Make | Model | Problem | Solution | Date |
| | | |
Found: 107
|
Finlux | 3021F | INT LOSS SIGNALS | DU21 INT OC 7v RECTIFIER | 14-09-04 |
Finlux | 3021F | No frame. | SDA2526 memory IC on control PCB beneath tube. | 14-09-04 |
Finlux | 3021F | PICTURE TOO WIDE NO EW | CH29 0.1uF OC ON SIGNALS PCB | 14-09-04 |
Finlux | 3021F | Varying col intensity | Hum bar on 12v line - Ra34 47R | 14-09-04 |
Finlux | 3021F | Width excess/E-W faulty | CH29 0µ1 o/c in sigs pcb | 14-09-04 |
Finlux | 3024 | BLACK BANDS ON SCREEN WORSE AT TOP | CK8 0.1uF ( UNDER FIELD HEATSINK ) | 14-09-04 |
Finlux | 3024 | Int sync | Ra13 & Ra17 on sigs/IF panel never been soldered | 14-09-04 |
Finlux | 3024 | There was intermittent loss of line and field sync | One end of both Ra13 and Ra17 had never been soldered. | 14-09-04 |
Finlux | 3024F | LINE TRANSISTOR SC REPLACEMENT BLOWS AFTER 2-3hrs | Tz3 LINE DRIVER US + DRY JOINTS | 14-09-04 |
Finlux | 3024F | No pic - faint vert line down centre at sw off | C219 scan coupling cap 470nf 250v split | 14-09-04 |
|
Finlux | 3024F | No signals received - ok on scart | ICi1 SDA3203-3 | 14-09-04 |
Finlux | 3029 3000 | Line spacing at bottom of screen. | CK8 ( .1uf , 63V ) small white square under frame o/p IC heatsink. | 14-09-04 |
Finlux | 3029V | DARK BARS ON PICTURE AND OR FIELD CRAMPING PIN 3 L | Cz14 4u7 250v OC | 14-09-04 |
Finlux | 3029V 3000 | Dark bars across top of picture plus cramping | Ck8 ( 0.1uf ) o/c , Cz14 ( 4.7uf , 250v ) . | 14-09-04 |
Finlux | 3621 | PATTERNING AT LOW BRIGHTNESS LEVELS OF PICTURE | CG46 470uF 16v | 14-09-04 |
Finlux | 3621 | White patterning on dark scenes | Noise on 7v rail - CG46 470µ 16v | 14-09-04 |
Finlux | 3621F | NO PICTURE OR SOUND RASTER OK | TDA2450-2 ICi2 US CHECK 11v ON PIN 3 | 14-09-04 |
Finlux | 3621F | No sound/pic "P100" appears in txt mode | ICi2 if chip TDA2450-2 | 14-09-04 |
Finlux | 5000 | Chopper tr BUZ91 Tu1fails aft 10 ins | Check Du7 BYV36C diode in snubber network | 14-09-04 |
Finlux | 5000 | Dead , BUZ91 chopper transistor Tu1 s.c , both fuse | Should have 1.2 -2.5V at pin 2. If OV , replace Ru24 and Ru26 ( both 150k ) . Should be 1.8V at pin 3. If high , replace Ru22 and | 14-09-04 |
Finlux | 5000 | Dead BUZ91 chopper tr s/c & 3 fuses o/c | Check Du1 BY500, Ru24/26 150k, Ru22/23 374k | 14-09-04 |
Finlux | 5000 | Dead with noises | Cu34 220µ 385v mains cap o/c | 14-09-04 |
Finlux | 5000 | Int goes pink with fb lines | JE38 link dry jointed (part covered by front plastic) | 14-09-04 |
Finlux | 5000 | No luminance - sound/text ok | Te9 BC857 - not marked on pcb - base to pin 9 txt pcb, 1k emitter res Ra88 to junct Re31 & Re35 | 14-09-04 |
Finlux | 5000 | No signals | Tuner supply pin 3 stuck at 30v (0-24v); ICa2 EEPROM faulty | 14-09-04 |
Finlux | 5000 | Wont come on from st/by (ok from front) | Du4 BYS27-45 7v supply rect | 14-09-04 |
Finlux | 5025 | No sound/dist sound | ICp1 TDA1521, Ra73 0R1 in 30v supply risen in value | 14-09-04 |
Finlux | 5025 | Sync slow to lock on chan change | resolder all joints on IF board and in the jungle chip area | 14-09-04 |
Finlux | 5025C26 | No or dist sound via Scart | RL74 0R68 fusible o/c in series with 12v supply | 14-09-04 |
Finlux | 5025S | Int loss of pic | crt htrs int - bad joints R929 on crt base & Rz2 & 5 on main pcb & ribbon cable conns between main pcb & crt | 14-09-04 |