Panasonic KX-TC1035BXW free download

File name KX-TC1035BXW.pdf

ORDER NO. KM40012753C3 Telephone Equipment KX-TC1035BXW Cordless Phone White Version (for Asia, Middle Near East and Other areas) 1 2005-05-13 SPECIFICATIONS 1 2 2005-05-13 1. STANDARD BATTERY LIFE If your Panasonic battery is fully charged; While in use (TALK) While not in use (Stand-by) Up to about 6 hours Up to about 30 days - Battery life may vary depending on usage conditions and ambient temperature. - Clean the handset and the base unit charge contacts with a soft, dry cloth. Clean if the unit is subject to grease, dust or high humidity. Otherwise the battery may not charge propery. - If the battery is fully charged, you do not have to place the handset on the base unit until the RECHARGE indicator flashes. This will maximize the battery life. - The battery cannot be overcharged. 2. LOCATION OF CONTROLS 3 2005-05-13 4 2005-05-13 3. CONNECTION 1. Connect as shown. 5 2005-05-13 - USE ONLY WITH Panasonic ACADAPTOR PQLV1BXZ. - The AC adaptor must remain connected at all times. (It is normal for the adaptor to feel warm during use.) - When more than one unit is used, the units may interfere with each other. To prevent or reduce interference, please leave ample space between the base units. 6 2005-05-13 3.1. Adding Another Phone This unit will not function during a power failue. To connect a standard telephone on the same line, use a T-adaptor. 4. DISASSEMBLY INSTRUCUTIONS 7 2005-05-13 Ref. No. Procedure Shown in Fig -. 1 2 3 4 5 6 1 1, 2 1, 2, 3 4 4, 5 4-6 1 2 3 4 5 6 To remove -. Lower Cabinet Main Printed Circuit Board Charge Terminal Rear Cabinet Main Printed Circuit Board Remove -. Screws (3 Ч 14)... (A) Ч 5 Screws (3 Ч 14)... (B) Ч 1 Screws (3 Ч 10)... (C) Ч 2 Remove the battery compartment cover Screws (2.6 Ч 14)...(E) Ч 2 Screws (2.6 Ч 14)...(F) Ч 1 8 2005-05-13 5. HOW TO REPLACE FLAT PACKAGE IC 5.1. Preparation - SOLDER Sparkle Solder 115A-1, 115B-1 or Almit Solder KR-19,KR-19RMA - Soldering iron Recommended power consumption will be between 30 W to 40 W. Temperature of Copper Rod 662 ± 50°F (350 ± 10°C) (An expert may handle between 60 W to 40 W iron, but beginner might damage foil by overheating.) - Flux HI115 Specific gravity 0.863 (Original flux will be replaced daily.) 5.2. Procedure 1. Temporary fix FLAT PACKAGE IC by soldering on two marked 2 pins. *Most important matter is accurate setting of IC to the corresponding soldering foil. 2. Apply flux for all pins of FLAT PACKAGE IC. 9 2005-05-13 3. Solder employing specified solder to direction of arrow, as sliding the soldering iron. 5.3. Modification Procedure of Bridge 1. Re-solder slightly on bridged portion. 2. Remove remained solder along pins employing soldering iron as shown in 10 2005-05-13 below figure. 6. CPU DATA (BASE UNIT) 6.1. IC201 11 2005-05-13 12 2005-05-13 7. CPUDATA (HANDSET) 7.1. IC901 13 2005-05-13 14 2005-05-13 8. E