Make | Model | Problem | Solution | Date |
| | | |
Found: 66
|
Alba | CTV4851 11AK19B-1 | Dead with 0nly 300v pri HT | Opto coupler faulty - though more faults may be present (esp if it went off in a thunderstorm) | 14-09-04 |
Bush | 11AK19-B1 | Field collapse | After trying new chip TDA8351 which made no diff, fault traced to D606 BA157 which checked ok out of cct | 14-09-04 |
Daewoo | CP420 GB14F7T1 | Int reverts to st/by | RLY2 relay was operating when fault occurred - IC I807 (TOP210-PF1) the standby switch mode IC in the power supply | 14-09-04 |
Daewoo | GB14F7T1 | Dead - psu ok but no lop | hairline crack by LOPTr coll tp LOPTx | 14-09-04 |
Daewoo | GB14F7T1 | Sound disappears int | (IC) I501 a TDA8374A mounted on the VCR pcb. | 14-09-04 |
Daewoo | GB14F7T1 | Won't sw on with tape stuck - st/by only | No volts at 6v reg IC1806 - P803 plug/skt has 8v in but no 8v o/p due to dry joint on/off sw | 14-09-04 |
Daewoo | GB14F7T1 CP420 | St/by only | R804 47k start up res | 14-09-04 |
Daewoo | GB14F8T1 | No Vol adj - osg stuck ? way | IC1703 24C08P eeprom - pre-prog by Daewoo from SEME @ ?18 | 14-09-04 |
Daewoo | GB14H1N | No tuning - supply & clk/data lines ok | Tuner faulty - replaced Type DT5-BF18D pt no 48597-19930 | 14-09-04 |
Daewoo | GB14H1N | Service mode entering | Press "Norm-av-sleep-clear-stby" on R/C | 14-09-04 |
|
Daewoo | GB14H1N | Sound absent & snowy pic aft re-assemby | Check pl/skt conns of spk - can be accidentally put in set AGC skt | 14-09-04 |
Daewoo | GB14H1N | Won't come out of st/by, sw off when playing, OSG corrugated - all int | I826 3.3v reg LE33CZ on front of pcb - available From Farnell | 14-09-04 |
Daewoo | GB14H1T | Service mode entering | On hset press Blue > Yellow > Green > Red > Stby sequencially. When brought out of st/by should be in service mode. Use buttons 1 & 4 for Slope Adjust; 2 & 5 for Vert Centre; Use buttons 3 & 6 for Vert Amp... | 14-09-04 |
Daewoo | GB14H1T | Sync absent | eeprom - [clock & data lines on video ic were low by approx 1v] | 14-09-04 |
Ferguson | B14R | St/by only | DP36 BA157 s/c | 14-09-04 |
FERGUSON | B14R (TX80) | DEAD AND WHISTLING | CHECK RP68 | 14-09-04 |
Ferguson | B14R (TX80) | DEAD AND WHISTLING | CHECK RP68 | 14-09-04 |
FERGUSON | B14R/TX80 | INTERMITTANT FLYBACK LINES | REPLACE DF04 BA157 | 14-09-04 |
Ferguson | F14VB12A | Sound int lost | IS001 switching chip 101-22-010 | 14-09-04 |
Ferguson | TX80 B14R | Dead, whistling | RP68 0R68 o/c - in 13v feed | 14-09-04 |
Ferguson | TX80 B14R | Humbar at LH side of screen & TP10 LOPTr overheating. | DP 30 DP15 DP16 IN4001 diodes, one or all open circuit | 14-09-04 |
Ferguson | TX80 B14R | Int Fback lines | DF04 BA517 | 14-09-04 |
Ferguson | TX90 B14C | Slow (10 mins) for pic & sound to appear | Dry joints Field cct | 14-09-04 |
Ferguson | TX91 Thomson 10MH73B 10MG73B | dead | SMD TF21 near LOPTx not soldered in factory | 14-09-04 |
Ferguson | TX91 Thomson 10MH73B 10MG73B | dead on 12V supply (car supply) | RD09, RD19 22R 0.5W fusible | 14-09-04 |
Goldstar | CB14A80E | Reduced width. 6-8 volts on supply pin of TDA8362 | Replace TDA8362. Supplying +12V to supply pin of TDA8362, restored width but with no hor. Synchronization. | 14-09-04 |
Goldstar | CB14A80E | Reduced width. 6-8 volts on supply pin of TDA8362 | Replace TDA8362. Supplying +12V to supply pin of TDA8362, restored width but with no hor. Synchronization. | 14-09-04 |
Goldstar | CB14A80E | Relay goes on, then off, immediately after switch on | Change memory chip St24C02C. | 14-09-04 |
Goodmans | GTV66W1 11AK19B-1 | Width reduced & no E-W | C630, R629 2R7 and the BUK444 200A. | 14-09-04 |
ITT | Compact B 110 | Poor sync/sound mute | 4µ7 in if can | 14-09-04 |