Text preview for : Sony-CDPS3 cd.pdf part of Sony CDPS3 cd
Back to : Sony-CDPS3 cd.pdf | Home
CDP-S3
SERVICE MANUAL
Ver 1.3 2002.12
AEP Model UK Model E Model Australian Model
CDP-S3 is the CD player section in MHC-S7AV or MHC-S3.
Model Name Using Similar Mechanism CD Mechanism Type Base Unit Name Optical Pick-up Name
NEW CDM63B-30BD60 BU-30BD60 OP Assy (A-MAX.3)
SPECIFICATIONS
System Laser Compact disc and digital audio system Semiconductor laser (=780 nm) Emission duration: continuous 2 Hz 20 kHz (±0.5 dB) More than 90 dB More than 90 dB
Frequency response Signal-to-noise ratio Dynamic range OPTICAL OUT (Square optical connector jack, rear panel) Dimensions (w/h/d) Approx. 280 x 108 x 330 mm Mass Approx. 2.7 kg Design and specifications are subject to change without notice.
COMPACT DISC PLAYER
9-873-831-14
2002L0500-1 C 2002.12
Sony Corporation
Home Audio Company Published by Sony Engineering Corporation
CDP-S3
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. NOTES ON LASER DIODE EMISSION CHECK The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pick-up block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens. LASER DIODE AND FOCUS SEARCH OPERATION CHECK Carry out the "S curve check" in "CD section adjustment" and check that the S curve waveforms is output three times. Notes on chip component replacement · Never reuse a disconnected chip component. · Notice that the minus side of a tantalum capacitor may be damaged by heat. Flexible Circuit Board Repairing · Keep the temperature of the soldering iron around 270 °C during repairing. · Do not touch the soldering iron on the same conductor of the circuit board. (within 3 times) · Be careful not to apply force on the conductor when soldering or unsoldering.
CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior.
Laser component in this product is capable of emitting radiation exceeding the limit for Class 1. The following caution label is located inside the unit.
SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
2
CDP-S3
TABLE OF CONTENTS 1. 2. 3.
3-1. 3-2. 3-3. 3-4. 3-5. 3-6. 3-7.
SERVICING NOTES ............................................... 4 GENERAL ................................................................... 5 DISASSEMBLY
Disassembly Flow ........................................................... Cover ............................................................................... CD Mechanism Deck (CDM63B-30BD60) ................... MAIN Board ................................................................... Front Panel Section ......................................................... PANEL (L) Board, PANEL (R) Board ........................... Lid (CD) .......................................................................... 6 7 7 8 8 9 9
4. 5. 6.
TEST MODE .............................................................. 10 ELECTRICAL ADJUSTMENTS ......................... 11 DIAGRAMS
12 14 15 16 17 18 19 20 21 24
6-1. Note for Printed Wiring Boards and Schematic Diagrams ................................................ 6-2. Printed Wiring Board BD Section ........................... 6-3. Schematic Diagram BD Section ............................... 6-4. Printed Wiring Boards CD CHANGER Section ..... 6-5. Schematic Diagram CD CHANGER Section ......... 6-6. Printed Wiring Board MAIN Section ...................... 6-7. Schematic Diagram MAIN Section ......................... 6-8. Printed Wiring Boards PANEL Section .................. 6-9. Schematic Diagram PANEL Section ....................... 6-10. IC Pin Function Description ...........................................
7.
EXPLODED VIEWS
26 27 28 29
7-1. General Section ............................................................... 7-2. CD Mechanism Deck Section-1 (CDM63B-30BD60) ....................................................... 7-3. CD Mechanism Deck Section-2 (CDM63B-30BD60) ....................................................... 7-4. Base Unit Section (BU-30BD60) ...................................
8.
ELECTRICAL PARTS LIST ............................... 30
3
CDP-S3 SECTION 1 SERVICING NOTES
This set is a component of the MHC-S7AV or MHC-S3. The MHC-S7AV or MHC-S3 system configuration is as shown below, and therefore it does not operate normally unless all four components are connected. In performing the repair, connect all components with the system cables. Note: The precaution to the users is described on the label stuck on the back panel (CD player) and in the troubleshooting section in the Operation Manual. System Configuration:
CD-TEXT TEST DISC
This unit is able to display the test data (character information) written in the CD on its fluorescent indicator tube. The CD-TEXT TEST DISC (TGCS-313:4-989-366-01) is used for checking the display. To check, perform the following procedure. Checking Method: 1. Press the I/1 button to turn the power on, set the disc to the disc table with the "test disc" label facing up, and chuck the disc. 2. Press the [CD] button to set CD function, and press the n N button to playback the disc. 3. The following will be displayed on the liquid crystal display. Display : 1KHZ/0DB/L R 4. Pressing the [-- .] or [> +] button, select the track. The text data of each track will be displayed. For details of the displayed contents for each track, refer to "Table 1 : CD-TEXT TEST DISC TEXT Data Contents". Restrictions in CD-TEXT Display In this unit, some special characters will not be displayed properly. These will be displayed as a space or a character resembling it. Table 1 : CD-TEXT TEST DISC TEXT Data Contents (TRACKS No. 1 to 20:Normal Characters) TRACK No. Displayed Contents 1kHz/0dB/L&R 20Hz/0dB/L&R 40Hz/0dB/L&R 100Hz/0dB/L&R 200Hz/0dB/L&R 500Hz/0dB/L&R 1kHz/0dB/L&R 5kHz/0dB/L&R 7kHz/0dB/L&R 10kHz/0dB/L&R 16kHz/0dB/L&R 18kHz/0dB/L&R 20kHz/0dB/L&R 1kHz/0dB/L&R 1kHz/1dB/L&R 1kHz/3dB/L&R 1kHz/6dB/L&R 1kHz/10dB/L&R 1kHz/20dB/L&R 1kHz/60dB/L&R
TA
POWER SUPPLY
AC IN
ST
SYSTEM & CD µcon DISPLAY
CDP TC
TC µcon
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
Note: Track No. 21 to 99 are not displayed.
4
CDP-S3 SECTION 2 GENERAL
Parts Identification
The items are arranged in alphabetical order. Refer to the pages indicated in parentheses ( ) for details.
This section is extracted from instruction manual.
Main unit
Remote Control
wj wkwl
e; ea
1 2 3
m
M
.
>
1
2
3
H
S
x
es ed
ek
ej
eh eg ef
es ea e; wl wk wj wh wg
H hH hH
. m
> M
x X
O P o p
4 5 6 7 8 9 q; qa qs qd qf qg qh qj
DISC 13 ek (14, 15, 21) DISC 13 indicators ej DISC 13 Z (eject) wl (14) PLAY MODE wj (14, 15, 21) REPEAT wk (14) N (play) eh (14, 15) X (pause) eg (14) x (stop) ef (14, 20) . (go back) ed (14, 15, 21) > (go forward) es (14, 15, 21) m (rewind) e; (14) M (fast forward) ea (14)
wf wd ws wa w; ql qk
CD H es (14, 15) CHECK 5 (15) CLEAR 6 (15) CLOCK/TIMER SELECT qj (30) CLOCK/TIMER SET qk (13, 21, 29) DBFB qg (23) DISPLAY ws (13, 16, 18, 29, 35) D.SKIP 4 (14) ENTER wg (10, 12, 13, 15, 17, 18, 21, 22, 2630) EQ qd (27) EQ ON/OFF qf (10, 28) FUNCTION wf (10, 14, 15, 20, 21, 31) GROOVE wa (23) SET UP qs (10, 12, 26, 28, 29) SLEEP 7 (29) SUR wd (25) TAPE A hH ea (19, 35) TAPE B hH e; (19, 20, 35) TUNER/BAND wl (17) TUNING + 9 (17) TUNING wh (17) TV CH +/ ql TV VOL +/ w; TV @/1 2 TV/VIDEO 1 VOL +/ qh BUTTON DESCRIPTIONS @/1 (power) 3 X (pause) q; x (stop) 8 . (go back) wk > (go forward) wj m (rewind) wh M (fast forward) 9 O/o/P/p qa
5
CDP-S3 SECTION 3 DISASSEMBLY
· This set can be disassembled in the order shown below.
3-1.
DISASSEMBLY FLOW
SET
3-2. COVER (Page 7)
3-3. CD MECHANISM DECK (CDM63B-30BD60) (Page 7)
3-4. MAIN BOARD (Page 8)
3-5. FRONT PANEL SECTION (Page 8)
3-6. PANEL (L) BOARD, PANEL (R) BOARD (Page 9)
3-7. LID (CD) (Page 9)
6
CDP-S3
Note: Follow the disassembly procedure in the numerical order given.
3-2.
COVER
3 cover
2 screw (BVTT3 × 6)
1 two screws (case 3 TP2)
1 two screws (case 3 TP2)
3-3.
CD MECHANISM DECK (CDM63B-30BD60)
4 CD mechanism deck (CDM63B-30BD60)
2 connector (CN701)
3 four screws (BVTP3 × 8)
1 wire (flat type) (21 core) (CN301)
7
CDP-S3
3-4.
MAIN BOARD
2 two connectors (CN101, 102)
1 wire (flat type) (21 core) (CN301)
5 MAIN board
2 connector (CN401)
3 screw (BVTP3 × 8) 3 two screws (BVTP3 × 8)
4 lug
2 connector (CN701)
3 screw (BVTP3 × 8)
3-5.
FRONT PANEL SECTION
1 connector (CN401)
3 claw 4 front panel section
3 two claws 2 three screws (BVTP3 × 8)
8
CDP-S3
3-6.
PANEL (L) BOARD, PANEL (R) BOARD
4 four screws (BVTP2.6 × 8) 6 PANEL (R) board
5 two claws 1 five screws (BVTP2.6 × 8)
3 PANEL (L) board
2 two claws
3-7.
LID (CD)
2 bracket (LID) assy
1 screw (BVTP2.6 × 8)
4 spring (CD)
3 lid (CD)
9
CDP-S3 SECTION 4 TEST MODE
Note: Use flowing buttons in the test mode. no mark : Button of CD unit (CDP-S3) *1 : Button of amplifier unit (TA-S7AV or TA-S3) *2 : Button of tuner unit (ST-S5 or ST-S3)
[CD Delivery Mode] · This mode moves the optical pick-up to the position durable to vibration. Use this mode when returning the set to the customer after repair. Procedure: 1. Press the I/1 *1 button to turn the power on. 2. Turn the [FILE SELECT] *1 knob to set the CD function. 3. While pressing the [EQ ON/OFF] *1 button, press the I/1 *1 button. 4. The message "LOCK" is displayed on the fluorescent indicator tube of tuner unit and turn the power off automatically, and the CD delivery mode is set. [GC Test Mode] Enter the GC Test Mode Procedure 1: 1. Press the I/1 *1 button to turn the power on. 2. While pressing the both [PLAY MODE] and [x] buttons, press the [Z] (DISC 1) button. 3. LEDs and fluorescent indicator tube are all turned on of all units. Procedure 2: 1. Press the I/1 *1 button to turn the power on. 2. While pressing the both [STEREO/MONO] *2 and [CINEMA STUDIO C] *1 buttons, press the [CLOCK/TIMER] *2 button. 3. LEDs and fluorescent indicator tube are all turned on of all units. Version Display Mode Procedure: 1. Enter the GC test mode. 2. Each time the [DISC 1] or [TUNER MEMORY] *2 button is pressed, microcomputer or mechanism deck version is displayed of each unit. 3. Press the [DISC 3] or [TUNING +] *2 button to detail is displayed the version. Key Check Mode Procedure: 1. Enter the GC test mode. 2. Press the [DISC 2] or [TUNING --] *2 button to set the key check mode, and displays "K 0 J 0 V 0" on the fluorescent indicator tube of tuner unit. 3. All buttons are pressed of CD unit, all LEDs are blinking of CD unit. (not change the display of fluorescent indicator tube) Releasing the GC Test Mode To release from this mode, press three buttons in the same manner as entering this mode or disconnect the power cord.
[CD Service Mode] · This mode can run the CD sled motor optionally. Use this mode, for instance, when cleaning the optical pick-up. Procedure: 1. Press the I/1 *1 button to turn the power on. 2. Turn the [FILE SELECT] *1 knob to set the CD function. 3. While pressing the both [PLAY MODE] and [x] buttons, press the [.] button. 4. Set to the CD service mode. 5. With the CD in stop status, press the [M] button to move the optical pick-up to outside track, or press the [m ] button to inside track. 6. To release from this mode, perform as follows. 1) Move the optical pick-up to the most inside track. 2) Disconnect the power cord.
Notes: · Always move the optical pick-up to most inside track when releasing from this mode. Otherwise, a disc will not be unloaded. · Do not run the sled motor excessively, otherwise the gear can be chipped.
[CD Cancellation Mode of Repeat Limitation] · This mode can cancel the CD repeat limitation (5 times). Procedure: 1. Press the I/1 *1 button to turn the power on. 2. Turn the [FILE SELECT] *1 knob to set the CD function. 3. While pressing the both [PLAY MODE] and [x] buttons, press the [REPEAT] button. 4. CD repeat limitation is canceled. 5. To release this mode, disconnect the power cord.
10
CDP-S3 SECTION 5 ELECTRICAL ADJUSTMENTS
Note :
E-F Balance (1 Track jump) Check
oscilloscope BD board TP(TEO) TP(DVC)
1. CD Block is basically designed to operate without adjustment. Therefore, check each item in order given. 2. Use LUV-P01 (4-999-032-01) unless otherwise indicated. 3. Use an oscilloscope with more than 10M impedance. 4. Clean the object lens by an applicator with neutral detergent when the signal level is low than specified value with the following checks. S-Curve Check
Oscilloscope BD board TP(FEO) TP(DVC)
Procedure : 1. Connect an oscilloscope to TP (TEO) and TP (DVC). 2. Turn Power switch on. 3. Load a disc (LUV-P01) and playback the number nine track. 4. Press the N button. (Becomes the 1 track jump mode.) 5. Confirm that the level B and A (DC voltage) on the oscilloscope waveform.
1 track jump waveform center of waveform B A (DC voltage) DVC level=1.0 ±0.5Vp-p symmetry
Procedure : 1. Connect an oscilloscope to TP (FEO). 2. Connect between TP (FEI) and TP (DVC) ( 1.65 V) by lead wire. 3. Turn Power switch on. 4. Load a disc (LUV-P01) and actuate the focus search. (In consequence of open and close the disc tray, actuate the focus search) 5. Confirm that the oscilloscope waveform (S-curve) is symmetrical between A and B. And confirm peak to peak level within 2 ± 0.5 Vp-p.
S-curve waveform symmetry
6. Adjust RV101 on the BD board so that the center of waveform becomes the same voltage of DVC. (i.e. A=0V) Adjustment Location: [BD BOARD] (Conductor Side)
A within 2 ±0.5Vp-p B
6. After check, remove the lead wire connected in step 2.
Note : · Try to measure several times to make sure than the ratio of A : B or B : A is more than 10 : 7. · Take sweep time as long as possible and light up the brightness to obtain best waveform.
RF Level Check
BD board TP(RFDC) TP(RFAC) TP(DVC) oscilloscope
TP (DVC) TP 1 (RFAC) 15 IC103 16 30 TP (FEO) TP TP (TEO) (FEI) 40 41 TP (RFDC)
21 20 1 80
IC101
60 61
Procedure : 1. Connect an oscilloscope CH1 to TP (RFDC) and CH2 to TP (RFAC). 2. Turn Power switch on. 3. Load a disc (LUV-P01) and playback. 4. Confirm that oscilloscope waveform is clear and check if RF signal level is correct or not.
Note : Clear RF signal waveform means that the shape " " can be clearly distinguished at the center of the waveform.
RV101
RF signal waveform VOLT/DIV : 200mV TIME/DIV : 500ns
level : 0.65 ±0.15Vp-p (RFDC) 1.1 ±0.4Vp-p (RFAC)
11
CDP-S3 SECTION 6 DIAGRAMS
6-1. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block)
Note on Schematic Diagram: · All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics and tantalums. · All resistors are in and 1/4 W or less unless otherwise specified. f · : internal component. · C : panel designation. Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. · A : B+ Line. · Voltages are taken with a VOM (Input impedance 10 M). Voltage variations may be noted due to normal production tolerances. · Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production tolerances. · Circled numbers refer to waveforms. · Signal path. J : CD PLAY
Note on Printed Wiring Boards: · X : parts extracted from the component side. · Y : parts extracted from the conductor side. f : internal component. · · : Pattern from the side which enables seeing. · Indication of transistor.
C Q B E These are omitted.
Q B C E These are omitted.
12
CDP-S3
· Circuit Boards Location
PANEL (R) board MAIN board
PANEL (L) board
TRAY SENSOR board IN OUT SW board
BD board
DRIVER board
MOTOR board DISC SENSOR board
13
CDP-S3
6-2.
PRINTED WIRING BOARD BD Section · See page 13 for Circuit Boards Location.
(Page 18)
A
MAIN BOARD CN301
M102 (SLED) M101 (SPINDLE)
TP (RFDC)
TP (DVC)
TP (RFAC) TP (FEI)
· Semiconductor Location
Ref. No. D101 IC101 IC102 IC103 Q101 Q102 Location B-3 C-3 B-2 D-2 C-1 A-3
There are a few cases that the part printed on this diagram isn't mounted in this model.
14
TP (TEO)
TP (FEO)
CDP-S3
6-3. SCHEMATIC DIAGRAM BD Section · See page 22 for Waveforms. · See page 22 for IC Block Diagrams.
TP (DVC)
TP (RFDC)
IC B/D
TP (TEO)
TP (FEI)
TP (RFAC)
IC B/D
TP (FEO)
IC B/D
A
MAIN BOARD CN301
(Page 19)
Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
· Voltages and waveforms are dc with respect to ground under no-signal conditions. no mark : CD PLAY
15
15
CDP-S3
6-4.
PRINTED WIRING BOARDS CD CHANGER Section
· See page 13 for Circuit Boards Location.
1
5
MAIN BOARD NO202
(Page 18)
There are a few cases that the part isn't mounted in model is printed on diagrams.
16
16
CDP-S3
Ver 1.1
6-5.
SCHEMATIC DIAGRAM CD CHANGER Section
· See page 22 for IC Block Diagram.
RPI-321
IC731 SUB TRAY1 HEIGHT SENSOR
RPI-321
IC732 SUB TRAY2 HEIGHT SENSOR
RPI-321
IC733 SUB TRAY3 HEIGHT SENSOR
B
MAIN BOARD NO202
(Page 19)
IC751 DISC IN DETECT
· Voltages and waveforms are dc with respect to ground under no-signal conditions. no mark : CD STOP
17
17
CDP-S3
6-6.
PRINTED WIRING BOARD MAIN Section
· See page 13 for Circuit Boards Location.
1
2
(Page 14)
3
A
BD BOARD CN101
4
5
6
(Page 16)
7
B
DRIVER BOARD CN701
8
SYSTEM CONTROL 3 TO ST-S3/S5
9
10
C321 FB305
CD303
A
MAIN BOARD
C318 C316 C118
1
JW158
JW137
FB314
1 12
JW141
JW139
JW138 FB315 NO202 R484 R486
IC503
C532
3
C116
C302 JW175
FB311 L310 FB312
FB310
C304
C319
C317
CN301
JW143
JW140
JW142
JW154
JW112
JW111
JW110
JW109
CD311
1
14
JW108
R403 R401
JW178
CLP102
(CHASSIS)
C303
C523
1
JW172
R440
C320 R437 C313
C311
JW132
CD302 CD301 R426 R419
JW130
C531 VCD101
8
JW151
CN102
JW135
C301
1 2
CD313
9
CD312
C314
R428 R432 R438
R424
JW159
JW155 JW156 JW157 JW165
C310 CD304 R443
C306
JW161
C315
FB313
IC402
JW120
R417 R413 C462
C255 R402 C411 C401 JW136 R411 C425
C260
JW160
JW107
R436
R430
JW103
B
R429
1
8
C261
D514 D123
JW102
C251
R485
R487
CN103
SYSTEM CONTROL 5 TO TC-S3
D513
D515
JW127
JW114
JW134 JW133
JW129
JW163
JW128
JW126
JW125
JW113
C524 C522
C501
R435
JW145
JW144
C416 X401
C427
JW122 JW123
JW153
R433
1
JW124 C513
IC502
15 3
14
Q501
JW164
JW162
R460 R441 R442 R456 FB410 R445 R453 C499
C
CN401
R409
R425 JW171
C521 R427 R482 R412 R491 JW98 D511 R489 JW121
E Q502 E 1
C498
R465 R469 R473 R477 R457 R447 R450 R444 R448 JW148 R451 R500 R492 C463 R497 R483
R494
JW100
IC401
R134
D504
D502
C500
L125 R123 C125
R490
JW106
JW104
JW99 JW131 FB416 R132 JW119 JW118
CN101 D512
9
JW169
JW168
D503
D501 C103 C102
C122
C124
3
JW177
JW176
R481
JW170
JW150
JW149
JW147 JW146 R480
JW167
IC102
OPTICAL OUT TO ST-S3/S5
1
JW117 JW116
D
R452
R446
R449
R459
R495
R496
JW115
R493
R133
D105 C107
1
C101
CLP101
11 1-680-994(21)
C
PANEL (L) BOARD NO703
(Page 20)
· Semiconductor Location
Ref. No. D103 D104 D105 D123 D501 D502 D503 D504 D511 D512 D513 D514 Location D-9 D-9 D-7 B-8 C-9 C-9 C-9 C-9 C-8 D-7 B-8 B-8 Ref. No. IC102 IC401 IC402 IC502 IC503 Q501 Q502 Location D-10 C-4 B-5 C-8 B-8 C-8 C-8
18
18
CDP-S3
6-7. SCHEMATIC DIAGRAM MAIN Section · See page 22 for Waveform.
OPTICAL OUT TO ST-S3/S5
GND
+3.3V
SIG
CN301 21P PWM3 PWM2 PWM1 DVDD DOUT DGND LOUT AGND ROUT FB312 C301 0.47 50V CD301 CD302 CD303 FB310 24 26 28 CD304 FB305 FB311 C310 0.022 FB410
IC102 TOTX140
C122 0.022 C103 0.1 D502 11ES2 D123 MTZA-2.2A D503 11ES2 C501 4700 16V D504 11ES2 D501 11ES2 C102 0.1 C101 0.1
CLP102
C302 0.0047 C303 0.01 C304 0.022
C125 220 10V C124 0.1 R123 100
OPTICAL TRANSCEIVER L125 220µH
(CHASSIS)
CN101 9P C500 0.1 AC AC HESO-GND HESO-GND EVER+5V SYSTEM CONTROL 3 TO ST-S3/S5
D511 11ES2
Q501 RT1P137S
AVDD XRST DATA C311 0.01 C320 0.01 C313 220p C314 100p C315 100p C316 100p C317 100p C318 100p C319 100p
FB313 CD311 CD312 CD313 43 35 42 37 40 A32 A36 33 A19 C306
Q501,502 B+ SWITCH
D512 11ES2 D105 1SS133 D513 11ES2 +5.6V REGULATOR O G C524 220 10V C523 220 10V D514 11ES2 C522 470 10V I D515 11ES2 C107 JW
MRESET TP107 V-MUTE I2C-DATA I2C-CLK
(Page 15)
XLT CLOK LDON SQSO SENS SQCK SCOR MGND +7V
Q502 BA1A4M
C513 470 10V
IC502 TA78057S
C521 0.1
CN102 8P JW98 100 JW99 100 DGND(TC) VCD101 UNREG(TC) MGND(TC)
L310 5.6µH FB314 C321 0.022 C532 470 10V
+7V REGULATOR MGND(TC) O G FB315 IC503 TA7807S C531 0.1 C116 1k VCD R-IN AGND(CD) C118 1k VCD L-IN 52 47 I SHASSIS GND
NO202 12P DISC-SENS IN-SW OUT-SW TRAYSENS3 TRAYSENS2 TRAYSENS1 DGND D+5V C255 0.022 45 44 C463 10 50V
59 51 53 52
C261 C260
0.022 0.022
46 50 49
38 12 29 30
48
FB416
(Page 17)
LOD-POS LOD-NEG MGND M+7V C251 0.022
R453 100
R452 100
R500 10k
R460 10k
R459 100
TP460 TP458 TP457
R451 100
TP456
73
77
69
65
TP463
TP461
R132 75k R457 10k R456 10k
R134 1k
C462 0.022
R133 75k
CN103 15P DGND
C401 0.022
A-TRIG ECO CHECK LED_DISC1 LED_DISC2 LED_DISC3 LED_DISC2 LED_DISC2 LED_DISC2 LED_DISC1 LED_DISC1 LED_DISC1 PLAY LED_PLAY VSS LED_DISC3 LED_DISC3 LED_PLAY LED_DISC3 VCC R/PB/PAS B-TRIG LED_ DISC-SENS SOFT-TEST
91 90 LED_ 89 59 R450 100 T-SENS3 R449 100 T-SENS2 R448 100 LED_PAUSE EXP-IN DATA 85 86 87 R485 100 EXP-OUT DATA R486 100 EXP-LAT R487 100 EXP-CLK 89 R489 100 R490 100 B-SHUT 91 R491 100 B-HALF R493 150 R492 4.7k R482 10k 94 95 R494 100 KEY2(TC) R495 100 KEY1(CD) R483 10k 97 R497 100 KEY0(CD) VREF R496 10k
BU PWM 2 BU PWM 1 BU PWM 3
BHALF BSHUT ASHUT REC/PB/PAS DATA-OUT DATA-IN SYSTEM CONTROL 5 CLK LAT KEY2 BTRIG ATRIG UNREG TO TC-S3
A32
A36
A19
PLAY 81
50 85 49 84 48 87 47 86 46 94 45 53 44 51 43 42 MGND
LED_PAUSE LED_PAUSE R484 100 R480 100k
R403 100
R402 100
R401 100
T-SENS1 R447 100 CLOSE R446 100 OPEN R445 100 LOAD-OUT R444 100 LOAD-IN R443 100 XRST R442 100 XLT R441 10k
84
LED_PAUSE A-SHUT
LEVEL SHIFT IC402 SN74HCT04ANS -E05
90
SGND SYSTEM CONTROLLER IC401 M30620MAA-B31FP CD POWER R437 100 CD-CLK R436 100 SENS R435 100 35 CD-DATA RTS1 R433 100 SQ-CLK SQDATA-IN
IIC-CLK DATA
R440 100 HOLD TP439 R438 100
40
MODEL-IN TP493 KEY3
38 37 36
32
36
19
AVSS
33 32
R432 100
AVCC
CNVSS RESET
X-OUT
BYTE
X-IN
VSS
VCC
97
TP401 TP402 TP403 TP404 TP405 TP406
TP411
TP418 TP420 TP421 TP422 TP423 TP425 TP407 TP427
95
R429 100
CN401 9P
IIC-
C499 0.022
SCOR
C498 0.022
TP500
NMI
R413 330
X401 16MHz
C425 100p R430 100 R425 4.7k R427 4.7k C427 100p
R481 150 R477 150 R473 150 R469 150
81 77 73 69 65 R409 10k R411 100
12
R417 10k
R419 100
R424 2.2k
R426 220k
R428 100k
24
26
28
29
(Page 21)
R465 150
C411 1 50V
R412 10k
C416 10 50V
19
30
19
19
Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
· Voltages and waveforms are dc with respect to ground under no-signal conditions. no mark : CD PLAY
CDP-S3
6-8.
PRINTED WIRING BOARDS PANEL Section
(Page 18)
· See page 13 for Circuit Boards Location.
C
MAIN BOARD CN401
PANEL (R) BOARD
9 1 NO703 R712 R711 R710
m REPEAT S707 PLAY MODE
S712
M
S711
S708
R706
> . Z (DISC 3) Z Z (DISC 1)
R707 R704
R705
S713
S714
PANEL (L) BOARD
S706 R713 D701 D702 D702, S717 R715
N
(DISC 2)
S705
S704
D703
D704
D705
1 2
NO701
1 2
DISC 3 DISC 2 DISC 1
NO702
3
2
1
R700
S701
R701
S702
R702
S703
R703
S715 x
S716 R714 D701, S716
X
R716
S717
11 1-680-995(21) 1-680-996-
11 (21)
20
20
CDP-S3
6-9.
SCHEMATIC DIAGRAM PANEL Section
R707 1.8k
R706 1.2k
R705 1k
R704 680
R703 560
R702 470
R701 330
R700 270
S708
S707
S706
S705
S704
S703
S702
S701
CN701 2P
PLAY MODE
REPEAT (DISC 3) (DISC 2) (DISC 1)
DISC 1
DISC 2
DISC 3
R716 1.2k
R715 1k
R714 680
R713 560
R712 470
R711 330
R710 270
S717
S716
S715
S714
S713
S712
S711
CN702 2P
CNW703 9P
D701 SEL5923A
(Page 19)
D702 SEL5423E
D703 SEL5923A
D704 SEL5923A
D705 SEL5923A
21
21
CDP-S3
· Waveforms BD Board
1 IC101 ta (RFAC) (CD Play mode)
MAIN Board
qa IC401 qd (X-OUT)
· IC Block Diagrams BD Board IC101 CXD3017Q
VDD VSS AVDD3 AVSS3 AVDD0 RFAC BIAS ASYI ASYO AVSS0 DOUT PCO FILI FILO CLTV RFDC CE TE IGEN ADIO
60
59 58 57
56 55 54 53
52
51 50 49 48
47
46 45
44
43 42 41 40 SE 39 FE 38 VC OPERATIONAL AMPLIFIER ANALOG SWITCH A/D CONVERTER
1.1 Vp-p
2.6 Vp-p
INTERNAL BUS
DIGITAL OUT
ERROR CORRECTOR 16K RAM
DIGITAL PLL
ASYMMETRY CORRECTOR
LRCK 61 PCMD 62 D/A INTERFACE BCK 63 EMPH 64 XVDD 65 XTAI XTAO XVSS AVDD1 AOUT1 AIN1 66 67 68 69 70 71 TIMING LOGIC
EFM DEMODULATOR
63 ns
2 IC101 ra (TE) (CD Play mode)
CLOCK GENERATOR SERVO DSP FOCUS SERVO TRACKING SERVO PWM GENERATOR FOCUS PWM GENERATOR TRACKING PWM GENERATOR SLED PWM GENERATOR
Approx. 0.4 Vp-p
37 XTSL 36 TES1 35 TEST 34 VSS 33 32 31 30 29 28 FRDR FFDR TRDR TFDR SRDR SFDR
LOUT1 72 AVSS1 73 AVSS2 74 LOUT2 75 PWM PWM
SUBCODE PROCESSOR
SLED SERVO
3rd ORDER NOISE SHAPER
27 SSTP SERVO INTERFACE DIGITAL CLV MIRR, DFCT, FOK DETECTOR 26 MDP 25 LOCK 24 FOK 23 DFCT 22 MIRR
3 IC101 el (FE) (CD Play mode)
AIN2 76 AOUT2 77 AVDD2 78 OVER SAMPLING DIGITAL FILTER
SERVO AUTO SEQUENCER
Approx. 0.3 Vp-p
RMUT 79 LMUT 80
SERIAL IN INTERFACE
CPU INTERFACE
21 COUT
1 2
SQSO SQCK
3
XRST
4
SYSM
5 6 7 8
DATA XLAT CLOK SENS
9 10 11 12 13 14 15 16 17 18 19 20
WFCK XUGF XPCK GFS SCLK VDD ATSK SPOA SPOB XLON C2PO SCOR
CH3OUTR
4 IC101 wh (MDP)
IC102
PRFVCC
BA5974FM-E2
CH4OUTR CH3OUTF MUTE GND CH4OUTF
15 14
2.5 Vp-p
28
27
26
25
24
23
22
21
20
19
POWVCC
CAPAIN3
CH4SIN'
CH3RIN
CH4BIN
CH4SIN
CH3FIN
18
17
16
F
R R MUTE
INTERFACE F
7.5 µs
LEVEL SHIFT
F INTERFACE F R R INTERFACE F R R F
THERMAL SHUTDOWN
1
2
3
4
5
6
7
8
9
10
11
12
13
VREFOUT
CH1FIN
CH1RIN
CH2FIN
CH2RIN
VREFIN
POWVCC
CH2OUTR
CH2OUTF
CH1OUTR
22
22
CH1OUTF
CAPAIN1
CAPAIN2
GND
CDP-S3
DRIVER Board IC103 CXA2581N-T4
RW/ROM 30 DC OFST 29 RFDCI + + 28 RFDCO
IC701
BA6956AN
TSD
A B C D DVC
DVC VCC VC
CONTROL LOGIC
1
27 VC
2
OUT2
3
RNF
4
OUT1
5
VM
6
VCC
7
FIN
8
GND
9
RIN
VC
VC LD PD 1 EQ 2 APC AMP 26 RFC 25 VFC 24 BST
EQ IN
3 RW/ROM RFAC SUMMING AMP
AC SUM
4
A A B C D D
A B C D
6 7 8 9
A B C D
DVC VC RW/ROM RW/ROM 19 TE BAL
E 10
GM + 18 TE
F 11
GM VC
SW 12 DVCC 13
APC-OFF (Hi-Z) RW/ROM (H/L) B DVC D A C
RW/ROM RW/ROM
VOFST + +
DVC 14
DVC VC RW/ROM RFAC 15
+
GND
5
+
+
DVC
VOFST
RW/ROM
EQ ON/OFF RFAC VCA VCC B C VOFST 23 RFG 22 VCC 21 CEI
20 CE
17 FEI
16 FE
VREF
23
CDP-S3
6-10.
IC PIN FUNCTION DESCRIPTION
Pin Name -- BYTE CNVSS -- -- RESET X-OUT VSS X-IN VCC NMI -- SCOR -- BU PWM 3 -- BU PWM 2 -- BU PWM 1 IIC-CLK IIC-DATA -- SQ-DATA-IN SQ-CLK RTS1 CD-DATA SENS CD-CLK CD POWER -- HOLD -- XLT XRST LOAD-IN LOAD-OUT OPEN CLOSE T-SENS1 T-SENS2 I/O -- I -- -- -- I O -- I -- I -- I -- O -- O -- O I/O I/O -- I O -- O I O O -- O -- O O O O I I I I Not used (open) External data bus line byte selection signal input "L": 16 bits, "H": 8 bits Not used (fixed at "L") To flash memory connector Not used (fixed at "L") Not used (open) Reset signal input from the tuner unit (ST-S3/S5) System clock output terminal (16 MHz) Ground terminal System clock input terminal (16 MHz) Power supply terminal (+5V) Non-maskable interrupt input terminal (fixed at "H" in this set) Not used (open) Subcode sync (S0+S1) detection signal input from the CXD3017Q (IC101) Not used (open) RFDC PWM signal output to the CXA2581N (IC103) Not used (open) Tracking error PWM signal output to the CXA2581N (IC103) Not used (open) Focus error PWM signal output to the CXA2581N (IC103) Communication data reading clock signal input or transfer clock signal output with the tuner unit (ST-S3/S5) Communication data bus with the tuner system (ST-S3/S5) Not used Subcode Q data input from the CXD3017Q (IC101) Subcode Q data reading clock signal output to the CXD3017Q (IC101) Not used CD decode data output to the CXD3017Q (IC101) Internal status (SENSE) signal input from the CXD3017Q (IC101) Serial data transfer clock signal output to the CXD3017Q (IC101) Power on/off control signal output for the CD mechanism deck section "L": standby, "H": power on Not used (open) Automatic power control hold signal output to the CXA2581N (IC103) Not used (fixed at "L") Serial data latch pulse output to the CXD3017Q (IC101) Reset signal output to the CXD3017Q (IC101) Loading motor drive signal (load-in direction) output the motor driver (IC701) Loading motor drive signal (load-out direction) output the motor driver (IC701) Sub tray load in/out detect switch (S742) input "L": sub tray is chucking position Sub tray load in/out detect switch (S742) input "L": sub tray slides out of chucking position Detection input from the disc tray 1 height sensor (IC731) "H": disc tray 1 position is chucking position Detection input from the disc tray 2 height sensor (IC732) "H": disc tray 2 position is chucking position Description
· MAIN BOARD IC401 M30620MAA-B31FP (SYSTEM CONTROLLER) Pin No. 1 to 7 8 9 10 11 12 13 14 15 16 17 18 19 20 to 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49
24
CDP-S3
Pin No. 50 51 52 53 54 55 56 to 58 59 60, 61 62 63 64 65 to 68 69 to 72 73 to 76 77 to 80 81 to 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100
Pin Name T-SENS3 -- DISC-SENS B-TRIG ECO CHECK A-TRIG -- R/PB/PASS -- VCC SOFT-TEST VSS LED_DISC1 LED_DISC2 LED_DISC3 LED_PLAY LED_PAUSE EXP-IN DATA
EXP-OUT DATA
I/O I -- I O -- O -- O -- -- O -- O O O O O I O O O O I I I I -- I I -- I I -- --
Description Detection input from the disc tray 3 height sensor (IC733) "H": disc tray 3 position is chucking position Not used (fixed at "H") Detection input from the disc in detect sensor (IC751) Deck-B trigger plunger drive signal output to the tape deck unit (TC-S3) "H": trigger plunger on Not used (fixed at "H") Deck-A trigger plunger drive signal output to the tape deck unit (TC-S3) "H": trigger plunger on Not used (open) Recording/playback/pass selection signal output to the tape deck unit (TC-S3) "L": recording, center voltage: playback, "H": pass Not used (open) Power supply terminal (+5V) For software check terminal Ground terminal LED drive signal output of the 1 indicator (D705) "L": LED on LED drive signal output of the 2 indicator (D704) "L": LED on LED drive signal output of the 3 indicator (D703) "L": LED on LED drive signal output of the N indicator (D702) "L": LED on LED drive signal output of the X indicator (D701) "L": LED on Serial data input from the tape deck unit (TC-S3) Serial data output to the tape deck unit (TC-S3) Serial data latch pulse signal output to the tape deck unit (TC-S3) Serial data transfer clock signal output to the tape deck unit (TC-S3) LED drive signal output of the X indicator (D701) "L": LED on Shut off (desk-A) detection signal input from the tape deck unit (TC-S3) Shut off (desk-B) detection signal input from the tape deck unit (TC-S3) Detection input from the deck-B cassette detect switch of the tape deck unit (TC-S3) "L": cassette in Model destination setting terminal Not used (open) Key input from the tape deck unit (TC-S3) (A/D input) Key input terminal (A/D input) (S711 to S717) m, M , ., >, x, X, N keys input Ground terminal (for A/D conversion) Key input terminal (A/D input) (S701 to S708) DISC 3, DISC 2, DISC 1, Z (DISC1), Z (DISC2), Z (DISC3), REPEAT, PLAY MODE keys input Reference voltage (+5V) input terminal (for A/D converter) Power supply terminal (+5V) (for A/D conversion) Not used (open)
EXP-LAT EXP-CLK LED_PAUSE A-SHUT B-SHUT B-HALF MODEL-IN KEY3 KEY2 (TC) KEY1 (CD) AVSS KEY1 (CD) VREF AVCC --
25
CDP-S3 SECTION 7 EXPLODED VIEWS
NOTE: · -XX and -X mean standardized parts, so they may have some difference from the original one. · Color Indication of Appearance Parts Example: KNOB, BALANCE (WHITE) . . . (RED) Parts Color Cabinet's Color · Items marked "*" are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. · The mechanical parts with no reference number in the exploded views are not supplied. The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
7-1. GENERAL SECTION
8
#2
10 7 9 11 7
not supplied #1
CDM63B-30BD60 #1 not supplied
1 5
not supplied
#1
12 4
not supplied
4
6
#1
13 14 4
not supplied
3 2
#1
Ref. No. 1 2 3 4 5 6 7 8 9 Part No. X-4953-613-1 4-233-136-01 4-233-147-01 4-951-620-01 1-680-996-11 1-680-995-11 3-363-099-21 4-233-134-11 1-823-055-11 Description PANEL ASSY, FRONT LID (CD) SPRING (CD) SCREW (2.6X8), +BVTP PANEL (R) BOARD PANEL (L) BOARD SCREW (CASE 3 TP2) COVER WIRE (FLAT TYPE) (21 CORE) Remark Ref. No. 10 11 12 12 12 13 14 #1 #2 Part No. A-4725-658-A 1-757-633-11 4-233-135-01 4-233-135-11 4-233-135-31 3-970-608-01 4-965-822-01 7-685-646-79 7-685-871-01 Description MAIN BOARD, COMPLETE CORD (WITH CONNECTOR) 17P PANEL, BACK (AEP, UK) PANEL, BACK (Korea, Australian) PANEL, BACK (Mexican) SUMITITE (B3), +BV FOOT SCREW +BVTP 3X8 TYPE2 N-S SCREW +BVTT 3X6 (S) Remark
not supplied
26
CDP-S3
Ver 1.3
7-2. CD MECHANISM DECK SECTION-1 (CDM63B-30BD60)
B
506
B
505 507 501 506 509
not supplied
501
not supplied
519
508 501
not supplied
A
510 501 501 501 521 518
not supplied
509
512
514
511 516 515 517 524 501 513 520 501
504
502 522 501 501
503 523
501 501
not supplied
501
not supplied
A
525 501
Ref. No. 501 502 503 504 505 506 507 508 509 510 511 512 513 Part No. 4-218-253-01 4-228-996-01 4-228-995-01 4-228-972-02 4-231-971-01 4-985-672-01 4-228-414-01 4-228-980-01 4-228-981-02 4-228-963-01 Description SCREW (M2.6), +BTTP SPRING (R), TORSION SPRING (L), TORSION TRAY (MAIN) PULLEY (30B), CHUCKING SCREW (+PTPWH M2.6), FLOATING BRACKET (YOKE) SPRING (STOCKER), LEAF STOPPER (TRAY) SLIDER (STOCKER. L) Remark Ref. No. 514 515 516 517 518 519 520 521 522 523 524 525 Part No. 4-228-975-02 4-228-978-02 4-228-970-12 4-228-970-22 X-4953-307-1 4-234-423-01 1-678-457-11 4-228-986-02 4-228-990-03 4-228-991-03 Description COVER (TRAY. L) COVER (TRAY. R) TRAY (SUB) TRAY (SUB) PULLEY (A) ASSY, CHUCKING SPRING (STOCKER L), LEAF TRAY SENSOR BOARD RACK (TRAY.L) LEVER (SUB.L) LEVER (SUB.R) Remark
4-228-964-01 SLIDER (STOCKER. R) 4-228-970-02 TRAY (SUB) 4-229-001-01 HOLDER (SENSOR)
4-228-987-02 RACK (TRAY.R) 4-228-993-05 SLIDER (LOADING)
27
CDP-S3
7-3. CD MECHANISM DECK SECTION-2 (CDM63B-30BD60)
563
567
580 561 556 560 562 558 561 560 559 551
not supplied
574
BU-30BD60
553 575
561
561 560
553
565 551 553
A
556
579
551 562 564
569 568
566
A
578 556 557 556 557 576 578
not supplied
572 573 577 555 577
not supplied
551
552
554 551 553 551 552 551
Remark Ref. No. 567 568 569 570 571 572 573 574 575 576 577 578 579 580 M721 Part No. 4-228-968-01 4-228-998-01 4-228-976-01 1-678-461-11 X-4952-971-2 4-228-999-02 4-229-000-02 4-227-899-01 4-229-003-01 4-228-988-01 4-218-253-61 4-218-253-71 1-678-462-11 1-678-463-11 1-541-632-12
M721
571 570 556
Description BELT GEAR (DETECTION) SLIDER (BU. R) MOTOR BOARD MOTOR ASSY LEVER (MAIN. L) LEVER (MAIN. R) SCREW (DIA. 12), FLOATING PULLEY CHASSIS SCREW (M2.6), +BTTP SCREW (M2.6), +BTTP IN OUT SW BOARD DISC SENSOR BOARD MOTOR, DC (LOADING) Remark
Ref. No. 551 552 553 554 555 556 557 558 559 560 561 562 563 564 565 566
Part No. 4-985-672-01 4-229-002-02 4-218-254-21 4-228-971-01 4-228-974-02 4-218-253-01 4-228-969-02 4-228-977-01 4-951-620-01 4-227-045-11 4-231-451-01 4-231-151-01 4-231-517-03 4-228-985-01 4-228-997-02
Description SCREW (+PTPWH M2.6), FLOATING GEAR (SLIDER) SCREW (M2.6), +PTPWH CAM RACK (CENTER) SCREW (M2.6), +BTTP SPRING (TABLE), LEAF SLIDER (BU. L) SCREW (2.6X8), +BVTP SPRING (INSULATOR), COIL INSULATOR (BU-30) STOPPER (BU) HOLDER (BU30) GEAR (PULLEY) GEAR (CAM)
1-678-460-11 DRIVER BOARD
28
CDP-S3
7-4. BASE UNIT SECTION (BU-30BD60)
604 606
not supplied
605
#5 #5
not supplied
not supplied
603
602
601
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
Ref. No. 601 602 603 604
Part No. 3-531-576-11 A-4725-531-A 4-233-832-01 4-233-831-01
Description RIVET BD BOARD, COMPLETE GEAR (LB) GEAR (LA)
Remark
Ref. No. 605 0 606 #5
Part No.
Description
Remark
1-757-710-11 WIRE (FLAT TYPE) (16 CORE) A-4735-188-A BU-30 (60) ASSY 7-627-853-28 SCREW, PRECISION +P 2X3 TYPE3
29
CDP-S3 BD
NOTE: · Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. · -XX and -X mean standardized parts, so they may have some difference from the original one. · RESISTORS All resistors are in ohms. METAL: Metal-film resistor. METAL OXIDE: Metal oxide-film resistor. F: nonflammable
SECTION 8 ELECTRICAL PARTS LIST
· Items marked "*" are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. · SEMICONDUCTORS In each case, u: µ, for example: uA. . : µA. . uPA. . : µPA. . uPB. . : µPB. . uPC. . : µPC. . uPD. . : µPD. . · CAPACITORS uF: µF · COILS uH: µH The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. When indicating parts by reference number, please include the board.
Ref. No.
Part No.
Description
Remark
Ref. No. C191 C192 C193 C194 C195 C196 C197 C198
Part No. 1-124-584-00 1-163-038-11 1-104-665-11 1-163-038-11 1-163-038-11
Description ELECT CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP 100uF 0.1uF 100uF 0.1uF 0.1uF 0.1uF 0.1uF 100uF 20% 20%
Remark 10V 25V 10V 25V 25V 25V 16V 10V
A-4725-531-A BD BOARD, COMPLETE ******************* < CAPACITOR > C101 C102 C103 C104 C108 C109 C110 C111 C112 C114 C116 C117 C118 C121 C122 C123 C124 C125 C126 C127 C129 C130 C131 C133 C143 C145 C153 C159 C162 C165 C167 C168 C171 C172 C181 C182 C183 C184 C185 C190 1-162-967-11 1-107-826-11 1-162-962-11 1-162-962-11 1-107-826-11 1-162-965-11 1-162-967-11 1-162-927-11 1-109-982-11 1-163-038-11 1-104-665-11 1-104-665-11 1-162-964-11 1-163-038-11 1-124-584-00 1-162-970-11 1-107-823-11 1-163-038-11 1-163-038-11 1-124-584-00 1-162-974-11 1-163-038-11 1-104-665-11 1-162-921-11 1-163-038-11 1-163-038-11 1-163-038-11 1-162-970-11 1-104-665-11 1-163-038-11 1-162-919-11 1-162-921-11 1-115-412-11 1-162-927-11 1-115-412-11 1-162-927-11 1-162-968-11 1-162-968-11 1-107-823-11 1-115-156-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT ELECT CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.0033uF 0.1uF 470PF 470PF 0.1uF 0.0015uF 0.0033uF 100PF 1uF 0.1uF 100uF 100uF 0.001uF 0.1uF 100uF 0.01uF 0.47uF 0.1uF 0.1uF 100uF 0.01uF 0.1uF 100uF 33PF 0.1uF 0.1uF 0.1uF 0.01uF 100uF 0.1uF 22PF 33PF 680PF 100PF 680PF 100PF 0.0047uF 0.0047uF 0.47uF 1uF 10% 10% 10% 10% 10% 10% 10% 5% 10% 50V 16V 50V 50V 16V 50V 50V 50V 10V 25V 10V 10V 50V 25V 10V 25V 16V 25V 25V 10V 50V 25V 10V 50V 25V 25V 25V 25V 10V 25V 50V 50V 25V 50V 25V 50V 50V 50V 16V 10V
1-163-038-11 CERAMIC CHIP 1-107-826-11 CERAMIC CHIP 1-124-584-00 ELECT < CONNECTOR >
10% 20%
CN101 CN102
1-568-864-11 CONNECTOR, FFC 21P 1-793-907-11 CONNECTOR, FFC/FPC 16P < DIODE >
20% 20% 10% 20% 10% 10%
D101
8-719-422-12 DIODE UDZ-TE-17-3.9B < FERRITE BEAD >
FB101 FB102
1-500-445-21 FERRITE 1-500-445-21 FERRITE < IC >
0uH 0uH
20%
IC101 IC102 IC103
8-752-402-31 IC CXD3017Q 8-759-827-41 IC BA5974FM-E2 8-752-089-74 IC CXA2581N-T4 < SHORT >
20% 5%
10% 20%
JR101 JR102 JR103 JR104 JR105 JR106 JR122 JR123 JR124 JR125
1-216-295-11 1-216-295-11 1-216-295-11 1-216-295-11 1-216-295-11 1-216-295-11 1-216-296-11 1-216-296-11 1-216-296-11 1-216-296-11
SHORT SHORT SHORT SHORT SHORT SHORT SHORT SHORT SHORT SHORT < COIL >
0 0 0 0 0 0 0 0 0 0
5% 5% 5% 5% 5% 5% 10% 10% 10%
L101
1-469-553-21 INDUCTOR < TRANSISTOR >
4.7uH
Q101
8-729-010-08 TRANSISTOR
MSB710-RT1
30
CDP-S3 BD
Ref. No. Q102 Part No. Description 2SD1664-T100-QR 8-729-920-85 TRANSISTOR < RESISTOR > < PHOTO REFLECTOR > R101 R102 R103 R104 R105 R106 R107 R108 R109 R111 R114 R116 R117 R118 R119 R120 R122 R123 R124 R131 R143 R144 R147 R148 R149 R158 R159 R162 R171 R172 R173 R181 R182 R183 R190 R191 R192 R193 R194 R195 R196 R198 1-216-049-11 1-216-097-11 1-216-077-00 1-216-085-00 1-216-049-11 1-216-049-11 1-216-073-00 1-216-061-00 1-216-121-11 1-216-099-00 1-218-745-11 1-216-001-00 1-216-049-11 1-216-025-11 1-216-059-00 1-216-077-00 1-216-097-11 1-216-073-00 1-216-097-11 1-216-033-00 1-216-085-00 1-216-085-00 1-216-059-00 1-216-001-00 1-216-001-00 1-216-083-00 1-216-083-00 1-216-097-11 1-216-081-00 1-216-081-00 1-216-081-00 1-216-081-00 1-216-081-00 1-216-081-00 1-216-033-00 1-216-085-00 1-216-085-00 1-216-099-00 1-216-097-11 1-216-113-00 RES-CHIP RES-CHIP RES-CHIP METAL CHIP RES-CHIP RES-CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP RES-CHIP METAL CHIP RES-CHIP RES-CHIP METAL CHIP RES-CHIP RES-CHIP METAL CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP 1K 100K 15K 33K 1K 1K 10K 3.3K 1M 120K 160K 10 1K 100 2.7K 15K 100K 10K 100K 220 33K 33K 2.7K 10 10 27K 27K 100K 22K 22K 22K 22K 22K 22K 220 33K 33K 120K 100K 470K 2.2K 0 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/16W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W S741 1-771-821-11 SWITCH, PUSH (1 KEY) (IN) S742 1-771-821-11 SWITCH, PUSH (1 KEY) (OUT) ************************************************************** A-4725-658-A MAIN BOARD, COMPLETE ********************* 7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S RV101 1-238-602-11 RES, ADJ, CARBON 47K < CAPACITOR/RESISTOR > < VIBRATOR > X101 1-579-280-11 VIBRATOR, CRYSTAL (16.9344MHz) ************************************************************** C101 C102 C103 C116 C118 1-164-159-11 1-164-159-11 1-164-159-11 1-249-417-11 1-249-417-11 CERAMIC CERAMIC CERAMIC CARBON CARBON 0.1uF 0.1uF 0.1uF 1K 1K 50V 50V 50V 1/4W 1/4W IC751 8-749-924-30 PHOTO REFLECTOR GP2S28 (DISC IN DETECT) < RESISTOR > R751 1-249-407-11 CARBON 150 5% 1/4W ************************************************************** 1-678-460-11 DRIVER BOARD ************* < CAPACITOR > C701 C705 C706 C707 1-124-261-00 1-124-261-00 1-164-159-11 1-164-159-11 ELECT ELECT CERAMIC CERAMIC < CONNECTOR > CN701 CN702 CN703 CN704 CN705 1-785-324-11 1-785-328-11 1-785-331-11 1-785-329-11 1-785-329-21 PIN, CONNECTOR (STRAIGHT) 12P PIN, CONNECTOR (LIGHT ANGRE) 2P PIN, CONNECTOR (LIGHT ANGLE) 5P PIN, CONNECTOR (LIGHT ANGLE) 3P PIN, CONNECTOR (LIGHT ANGLE) 3P < IC > IC701 8-759-598-69 IC BA6956AN < TRANSISTOR > Q701 8-729-029-66 TRANSISTOR < RESISTOR > R701 1-249-429-11 CARBON 10K 5% 1/4W R702 1-249-401-11 CARBON 47 5% 1/4W R705 1-249-435-11 CARBON 33K 5% 1/4W R706 1-249-417-11 CARBON 1K 5% 1/4W R707 1-249-429-11 CARBON 10K 5% 1/4W ************************************************************** 1-678-462-11 IN OUT SW BOARD **************** < SWITCH > 1-216-057-00 METAL CHIP 1-216-295-11 SHORT RT1N141S-TP 10uF 10uF 0.1uF 0.1uF 20% 20% 50V 50V 50V 50V
DISC SENSOR
Remark Ref. No.
DRIVER
Part No.
IN OUT SW
MAIN
Remark
Description
1-678-463-11 DISC SENSOR BOARD ******************
< COMPOSITION CIRCUIT BLOCK > RN101 1-233-576-11 RES, CHIP NETWORK 100 < VARIABLE RESISTOR >
5% 5%
31
CDP-S3 MAIN
Ref. No. C122 C124 C125 C251 C255 C260 C261 C301 C302 C303 C304 C310 C311 C313 C314 C315 C316 C317 C318 C319 C320 C321 C401 C411 C416 C425 C427 C462 C463 C498 C499 C500 C501 C513 C521 C522 C523 C524 C531 C532 Part No. 1-161-494-00 1-164-159-11 1-126-923-11 1-161-494-00 1-161-494-00 1-161-494-00 1-161-494-00 1-126-959-11 1-162-600-11 1-162-306-11 1-161-494-00 1-161-494-00 1-162-306-11 1-162-286-31 1-162-282-31 1-162-282-31 1-162-282-31 1-162-282-31 1-162-282-31 1-162-282-31 1-162-306-11 1-161-494-00 1-161-494-00 1-126-960-11 1-126-964-11 1-162-282-31 1-162-282-31 1-161-494-00 1-126-964-11 1-161-494-00 1-161-494-00 1-164-159-11 1-126-937-11 1-126-935-11 1-164-159-11 1-126-935-11 1-126-934-11 1-126-934-11 1-164-159-11 1-126-935-11 Description CERAMIC CERAMIC ELECT CERAMIC CERAMIC CERAMIC CERAMIC ELECT CERAMIC CERAMIC CERAMIC CERAMIC CERAMIC CERAMIC CERAMIC CERAMIC CERAMIC CERAMIC CERAMIC CERAMIC CERAMIC CERAMIC CERAMIC ELECT ELECT CERAMIC CERAMIC CERAMIC ELECT CERAMIC CERAMIC CERAMIC ELECT ELECT CERAMIC ELECT ELECT ELECT CERAMIC ELECT < CONNECTOR > * CN101 CN102 CN103 CN301 * CN401 1-568-419-11 PIN, CONNECTOR 9P 1-568-373-11 PIN, CONNECTOR 8P 1-566-859-11 SOCKET, CONNECTOR 15P (SYSTEM CONTROL 5 TO TC-S3) 1-568-838-11 CONNECTOR, FFC 21P 1-568-936-11 PIN, CONNECTOR 9P < DIODE > D105 D123 D501 D502 D503 D504 D511 D512 8-719-911-19 8-719-982-96 8-719-024-99 8-719-024-99 8-719-024-99 DIODE DIODE DIODE DIODE DIODE 1SS133T-72 MTZJ-T-72-2.2A 11ES2-NTA2B 11ES2-NTA2B 11ES2-NTA2B 0.022uF 0.1uF 220uF 0.022uF 0.022uF Remark 25V 50V 10V 25V 25V 25V 25V 50V 16V 16V 25V 25V 16V 50V 50V 50V 50V 50V 50V 50V 16V 25V 25V 50V 50V 50V 50V 25V 50V 25V 25V 50V 16V 10V 50V 10V 10V 10V 50V 10V Ref. No. D513 D514 D515 Part No. Description Remark 8-719-024-99 DIODE 11ES2-NTA2B 8-719-024-99 DIODE 11ES2-NTA2B 8-719-024-99 DIODE 11ES2-NTA2B < FERRITE BEAD > FB305 FB310 FB311 FB312 FB313 FB314 FB315 FB410 FB416 1-412-473-21 1-412-473-21 1-412-473-21 1-412-473-21 1-412-473-21 1-412-473-21 1-412-473-21 1-412-473-21 1-412-473-21 INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR < IC > 100PF 100PF 100PF 100PF 100PF 0.01uF 0.022uF 0.022uF 1uF 10uF 100PF 100PF 0.022uF 10uF 0.022uF 0.022uF 0.1uF 4700uF 470uF 0.1uF 470uF 220uF 220uF 0.1uF 470uF 10% 10% 10% 10% 10% 20% IC102 IC401 IC402 IC502 IC503 8-749-019-13 8-759-827-46 8-759-269-09 8-759-158-62 8-759-071-48 IC IC IC IC IC TOTX140 (OPTICAL OUT TO ST-S3/S5) M30620MAA-B31FP SN74HCT04ANS-E05 TA78057S TA7807S 0uH 0uH 0uH 0uH 0uH 0uH 0uH 0uH 0uH
20%
0.022uF 0.022uF 0.47uF 20% 0.0047uF 20% 0.01uF 20% 0.022uF 0.022uF 0.01uF 220PF 100PF
20% 10% 10%
< RESISTOR > JW98 JW99 1-247-807-31 CARBON 1-247-807-31 CARBON < COIL > L125 L310 1-410-336-11 INDUCTOR 1-410-467-11 INDUCTOR < TRANSISTOR > Q501 Q502 8-729-049-79 TRANSISTOR 8-729-900-80 TRANSISTOR < RESISTOR > R123 R132 R133 R134 R401 R402 R403 R409 R411 R412 R413 R417 R419 R424 R425 R426 R427 R428 R429 R430 R432 R433 1-247-807-31 1-247-876-11 1-247-876-11 1-249-417-11 1-247-807-31 1-247-807-31 1-247-807-31 1-249-429-11 1-247-807-31 1-249-429-11 1-249-411-11 1-249-429-11 1-247-807-31 1-249-421-11 1-249-425-11 1-247-887-00 1-249-425-11 1-249-441-11 1-247-807-31 1-247-807-31 CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON 100 75K 75K 1K 100 100 100 10K 100 10K 330 10K 100 2.2K 4.7K 220K 4.7K 100K 100 100 100 100 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W RT1P137S-TP BA1A4M-TP 220uH 5.6uH 100 100 5% 5% 1/4W 1/4W
20% 20% 10% 10% 20%
20% 20%
20% 20% 20% 20%
8-719-024-99 DIODE 11ES2-NTA2B 8-719-024-99 DIODE 11ES2-NTA2B 8-719-024-99 DIODE 11ES2-NTA2B
1-247-807-31 CARBON 1-247-807-31 CARBON
32
CDP-S3 MAIN
Ref. No. R435 R436 R437 R438 R440 R441 R442 R443 R444 R445 R446 R447 R448 R449 R450 R451 R452 R453 R456 R457 R459 R460 R465 R469 R473 R477 R480 R481 R482 R483 R484 R485 R486 R487 R489 R490 R491 R492 R493 R494 R495 R496 R497 R500 Part No. Description 100 100 100 100 100 10K 100 100 100 100 100 100 100 100 100 100 100 100 10K 10K 100 10K 150 150 150 150 100K 150 10K 10K 100 100 100 100 100 100 100 4.7K 150 100 100 10K 100 10K 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 1-247-807-31 CARBON 1-247-807-31 CARBON 1-247-807-31 CARBON 1-247-807-31 1-247-807-31 1-249-429-11 1-247-807-31 1-247-807-31 1-247-807-31 1-247-807-31 1-247-807-31 1-247-807-31 1-247-807-31 1-247-807-31 1-247-807-31 1-247-807-31 1-247-807-31 1-247-807-31 1-249-429-11 1-249-429-11 1-247-807-31 1-249-429-11 1-249-407-11 1-249-407-11 1-249-407-11 1-249-407-11 1-249-441-11 1-249-407-11 1-249-429-11 1-249-429-11 1-247-807-31 1-247-807-31 1-247-807-31 1-247-807-31 1-247-807-31 1-247-807-31 1-247-807-31 1-249-425-11 1-249-407-11 1-247-807-31 1-247-807-31 1-249-429-11 1-247-807-31 CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON
MOTOR
1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W
PANEL (L)
Ref. No.
PANEL (R)
Description
TRAY SENSOR
Remark
Remark
Part No.
1-680-995-11 PANEL (L) BOARD *************** < LED > D701 D702 D703 D704 D705 8-719-057-97 8-719-058-03 8-719-057-97 8-719-057-97 8-719-057-97 LED LED LED LED LED SEL5923A-TP15 (X) SEL5423E-TP15 (N) SEL5923A-TP15 (3) SEL5923A-TP15 (2) SEL5923A-TP15 (1)
< RESISTOR > R710 R711 R712 R713 R714 R715 R716 1-249-410-11 1-249-411-11 1-249-413-11 1-249-414-11 1-249-415-11 CARBON CARBON CARBON CARBON CARBON 270 330 470 560 680 1K 1.2K 5% 5% 5% 5% 5% 5% 5% 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W
1-249-417-11 CARBON 1-249-418-11 CARBON < SWITCH >
S711 S712 S713 S714 S715
1-771-410-21 1-771-410-21 1-771-410-21 1-771-410-21 1-771-410-21
SWITCH, TACTILE (m) SWITCH, TACTILE (M) SWITCH, TACTILE (>) SWITCH, TACTILE (.) SWITCH, TACTILE (x)
S716 1-771-410-21 SWITCH, TACTILE (X) S717 1-771-410-21 SWITCH, TACTILE (N) ************************************************************** 1-680-996-11 PANEL (R) BOARD *************** < RESISTOR > R700 R701 R702 R703 R704 R705 R706 R707 1-249-410-11 1-249-411-11 1-249-413-11 1-249-414-11 1-249-415-11 CARBON CARBON CARBON CARBON CARBON 270 330 470 560 680 1K 1.2K 1.8K 5% 5% 5% 5% 5% 5% 5% 5% 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W
1-249-417-11 CARBON 1-249-418-11 CARBON 1-249-420-11 CARBON < SWITCH >
1-249-429-11 CARBON < VIBRATOR >
S701 S702 S703 S704 S705
1-771-410-21 1-771-410-21 1-771-410-21 1-771-410-21 1-771-410-21
SWITCH, TACTILE (DISC 3) SWITCH, TACTILE (DISC 2) SWITCH, TACTILE (DISC1) SWITCH, TACTILE (Z (DISC 1)) SWITCH, TACTILE (Z (DISC 2))
X401 1-781-107-21 VIBRATOR, CERAMIC (16MHz) ************************************************************** 1-678-461-11 MOTOR BOARD ************* < CAPACITOR > C721 1-162-306-11 CERAMIC 0.01uF 30% 16V **************************************************************
S706 1-771-410-21 SWITCH, TACTILE (Z (DISC 3)) S707 1-771-410-21 SWITCH, TACTILE (REPEAT) S708 1-771-410-21 SWITCH, TACTILE (PLAY MODE) ************************************************************** 1-678-457-11 TRAY SENSOR BOARD ****************** < CAPACITOR > C731 1-164-159-11 CERAMIC 0.1uF 50V
33
CDP-S3
Ver 1.1
TRAY SENSOR
Ref. No. Part No. Description < PHOTO SENSOR > IC731 IC732 IC733 8-749-016-76 PHOTO SENSOR RPI-321 8-749-016-76 PHOTO SENSOR RPI-321 8-749-016-76 PHOTO SENSOR RPI-321 < RESISTOR > R731 R732 R733 R734 R735 1-247-876-11 1-249-408-11 1-247-876-11 1-249-408-11 1-247-876-11 CARBON CARBON CARBON CARBON CARBON 75K 180 75K 180 75K 5% 5% 5% 5% 5% 1/4W 1/4W 1/4W 1/4W 1/4W Remark Ref. No. Part No. Description Remark
R736 1-249-408-11 CARBON 180 5% 1/4W *********************************************************** MISCELLANEOUS ************** 9 11 571 605 0 606 M721 1-823-055-11 1-757-633-11 X-4952-971-2 1-757-710-11 A-4735-188-A WIRE (FLAT TYPE) (21 CORE) CORD (WITH CONNECTOR) 17P MOTOR ASSY WIRE (FLAT TYPE) (16 CORE) BU-30 (60) ASSY
1-541-632-12 MOTOR, DC (LOADING)
34
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
CDP-S3
MEMO
35
CDP-S3
REVISION HISTORY
Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. 1.0 1.1 1.2 1.3 Date 2001.04 2002.09 2002.11 2002.12 Description of Revision New Change of Part No. for IC731, 732, 733 on TRAY SENSOR board
(ECN-CDB04887)
Addition of Ref. No. 521, 522, 523, 524 to EXPLODED VIEWS
(SPM-02098)
Addition of Ref. No. 525 to EXPLODED VIEWS
(SPM-02116)