| Make | Model | Problem | Solution | Date |
| | | |
| Found: 24
|
| Schneider | 1500 | Dead. | T860. | 14-09-04 |
| Schneider | 26" | Starts but it is not possible to change programs or to search for channels. | Change Control chip SDA2030-A002 | 14-09-04 |
| Schneider | 26" | Won't start, PS protection active. | Desolder Vertical IC, if it starts, change it. | 14-09-04 |
| Schneider | 26" (It can also be found as Koerting model 26) | Starts but it is not possible to change programs or to search for channels. | Change Control chip SDA2030-A002 | 14-09-04 |
| Schneider | 26" (It can also be found as Koerting model 26) | Won't start, PS protection active. | Desolder Vertical IC, if it starts, change it. | 14-09-04 |
| Schneider | 2804T | Dead - fuse s601 blown | Been uprated from 2.5A to 3.15A ceramic | 14-09-04 |
| Schneider | 2818UK | No pic - sound present | R326 o/c - replacing & advancing A1s gives rainbow effect on screen - FOP chip | 14-09-04 |
| Schneider | 9.1 | Dead - LOPTr s/c | LOPTr S2055N and LOPTx 1352.5033 (Eldor). | 14-09-04 |
| Schneider | 9.6 | Dead - LOPTr s/c | When replaced went same way - cause LOPTx | 14-09-04 |
| Schneider | CTV2802 | Arcing LOPTx | Loptx replaced pt no HR8320 - will fit with some slight mod to clips etc | 14-09-04 |
|
|
| Schneider | DTV3 | Service Mode access | Press & release "red" & "blue" button on R/C. Simultaneously press within 5 secs "PROGRAM -" &
"Volume +" on TV. | 14-09-04 |
| Schneider | Euro70222 | Dead | Line dr tr s/c & R306 burnt | 14-09-04 |
| Schneider | F10 | LED blinking 3 times & no power | BU808DFI (HOT)blown, replacement restored pic but shifted to right - C125 4µ7 faulty | 14-09-04 |
| Schneider | Scinema 2817 | Dead | FOP chip & LOPTx | 14-09-04 |
| Schneider | STV 171 | repeatedly S/C of BU508 AF | line drive Q508(2SC1573) int S/C, replace with BF759. Change R 608 (1Kohm) to 2K2 /2 W | 14-09-04 |
| Schneider | STV1401 11AK20D2 | Faint tripping noise only | D811 (MR852) the 16volt line rectifier diode was S/C. Fitted a BYT13 (1000v 3amp). | 14-09-04 |
| Schneider | STV1401 11AK20M | Dead - LOPTr Q602 BU808DF1 s/c | C602 22µ base coupling cap low cap | 14-09-04 |
| Schneider | STV2801T TV9.1 | Dead with LOPTr S2055AF s/c | lopt HR8320 (18.44UKP +vat From Seme) - reqs heatsink to be cut to fit in | 14-09-04 |
| Schneider | STV2802 TV9.1 | Service mode entering | Press red & blue buttons on RC together. Press prog down & vol up on TV together within 5 secs. Select items using up/down buttons. Parameters use red button. Adjust value using volume +/-. Press OK button to store value. Leave service mode by pressing TV button. | 14-09-04 |
| Schneider | STV2802T | Dead - mains fuse blown | Mains bridge rect s/c (looks under rated) | 14-09-04 |
| Schneider | STV2802T | Dead - mains fuse shattered - bridge rect s/c | Replacing faulty items caused a repeat of the fault - caused by faulty mains smoothing cap | 14-09-04 |
| Schneider | STV5187CH 11AK19-48 | Dead with LED lit Green | No line drive - TDA8840-1Y (can use 2Y suffix but will need to adj brill) | 14-09-04 |
| Schneider | STV5501 11AK19 | Bright screen with fb lines | Check D609 BA159 & its series connected resistor | 14-09-04 |
| Schneider | TV17022M | No E-W after LOPTx & LOPTr replacement | Q305 sm | 14-09-04 |