Text preview for : Tda4820t.pdf part of Philips TDA4820t Philips Quality Data Sheet
Back to : Tda4820t.pdf | Home
INTEGRATED CIRCUITS
DATA SHEET
TDA4820T Sync separation circuit for video applications
Preliminary specification File under Integrated Circuits, IC02 June 1990
Philips Semiconductors
Preliminary specification
Sync separation circuit for video applications
FEATURES · Fully integrated, few external components · Positive video input signal, capacitively coupled · Operates with non-standard video input signals · Black level clamping · Generation of composite sync slicing level at 50% of peak sync voltage · Vertical sync separator with double slope integrator · Delay time of the vertical output pulse is determined by an external resistor · Vertical sync generation with a slicing level at 40% of peak sync voltage · Output stage for composite sync · Output stage for vertical sync GENERAL DESCRIPTION
TDA4820T
The TDA4820T is a monolithic integrated circuit including a horizontal and a vertical sync separator, offering composite sync and vertical sync extracted from the video signal.
QUICK REFERENCE DATA SYMBOL VP IP V2(p-p) Vsync(p-p) Vo Vo Vo Tamb PARAMETER supply voltage range (pin 1) supply current (pin 1) input voltage amplitude (peak-to-peak value) sync pulse input voltage amplitude (pin 2) (peak-to-peak value) maximum vertical sync output voltage (pin 6) maximum composite sync output voltage (pin 7) minimum output voltage (pins 6 and 7) operating ambient temperature range I6 = -1 mA I7 = -3 mA I6,7 = 1 mA CONDITIONS - 0.2 50 10.0 10.0 - 0 MIN. 10.8 8 1 300 - - - - TYP. 12 MAX. 13.2 12 3 500 - - 0.6 + 70 UNIT V mA V mV V V V °C
ORDERING AND PACKAGE INFORMATION EXTENDED TYPE NUMBER TDA4820T Note 1. SOT96-1; 1997 January 08. PACKAGE PINS 8 PIN POSITION mini-pack MATERIAL plastic CODE SO8; SOT96A (1)
June 1990
2
Philips Semiconductors
Preliminary specification
Sync separation circuit for video applications
TDA4820T
Fig.1 Block diagram and application circuit.
PINNING SYMBOL VP VCVBS SLEV VDEL n.c. VSYN CSYN GND PIN 1 2 3 4 5 6 7 8 DESCRIPTION supply voltage video input signal slicing level vertical integration delay time not connected vertical sync output signal composite sync output signal ground
PIN CONFIGURATION
Fig.2 Pin configuration.
June 1990
3
Philips Semiconductors
Preliminary specification
Sync separation circuit for video applications
FUNCTIONAL DESCRIPTION The complete circuit consists of the following functional blocks as shown in Fig.1: Video amplifier and black level clamping 50% peak sync voltage Composite sync slicing Vertical slicing and double slope integrator Vertical sync output Composite sync output Video amplifier and black level clamping (pin 2) The sync separation circuit TDA4820T is designed for positive video input signals. The video signal (supplied via capacitor C2 at pin 2) is amplified by approximately 15 in the input amplifier. The black level clamping voltage (approximately 2 V) is stored by capacitor C2. 50% peak sync voltage (pin 3) From the black level and the peak sync voltage, the 50% value of the peak sync voltage is generated and stored by capacitor C3 at pin 3. A slicing level control circuit ensures a constant 50% value, as long as the sync pulse amplitude at pin 2 is between 50 mV and 500 mV, independent of the amplitude of the picture content. Composite sync slicing
TDA4820T
A comparator in the composite sync slicing stage compares the amplified video signal with the DC voltage derived from 50% peak sync voltage. This generates the composite sync output signal. Vertical slicing and double slope integrator Vertical slicing compares the composite sync signal with a DC level equal to 40 % of the peak sync voltage, similar to the composite sync slicing. With signal interference (reflections or noise) the reduced vertical slicing level ensures more energy for the vertical pulse integration. The slope is double-integrated to eliminate the influence of signal interference. The vertical integration delay time tdV can be set from typically 45 µs (pin 4 open) to typically 18 µs (pin 4 grounded). Between these maximum and minimum values, tdV can be set by a resistor R1 from pin 4 to ground. For optimum sync behaviour with input line sync pulses only, R1 has to be 3.3 k. In this case tdV is typically 23 µs. Vertical sync output Composite sync output Both output stages are emitter followers with bias currents of 2 mA.
Fig.3 Internal circuits.
June 1990
4
Philips Semiconductors
Preliminary specification
Sync separation circuit for video applications
LIMITING VALUES In accordance with the Absolute Maximum System (IEC 134) SYMBOL VP Vi Io Tstg Tamb Tj Ptot supply voltage (pin 1) input voltage (pin 2) output current (pin 6 and pin 7) storage temperature range operating ambient temperature range maximum junction temperature total power dissipation PARAMETER 0 -0.5 3 -25 0 - - MIN. 6 -10 + 150 + 70 150 500
TDA4820T
MAX. 13.2 V V
UNIT
mA °C °C °C mW
June 1990
5
Philips Semiconductors
Preliminary specification
Sync separation circuit for video applications
CHARACTERISTICS All voltages measured to GND (pin 8); VP = 12 V; Tamb = 25 °C; unless otherwise specified. SYMBOL VP IP PARAMETER supply voltage range (pin 1) supply current (pin 1) CONDITIONS MIN. 10.8 4 8 TYP. 12.0
TDA4820T
MAX. 13.2 12 V
UNIT mA
Video amplifier V2(p-p) Vsync (p-p) input amplitude (peak-to-peak value) sync pulse amplitude (pin 2) (peak-to-peak value) source impedance positive video signal AC coupled composite sync slicing level 50% for 0.2 V V2(p-p) 1.5 V 0.2 50 1 300 3 500 V mV
Zs I2
- - - - - - - during vertical sync during sync pulse 0.2 V V2(p-p) 1.5 V maximum load at pin 7: CL 5 pF; RL 100 k 0.2 V V2(p-p) 1.5 V pin 4 open pin 4 grounded I6 = -1 mA I7 = -3 mA I6,7 = 1 mA pin 4 open; standard signal of 625 lines - - - -
-
200 - - - - - - - - - 500
µA µA µA µA µA µA µA µA
Black level clamping discharge current of C2 charge currents of C2 during video content sync below slicing level sync above slicing level during black level 50% peak sync voltage I3 discharge current of C3 maximum charge current of C3 reduced charge current of C3 charge current of C3 Composite sync slicing (see Fig.4) composite sync slicing level tdH horizontal delay time (pin 7) 50 250 % ns during video content 16 -345 -255 -160 5 -40 -25 -20
Vertical sync separation (see Fig.5) slicing level for vertical sync tdV vertical leading edge delay times (pin 6) - 30 11 40 45 18 - 60 25 % µs µs
Vertical and composite sync outputs Vo Vo Vo tW maximum vertical sync output voltage (pin 6) maximum composite sync output voltage (pin 7) minimum output voltages (pins 6 and 7) vertical sync pulse width 10.0 10.0 0.1 - 10.5 10.5 0.3 180 11.5 11.5 0.6 - V V V µs
June 1990
6
Philips Semiconductors
Preliminary specification
Sync separation circuit for video applications
TDA4820T
Fig.4 Typical horizontal sync signal.
(1) due to 625 line standard
Fig.5 Typical vertical signal
June 1990
7
Philips Semiconductors
Preliminary specification
Sync separation circuit for video applications
PACKAGE OUTLINE SO8: plastic small outline package; 8 leads; body width 3.9 mm
TDA4820T
SOT96-1
D
E
A X
c y HE v M A
Z 8 5
Q A2 A1 pin 1 index Lp 1 e bp 4 w M L detail X (A 3) A
0
2.5 scale
5 mm
DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT mm inches A max. 1.75 A1 0.25 0.10 A2 1.45 1.25 A3 0.25 0.01 bp 0.49 0.36 c 0.25 0.19 D (1) 5.0 4.8 0.20 0.19 E (2) 4.0 3.8 0.16 0.15 e 1.27 0.050 HE 6.2 5.8 0.24 0.23 L 1.05 Lp 1.0 0.4 Q 0.7 0.6 v 0.25 0.01 w 0.25 0.01 y 0.1 Z (1) 0.7 0.3
0.0098 0.057 0.069 0.0039 0.049
0.019 0.0098 0.014 0.0075
0.039 0.028 0.041 0.016 0.024
0.028 0.004 0.012
8 0o
o
Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic or metal protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT96-1 REFERENCES IEC 076E03S JEDEC MS-012AA EIAJ EUROPEAN PROJECTION
ISSUE DATE 92-11-17 95-02-04
June 1990
8
Philips Semiconductors
Preliminary specification
Sync separation circuit for video applications
SOLDERING Introduction There is no soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and surface mounted components are mixed on one printed-circuit board. However, wave soldering is not always suitable for surface mounted ICs, or for printed-circuits with high population densities. In these situations reflow soldering is often used. This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our "IC Package Databook" (order code 9398 652 90011). Reflow soldering Reflow soldering techniques are suitable for all SO packages. Reflow soldering requires solder paste (a suspension of fine solder particles, flux and binding agent) to be applied to the printed-circuit board by screen printing, stencilling or pressure-syringe dispensing before package placement. Several techniques exist for reflowing; for example, thermal conduction by heated belt. Dwell times vary between 50 and 300 seconds depending on heating method. Typical reflow temperatures range from 215 to 250 °C. Preheating is necessary to dry the paste and evaporate the binding agent. Preheating duration: 45 minutes at 45 °C. Wave soldering
TDA4820T
Wave soldering techniques can be used for all SO packages if the following conditions are observed: · A double-wave (a turbulent wave with high upward pressure followed by a smooth laminar wave) soldering technique should be used. · The longitudinal axis of the package footprint must be parallel to the solder flow. · The package footprint must incorporate solder thieves at the downstream end. During placement and before soldering, the package must be fixed with a droplet of adhesive. The adhesive can be applied by screen printing, pin transfer or syringe dispensing. The package can be soldered after the adhesive is cured. Maximum permissible solder temperature is 260 °C, and maximum duration of package immersion in solder is 10 seconds, if cooled to less than 150 °C within 6 seconds. Typical dwell time is 4 seconds at 250 °C. A mildly-activated flux will eliminate the need for removal of corrosive residues in most applications. Repairing soldered joints Fix the component by first soldering two diagonallyopposite end leads. Use only a low voltage soldering iron (less than 24 V) applied to the flat part of the lead. Contact time must be limited to 10 seconds at up to 300 °C. When using a dedicated tool, all other leads can be soldered in one operation within 2 to 5 seconds between 270 and 320 °C.
June 1990
9
Philips Semiconductors
Preliminary specification
Sync separation circuit for video applications
DEFINITIONS Data sheet status Objective specification Preliminary specification Product specification Limiting values
TDA4820T
This data sheet contains target or goal specifications for product development. This data sheet contains preliminary data; supplementary data may be published later. This data sheet contains final product specifications.
Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Where application information is given, it is advisory and does not form part of the specification. LIFE SUPPORT APPLICATIONS These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale.
June 1990
10