Text preview for : HarmanKardon-AVR320 rec.pdf part of Harman/Kardon AVR320 receiver
Back to : HarmanKardon-AVR320 rec.p | Home
harman/kardon
AVR320
A/V DOLBY DIGITAL RECEIVER
PRELIMINARY SERVICE MANUAL
CONTENTS
ESD WARNING.....................................2 LEAKAGE TESTING...............................3 BASIC SPECIFICATIONS........................4 FRONT PANEL CONTROLS....................5 REAR PANEL CONNECTIONS................10 REMOTE CONTROL FUNCTIONS...........12 TROUBLESHOOTING GUIDE..................15 UNIT EXPLODED VIEW........................16 EXPLODED VIEW PARTS LIST.............17 BULLETIN H/K2002-03.........................19 BULLETIN H/K2002-07.........................20 BLOCK DIAGRAM................................21 ELECTRICAL PARTS LIST....................22 SCHEMATICS.....................................71
harman/kardon, Inc. 250 Crossways Park Dr. Woodbury, New York 11797 Rev1 11/2002
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field effect transistors and semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage caused by static electricity. 1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device, which should be removed for potential shock reasons prior to applying power to the unit under test. 2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge build-up or exposure of the assembly. 3. Use only a grounded-tip soldering iron to solder or unsolder ES devices. 4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static" can generate electrical charges sufficient to damage ES devices. 5. Do not use freon-propelled chemicals. These can generate electrical change sufficient to damage ES devices. 6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material.) 7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. CAUTION : Be sure no power is applied to the chassis or circuit, and observe all other safety precautions. 8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together or your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES devices.
Each precaution in this manual should be followed during servicing. Components identified with the IEC symbol in the parts list are special significance to safety. When replacing a component identified with
, use only the replacement parts designated, or parts with the same ratings or resistance, wattage, or voltage that are designated in the parts list in this manual. Leakage-current or resistance measurements must be made to determine that exposed parts are acceptably insulated from the supply circuit before retuming the product to the customer.
2
Before returning the unit to the user, perform the following safety checks :
1. Inspect all lead dress to make certain that leads are not pinched or that hardware is not lodged between the chassis and other metal parts in the unit. 2. Be sure that any protective devices such as nonmetallic control knobs, insulating fishpapers, cabinet backs, adjustment and compartment covers or shields, isolation resistor-capacity networks, mechanical insulators, etc. Which were removed for the servicing are properly re-installed. 3. Be sure that no shock hazard exists ; check for leakage current using Simpson Model 229 Leakage Tester, standard equipment item No. 21641, RCA Model WT540A or use alternate method as follows : Plug the power cord directly Into a 120 volt AC receptacle (do not use an Isolation Transformer for this test). Using two clip leads, connect a 1500 ohms, 10watt Resistor paralleled by a 0.15uF capacitor, in series with all exposed metal cabinet parts and a known earth ground, such as a water pipe or conduit. Use a VTVM or VOM with 1000 ohms per volt, or higher sensitivity to measure the AC voltage drop across the resistor. (See diagram) Move the resistor connection to each exposed metal part having a return path to the chassis (antenna, metal, cabinet, screw heads, knobs and control shafts, escutcheon, etc.) and measure the AC voltage drop across the resistor. (This test should be performed with the 0.35 volt RMS or more is excessive and indicates a potential shock hazard which must be corrected before returning the unit to the owner.
3
Technical Specifications
Audio Section Stereo Mode Continuous Average Power (FTC) 65 Watts per channel, 20Hz20kHz, @ < 0.07% THD, both channels driven into 8 ohms Five-Channel Surround Modes Power Per Individual Channel Front L&R channels: 55 Watts per channel @ < 0.07% THD, 20Hz20kHz into 8 ohms Center channel: 55 Watts @ < 0.07% THD, 20Hz20kHz into 8 ohms Surround channels: 55 Watts per channel @ < 0.07% THD, 20Hz20kHz into 8 ohms Input Sensitivity/Impedance Linear (High-Level) Signal-to-Noise Ratio (IHF-A) 200mV/47k ohms 95dB AM Tuner Section Frequency Range Signal-to-Noise Ratio Usable Sensitivity Distortion Selectivity Video Section Television Format Input Level/Impedance Output Level/Impedance Video Frequency Response (Composite and S) Video Frequency Response (Component) General Power Requirement Power Consumption Dimensions (Max) Width Height Depth Weight 17.3 inches (440mm) 6.5 inches (165mm) 17.1 inches (435mm) 3201720kHz 45dB Loop 500µV 1kHz, 50% Mod 0.8% ±10kHz, 30dB
NTSC 1Vp-p/75 ohms 1Vp-p/75 ohms 10Hz8MHz (3dB) 10Hz30MHz (3dB) AC 120V/60Hz 72W idle, 580W maximum (2 channels driven)
Surround System Adjacent Channel Separation Analog Decoding 40dB (Pro Logic II, etc.) Dolby Digital 55dB DTS 55dB Frequency Response @ 1W (+0dB, 3dB) High Instantaneous Current Capability (HCC) Transient Intermodulation Distortion (TIM) Slew Rate FM Tuner Section Frequency Range Usable Sensitivity Signal-to-Noise Ratio Distortion Stereo Separation Selectivity Image Rejection IF Rejection 10Hz 100kHz ±35 Amps Unmeasurable 40V/µsec
32 lb (14.5kg)
Depth measurement includes knobs, buttons and terminal connections. Height measurement includes feet and chassis. All features and specifications are subject to change without notice. Harman Kardon is a registered trademark, and Power for the Digital Revolution is a trademark, of Harman Kardon, Inc.
TM
is a trademark of Harman International Industries, Inc. (Patent No. 5,386,478).
87.5108MHz IHF 1.3 µV/13.2dBf Mono/Stereo 70/68dB Mono/Stereo 0.2/0.3% 40dB @ 1kHz ±400kHz, 70dB 80dB 90dB
*Manufactured under license from Dolby Laboratories. "Dolby," "Pro Logic," "Pro Logic II" and the Double-D symbol are trademarks of Dolby Laboratories. Confidential Unpublished Works. ©19921999 Dolby Laboratories, Inc. All rights reserved. DTS, DTS Surround, DTS-ES and DTS Neo:6 are trademarks of Digital Theater Systems, Inc. UltraStereo is a trademark of UltraStereo Corp. VMAx is a registered trademark of Harman International Industries, Inc., and is an implementation of Cooper Bauck Transaural Stereo under patent license. Logic 7 is a registered trademark of Lexicon, Inc. Crystal is a registered trademark of Cirrus Logic Corp.
4 TECHNICAL SPECIFICATIONS
Front Panel Controls
¯ ~ ^ i
Ù Û Ú Ò 1 2
3 4
5
7 6 8
9 )
! @
# $
%
& ( ^ * Ó
Ô
1 Main Power Switch 2 System Power Control 3 Power Indicator 4 Headphone Jack 5 Dolby Mode Selector 6 DTS Surround Mode Selector 7 Logic 7 Mode Selector /< Button 8 Tone Mode 9 Surround Mode Selector ) Tuning Selector ! Tuner Band Selector
@ Set Button # Preset Station Selector $ Stereo Mode Selector /> Button % Input Source Selector ^ FM Mode Selector & DTS Neo:6 Mode Selector * Digital Optical 3 Input ( Input/Output Status Indicator Ó Digital Coax 3 Jack Ô Video 4 Input Jacks Bass Control
Ò Balance Control Ú Treble Control Û Digital Select Button Ù Channel Select Button i Volume Control ^ Input Indicators ~ Main Information Display ¯ Remote Sensor Window Surround Mode Indicators
1 Main Power Switch: Press this button to apply power to the AVR 320. When the switch is pressed in, the unit is placed in a Standby mode, as indicated by the amber Power Indicator 3 surrounding the System Power Control 2. This button MUST be pressed in to operate the unit. To turn the unit off and prevent the use of the remote control, this switch should be pressed until it pops out from the front panel so that the word "OFF" may be read at the top of the switch. NOTE: This switch is normally left in the "ON" position. 2 System Power Control: When the Main Power Switch 1 is "ON," press this button to turn on the AVR 320; press it again to turn
the unit off. Note that the Power Indicator 3 surrounding the switch will turn green when the unit is on. 3 Power Indicator: This LED will be lit in amber when the unit is in the Standby mode to signal that the unit is ready to be turned on. When the unit is in operation, the indicator will turn green. 4 Headphone Jack: This jack may be used to listen to the AVR 320's output through a pair of headphones. Be certain that the headphones have a standard 1/4" stereo phone plug. Note that the main room speakers will automatically be turned off when the headphone jack is in use.
5 Dolby Mode Selector: Pressing this selector button cycles the AVR through the various Dolby surround modes. The first press of the button switches the surround mode to the last Dolby surround mode that was in use. Each subsequent press selects the next mode in the following order:
DOLBY DIGITAL DOLBY PRO LOGIC II MUSIC
DOLBY PRO LOGIC II DOLBY PRO LOGIC II EMULATION MOVIES DOLBY 3 STEREO
6 DTS Surround Mode Selector: Pressing this selector button cycles the AVR through the DTS surround modes. The first press of the button selects the last DTS surround mode that
5 FRONT PANEL CONTROLS
Front Panel Controls
was in use. Each subsequent press selects the next DTS mode in the following order:
DTS-ES 6.1 DISCRETE DTS-ES 6.1 MATRIX DTS 5.1
@ Set Button: When making choices during the setup and configuration process, press this button to enter the desired setting as shown in the Main Information Display ~ into the AVR 320's memory. # Preset Station Selector: Press this button to scroll up or down through the list or stations that have been entered into the preset memory. (See page 32 for more information on tuner programming.) $ Stereo Mode Selector /> Button: Pressing this selector button cycles through the stereo modes, and it is also used to turn off all surround processing and place the unit in a traditional two-channel Stereo mode. The first press selects 5-Channel Stereo, the next press selects 8-Channel Stereo, and the third press selects "SURROUND OFF," which is true Stereo. When an adjustment is being made using the Channel Select Ù or Digital Select Û buttons, this button may be pressed to scroll through the available options. % Input Source Selector: Press this button to change the input by scrolling up or down through the list of input sources. ^ FM Mode Selector: Press this button to select Auto or Manual tuning. When the button is pressed so that the AUTO Indicator X lights, the tuner will search for the next station with an acceptable signal when the Tuning Selector )ué is pressed. When the button is pressed so that the AUTO Indicator X is not lit, each press of the Tuning Selector )ué will increase the frequency. (See page 31 for more information on using the tuner.) & DTS Neo:6 Mode Selector: Pressing this selector button cycles the AVR through the various DTS Neo:6 modes, which extract a fivechannel surround field from two-channel program material. The first press selects the last DTS Neo:6 surround mode that was in use, and each subsequent press selects the next mode in the following order: DTS Neo:6 MUSIC DTS Neo:6 MOVIES DTS Neo:6 EMULATION
7 Logic 7 Mode Selector /< Button: This button has two functions: In normal use, press it to select one of the Logic 7 modes. When an adjustment is being made using the Channel Select Ù or Digital Select Û buttons, this button may be pressed to scroll through the available options. 8 Tone Mode: Pressing this button enables or disables the Bass and Treble tone controls. When the button is pressed so that the words TONE IN appear in the Main Information Display ~, the settings of the Bass and Treble Ú controls may be used to adjust the output signals. When the button is pressed so that the words TONE OUT appear in the Main Information Display ~, the output signal will be "flat, without any bass or treble alter" ation, no matter how the actual Bass and Treble Controls Ú are adjusted. 9 Surround Mode Selector: Press this button to change the surround mode by scrolling through the list of available modes. Note that depending on the type of input, some modes are not always available. (See page 26 for more information about surround modes.) ) Tuning Selector: Press the left side of the button to tune lower-frequency stations and the right side of the button to tune higher-frequency stations. When a station with a strong signal is reached, the TUNED Indicator W will be lit in the Main Information Display ~ . To tune manually, tap the button lightly and note that the tuner will step up one frequency increment per button press. When the button is held for a few seconds you will note that the unit will quickly search the frequency band. Release it once the fast tuning starts; the tuner will automatically scan for the next station with an acceptable signal and then stop. ! Tuner Band Selector: Pressing this button will automatically switch the AVR 320 to the Tuner mode. Pressing it again will switch between the AM and FM frequency bands. (See page 31 for more information on the tuner.)
( Input/Output Status Indicator: This LED indicator will normally light green to show that the front panel Digital Coax 3 Ó jack is operating as an input. When this jack is configured for use as an output, the indicator will turn red to show that the jack may be used for recording. (See page 20 for more information on configuring the front panel jacks as outputs, rather than inputs.) Ó Digital Coax 3 Jack: This jack is normally used for connection to the output of portable audio devices, video game consoles or other products that have a coax digital jack. It may also be configured as an output jack, to feed a digital signal to a CD-R, MiniDisc or other digital recording device. (See page 20 for information on configuring the Digital Coax 3 Jack as an output.) Ô Video 4 Input Jacks: These audio/video jacks may be used for temporary connection to video games or portable audio/video products such as camcorders and portable audio players. Bass Control: Turn this control to modify the low-frequency output of the left/right channels by as much as ±10dB. Set this control to a suitable position for your taste or room acoustics. Ò Balance Control: Turn this control to change the relative volume for the front left/right channels. NOTE: For proper operation of the surround modes, this control should be at the midpoint, or "12 o'clock", position. Ú Treble Control: Turn this control to modify the high-frequency output of the left/right channels by as much as ±10dB. Set this control to a suitable position for your taste or room acoustics. Û Digital Select Button: When playing a source that has a digital output, press this button to select between the Optical * 31 and Coaxial Ó 32 Digital inputs. (See page 29 for more information on digital audio.) Ù Channel Select Button: Press this button to begin the process of trimming the channel output levels using an external audio source. (For more information on output level trim adjustment, see page 32.) i Volume Control: Turn this knob clockwise to increase the volume, counterclockwise to decrease the volume. If the AVR 320 is muted, adjusting volume control will automatically release the unit from the silenced condition.
* Digital Optical 3 Input: Connect the optical digital output of an audio or video product to this jack. When the input is not in use, be certain to keep the plastic cap installed to avoid dust contamination that might degrade future performance.
6 FRONT PANEL CONTROLS
Front Panel Controls
^ Input Indicators: A green LED will light to the left of the input that is currently the input source for the AVR 320. ~ Main Information Display: This display delivers messages and status indications to help you operate the receiver. (See pages 8 & 9 for a complete explanation of the Information Display.) ¯ Remote Sensor Window: The sensor behind this window receives infrared signals from the remote control. Aim the remote at this area and do not block or cover it unless an external remote sensor is installed.
Surround Mode Indicators: A green LED
will light in front of the surround mode that is currently in use.
7 FRONT PANEL CONTROLS
Front Panel Information Display
Z Y X W V U TSR Q
A B
C
A Bitstream Indicators B Optical Source Indicators C Sample Rate Indicators D DTS Mode Indicator E Dolby Digital Indicator F Coaxial Source Indicators G Dolby Pro Logic II Indicator H Analog Input Indicator I Dolby 3 Stereo Indicator
D
E F
G H I J K
L MN O
P
J Logic 7 Mode Indicators K 5-Channel/7-Channel Stereo Indicators L Hall Mode Indicators M Theater Mode Indicator N VMAx Mode Indicators O Multiroom Indicator P OSD Indicator Q Speaker/Channel Input Indicators R Preset Number/Sleep Timer Digital soundtrack has been selected. H Analog Input Indicator: This indicator lights when an analog input source has been selected. I Dolby 3 Stereo Indicator: This indicator lights when the Dolby 3 Stereo mode has been selected. J Logic 7 Mode Indicators: These indicators light to indicate that one of the Logic 7 modes is in use. Along with the main Logic 7 indicator, either 5.1 or 7.1 will light to indicate the selected speaker configuration. One of the three letters to the far right of this segment will light to show which version of Logic 7 processing is in use: C for the Cinema mode, M for the Music mode and E for the Enhanced mode used with two-channel sources. The Enhanced mode is only available with the 5.1 speaker configuration. (See page 26 for a description of the Logic 7 modes.) K 5-Channel/7-Channel Stereo Indicators: These indicators light to show if the 5-Channel or 7-Channel Stereo mode has been selected. L Hall Mode Indicators: These indicators light when one of the Hall modes has been selected. M Theater Mode Indicator: This indicator lights to show that the Theater mode is in use.
S Preset Indicator T Sleep Indicator U Memory Indicator V Stereo Indicator W Tuned Indicator X Auto Indicator Y Main Information Display Z Mute Indicator
A Bitstream Indicators: When the input is a digital source, one of these indicators will light to display the specific type of data signal in use. B Optical Source Indicators: These indicators light to show when an Optical Digital Input has been selected. C Sample Rate Indicators: One of these indicators will light when 96kHz or 192kHz source material is in use. D DTS Mode Indicator: This indicator lights when a DTS-encoded source is playing. E Dolby Digital Indicator: This indicator lights when a Dolby Digital source is being played. F Coaxial Source Indicators: These indicators light to show when a Coaxial Digital Input has been selected. G Dolby Pro Logic II Indicator: This indicator lights when the Dolby Pro Logic II mode has been selected. NOTE: It is possible to see the Dolby Pro Logic II indicator lit simultaneously with the Dolby Digital indicator, even though the Dolby Digital surround mode has been selected. This is due to the specifications for Dolby Digital processing, which require that the Dolby Pro Logic II mode be applied when a 2-channel Dolby signal is detected. If you desire 5.1-channel audio, check the audio settings in the menus for your DVD disc to make sure that a 5.1-channel Dolby
N VMAx Mode Indicators: One of these indicators lights when the VMAx mode is in use. VMAx F appears when the Far Field VMAx mode is selected; VMAx N appears when the Near Field VMAx mode is selected. (See page 27 for a description of the VMAx modes.) O Multiroom Indicator: This indicator lights when the multiroom system is active. Note that it will remain lit when the multiroom system is in use even though the main room system is in the Standby mode and all other indicators are dark. (See page 36 for more information on the Multiroom system.) P OSD Indicator: When the OSD system is in use, this indicator lights to remind you that the other indicators in this display do not function when the On-Screen Display is being used. Q Speaker/Channel Input Indicators: These indicators are multipurpose, indicating either the speaker type selected for each channel or the incoming data-signal configuration. The left, center, right, right surround and left surround speaker indicators are composed of three boxes, while the subwoofer is a single box. The center box lights when a "Small" speaker is selected, and the two outer boxes light when "Large" speakers are selected. When none of the boxes are lit for the center, surround or subwoofer channels, no speaker has been selected for one of those positions. (See page 22 for more infor-
8 FRONT PANEL INFORMATION DISPLAY
Front Panel Information Display
mation on configuring speakers.) The letters inside each of the center boxes display the active input channels. For standard analog inputs, only the L and R will light, indicating a stereo input. When a digital source is playing, the indicators will light to display the channels being received at the digital input. When the letters flash, the digital input has been interrupted. (See pages 23 & 30 for more information on the Channel Indicators.) R Preset Number/Sleep Timer: When the tuner is in use, these numbers indicate the specific preset memory location in use. (See page 32 for more information on preset stations.) When the Sleep function is in use, these numbers show how many minutes remain before the unit goes into the Standby mode. S Preset Indicator: This indicator lights when the tuner is in use to show that the Preset Number/Sleep Timer R is showing the station's preset memory number. (See page 32 for more information on tuner presets.) T Sleep Indicator: This indicator lights when the Sleep function is in use. The numbers in the Preset Number/Sleep Timer R indicator will show the minutes remaining before the AVR 320 goes into the Standby mode. (See page 28 for more information on the Sleep function.) U Memory Indicator: This indicator flashes when entering presets and other information into the tuner's memory. V Stereo Indicator: This indicator lights when an FM station is being tuned in stereo. W Tuned Indicator: This indicator lights when a station is being received with sufficient signal strength to provide acceptable listening quality. X Auto Indicator: This indicator lights when the tuner's Auto mode is in use. Y Main Information Display: This display shows messages relating to the status, input source, surround mode, tuner, volume level or other aspects of the AVR 320's operation. Z Mute Indicator: This indicator lights to remind you that the AVR 320's output has been silenced by pressing the Mute Button ° 43 . Press the Mute button again to return to the previously selected output level.
9 FRONT PANEL INFORMATION DISPLAY
Rear Panel Connections
37 38 36 35 33 31 34 32
k
j hf d ig e
b c a
·
¡ TM £ °
¢
§· ¶
ª
, ¤ / <
> fi
fl
h Video 1 Video Inputs i Video 2 Video Outputs j Video 3 Video Inputs k Video 2 Video Inputs 31 Optical Digital Inputs 32 Coaxial Digital Inputs 33 Video 2 Audio Outputs 34 Video 2 Audio Inputs 35 Video 3 Audio Inputs 36 Video 1 Audio Inputs 37 Video 1 Audio Outputs 38 Preamp Outputs
¡ AM Antenna TM FM Antenna £ Tape Inputs ¢ Tape Outputs Subwoofer Output § DVD Audio Inputs ¶ CD Inputs · Multiroom Outputs ª 6-Channel Direct Inputs , 8-Channel Direct Inputs / Digital Audio Outputs ¤ Video Monitor Outputs < DVD Video Inputs ¡ AM Antenna: Connect the AM loop antenna supplied with the receiver to these terminals. If an external AM antenna is used, make connections to the AM and GND terminals in accordance with the instructions supplied with the antenna. TM FM Antenna: Connect the supplied indoor or an optional external FM antenna to this terminal. £ Tape Inputs: Connect these jacks to the PLAY/OUT jacks of an audio recorder. ¢ Tape Outputs: Connect these jacks to the RECORD/INPUT jacks of an audio recorder. Subwoofer Output: Connect this jack to the line-level input of a powered subwoofer. If an external subwoofer amplifier is used, connect this jack to the subwoofer amplifier input. § DVD Audio Inputs: Connect these jacks to the analog audio jacks on a DVD or other video source.
> Front Speaker Outputs fi Center Speaker Outputs fl Surround Speaker Outputs Switched AC Accessory Outlet ° Unswitched AC Accessory Outlet · AC Power Cord a Video 2 Component Video Inputs b Component Video Outputs c DVD Component Video Inputs d Remote IR Output e Remote IR Input f Multiroom IR Input g Video 1 Video Outputs ¶ CD Inputs: Connect these jacks to the output of a compact disc player or CD changer. · Multiroom Outputs: Connect these jacks to an optional audio power amplifier to listen to the source selected by the mulitroom system in a remote room. ª 6-Channel Direct Inputs: When an optional, external processor or playback device with 5.1 audio capability is in use, connect the player's output jacks here. NOTE: To assist in making the correct connections for multichannel input output and speaker connections, all connection jacks and terminals have been color coded in conformance with the latest CEA standards as follows: Front Left: White Front Right: Red Center: Green Surround Left: Blue
Surround Right: Gray Surround Back Left: Brown Surround Back Right: Tan Subwoofer: Purple Digital Audio: Orange Composite Video: Yellow Component Video "Y": Green Component Video "Pr": Red Component Video "Pb": Blue , 8-Channel Direct Inputs: When an option, external processor or playback device with 6.1 or 7. 1 audio capability is in use, connect the Surround Back Left and Surround Back Right channel outputs of the player to these input jacks. / Digital Audio Outputs: Connect these jacks to the matching digital input connector on a digital recorder such as a CD-R or MiniDisc recorder.
10 REAR PANEL CONNECTIONS
Rear Panel Connections
¤ Video Monitor Outputs: Connect this jack to the composite or S-Video input of a TV monitor or video projector to view the on-screen menus and the output of any standard video source selected by the receiver's video switcher. < DVD Video Inputs: Connect these jacks to the composite or S-Video output jacks on a DVD or other video source. > Front Speaker Outputs: Connect these outputs to the matching + or terminals on your left and right speakers. When making speaker connections always make certain to maintain correct polarity by connecting the red (+) terminals on the AVR 320 to the red (+) terminals on the speakers and the black () terminals on the AVR 320 to the black () terminals on the speakers. See page 16 for more information on speaker polarity. fi Center Speaker Outputs: Connect these outputs to the matching + and terminals on your center channel speaker. In conformance with the new CEA color code specification, the Green Terminal is the positive, or "+" terminal that should be connected to the red (+) terminal on speakers with the older color coding. Connect the black () terminal on the AVR to the black negative () terminal on your speaker. (See page 16 for more information on speaker polarity.) fl Surround Speaker Outputs: Connect these outputs to the matching + and terminals on your surround channel speakers. In conformance with the new CEA color code specification, the Blue terminal is the positive, or "+" terminal that should be connected to the red (+) terminal on the Surround Left speaker with older color coding, while the Gray terminal should be connected to the red (+) terminal on the Surround Right speaker with the older color coding. Connect the black () terminal on the AVR to the matching black negative () terminals for each surround speaker. (See page 17 for more information on speaker polarity.) Switched AC Accessory Outlet: This outlet may be used to power any device you wish to have turned on when the AVR 320 is turned on with the System Power Control Button 2. ° Unswitched AC Accessory Outlet: This outlet may be used to power any AC device. The power will remain on at this outlet regardless of whether the AVR 320 is on or off. NOTE: The total power consumption of all devices connected to the accessory outlets should not exceed 100 watts. · AC Power Cord: Connect the AC plug to an unswitched AC wall output. a Video 2 Component Video Inputs: Connect the Y/Pr/Pb component video outputs of an HDTV Set-top convertor, satellite receiver, or other video source device with component video outputs to these jacks. b Component Video Outputs: Connect these outputs to the component video inputs of a video projector or monitor. When a source connected to one of the two Component Video Inputs ac is selected the signal will be sent to these jacks. c DVD Component Video Inputs: Connect the Y/Pr/Pb component video outputs of a DVD player to these jacks. d Remote IR Output: This connection permits the IR sensor in the receiver to serve other remote controlled devices. Connect this jack to the "IR IN" jack on Harman Kardon (or other compatible) equipment. e Remote IR Input: If the AVR 320's frontpanel IR sensor is blocked due to cabinet doors or other obstructions, an external IR sensor may be used. Connect the output of the sensor to this jack. f Multiroom IR Input: Connect the output of an IR sensor in a remote room to this jack to operate the AVR 320's multiroom control system. g Video 1 Video Outputs: Connect these jacks to the RECORD/INPUT composite or S-Video jack on a VCR. h Video 1 Video Inputs: Connect these jacks to the PLAY/OUT composite or S-Video jacks on a VCR or other video source. i Video 2 Video Outputs: Connect these jacks to the RECORD/INPUT composite or S-Video jacks on a VCR. j Video 3 Video Inputs: Connect these jacks to the PLAY/OUT composite or S-Video jacks on a VCR or other video source. k Video 2 Video Inputs: Connect these jacks to the PLAY/OUT composite or S-Video jacks on a VCR or other video source.
31 Optical Digital Inputs: Connect the optical digital output from a DVD player, HDTV receiver, the S/P-DIF output of a compatible computer sound card playing MP3 files or streams, LD player or CD player to these jacks. The signal may be either a Dolby Digital signal, a DTS signal or a standard PCM digital source. 32 Coaxial Digital Inputs: Connect the coax digital output from a DVD player, HDTV receiver, the S/P-DIF output of a compatible computer sound card playing MP3 files or streams, LD player or CD player to these jacks. The signal may be either a Dolby Digital signal, DTS signal or a standard PCM digital source. Do not connect the RF digital output of an LD player to these jacks. 33 Video 2 Audio Outputs: Connect these jacks to the RECORD/INPUT audio jacks on a VCR or other video source. 34 Video 2 Audio Inputs: Connect these jacks to the PLAY/OUT audio jacks on a VCR or other video source. 35 Video 3 Audio Inputs: Connect these jacks to the PLAY/OUT audio jacks on a VCR or other video source. 36 Video 1 Audio Inputs: Connect these jacks to the PLAY/OUT audio jacks on a VCR or other video source. 37 Video 1 Audio Outputs: Connect these jacks to the RECORD/INPUT audio jacks on a VCR.
Preamp Outputs: These jacks may be connected to the inputs of an optional, external power amplifier.
38
11 REAR PANEL CONNECTIONS
Main Remote Control Functions
a Power Off Button b IR Transmitter Window c Program/SPL Indicator d Power On Button e Input Selectors f AVR Selector g AM/FM Tuner Select h 6-Channel/8-Channel Direct Input i Test Button j Sleep Button k Surround Mode Selector l Night Mode m Channel Select Button n / / ¤ Buttons o < Button p Set Button q Digital Select r Numeric Keys s Tuner Mode t Direct Button u Tuning Up/Down v OSD Button w Dolby Mode Select Button x DTS Digital Mode Selector y Logic 7 Mode Select Button z Skip Down Button ` Transport Controls 28 Skip Up Button 29 Stereo Mode Select Button 30 DTS Neo:6 Mode Select 31 Macro Buttons 32 Disc Skip Button 33 Preset Up/Down 34 Clear Button 35 Memory Button 36 Delay/Prev. Ch. 37 > Button 38 Speaker Select 39 Multiroom 40 Volume Up/Down 41 SPL Indicator Select 42 Learn Button 43 Mute 44 EzSet Sensor Microphone
c b a 44 d f g i h j 40 k l m o q 36 r n n p 38 37 39 43
e
42 41
t v x
s 34 u 32 w y z 28 30
35 33 31 29
NOTE: The function names shown here are each but` ton's feature when used with the AVR 320. Most buttons have additional functions when used with other devices. See pages 4243 for a list of these functions.
12 MAIN REMOTE CONTROL FUNCTIONS
Main Remote Control Functions
IMPORTANT NOTE: The AVR 320's remote may be programmed to control up to eight devices, including the AVR 320. Before using the remote, it is important to remember to press the Input Selector Button e that corresponds to the unit you wish to operate. In addition, the AVR 320's remote is shipped from the factory to operate the AVR 320 and most Harman Kardon CD or DVD players and cassette decks. The remote is also capable of operating a wide variety of other products using the control codes that are part of the remote. Before using the remote with other products, follow the instructions on pages 3741 to program the proper codes for the products in your system. It is also important to remember that many of the buttons on the remote take on different functions, depending on the product selected using the Device Control Selectors. The descriptions shown here primarily detail the functions of the remote when it is used to operate the AVR 320. (See page 39 for information about alternate functions for the remote's buttons.) a Power Off Button: Press this button to place the AVR 320 or a selected device in the Standby mode. Note that this will turn off the main room functions, but if the Multiroom system is activated, it will continue to function. b IR Transmitter Window: Point this window towards the AVR 320 when pressing buttons on the remote to make certain that infrared commands are properly received. c Program/SPL Indicator: This three-color indicator is used to guide you through the process of programming the remote or learning commands from a remote into the AVR 320's remote code memory and it is also used as a level indicator when using the remote's EzSet capabilities. (See page 24 for more information on setting output levels, and see page 37 for information on programming the remote.) d Power On Button: Press this button to turn on the power to a device selected by pressing one of the Input Selectors e. e Input Selectors: Pressing one of these buttons will perform three actions at the same time. First, if the AVR 320 is not turned on, this will power up the unit. Next, it will select the source shown on the button as the input to the AVR 320. Finally, it will change the remote control so that it controls the device selected. After pressing one of these buttons you must press the AVR Selector Button f again to operate the AVR 320's functions with the remote. f AVR Selector: Pressing this button will switch the remote so that it will operate the AVR 320's functions. If the AVR 320 is in the Standby mode, it will also turn the AVR 320 on. g AM/FM Tuner Select: Press this button to select the AVR 320's tuner as the listening choice. Pressing this button when the tuner is already in use will select between the AM and FM bands. h 6-Channel/8-Channel Direct Input: Press this button to select the device connected to the 6-Channel Direct Inputs ª or the 8Channel Direct Inputs ,. (See page 33 for more information.) i Test Button: Press this button to begin the sequence used to calibrate the AVR 320's output levels. (See page 24 for more information on calibrating the AVR 320.) j Sleep Button: Press this button to place the unit in the Sleep mode. After the time shown in the display, the AVR 320 will automatically go into the Standby mode. Each press of the button changes the time until turn-off in the following order:
90 min 40 min 80 min 30 min 70 min 20 min 60 min 10 min 50 min OFF
ton is pressed, use the //¤ Buttons n to select the channel being adjusted, then press the Set Button p, followed by the //¤ Buttons n again, to change the level setting. (See page 32 for more information.) n //¤ Buttons: These multipurpose buttons are used to change or scroll through items in the on-screen menus, make configuration settings such as digital inputs or delay timing, or to select surround modes. When changing a setting, first press the button for the function or setting to be changed (e.g., press the Surround Mode Selector k to select a soundfield mode or the Digital Select Button q to change a digital input) and then press one of these buttons to scroll through the list of options or to increase or decrease a setting. The sections in this manual describing the individual features and functions contain specific information on using these buttons for each application. o < Button: This button is used to change the menu selection or setting during some of the setup procedures for the AVR 320. p Set Button: This button is used to enter settings into the AVR 320's memory. It is also used in the setup procedures for delay time, speaker configuration and channel output level adjustment. q Digital Select: Press this button to assign one of the digital inputs 31 32 *Ó to a source. (See page 29 for more information on using digital inputs.) r Numeric Keys: These buttons serve as a ten-button numeric keypad to enter tuner preset positions. They are also used to select channel numbers when TV, Cable or SAT has been selected on the remote, or to select track numbers on a CD, DVD or LD player, depending on how the remote has been programmed. s Tuner Mode: Press this button when the tuner is in use to select between automatic tuning and manual tuning. When the button is pressed so that the AUTO Indicator X goes out, pressing the Tuning Buttons u) will move the frequency up or down in singlestep increments. When the FM band is in use, pressing this button when a station's signal is weak will change to monaural reception. (See page 31 for more information.) t Direct Button: Press this button when the tuner is in use to start the sequence for direct entry of a station's frequency. After pressing the button, simply press the proper Numeric Keys r to select a station. (See page 32 for more information on the tuner.)
Note that this button is also used to change channels on your TV when the TV is selected. When the AVR 320 remote is being programmed with the codes to operate another device, this button is also used in the "Auto Search" process. (See page 37 for more information on programming the remote.) k Surround Mode Selector: Press this button to begin the process of changing the surround mode. After the button has been pressed, use the //¤ Buttons n to select the desired surround mode. (See page 28 for more information.) Note that this button is also used to tune channels when the TV is selected using the device Input Selector e. When the AVR 320 remote is being programmed with the codes of another device, this button is also used in the "Auto Search" process. (See page 37 for more information on programming the remote.) l Night Mode: Press this button to activate the Night mode. This mode is available in specially encoded digital sources, and it preserves dialog (center channel) intelligibility at low volume levels. m Channel Select Button: This button is used to start the process of setting the AVR 320's output levels to an external source. Once this but-
13 MAIN REMOTE CONTROL FUNCTIONS
Main Remote Control Functions
u Tuning Up/Down: When the tuner is in use, these buttons will tune up or down through the selected frequency band. If the Tuner Mode Button s^ has been pressed so that the AUTO Indicator X is illuminated, pressing and holding either of the buttons for three seconds will cause the tuner to seek the next station with acceptable signal strength for quality reception. When the AUTO Indicator X is NOT illuminated, pressing these buttons will tune stations in single-step increments. (See page 31 for more information.) v OSD Button: Press this button to activate the On-Screen Display (OSD) system used to set up or adjust the AVR 320's parameters. w Dolby Mode Selector: This button is used to select from among the available Dolby Surround processing modes. Each press of this button will select one of the Dolby Pro Logic II modes or Dolby 3 Stereo. When a Dolby Digital encoded source is in use, the Dolby Digital mode may also be selected. (See page 26 for the available Dolby surround mode options.) x DTS Digital Mode Selector: When a DTS-encoded digital source is selected, each press of this button will scroll thorugh the available DTS modes. The specific choice of modes will vary according to whether or not the source material contains DTS-ES 6.1 Discrete encoding. When a DTS source is not in use, this button has no function. (See page 40 for the available DTS Digital options.) y Logic 7 Selector: Press this button to select from among the available Logic 7 surround modes. (See page 26 for the available Logic 7 options.) z Skip Down Button: This button does not have a direct function on the AVR 320, but when used with a compatibly programmed CD or DVD changer it will change to the previous disc in the changer or carousel. ` Transport Controls: These buttons do not have any functions for the AVR 320, but they may be programmed for the forward/ reverse play operation of a wide variety of CD or DVD players, and audio or video cassette recorders. (See page 40 for more information.)
28 Skip Up Button: This button does not have a direct function on the AVR 320, but when used with a compatibly programmed CD or DVD changer it will change to the previous disc in the changer or carousel. 29 Stereo Mode Select Button: Pressing this button cycles through the stereo modes, and it is also used to turn off all surround
processing and place the unit in a traditional two-channel Stereo mode. The first press selects 5-Channel Stereo, the next press selects 8-Channel Stereo, and the third press selects "SURROUND OFF," which is true Stereo.
30 Macro Buttons: Press these buttons to store or recall a "Macro", which is a preprogrammed sequence of commands stored in the remote. (See page 38 for more information on storing and recalling macros.) 31 DTS Neo:6 Mode Select: Pressing this button cycles the AVR through the various DTS Neo:6 modes, which extract a five-channel surround field from two-channel program material. The first press selects the last DTS Neo:6 surround mode that was in use, and each subsequent press selects one of the other DTS Neo:6 modes. 32 Disc Skip Button: This button has no direct function for the AVR 320 but is most often used to change to the next disc in a CD or DVD player when the remote is programmed for that type of device. (See page 37 for more information on using the remote with products other than the AVR 320.) 33 Preset Up/Down: When the tuner is in use, press these buttons to scroll through the stations programmed into the AVR 320's memory. When some source devices, such as CD players, VCRs and cassette decks, are selected using the device Input Selectors e, these buttons may function as Chapter Step or Track Advance. 34 Clear Button: Press this button to clear
38 Speaker Select: Press this button to begin the process of configuring the AVR 320's bass management system for use with the type of speakers used in your system. Once the button has been pressed, use the //¤ Buttons n to select the channel you wish to set up. Press the Set Button p and then select another channel to configure. When all adjustments have been completed, press the Set Button p twice to exit the settings and return to normal operation. (See page 22 for more information.) 39 Multiroom: Press this button to activate the multiroom system or to begin the process of changing the input or volume level for the second zone. (See page 36 for more information on the Multiroom system.) 40 Volume Up/Down: Press these buttons to raise or lower the system volume. 41 SPL Indicator Select: This button activates the AVR 320's EzSet function to quickly and accurately calibrate the AVR 320's output levels. Press and hold the button for three seconds and then release it. Note that the test tone will begin circulating, and the Program/SPL Indicator c will change colors. During this sequence, EzSet will automatically adjust the output levels for all channels until they are equal, as shown by the Program/SPL Indicator c lighting green for each channel. Press this button again when the adjustment is complete to turn off the test tone. (See page 24 for more information on EzSet.) 42 Learn Button: Press this button to begin the process of "learning" the codes from another product's remote into the AVR 320's remote. (See page 37 for more information on using the remote's learning function.) 43 Mute: Press this button to momentarily silence the AVR 320 or TV set being controlled, depending on which device has been selected. When the AVR 320 remote is being programmed to operate another device, this button is pressed with the Input Selector Button e to begin the programming process. (See page 37 for more information on programming the remote.) 44 EzSet Sensor Microphone: The sensor microphone for the EzSet microphone is behind these slots. When using the remote to calibrate speaker output levels using EzSet, be sure that you do not hold the remote in a way that covers these slots. (See page 24 for more information on using EzSet.)
incorrect entries when using the remote to directly enter a radio station's frequency.
35 Memory Button: Press this button to enter a radio station into the AVR 320's preset memory. Once the MEMORY Indicator U flashes, you have five seconds to enter a preset memory location using the Numeric Keys r. (See page 31 for more information.) 36 Delay/Prev Ch.: Press this button to begin the process for setting the delay times used by the AVR 320 when processing surround sound. After pressing this button, the delay times are entered by pressing the Set Button p and then using the //¤ Buttons n to change the setting. Press the Set Button p again to complete the process. (See page 23 for more information.) 37 > Button: Press this button to change a setting or selection when configuring many of the AVR 320's settings.
14 MAIN REMOTE CONTROL FUNCTIONS
Troubleshooting Guide
SYMPTOM Unit does not function when Main Power Switch is pushed Display lights, but no sound or picture
CAUSE · No AC Power
SOLUTION · Make certain AC power cord is plugged into a live outlet · Check to see whether outlet is switch-controlled · Make certain that all input and speaker connections are secure · Press Mute button · Turn up volume control · Follow the instructions in the Display Brightness section on page 35 so that the display is set to VFD FULL · Check speaker wire connections for shorts at receiver and speaker ends · Contact your local Harman Kardon service depot · Select a mode other than Stereo · There is no surround information from mono sources · Check speaker mode configuration · The surround decoder may not create center- or rear-channel information from nonencoded programs · Change remote batteries · Press the AVR selector · Make certain front panel sensor is visible to remote or connect remote sensor · Move unit or antenna away from computers, fluorescent lights, motors or other electrical appliances · Resume play for DVD · Check that Digital Input is selected
· Intermittent input connections · Mute is on · Volume control is down · Display brightness is turned off · Amplifier is in protection mode due to possible short · Amplifier is in protection mode due to internal problems · Incorrect surround mode · Input is monaural · Incorrect configuration · Stereo or Mono program material · Weak batteries in remote · Wrong device selected · Remote sensor is obscured · Local interference · Digital audio feed paused
Unit turns on, but front panel display does not light up No sound from any speaker; light around power switch is red
No sound from surround or center speakers
Unit does not respond to remote commands
Intermittent buzzing in tuner Letters flash in the channel indicator display and digital audio stops
Processor Reset
In the rare case where the unit's operation or the displays seem abnormal, the cause may involve the erratic operation of the system's memory or microprocessor. To correct this problem, first unplug the unit from the AC wall outlet and wait at least three minutes. After the pause, reconnect the AC power cord and check the unit's operation. If the system still malfunctions, a system reset may clear the problem. To clear the AVR 320's entire system memory including tuner presets, output level settings,
delay times and speaker configuration data, first put the unit in Standby by pressing the System Power Control Button 2. Next, press and hold the Tone Mode 8 and the FM Mode Selector ^ buttons for three seconds. The unit will turn on automatically and display the RESET message in the Main Information Display Y. Note that once you have cleared the memory in this manner, it is necessary to reestablish all system configuration settings and tuner presets. NOTE: Resetting the processor will erase any configuration settings you have made for
speakers, output levels, surround modes, digital input assignments as well as the tuner presets. After a reset the unit will be returned to the factory presets, and all settings for these items must be reentered. If the system is still operating incorrectly, there may have been an electronic discharge or severe AC line interference that has corrupted the memory or microprocessor. If these steps do not solve the problem, consult an authorized Harman Kardon service center.
15 TROUBLESHOOTING GUIDE
44
45 78
46 37 47 48 49 50 51 38 40 41 1 36 35 34 33 32 31 77 30 29 42 43 57 59 58 61 62 63 64 65 66 19 67 52 42 55 56 54
52
2 4 3
8 10 9
7
6
5
68
69 70 71
28
11
27
26
67
76
72 73 75
16 14 12 13 15
17
18
19
20
21
22
23
24
25
74
23
24
MODEL S C ALE NONE S C ALE UNIT m / m
A VR 3 2 0
TOLER ANC E LES S ; ± LES S ; ± LES S ; ± LES S ; ±
P AR TS NAME P AR TS N O. DWG. N O.
E XP LOD E D VIE W
16
17
18
harman/kardon
Service bulletin # H/K2002-03 April 2002 To: All harman/kardon Service Centers Model: AVR320 Subject: Transformer Hum or Buzz
Service Bulletin
Warranty labor rate: MINOR repair
In the event you receive an AVR320 with the complaint "There is a hum or buzz sound coming from the unit", first confirm the sound is coming from the receiver itself and not at the loudspeaker output, then replace the Power Transformer:
1) Remove the top cover (14 Phillips screws) 2) Locate the Power Transformer; it is attached with (4) Phillips screws. 3) All connectors terminating the cable harness consisting of multiple conductors need to be unplugged from two main locations. Remove all plastic ties necessary to remove the harness. Most connectors have "tabs" on one side that should be depressed before the connector can be unplugged.
4) Remove and replace the Power Transformer with h/k part# 55199320XX. 5) Replace the harness, add new cable ties, plug in all connectors, (replace Component Video PCB if it was removed): replace the top cover. 6) Test the unit and confirm the hum or buzz is no longer present.
Model AVR320
Serial Number (120v) TH0044-01000 to TH0044-03854 TH0044-03855 To TH0044-08419 TH0044-08420 and above
Status
Action None Required
AVR320 AVR320
Hum or Buzz from Power Transformer
Replace Power Transformer None Required
19
harman/kardon, Incorporated 250 Crossways Park Dr. Woodbury, New York 11797
harman/kardon
Service bulletin # H/K2002-07 October 2002 To: All harman/kardon Service Centers Model: AVR320 Subject: Intermittent Output
Service Bulletin
Warranty labor rate: MINOR repair
In the event you receive an AVR320 receiver with the complaint "There is intermittent output from the receiver", follow the instructions below: All sources, all modes may be affected, using any audio connections; unit may also not turn off with the system power control. 1) Turn the unit on it's side so the bottom panel faces you, and the access cover (grille) is at the top. Remove the (9) Phillips screws holding the access cover on; one "foot" will come off with the cover. 2) Locate and inspect all soldered connections on the Main PCB, particularly in the area of connector CN411 and CN410, the 15 pin horizontal foil patterns (see illustration). 3) Repair as needed with solder or buss wire. 4) Test the unit, replace the access cover (grille).
MODEL AVR320
SERIAL NUMBER 120V All serial numbers affected
STATUS Connections may need repair or re-soldering
ACTION Check for broken connections and sufficient solder on Main PCB
20
harman/kardon, Incorporated 250 Crossways Park Dr. Woodbury, New York 11797
AVR 520Block.sch 1
Thu Mar 21 17:29:13 2002
21
AVR320 Electrical Parts List
Main PCB
Ref. Designator Capacitors
C101 C102 2034206039 or 157D-476M-5-IU 2034206039 or 157D-476M-5-IU 15002130 or 1500213041 J3471610031X J3470110031X 15002130 J3513101270X J3513101270X J3513101270X J3513101270X 20293470 J3513101270X J3513101270X J3513101270X J3513101270X 20250040 20250040 20293470 J3513101270X J3513101270X J3513101270X J3513101270X 20293470 20293470 J3513101270X J3513101270X 20293470 J3513101270X J3513101270X J3513101270X 20293470 1305550030 1305550030 11055300 11055300 20269070 20269070 20269080 20269080 30936070 30936070 60439150 60439150 1305550030 1305550030 1305550030 1305550030 55179360 55179360 55179360 55179360 11055540 1 PC CE 47U0F +20% 16.0V 85C 1 PC CE 47U0F +20% 16.0V 85C
Part Number
Qty
Description
C103 C104 C105 C106 C107 C108 C109 C110 C111 C112 C113 C115 C117 C118 C119 C120 C121 C122 C123 C124 C125 C126 C127 C128 C129 C130 C131 C401 C402 C403 C404 C405 C406 C407 C408 C409 C410 C411 C412 C413 C414 C415 C416 C417 C418 C419 C420 C425
1 PC CE 10U0F +20% 16.0V 85C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC CE 10U0F +20% 16.0V 85C CC 100P0F +10% -10% 50.0V Y5P CC 100P0F +10% -10% 50.0V Y5P CC 100P0F +10% -10% 50.0V Y5P CC 100P0F +10% -10% 50.0V Y5P CC 100N0F +80% -20% 50.0V F CC 100P0F +10% -10% 50.0V Y5P CC 100P0F +10% -10% 50.0V Y5P CC 100P0F +10% -10% 50.0V Y5P CC 100P0F +10% -10% 50.0V Y5P CC 220P0F +10% -10% 50.0V Y5P CC 220P0F +10% -10% 50.0V Y5P CC 100N0F +80% -20% 50.0V F CC 100P0F +10% -10% 50.0V Y5P CC 100P0F +10% -10% 50.0V Y5P CC 100P0F +10% -10% 50.0V Y5P CC 100P0F +10% -10% 50.0V Y5P CC 100N0F +80% -20% 50.0V F CC 100N0F +80% -20% 50.0V F CC 100P0F +10% -10% 50.0V Y5P CC 100P0F +10% -10% 50.0V Y5P CC 100N0F +80% -20% 50.0V F CC 100P0F +10% -10% 50.0V Y5P CC 100P0F +10% -10% 50.0V Y5P CC 100P0F +10% -10% 50.0V Y5P CC 100N0F +80% -20% 50.0V F CE 10U0F +20% 50.0V 85C CE 10U0F +20% 50.0V 85C CC 68P0F +5% -5% 50.0V NP0 CC 68P0F +5% -5% 50.0V NP0 CE 100U0F +20% 25.0V 85C CE 100U0F +20% 25.0V 85C CE 220U0F +20% 10.0V 85C CE 220U0F +20% 10.0V 85C CC 12P0F +5% -5% 50.0V NP0 CC 12P0F +5% -5% 50.0V NP0 CC 33P0F +5% -5% 50.0V NP0 CC 33P0F +5% -5% 50.0V NP0 CE 10U0F +20% 50.0V 85C CE 10U0F +20% 50.0V 85C CE 10U0F +20% 50.0V 85C CE 10U0F +20% 50.0V 85C CPM 100N0F +10% 63.0V CPM 100N0F +10% 63.0V CPM 100N0F +10% 63.0V CPM 100N0F +10% 63.0V CC 2N2F +10% -10% 50.0V Y5P
22
Ref. Designator
C426 C431 C432 C433 C483 C484 C489 C490 C492 C494 C496 C497 C498 C501 C502 C503 C504 C505 C506 C507 C508 C509 C510 C513 C551 C552 C553 C554 C555 C556 C564 C565 C566 C567 C568
Part Number
11055540 10364820 10364820 10364820 55095430 10364820 1305550030 1305550030 1305550030 1305550030 1305550030 1305550030 1305550030 1305550030 11055300 20269070 20269080 30936070 60439150 1305550030 1305550030 55179360 55179360 11055540 55179400 55179400 55179400 20252670 1105934091 1105934091 55095430 55095430 10364820 10364820 15002130 or 1500213041 J3471610031X J3470110031X 5512607016 8043682091 5512607016 8043682091 5512607016 8043682091 13076940 13076940 13076940 13076940 55134050 55329160 55134050 55329160 40433130NR 40433130NR 55126160DD 13039870 13076940 13076940
Qty
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC
Description
CC 2N2F +10% -10% 50.0V Y5P CPF 47N0F +10% 100.0V CPF 47N0F +10% 100.0V CPF 47N0F +10% 100.0V CPM 100N0F +10% 250.0V CPF 47N0F +10% 100.0V CE 10U0F +20% 50.0V 85C CE 10U0F +20% 50.0V 85C CE 10U0F +20% 50.0V 85C CE 10U0F +20% 50.0V 85C CE 10U0F +20% 50.0V 85C CE 10U0F +20% 50.0V 85C CE 10U0F +20% 50.0V 85C CE 10U0F +20% 50.0V 85C CC 68P0F +5% -5% 50.0V NP0 CE 100U0F +20% 25.0V 85C CE 220U0F +20% 10.0V 85C CC 12P0F +5% -5% 50.0V NP0 CC 33P0F +5% -5% 50.0V NP0 CE 10U0F +20% 50.0V 85C ALSO 1305550030 CE 10U0F +20% 50.0V 85C CPM 100N0F +10% 63.0V CPM 100N0F +10% 63.0V CC 2N2F +10% -10% 50.0V Y5P CPM 68N0F +5% 63.0V CPM 68N0F +5% 63.0V CPM 68N0F +5% 63.0V CE 470U0F +20% 10.0V 85C CC 10N0F +10% -10% 50.0V Y5P CC 10N0F +10% -10% 50.0V Y5P CPM 100N0F +10% 250.0V CPM 100N0F +10% 250.0V CPF 47N0F +10% 100.0V CPF 47N0F +10% 100.0V
1 PC CE 10U0F +20% 16.0V 85C or or or
C569 C570 C571 C421 C422 C423 C424 C481 C481 C482 C482 C485 C486 C487 C488 C511 C512
1 PC CC 680P0F +10% -10% 50.0V Y5P 1 PC CC 680P0F +10% -10% 50.0V Y5P 1 PC CC 680P0F +10% -10% 50.0V Y5P 1 1 1 1 1 1 1 1 1 1 1 1 1 1 PC PC PC PC PC PC PC PC PC PC PC PC PC PC CE 470U0F +20% 63.0V 85C CE 470U0F +20% 63.0V 85C CE 470U0F +20% 63.0V 85C CE 470U0F +20% 63.0V 85C CE 8MI2F +20% 63.0V 85C CE 8MI2F +20% 63.0V 85C CE 8MI2F +20% 63.0V 85C CE 8MI2F +20% 63.0V 85C CE 2MI2F +20% 35.0V 85C CE 2MI2F +20% 35.0V 85C CE 6MI8F +20% 16.0V 85C CE 2MI2F +20% 16.0V 85C CE 470U0F +20% 63.0V 85C CE 470U0F +20% 63.0V 85C
23
Ref. Designator
Semiconductors D401 D402 D403 D404 D405 D406 D501 D502 D551 D552 D553 D554 D555 D556 D566 D567 Q401 Q402 Q403 Q404 Q405 Q406 Q407 Q408 Q411 Q412 Q413 Q414 Q415 Q416 Q417 Q418 Q419 Q420 Q421 Q422 Q423 Q424 Q427 Q428 Q429 Q430 Q431 Q432 Q501 Q502 Q503 Q504 Q506 Q507 Q508 Q509 Q510 Q511 Q512 Q514 Q515 Q516
Part Number
Qty
Description
13-0482 13-0482 13-0482 13-0482 13-0482 13-0482 13-0482 13-0482 13-0482 13-0482 13-0482 13-0482 13-0482 13-0482 13-0482 13-0482 20556600 20556600 20556600 20556600 20556600 20556600 TR031984100 TR031984100 20647850 20647850 20647850 20647850 20556600 20556600 55133260 55133260 55133240 55133240 55133260 55133260 55133240 55133240 20556600 20556600 55133240 55133240 55133260 55133260 20556600 20556600 20556600 TR031984100 20647850 20647850 20556600 55133260 55133240 55133260 55133240 20556600 55133240 55133260
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC
D-SLP 1N4148 100.0V 150E-3A D-SLP 1N4148 100.0V 150E-3A D-SLP 1N4148 100.0V 150E-3A D-SLP 1N4148 100.0V 150E-3A D-SLP 1N4148 100.0V 150E-3A D-SLP 1N4148 100.0V 150E-3A D-SLP 1N4148 100.0V 150E-3A D-SLP 1N4148 100.0V 150E-3A D-SLP 1N4148 100.0V 150E-3A D-SLP 1N4148 100.0V 150E-3A D-SLP 1N4148 100.0V 150E-3A D-SLP 1N4148 100.0V 150E-3A D-SLP 1N4148 100.0V 150E-3A D-SLP 1N4148 100.0V 150E-3A D-SLP 1N4148 100.0V 150E-3A D-SLP 1N4148 100.0V 150E-3A TR-SHPLF KTC3200BL N 100MI0A 120V TR-SHPLF KTC3200BL N 100MI0A 120V TR-SHPLF KTC3200BL N 100MI0A 120V TR-SHPLF KTC3200BL N 100MI0A 120V TR-SHPLF KTC3200BL N 100MI0A 120V TR-SHPLF KTC3200BL N 100MI0A 120V TR-SLPLF KTC3198BL N 150MI0A TR-SLPLF KTC3198BL N 150MI0A TR-SHPLF KTA1268BL P 100MI0A 120V TR-SHPLF KTA1268BL P 100MI0A 120V TR-SHPLF KTA1268BL P 100MI0A 120V TR-SHPLF KTA1268BL P 100MI0A 120V TR-SHPLF KTC3200BL N 100MI0A 120V TR-SHPLF KTC3200BL N 100MI0A 120V TR-SLPLF KTA1024 Y P 50MI0A -150V TR-SLPLF KTA1024 Y P 50MI0A -150V TR-SLPLF KTC3206 Y N 50MI0A 150V TR-SLPLF KTC3206 Y N 50MI0A 150V TR-SLPLF KTA1024 Y P 50MI0A -150V TR-SLPLF KTA1024 Y P 50MI0A -150V TR-SLPLF KTC3206 Y N 50MI0A 150V TR-SLPLF KTC3206 Y N 50MI0A 150V TR-SHPLF KTC3200BL N 100MI0A 120V TR-SHPLF KTC3200BL N 100MI0A 120V TR-SLPLF KTC3206 Y N 50MI0A 150V TR-SLPLF KTC3206 Y N 50MI0A 150V TR-SLPLF KTA1024 Y P 50MI0A -150V TR-SLPLF KTA1024 Y P 50MI0A -150V TR-SHPLF KTC3200BL N 100MI0A 120V TR-SHPLF KTC3200BL N 100MI0A 120V TR-SHPLF KTC3200BL N 100MI0A 120V TR-SLPLF KTC3198BL N 150MI0A TR-SHPLF KTA1268BL P 100MI0A 120V TR-SHPLF KTA1268BL P 100MI0A 120V TR-SHPLF KTC3200BL N 100MI0A 120V TR-SLPLF KTA1024 Y P 50MI0A -150V TR-SLPLF KTC3206 Y N 50MI0A 150V TR-SLPLF KTA1024 Y P 50MI0A -150V TR-SLPLF KTC3206 Y N 50MI0A 150V TR-SHPLF KTC3200BL N 100MI0A 120V TR-SLPLF KTC3206 Y N 50MI0A 150V TR-SLPLF KTA1024 Y P 50MI0A -150V
24
Ref. Designator
Q551 Q552 Q553 Q554 Q555 Q556 Q557 Q558 Q559 Q561 D481 D482 D568 IC101 IC481 IC482 IC483 IC484 IC485 IC486 IC487 Q425 Q426 Q433 Q434 Q435 Q436 Q437 Q438 Q439 Q440 Q513 Q517 Q518 Q519 Q520
Part Number
20556600 20556600 20556600 20508080 20508080 20508080 20508210 55133260 55179230 20647850 55179280 55179300 55125540 55142240 20832440 55124020 55125450 55123960 55123960 55123990 55179240 55179200 55179200 55179190 55179190 55179200 55179200 55179180 55179180 55179150 55179150 55179200 55179190 55179200 55179180 55179150
Qty
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC
Description
TR-SHPLF KTC3200BL N 100MI0A 120V TR-SHPLF KTC3200BL N 100MI0A 120V TR-SHPLF KTC3200BL N 100MI0A 120V TR-SLPLF KTC3198BL N 150MI0A TR-SLPLF KTC3198BL N 150MI0A TR-SLPLF KTC3198BL N 150MI0A TR-SLPLF KTA1266 Y P 150MI0A TR-SLPLF KTA1024 Y P 50MI0A -150V TR-SLPSWA KRC107M N TR-SHPLF KTA1268BL P 100MI0A 120V D-BRDLC BRIDGE BU8-04F FRONTIER D-BRDLC BRIDGE W2-04F FRONTIER D-BRDLC BU6-04F IC-OPERAMP NJM2068DD DUAL OP IC-REGPOSFXD KIA7815API NORMAL IC-REGNEGFXD KIA7915PI NORMAL IC-REGPOSFXD BA033T NORMAL IC-REGPOSFXD KIA7805API NORMAL IC-REGPOSFXD KIA7805API NORMAL IC-REGNEGFXD KIA7905PI NORMAL IC-REGULADJ KA337 TO-220 TR-SHPLF 2SC4883A N 2.0A TR-SHPLF 2SC4883A N 2.0A TR-SHPLF 2SA1859A P -2.0A TR-SHPLF 2SA1859A P -2.0A TR-SHPLF 2SC4883A N 2.0A TR-SHPLF 2SC4883A N 2.0A TR-SHPLF 2SC5358-R N 15.0A TR-SHPLF 2SC5358-R N 15.0A TR-SHPLF 2SA1986-R P -15.0A TR-SHPLF 2SA1986-R P -15.0A TR-SHPLF 2SC4883A N 2.0A TR-SHPLF 2SA1859A P -2.0A TR-SHPLF 2SC4883A N 2.0A TR-SHPLF 2SC5358-R N 15.0A TR-SHPLF 2SA1986-R P -15.0A
Resistors
R101 R102 R103 R104 R105 R106 R107 R108 R109 R110 R111 R112 R113 R114 R115 R116 R117 R118 R119 R120 R121 30939510 30939510 90571120 90571120 11059640 11059640 50882950 30939510 30939510 50882950 50882970 20469460 30939510 30939510 50882970 50882970 30939510 30939510 50882970 50882970 50882970 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC RCF 100K0 OHM +5% 250MI0W RCF 100K0 OHM +5% 250MI0W RCF 12K0 OHM +5% 250MI0W RCF 12K0 OHM +5% 250MI0W RCF 1K0 OHM +5% 250MI0W RCF 1K0 OHM +5% 250MI0W RCF 100R0 OHM +5% 250MI0W RCF 100K0 OHM +5% 250MI0W RCF 100K0 OHM +5% 250MI0W RCF 100R0 OHM +5% 250MI0W RCF 470R0 OHM +5% 250MI0W RCF 2K2 OHM +5% 250MI0W RCF 100K0 OHM +5% 250MI0W RCF 100K0 OHM +5% 250MI0W RCF 470R0 OHM +5% 250MI0W RCF 470R0 OHM +5% 250MI0W RCF 100K0 OHM +5% 250MI0W RCF 100K0 OHM +5% 250MI0W RCF 470R0 OHM +5% 250MI0W RCF 470R0 OHM +5% 250MI0W RCF 470R0 OHM +5% 250MI0W
25
Ref. Designator
R122 R123 R125 R126 R127 R128 R129 R130 R132 R401 R402 R403 R404 R405 R406 R407 R408 R409 R410 R411 R412 R413 R414 R415 R416 R417 R418 R419 R420 R421 R422 R423 R424 R425 R426 R427 R428 R429 R430 R431 R432 R433 R434 R435 R436 R437 R438 R439 R440 R441 R442 R443 R444 R445 R446 R447 R448 R449 R450 R451
Part Number
50882970 50882970 50882970 50882970 30939510 30939510 30939510 50882970 30939510 60441550 60441550 30939490 309