0~7 0~7 0~3 0~3 0, 1 0, 1 0, 1 0, 1 0, 1 0~31
( ): Settings at center
Note: The same CXA2150 service data is used for DX1A-2001&2000.
-- 34 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#5): CXA2151Q
Device Name: CXA2151Q { Component I/F & Sync Seperation / SONY } / IC3001 (B-board) / P/N: 8-752-093-84 (SD#: S00302B) Slave Address: 84h
Control Register Function & Link
480i (15.75 KHz) 480p (31.50 KHz)
Register No & Name Data Type Data Range
Data Initial/Average Settings (32V&36V CRTs)
1080i (33.75 KHz)
Comment
0
Micro
MTRX C C C C 0~3 0~3 1 1
Video5
0~3 0~3 0~15 9 0
0
0
1
Video5&6: YPbPr-480i/480p/1080i inputs Sub: 480i input from the sub-channel
1
GAIN
2
CBGN
Full: 480p/960i (4x3) display Vcomp1: 480p/960i (16x9) display Vcomp2: 1080i (16x9) display C: Common data
Video6 Sub
3 4
VTC HWID
MAT_OUT: Selection of color matrix conversion types GAIN_SEL: Selection of output signals for SELYOUT, SELCBOUT, SELCROUT YGAIN, CBGAIN, CRGAIN: The gain control of SELYOUT, SELCBOUT, & SELCROUT V_TC: Setting of Vsync separation time constant H_WIDTH: Setting of the output pulsewidth of SELHOUT
5 6 C C 0, 1 0, 1
HSEP TEST
0, 1 0, 1
0 0 0
Full
0
0
7
FRGB
HSEP_SEL: Setting for the sync separation system TEST: Test mode selection (for device tests) The forced RGB selection (for tests) {0: MAT_OUT = MTRX (#0), 1: MAT_OUT = MTRX (#3)}
Vcomp1
Vcomp2
8
HMSK
Hsync masking in vertical retrace
1
0
Note: The same CXA2151 service data is used for DX1A-2001&2000.
-- 35 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#6): D-CONV / CXA8070
Device Name: CXA8070AP { DY-Convergence Control / SONY } / IC5513 (D-board) / P/N: 8-759-595-52 (SB#: V1718) Slave Address: DEh
Control Register Function & Link
Full Vcomp1
Register No & Name Data Type Data Range
Data Initial Settings & [Average Data] (32V&36V CRTs)
Vcomp2
Comment
Full: 480p/960i (4x3) display mode Vcomp1: 480p/960i (16x9) display mode Vcomp2: 1080i (16x9) display mode Adj.: Adjusted data From the system micro (V 2.0), the deflection control-related initial settings are the same as their average data.
0 1 2 3 4 5 6 7 8 9
Micro
SBHS YBWU YBWL RSAP RUBW RLBW LSAP LUBW LLBW CADJ 0, 1 0
Adj. Adj. Adj. Adj. Adj. Adj. Adj. Adj. Adj. Adj.
0~63 0~63 0~63 0~63 0~63 0~63 0~63 0~63 0~63 0~63
31 31 31 31 31 31 31 31 31
[31] [31] [31] [31] [31] [31] [31] [31] [31]
31 31 31 31 31 31 31 31 31 48 [48]
[31] [31] [31] [31] [31] [31] [31] [31] [31]
10
CPY2
DC AMP3: DC shift VCA9: Upper Y-bow VCA10: Lower Y-bow DC AMP2: Right H-AMP VCA5: Right upper bow VCA6: Right lower bow DC AMP1: Left H-AMP VCA1: Left upper bow VCA2: Left lower bow DC AMP4: Offset adjustment (ADJ) Copy Function 2: (Set CPY2=1, then press MUTE + Enter.)
For engineering design use only
Note: The same CXA8070 service data is used for DX1A-2001&2000.
-- 36 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#7): CXA2026AS
Device Name: CXA2026AS { DQP Control / SONY } / IC5511 (D-board) / P/N: 8-752-074-64 (SD#: S95610B) Slave Address: 8Eh
Data Initial Settings & [Average Data]
(32V&36V CRTs) Full Vcomp1 Vcomp2
Register No & Name Control Register Function & Link Data Type Data Range
Comment Full: 480p/960i (4x3) display mode Vcomp1: 480p/960i (16x9) display mode Vcomp2: 1080i (16x9) display mode C: Common data Adj.: Adjusted data U.CBOW = QPDV + DVS L.CBOW = QPDV - DVS
0 1 2 3 4 5 6 Adj. 0~63 0~7 0, 1
Micro
DFON DQP DF DQPD QPDV DVS QPDY 0~63
SW0: DF on/off switch PWM: DQP phase DAC1: DF phase H.AMP: DQP dc-level U.CBOW, L.CBOW: DQP dc-level vertical modulation U.CBOW, L.CBOW: DQP dc-level tilt U.MBH,L.MBH: DQP dc-level at top & bottom areas
C Adj. Adj. Adj.
0, 1 0~63 0~63 0~63 0~63 0~(3)~7 0~63
(32V)
7
DQPA
DC SHIFT: DQP amplitude
(36V)
8 QPAV 9 AVS 10 NORM 0, 1 0~63
0 23 [23] 23 [23] 25 [25] 25 [25] 34 [34] 34 [34] 51 47 0 0 7 7 22 [27] (32V) 22 [27] (32V) 22 [27] or or or 13 [15] (36V) 13 [15] (36V) 13 [15] 38 34 3 3 0 0 0 31 [31]
( ): Settings at center Data (36V) are used as Initial/CBA data. From the system micro (V 2.0), most deflection control-related initial settings are the same as their average data. U.YBOW = QPAV + AVS L.YBOW = QPAV - AVS
11 Adj.
CPY3
For engineering design use only
12
200V
U.YBOW, LYBOW: DQP amplitude vertical modulation U.YBOW, LYBOW: DQP amplitude tilt SW1: Copy Function 3: (Set CPY3=1, then press MUTE + Enter.) H.DUTY, H.TILT: 200V regulator adjustment
Note: The same CXA2026 service data is used for DX1A-2001&2000.
-- 37 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#8): Audio Processing (AP) / BH3868AFS
Device Name: BH3868AFS { Audio Processor / ROHM } / IC7001 (A-board) / P/N: 8-759-678-92 (SBorSD#: NA) Slave Address: 82h
Data Initial/Average Setting
(32V&36V CRTs)
Register No & Name Data Type Comment Data Range
Control Register Function & Link
0 1 2 3 4 5 6 7 8
( ): Settings at center
SVOL SBAL SBAS STRE BBLP BBHP SREF AGC BBE
Volume: Offset for Volume Balance: Offset for Balance Bass: Offset for Bass Treble: Offset for Treble BBE lowpass filter BBE highpass filter Surround effect Auto gain control BBE on/off
0~3 0~(3)~7 0~(3)~7 0~(3)~7 0~15 0~15 0~7 0, 1 0, 1
0 7 7 7 0 2 11 0 1
Note: The same AP service data is used for DX1A-2001&2000.
DX1A-2001&2000 SERVICE LIST (#9): TruSurround (TRUS) / NJM2180
Device Name: NJM2180M { TruSurround 3D-Audio Processor / JRC } / IC4101 (S-board) / P/N: 8-759-686-15 (SB#: V9072) Device Control: Controlled via CXA1315M (Audio Control D/A, IC4103/S-board, Slave Address: 48h) / P/N: 8-752-059-23 (SD#: S88Z45B)
Data Initial/Average Setting
(32V&36V CRTs)
Register No & Name Data Type Data Range
Control Register Function & Link
Comment
0 C 0~255
TS
TruSurround effect selection
0~3
2 0
C: Common data DMY1 is used to fulfil the minimum requirement of 2 control items in each service control category.
1
DMY1
Dummy data (No functions)
Note: The same TRUS service data is used for DX1A-2001&2000.
-- 38 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001* SERVICE LIST (#10): MID1 (Common Data)
Device Name: CXD9509AQ { MID-XA / Fujitsu & SONY } / IC3408 (B-board) / P/N: 8-759-672-57 (SBorSD#: NA) Slave Address: 2Eh { Controlled through MID-XA Micro (IC3090/B-board, Slave Address: 64h) / P/N: 6-800-050-01 (SB#: V4216) } MID-XA Micro (MASK type): MB94918RPF-G-137-BND, MID-XA Software: Version 12/08/00, (P/N: 6-800-050-01)
Data Initial/Average Setting
(32V/36V/40V CRTs) MID Mode: All (Single & P&P & Favorite)
Register No & Name Register Name (Software) Data Type Data Range
Control Register Function & Link
Comment
0 1 2 3 4 5 6 7
MID Mode: Signle & Favorite
Single 480i&p Single 1080i Favorite
DHPH DVPH DHAR DVAR DHPW DVPW DYCD DYSD
Horizontal phase of the active display area d_h_phase Vertical phase of the active display area d_v_phase Horizontal size of the active display area d_h_area Vertical size of the active display area d_v_area Horizontal pulse width d_h_pwidth Vertical pulse width d_v_pwidth Delay of YC signal output d_yc_delay Delay of YS signal output d_ys_delay
C C C C C C C C 0~255 0~63 0~255 0~255 0~63 0~7 0~63 0~7
91 20 240 135 27 7 2 1
C: Common data
33 32 230 120 135 54 31
MID Mode: Favorite
8 9 10 11 0~255 0~255 s_dsp_hpos s_dsp_vpos s_dsp_hsiz s_dsp_vsiz dsp_pll_sw C C 0~255 0~255 0~255 0~255 0, 1 0, 1
MDHP MDVP MDHS MDVS
Horizontal position of the main picture Vertical position of the main picture Horizontal size of the main picture Vertical size of the main picture
m_dsp_hpos m_dsp_vpos m_dsp_hsiz m_dsp_vsiz
0~255 0~255 0~255 0~255
8
12 14 158 106
MID Mode: P&P & Favorite
12 MLHP (Horizontal position of the multi pictures) 13 MLVP (Vertical position of the multi pictures)
14 15 16 17
SDHP SDVP SDHS SDVS
Horizontal position of the sub picture Vertical position of the sub picture Horizontal size of the sub picture Vertical size of the sub picture
172 14 61 41
MID Mode: All (Single & P&P & Favorite)
18 DPSW Switch of display output PLL 19 MDL0 Model selection 0 (0: 16x9, 1: 4x3)
0 0
0: MUST be used in DX1A-2001, 1: Used in DX1A-2000
Note: * These MID1 settings are used for DX1A-2001 ONLY. The DPSW setting was changed from 1 in DX1A-2000 to 0 in DX1A-2001.
-- 39 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#11): MID2 (DRC-in Data)
Device Name: CXD9509AQ { MID-XA / Fujitsu & SONY } / IC3408 (B-board) / P/N: 8-759-672-57 (SBorSD#: NA) Slave Address: 2Eh { Controlled through MID-XA Micro (IC3090/B-board, Slave Address: 64h) / P/N: 6-800-050-01 (SB#: V4216) } MID-XA Micro (MASK type): MB94918RPF-G-137-BND, MID-XA Software: Version 12/08/00, (P/N: 6-800-050-01)
Data Initial/Average Setting
(32V&36V CRTs) MID Mode: Single
YC 480i YPbPr 480i YC 480i YPbPr 480i
Register No & Name Control Register Function & Link
MID Mode: P&P & Favorite
YC 480i-(R)
Register Name (Software)
Data Type
Data Range
MID Mode: Freeze
YC 480i YPbPr 480i
0 1 2 3
DRHP DRHS DRVP DRVS
Horizontal position of the active display area (DRC-in Hsize of the active display area (DRC-in) Vposition of the active display area (DRC-in) Vertical size of the active display area (DRC-in)
drc_hactv_pos drc_hactv_siz drc_vactv_pos drc_vactv_siz
0~255 0~255 0~63 0~255
120 174 38 120
116 174 38 120
131 167 53 112
129 167 53 112
137 168 53 112
138 165 53 112
136 165 53 112
Note: The same MID2 service data is used for DX1A-2001&2000.
DX1A-2001&2000 SERVICE LIST (#12): MID3 (VDO-in Data) (Part-1/2)
Device Name: CXD9509AQ { MID-XA / Fujitsu & SONY } / IC3408 (B-board) / P/N: 8-759-672-57 (SBorSD#: NA) Slave Address: 2Eh { Controlled through MID-XA Micro (IC3090/B-board, Slave Address: 64h) / P/N: 6-800-050-01 (SB#: V4216) } MID-XA Micro (MASK type): MB94918RPF-G-137-BND, MID-XA Software: Version 12/08/00, (P/N: 6-800-050-01)
Data Initial/Average Setting
(32V&36V CRTs) MID Mode: Single
YPbPr 480P Dummy 480i
Register No & Name Control Register Function & Link Register Name (Software) Data Type
Data Range
Comment
Dummy-480i settings are used for No Signal cases.
0 1 2 3
VDHP VDHS VDVE VDVS
Horizontal position of the active display area (VDO-in) Horizontal pixel size of the active display area (VDO-in) Vertical even position of the active display area (VDO-in) Vertical line size of the active display area (VDO-in)
vdo_hactv_pos vdo_hactv_pos vdo_vactv_evn vdo_vactv_pos vdo_vactv_odd vdo_clp_pos vdo_clp_wdt vdo_yc_delay vdo_pll_stop vdo_pll_strt vdo_hsync_cyc
0~255 0~255 0~63 0~255
YC 480i
122 159 39 129
YPbPr 480P YPbPr 1080i
179 199 24 56
Dummy 480i
These settings continue to the next page.
4 5 6 7
VDVO VCPO VCWD VYCD
Vertical odd position of the active display area (VDO-in) Clamp pulse output timing (VDO-in) Clamp pulse width (VDO-in) Analog input YC delay (VDO-in)
0~3 0~255 0~7 0~63 0~255 0~15 0~255
0 95 3 0
0 70 3 0
YPbPr 480P
0 40 3 0
YPbPr 1080i
0 90 3 0 119 7 130 160 0
MID Mode: All (Single & P&P & Favorite)
8 9
VSTP VSTT
PD stop line count of external PLL (VDO-in) PD start line count of external PLL (VDO-in)
10
VHSC
Horizontal sync cycle (VDO-in)
Note: The same MID3 service data is used for DX1A-2001&2000.
-- 40 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#12): MID3 (VDO-in Data) (Part-2/2)
Data Initial Setting
(32V&36V CRTs) MID Mode: P&P / Favorite
YPbPr 480P YPbPr 1080i Dummy 480i YPbPr 480P YPbPr 1080i Dummy 480i
Data Initial Setting
(32V&36V CRTs) MID Mode: FREEZE
Register No & Name Comment
YC 480i
Dummy-480i settings are used for No Signal cases.
#0 VDHP (cont.) #1 VDHS (cont.) #2 VDVE (cont.) #3 VDVS (cont.)
197 219 24 56
127 154 53 112
91 151 37 126
179 199 24 56
131 153 53 112
98 149 37 126
179 199 24 56
Note: The same MID3 service data is used for DX1A-2001&2000.
DX1A-2001&2000 SERVICE LIST (#13): MID5 (Picture Data: MIDE) (Part-1/4)
Device Name: CXD9509AQ { MID-XA / Fujitsu & SONY } / IC3408 (B-board) / P/N: 8-759-672-57 (SBorSD#: NA) Slave Address: 2Eh { Controlled through MID-XA Micro (IC3090/B-board, Slave Address: 64h) / P/N: 6-800-050-01 (SB#: V4216) } MID-XA Micro (MASK type): MB94918RPF-G-137-BND, MID-XA Software: Version 12/08/00, (P/N: 6-800-050-01)
Data Initial/Average Setting
(32V&36V CRTs) UHF/VHF & CVideo
Pro Movie Standard Vivid Pro
Data Initial/Average Setting
(32V&36V CRTs) YPbPr-480i (DVD)
Movie Standard Vivid
Register No & Name Control Register Function & Link Register Name (Software) Data Type Data Range
Settings for P&P (Main)
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
POP MHLY MHLC MVLY MVLC MHYR MHYL MHYE MHYO MHCR MHCL MHCE MHCO MVYR MVYL MVYE MVCR MVCL MVCE
Selection of service data tables (Table #: 0~15) Y coefficient code of Horizontal LPF (M) m_hlpf_ycoef C coefficient code of Horizontal LPF (M) m_hlpf_ccoef Y coefficient code of Vertical LPF (M) m_vlpf_ycoef C coefficient code of Vertical LPF (M) m_vlpf_ccoef Y coreing code of horizontal enhancement (M) m_henh_ycore Y cliping code of horizontal enhancement (M) m_henh_yclip Y level code of horizontal enhancement (M) m_henh_yenh Y coefficient code of horizontal enhancement (M m_henh_ycof C coreing code of horizontal enhancement (M) m_henh_ccore C cliping code of horizontal enhancement (M) m_henh_cclip C level code of horizontal enhancement (M) m_henh_cenh C coefficient code of horizontal enhancement (M m_henh_ccof Y coreing code of vertical enhancement (M) m_venh_ycore Y cliping code of vertical enhancement (M) m_venh_yclip Y level code of vertical enhancement (M) m_venh_yenh C coreing code of vertical enhancement (M) m_venh_ccore C cliping code of vertical enhancement (M) m_venh_cclip C level code of vertical enhancement (M) m_venh_cenh
0~15 0~3 0~3 0~3 0~3 0~3 0~3 0~7 0, 1 0~3 0~3 0~7 0, 1 0~3 0~3 0~7 0~3 0~3 0~7
0 1 3 0 0 0 1 4 1 0 1 0 1 0 1 0 0 1 0
1 1 3 0 0 0 1 0 1 0 1 0 1 0 1 0 0 1 0
2 1 3 0 0 0 1 0 1 0 1 0 1 0 1 0 0 1 0
3 1 3 0 0 0 1 0 1 0 1 0 1 0 1 0 0 1 0
4 1 3 0 0 0 1 3 1 0 1 0 1 0 1 0 0 1 0
5 1 3 0 0 0 1 0 1 0 1 0 1 0 1 0 0 1 0
6 1 3 0 0 0 1 0 1 0 1 0 1 2 1 2 0 1 0
7 1 3 0 0 0 1 0 1 0 1 0 1 2 1 5 0 1 0
See the next page.
Note: The same MID5 service data is used for DX1A-2001&2000.
-- 41 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#13): MID5 (Picture Data: MIDE) (Part-2/4)
Data Initial/Average Setting
(32V&36V CRTs) YPbPr-480p
Movie Standard Vivid Pro Movie Standard Vivid
Data Initial/Average Setting
(32V&36V CRTs) YPbPr-1080i
Register No & Name
Comment
Pro
#0 POP (cont.) #1 MHLY (cont.) #2 MHLC (cont.) #3 MVLY (cont.) #4 MVLC (cont.) #5 MHYR (cont.) #6 MHYL (cont.) #7 MHYE (cont.) #8 MHYO (cont.) #9 MHCR (cont.) #10 MHCL (cont.) #11 MHCE (cont.) #12 MHCO (cont.) #13 MVYR (cont.) #14 MVYL (cont.) #15 MVYE (cont.) #16 MVCR (cont.) #17 MVCL (cont.) #18 MVCE (cont.)
8 1 3 0 0 0 1 4 1 0 1 0 1 0 1 0 0 1 0
9 1 3 0 0 0 1 0 1 0 1 0 1 0 1 0 0 1 0
10 1 3 0 0 0 1 0 1 0 1 0 1 2 1 2 0 1 0
11 1 3 0 0 0 1 0 1 0 1 0 1 2 1 5 0 1 0
12 1 3 0 0 0 1 4 1 0 1 0 1 0 1 0 0 1 0
13 1 3 0 0 0 1 0 1 0 1 0 1 0 1 0 0 1 0
14 1 3 0 0 0 1 0 1 0 1 0 1 0 1 0 0 1 0
15 1 3 0 0 0 1 0 1 0 1 0 1 0 1 0 0 1 0
Note: The same MID5 service data are used for DX1A-2001&2000.
-- 42 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#13): MID5 (Picture Data: MIDE) (Part-3/4)
Data Initial/Average Setting
(32V&36V CRTs) UHF/VHF & CV
Pro Movie Standard Vivid Pro
Data Initial/Average Setting
(32V&36V CRTs) YPbPr-480i (DVD)
Movie Standard Vivid
Register No.&Name Control Register Function & Link Register Name (Software) Data Type Data Range
Settings for P&P (Sub)
0 POP 19 SHLY 20 SHLC 21 SVLY 22 SVLC 23 SHYR 24 SHYL 25 SHYE 26 SHYO 27 SHCR 28 SHCL 29 SHCE 30 SHCO 31 SVYR 32 SVYL 33 SVYE 34 SVCR 35 SVCL 36 SVCE s_hlpf_ycoef s_hlpf_ccoef s_vlpf_ycoef s_vlpf_ccoef s_henh_ycore s_henh_yclip s_henh_yenh s_henh_ycof s_henh_ccore s_henh_cclip s_henh_cenh s_henh_ccof s_venh_ycore s_venh_yclip s_venh_yenh s_venh_ccore s_venh_cclip s_venh_cenh
Selection of service data tables (Table #: 0~15) Y coefficient code of Horizontal LPF (S) C coefficient code of Horizontal LPF (S) Y coefficient code of Vertical LPF (S) C coefficient code of Vertical LPF (S) Y coreing code of horizontal enhancement (S) Y cliping code of horizontal enhancement (S) Y level code of horizontal enhancement (S) Y coefficient code of horizontal enhancement (S C coreing code of horizontal enhancement (S) C cliping code of horizontal enhancement (S) C level code of horizontal enhancement (S) C coefficient code of horizontal enhancement (S Y coreing code of vertical enhancement (S) Y cliping code of vertical enhancement (S) Y level code of vertical enhancement (S) C coreing code of vertical enhancement (S) C cliping code of vertical enhancement (S) C level code of vertical enhancement (S)
0~15 0~7 0~7 0~7 0~7 0~3 0~3 0~7 0, 1 0~3 0~3 0~7 0, 1 0~3 0~3 0~7 0~3 0~3 0~7
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
3 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
4 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
5 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
6 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
7 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
See the next page.
Note: The same MID5 service data is used for DX1A-2001&2000.
-- 43 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#13): MID5 (Picture Data: MIDE) (Part-4/4)
Data Initial/Average Setting
(32V&36V CRTs) YPbPr-480p
Movie Standard Vivid Pro Movie Standard Vivid
Data Initial/Average Setting
(32V&36V CRTs) YPbPr-1080i
Register No.&Name Comment
Pro
#0 POP (cont.) #19 SHLY (cont.) #20 SHLC (cont.) #21 SVLY (cont.) #22 SVLC (cont.) #23 SHYR (cont.) #24 SHYL (cont.) #25 SHYE (cont.) #26 SHYO (cont.) #27 SHCR (cont.) #28 SHCL (cont.) #29 SHCE (cont.) #30 SHCO (cont.) #31 SVYR (cont.) #32 SVYL (cont.) #33 SVYE (cont.) #34 SVCR (cont.) #35 SVCL (cont.) #36 SVCE (cont.)
8 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
9 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
10 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
11 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
12 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
13 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
14 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Note: The same MID5 service data are used for DX1A-2001&2000.
DX1A-2001* SERVICE LIST (#14): On-Screen Display (OSD)
Device Name: M306V2ME-153FP (V1.0) { System Micro (MASK type) / Mitsubishi } / IC701 (A-board) Slave Address: 60h System Micro (MASK type): M306V2ME-153FP, Sys-Software: Version 1.0, P/N: 6-800-051-01 (SB#: V9091)
Data Initial/Average Setting
(32V&36V CRTs)
Register No & Name Data Type
Control Register Function & Link
Data Range
Comment 0~255 0~255 0~255 0~255 23 33 5 32
C: Common data
0 1 2 3
HPOS HPOF VPOS VPOT
OSD horizontal position Horizontal position for Favorite mode OSD vertical position Vertical position for P&P (Twin) mode
C C C C
Note: * This OSD settings are used for DX1A-2001 ONLY. (DX1A-2000 uses two OSD settings based on two versions of system micros.)
-- 44 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#15): SNNR
Related Control Devices: mPD64082 { 3D-Comb / NEC } / IC3501 (BC-board) / Slave Address: B8h CXA2103Q { Chroma Decoder / SONY } / IC3048 (B-board) / Slave Address: 9Ah (Main) CXA2150Q { CRT Driver / SONY } / IC201 (A-board) / Slave Address: 86h
Data Initial/Average Setting
32V&36V CRTs
Register No & Name Control Register Function & Link Data Type Data Range
Comment
0 C 0, 1 0
WSLT Data / Threthold Range
SNNR
0~3
0
C: Comon data
1
SNNR data setting Selection of SNNR data settings; SNFX 0: Set SNNR automatically according to WSLT value (read data) 0~255 0~30 31~62
2
WSLT
Noise level detection data thretholds for SNNR data (read data)
63~126 127~255
SNNR data used as the (-) offset settings
SNNR Settings Based on WSL Data ( - Offset Data)
3 4 0 1 0 0 0 0 0 0 0 0 0 -----0
CPFG CPFT
SNNR = 0/1/2/3 @ WSLT £ 0/31/63/127, respectively Related to 3D-COMB (mPD64082) / #19 YPFG settings Related to 3D-COMB (mPD64082) / #18 YPFT settings 1 1 0 1 1 1 1 0 0 0 0
0 0 0
1 1 0
2 2 0 1 1 0 2 2 3 2 0 0 0 0
3 3 0 1 1 0 3 3 4 3 0 0 0 0
SNNR data used as the direct settings
5 6 ----------------------------------------------
CCOR CHCG
Related to 3D-COMB (mPD64082) / #20 YHCO settings Related to 3D-COMB (mPD64082) / #21 YHCG settings
0~3 --------------------------
SNNR data used as the (-) offset settings
7 CAPG 8 3SHP 9 MIDD 10 5SHP 11 5YF1 12 5CDS 13 5LTI 14 5CTI 15 5VML
Related to 3D-COMB (mPD64082) / #16 VAPG settings Related to CXA2103 / #6 SHAP settings Related to CXA2150P-3 / #19 MIDE settings Related to CXA2150P-4 / #4 USHP settings Related to CXA2150P-3 / #10 F1LV settings Related to CXA2150P-3 / #11 CDSP settings Related to CXA2150P-3 / #12 LTLV settings Related to CXA2150P-3 / #14 CTLV settings Related to CXA2150P-3 / #1 UVML settings
SNNR data used as the (+) offset settings
SNNR Settings Based on WSL Data ( + Offset Data)
16
5VMC
Related to CXA2150P-3 / #3 VMCR settings
+1
+2
+3
Note: The same SNNR service data is used for DX1A-2001&2000. Please refer to the part numbers and SBorSD numbers given in the service list for these devices.
-- 45 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#16): ID-1 Detection (ID1)
Device Name: CXD2085M { ID-1 Decoder / SONY } / IC3603 (B-board) / P/N: 8-752-395-13 (SD#: S98511B) Slave Address: 40h
Data Initial/Average Setting
(32V&36V CRTs)
Register No & Name Control Register Function & Link Data Type Data Range
Comment
0 C 0, 1 0
XJGL
C
0, 1
0
C: Common data
1
LNJI
XJGLK: Setting for memorizing or not the ID-1 detection status LNJ1: Setting for the multi/single-line ID-1 detection
Note: The same ID1 service data are used for DX1A-2001&2000. Other servcie controls related to CXD2085 (IDSW & DATA) are lised in Service List (CXA2150P-4) for easier engineering adjustment.
DX1A-2001&2000 SERVICE LIST (#17): Closed Caption Display & Parental Control (CCD&VCHIP)
Device Name: CXP85840A-039Q { CCD&Vchip Micro (MASK type) / SONY } / IC3602 (Main) & IC3601 (Sub) (B-board) / P/N: 8-752-916-40 (SD#: S97739B) Slave Address: 68h (Main) & 6Ch (Sub) CCD&Vchip Micro Software: Version 2.14
Data Initial/Average Setting
(32V&36V CRTs)
Register No & Name Control Register Function & Link Data Type Data Range
Comment C: Common data
0 HPRM 1 HPRS 2 RND 3 CCDI 4 CRIP 5 CRIT 6 CHMK 7 FPOL 8 LANG 9 DATA 10 VCHIP
Horizontal position of CCD (Main) Horizontal position of CCD (Sub) OSD rounding control Interuption cointrol CRI count & parity count Charge/Discharge timing control for slice voltage level Horizontal mask width Field polarity selection
0: MASK-type micro, 1: OTP-type micro
Switch for CCD service/test data Selection of Vchip controls
C C C C C C C C C C C
0~255 0~255 0, 1 0~7 0~7 0, 1 0~63 0, 1 0~3 0, 1 0, 1
46 46 1 3 4 0 42 1 0 0 0
Note: The same CCD&VCHIP service data is used for DX1A-2001&2000.
-- 46 --
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
DX1A-2001&2000 SERVICE LIST (#18): OPTIONS (OP)
Device Name: M306V2ME-153FP (V1.0) { System Micro (MASK type) / Mitsubishi } / IC701 (A-board) Slave Address: 60h
System Micro (MASK type): M306V2ME-153FP, Sys-Software: Version 1.0, P/N: 6-800-051-01 (SB#: V9091)
Data Initial/Average Setting
(32V&36V CRTs)
Register No & Name Control Register Function & Link Data Type Data Range
Comment C: Common data
0 1 2 3
DLY1 DLY2 DLY3 RAMW
AC-RLY to MAIN-RLY timing = DLY1 x 50 ms Power-On Mute timing = DLY2 x 50 ms DGC-RLY to MAIN-RLY timing = DLY3 x 50 ms RAM monitor on/off
C C C C
0~15 0~31 0~15 0, 1
4 12 7 0
Note: The same OP service data is used for DX1A-2001&2000.
DX1A-2001* SERVICE LIST (#19): IDENTIFICATION (ID)
Device Name: M306V2ME-153FP (V1.0) { System Micro (MASK type) / Mitsubishi } / IC701 (A-board) Slave Address: 60h
System Micro (MASK type): M306V2ME-153FP, Sys-Software: Version 1.0, P/N: 6-800-051-01 (SB#: V9091)
Data Initial/Average Setting
(32V/36V/40V CRTs)
Register No & Name Control Register Function & Link Data Type Data Range
Comment
Shipping Destination-related Settings
KV-32HS20 KV-36HS20 KV-32HS20H
KV-32XBR450 KV-36XBR450 KV-36XBR450H
KV-32XBR450C KV-36XBR450C
0 1 2 3 4 5 6 7
ID0 ID1 ID2 ID3 ID4 ID5 ID6 ID7
Selection of OSD languages & color systems Selection of composite & s-video inputs Selection of audio-related controls Selection of basic system settings Selection of basic system settings Selection of advanced system settings Selection of sub picture-related settings Selection of some reserved settings
0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255
89 127 239 98 203 177 54 24
89 127 255 106 203 177 54 24
89 127 255 90 203 177 54 24
Note: * These ID settings are used for DX1A-2001 ONLY. (DX1A-2000 uses different ID settings.) The system micro name, software&patch versions, and the status of NVM devices are displayed only when in this service catergory (#19): ID.
-- 47 --
5-3. DIAGRAMS BLOCK DIAGRAM (1 OF 4)
ABL S V DRVV TIM
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
IC5513 Q8002 HV-STOP-3 15V
6 1 7
Q8001 BUFF IC5511
3 4 1
DY-CONV.CONT REF.V-OUT H_STAT H_DY-CONV SCL
2 1 7 1 6 1
V-SAW HD-IN SCL SDA
5 8 6 9
1 2
6 8
12V
3
IC8003 CONTROL
IC8004 BUFF
DQP-CONTROLLER
5
IC5515
3
V_STAT
AMP
CN5510
1 2 3
T8001 NX-6000 :RHT
1 2
9 1
H IN
SDA
CY+ NC CYTO DY
1 2
PH8001 HV FEEDBACK
V IN PWM DACO PARA1 DAC1
0 1 4
8
HV
Q5007 ABL-CONT Q5006 LATCH-1 IC5512 -12-REG
2
9
4
3
L8002
5 4 2 1
9
13 4 1 14
10
SWO
8 6 1 1
H-TILT PARA2
-15V
IC5510 NS-OUT
2 4 1 1
IC5514 VPIN-OUT
2 4
IC5506 DQP-AMP1
1
12V
10
4 2
6
8
3
N/S
4
15
Q8019 DF PROT
V PIN
Q8014 CONVERTER IC8002 HV DRIVE VG(H)
2 6 1 7 FV 5 16
V PIN
6
17
T8002 :DFT
Q8020 INVERT
CN5509
3 2 6 1
12
F/B VS
5 1
4
11
N/S COIL + N/S COIL NC 135V NC E QP+ NC QPNC V PIN+ V PINTO A BOARD CN203
1
V SENSE Q8013 CONVERTER OCP
9
Q5502 BUFF
Q5507 DQP-OUT 135V
11 10 9 8
VG(L)
2 1
12
1
Q8015 DF ON/OFF SW1
Q8016 DF ON/OFF SW2
Q5505 DQP-PROT
2 1
7 6 5
IC5504 DQP-AMP2
4
4 3 2
V PIN N/S CLK1/S CLK DAT1/S DAT
1
Q8018 IC8001 PROT-DETECT-1
9
Q5001 PWM-DRV-1
Q5004 HOCP
DF OUT Q5003 Q8023 DF-DRV-1 Q5002 PWM-DRV-2 Q8008 IK-PROT1 Q8022 DF-DRV-2
5 7
PWM-OUT
Q8009 +B-OCP
5
CN5503
1 1 1 2 3 4 5 6 7 8 9 10 M PIN ABL S V TIM V DRV+ V DRVN/S V PIN EW DRV 3 1
IC5002 PWM-CONT
6
ABL S V TIM V DRV+ V DRVCN201 TO A BOARD N/S V PIN EW DRV E DF PARA M PIN
1
Q5011 HSAW-SW
200V
15V Q5508 DF-DRV-1 Q8003 HV-STOP-2
1 0 1 8 6 4 7
2
Q5016 200V REG1
IC5001 ERROR AMP
12V
2
Q5015 200V REG2
Q8007 IK-PROT2
Q5509 DF-DRV-2 IC5502 DQP-DF-CONT
7 3 1 5 1 EW DRV 6 5
1
Q5014 200V REF
Q8004 HV-STOP-4
7 2
Q5017 200V.DET
Q5504
CN5501
2
DF-OFFSW
1 2 V FBP
1 1
V FBP
Q5501 DF PHASE
Q5503 AFC BUFF2
6 HP IN
HP IN CN706 TO A BOARD SCP E B INT CLK1/S CLK DAT1/S DAT
3 4 5 6 7 8
Q8010 VD PROT
12V
Q5008 PROT-OUT Q5013 H-CENT-2
CLK1/S CLK DAT1/S DAT
Q5506 H.SAW.RST
H CENT
T5001 :HOT
CN5506
E NC CN703 TO A BOARD NC NC SCP R B E B INT DAT1/S DAT CLK1/S CLK
EW DRV 1 2 3 4 5 6 7 8 9 10 11 H PROT 6 HP IN H CENT
Q5012 H-CENT-1
2
IC5005 H-CENT
5
12
1
4
1
11
2
Q5022 BUFFER2
3
10
3
Q5021 BUFFER1 Q5023
9 5
IC5007 H-PROT-CONT1
HSAW-SW
8
5
L5003
7
6
Q5018 H PROT
8 2 4 1 7 0 1 1 1 3 1 1
Q5030 H-OUT Q5037 COR BUFF Q5019 S-COR-DRIVE1
7 4
2 TO C BOARD CN9002
M PIN
CN5505
T5002 :HDT
CN5003
I
H CENT H DRV E CN203 TO A BOARD V COMP IN H COMP IN E V PROT H PROT R B
1 2 3 4 5 6 7 8 9 10
H CENT H DRV
IC5006 HEATER-OUT
0
4 3 200V 2 1
H1 E 200V G2
H.DY H.DY V.DY V.DY
3
Q5020 Q5033 BUFF S-COR-DRIVE2
5 2
CN5002
6 1
L5005 :HLC
V PROT H PROT
1 2 3 1 5 3 2 4 4 5 6
H/DY(+) H/DY(+) H.DY(-) H.DY(-) V.DY(-) V.DY(+)
TO DY
H DRV
Q5034 H DUTY Q5026 DRIVE-1 Q5035 BUFF
3
Q5028 DRIVE Q5031 S-COR-OUT
IC5004 V-OUT
V FBP
Q5036 BUFF Q5027
Q5005 BUFFER F.B.-PLS OUT-PUT
6 5
DRIVE-2
Vcc(OUT) V-DRVV-DRV+
7
V DRV-
1
V DRV+ V PROT
9-965-898-01BLK 1 OF 4
-- 49 --
BLOCK DIAGRAM (2 OF 4)
CN6501 D6516 AU RECT
1 2 3 4 5 6
T6501
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
9 10
200V
AC RECT+ NC TO A BOARD CN6005 AC RECTNC PRI 15V GND
CN6502
AU +24V
+ -
8
11
MAIN 12V
O
IC5003 12V-REG
I
+15V AU GRD
7
12
+135V
6
13
IC6501
1 2 1
RY6501
AC OUT TO A BOARD
CN6013
MAIN DRIVER
4
14
AC OUT
VSENSE OCP
9
15
3
16
Q6503 PROT
CN6503
VG(H) 16
Q6507 CONVERTER
2
17
Q6520
1 18
P-SW(-) SUB 7V SET ON
AUDIO-PROT
1 2 3 4 5 6 7 8
RY6502
11
VS
15
+B OCP
SUB 7V 7V AUDIO GND AUDIO GND AUDIO 24V AUDIO 24V Q6530 LATCH-2 Q6527 AC-RLY-DRV
2 3 1
VG(L) 12
PH6501
4
Q6506 CONVERTER +15V
D6514 15V RECT
+ -
Q6521 OCP LATCH
AUDIO GND TO A BOARD CN7003 AUDIO GND AUDIO 24V AUDIO 24V
8
VC1
F/B
2
Q6526 LATCH
PH6502 MAIN CONTROL
4 1
-15V
Q6524 OCP LATCH
CN6504
AC RLY MAIN RLY E AC OFF E TO A BOARD CN702 NORMAL E WP
CN6505
1 2 3 4 5 6 7 8
Q6532 LATCH-1
Q6529 LATCH
PH6503
1 4
3
2
STBY 5V Q6531 MAIN-SW
3 4
IC6503 CONTROL
2
3
Q6528 VC-SW-2
1
CN6506
Q6522 OVP SW
2
IC6505 +B OVP
1
STBY 5V E MAIN 12V MAIN 5V E TO A BOARD CN6006 MAIN 9V E 33V
8 7 6 5 4 3 2 1
STBY5V
5
IC5008 5V/9V-REG
33V
8 7 6 3 5 4 3 2 1
+B OCP +B OVP E NVM5V PROT1 E DAT0/B DAT CLK0/B CLK TO A BOARD CN703
2 4
1
5
2
IC5501 33V
7
8 6
NVM
YPBPR FOR HD OR DVD
YPBRR FOR HD OR DVD
VIDEO 6
J2401 6P S TERMINAL BLOCK
Y1
SW1
J2408 5P
VR VB VR VG VB VG R L R L
J2407 5P
VIDEO 5
4
J4501
5
3 2
FL4501
7 11 4 3 2 10 5 9 8 7 6 5 4
D2PB
D2PR
D1PR
D1PB
D2Y
D1Y
DR2
D2L
DR1
D1L
CN4503
3 1
4 2
3
C1
4 2
1
V2-V IN E V2-C IN E V2-Y IN V2-S1 IN V2-SSW IN E V2-L IN E V2-R IN TO B BOARD CN3204
1 (VIDEO I/O)
FL4502
7
V1
S11 V1
V
1
VIDEO 1
L1
VIDEO 4
J2402
L
4 3
5
3 2
L1
V R
FL4503
7
2 1
1
R1
R1
L4
L
(AUDIO/VIDEO I/O-2 I/O)
Y3
SW2
R4
R
T6001 :LFT
3 1
4 2
C3 V VO
3
4
POWER SUPPLY
L
F6001 T6.3A 250V
CN6007
2 1
VIDEO 3
V2
S13
AC AC
CN6013
2
1
AC-IN
V3
LO
DGC-RLY
L2
2 1
AC OUT AC OUT
CN6001
TO D BOARD
CN6502
R L3 RO
Q6001 DRIVER
R2
R3
J2409 2P VAR OR FIX OUT
J2406 3P
J2403 MONITOR OUT
3 2 1
DGC NC DGC
CN6002
DGC DGC
D2Y
D1Y
D2L
D1L
D1R
D1PR
D2PR
D2PB
D1PB
D2R
J2405 3P
LO
RO
VO
Q6002 STBY 15V PROT
L
3 2 1 7
DGC NC DGC
CN6003
DGC DGC
CONTROL S IN CONTROL S OUT
R
STBY 5V
L4 L3 R3 R4 R1 V1 Y1 C1 S21 S11 S23 Y3 C3 S13 V3 L1
STBY 7V
B10 A11 B11 A10 A12 B12 A13 B13 A14 A15 B14 B15 A16 B16 A17 B17 A20 A21 A18 B19 B20 B21 B18 A22 A19 B22 A23 B23 A24 B24 A25 B26 B25 A27 A29 B28 A26 B27 B29 A28 A30 B30 A31 B31 A32 B32 A1 B1 A2 B2 A3 B3 A4 B4 A5 B5 A6 B6 A7 B7 A8 B8 A9 B9
E
E
E
E
E
E
E
E
E
E
E
LG
RG
Y1
C1
Y3
C3
V3
VG
V1
V4
S23
S13
S21
S11
D2Y
D1Y
D1L1
D1L2
D1L3
D2L1
D2L2
D2L3
D2SW
D2PR
D2PB
D1SW
D1PR
D1PB
AFC
D2L
D1L
D1R
D2R
LO
RO
V/F-L
V/F-R
L4
V0
R4
DEC-SW
L3
R3
R1
L1
E
STBY 15V
E
E
CTRL-SIN
CTRL-SOUT
TO B BOARD CN3205
CN2401 64P :DIN
E
E
E
-- 50 --
I
IC6011 DRIVER
2 8 4 1
CHECK CHECK
FOR CHECK
O
9
3
2
1
9-965-898-01BLK 2 OF 4
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
BLOCK DIAGRAM (3 OF 4)
Y/C SEP
CN3201 CN3500
COMP V OUT
AUTO WIDE
15 14 13 12 11 10 9 8 7