ricoh all free download

File name SC Ricoh Aficio 2022-2027.pdf

B089/B093 SERVICE MANUAL 001783MIU RICOH GROUP COMPANIES SERVICE CALL CONDITIONS 7. TROUBLESHOOTING CAUTION Never turn off the main power switch when the power LED is lit or flashing. To avoid damaging the hard disk or memory, press the operation power switch to switch the power off, wait for the power LED to go off, and then switch the main power switch off. NOTE: The main power LED ( ) lights or flashes while the platen cover or ARDF is open, while the main machine is communicating with a facsimile or the network server, or while the machine is accessing the hard disk or memory for reading or writing data. 7.1 SERVICE CALL CONDITIONS 7.1.1 SUMMARY There are 4 levels of service call conditions. Level A Definition To prevent damage to the machine, the main machine cannot be operated until the SC has been reset by a service representative (see the note below). SCs that disable only the features that use the defective item. Although these SCs are not shown to the user under normal conditions, they are displayed on the operation panel only when the defective feature is selected. The SC history is updated. The machine can be operated as usual. Turning the main switch off then on resets SCs displayed on the operation panel. These are redisplayed if the error occurs again. Reset Procedure Enter SP mode, and then turn the main power switch off and on. Turn the operation switch or main switch off and on. B C D The SC will not be displayed. Only the SC history is updated. Turn the operation switch off and on. SM 7-1 B089/B093 Troubleshooting NOTE: 1) If the problem concerns electrical circuit boards, first disconnect then reconnect the connectors before replacing the PCBs. 2) If the problem concerns a motor lock, first check the mechanical load before replacing motors or sensors. SERVICE CALL CONDITIONS 7.1.2 SC CODE DESCRIPTIONS Code No. 101 B Symptom Exposure lamp error The standard white level was not detected properly when scanning the white plate. · · · · · · · · · · · · · 121 D Scanner home position error 2 The scanner home position sensor does not detect the off condition during initialization. · · · · · · · 122 B Scanner HP Sensor ­ Error 1 The HP sensor remains on while the carriage is returning to the home position. · · · · · · 123 B Scanner HP sensor ­ Error 2 The HP sensor does not switch on after the carriage has returned to the home position. · · · · · · Possible Cause Exposure lamp defective Lamp stabilizer defective Exposure lamp connector defective Standard white plate dirty Scanner mirror or scanner lens out of position or dirty SBU defective Scanner drive motor defective Scanner motor defective Harness between SBCU and scanner drive motor disconnected Harness between SBCU and scanner drive motor power source disconnected Scanner HP sensor defective Harness between SBCU and HP sensor disconnected Scanner wire, timing belt, pulley, or carriage defective SIB or scanner drive motor defective Scanner motor defective Harness betw

File name SC Ricoh Aficio 1018D.pdf

Model K-C1 (Machine Code: B039/B040/B043) SERVICE MANUAL February 20th, 2001 Subject to change 20 February, 2001 SERVICE CALL CONDITIONS 4. TROUBLESHOOTING 4.1 SERVICE CALL CONDITIONS 4.1.1 SUMMARY There are 2 levels of service call conditions. Level Definition To prevent the machine from being damaged, the SC can only be reset by a service representative. The copier cannot be operated at all. The SC can be reset by turning the main power switch off and on. Reset Procedure Enter SP 5-810 (SC code reset) and select "1". Then hold down the Original type key and the OK or ! key at the same time (this does not require the main switch to be turned off and on). Turn the main power switch off and on. A B NOTE: 1) If the problem concerns electrical circuit boards, first disconnect then reconnect the connectors before replacing the PCBs. 2) If the problem concerns a motor lock, first check the mechanical load before replacing motors or sensors. 4-1 Troubleshooting SERVICE CALL CONDITIONS 20 February, 2001 4.1.2 SC CODE DESCRIPTIONS No. Definition 101 B Symptom Exposure Lamp Error The standard white level was not detected properly when scanning the white plate. Possible Cause · Exposure lamp defective · Exposure lamp stabilizer defective · Exposure lamp connector defective · Dirty scanner mirror or scanner mirror out of position · SBU board defective · SBU connector defective · Lens block out of position · Incorrect position or width of white plate scanning ( SP4-015) · Scanner home position sensor defective · Scanner drive motor defective · Scanner home position sensor connector defective · Scanner drive motor connector defective · IOB board defective · Scanner home position sensor defective · Scanner drive motor defective · Scanner home position sensor connector defective · Scanner drive motor connector defective · IOB board defective · Scanner home position sensor defective · Scanner drive motor defective · Scanner home position sensor connector defective · Scanner drive motor connector defective · IOB board defective · Scanner home position sensor defective · Scanner drive motor defective · Scanner home position sensor connector defective · Scanner drive motor connector defective · IOB board defective 120 B Scanner home position error 1 The scanner home position sensor does not detect the off condition during initialization or copying. 121 B Scanner home position error 2 The scanner home position sensor does not detect the on condition during initialization or copying. 122 B Scanner home position error 3 The scanner home position sensor detects the on condition while the scanner is returning to the home position. 123 B Scanner home position error 4 The scanner home position sensor does not detect the on condition after the scanner returns to the home position. 4-2 20 February, 2001 No. Definition 130 B Symptom SERVICE CALL CONDITIONS Possible Cause 192 B 194 B 302 B 320 B 321 B Communication Error between BiCU and

File name SC ricoh Aficio 1113 Espaсol.pdf

MANUAL DE SERVICIO RICOH AFICIO 1113 / 1015 /1018 / 2015 / 2018 LANIER LD 013 /015 / 018 /122 GESTETNER 7413 Autor: Arnol Montes Avila 1 MANUAL DE SERVICIO CONDICIONES DE SERVICIO SUMARIO Hay niveles de condiciones de llamada de servicio. Nivel · A · · B Definiciуn Para prevenir que la maquina se daсe, el SC puede ser restablecido sуlo por un representante del servicio Tйcnico. La copiadora no puede operarse en absoluto. El SC puede ser restablecido Apagando y encendiendo la Maquina. Restablezca Procedimiento Entre en el SP 5-810 (Cуdigo del SC de reset el seleccionado) y "1". Entonces presione la tecla de Tipo de Original y el OK al mismo tiempo (esto ningъn no exige apagar el interruptor principal). Apagando y encendiendo la maquina NOTA: 1. Si el problema involucra que el circuito elйctrico de la board, Primero desconecte los conectores antes de reemplazar el PCBs. 2. Si el problema involucra una cerradura de motor, primero verifique La carga mecбnica antes de reemplazar motores o censores. Autor: Arnol Montes Avila 2 DESCRIPCIУN DE LOS CУDIGOS SC Nє Definiciуn Sнntoma · · · · · · · · Posibles Causas Error del la Lбmpara de Exposiciуn 101 B 120 B Lбmpara de la exposiciуn defectuosa. Estabilizador de la lбmpara de exposiciуn defectuoso. Conector de la lбmpara de exposiciуn defectuosa. El nivel blanco normal no fue Espejo del escбner sucio o espejo del escбner fuera de posiciуn. descubierto apropiadamente al SBU de la board defectuoso. examinar el parche blanco. Conector del SBU defectuoso. Cerradura de la lente fuera de posiciуn. Posiciуn incorrecta o anchura de plato blanco que examina (SP 4015) Posiciуn del inicio Escбner Error 1 · posiciуn del censor defectuoso. El censor de posiciona del escбner · El escбner maneja la salida de guнa defectuoso. no descubre el fuera de la · Posiciуn de casa del censor defectuoso. condiciуn durante la inicializaciуn · El escбner que maneja el conector de motor defectuoso o copiando. · IOB de la board defectuoso. Posiciуn de casa de escбner error 2 · posiciуn de casa del escбner defectuoso. · El escбner que maneja el riel defectuoso. · Conector del censor de casa del escбner defectuoso. · El escбner maneja conector de motor defectivo. · IOB de la board defectuoso. Posiciуn de casa de escбner error 3 · Censor de la casa del escбner defectuoso. · El escбner maneja riel de guнa defectuoso. · Conector del censor de casa del escбner esta defectuoso. · El escбner maneja conector de motor defectuoso. · IOB de la board defectuoso. Posiciуn de casa de escбner error 3 121 B La casa de posiciуn del censor del escбner no descubre el en la condiciуn durante la inicializaciуn o copiando. 122 B La casa del escбner que posiciona el censor descubre la condiciуn mientras el escбner estб devolviendo a las posiciones de la casa. 123 B La casa del escбner posiciona el censor no descubre el en la condiciуn despuйs del escбner devuelve a la posiciуn de la casa. 130 B 192 B · Censor de posiciуn de cas

File name SC Ricoh Aficio 2015.pdf

B121/B122/B123 SERVICE MANUAL 001874MIU RICOH GROUP COMPANIES SERVICE CALL CONDITIONS 4. TROUBLESHOOTING 4.1 SERVICE CALL CONDITIONS 4.1.1 SUMMARY There are four levels of service call conditions. Level A Definition To prevent damage to the machine, the main machine cannot be operated until the SC has been reset by a service representative (see the note below). If the SC was caused by incorrect sensor detection, the SC can be reset by turning the main power switch off and on. The main machine can be operated as usual, excluding the unit related to the service call. The SC history is updated. The machine can be operated as usual. Reset Procedure Enter SP mode, and then turn the main power switch off and on. Turn the main power switch off and on. Turn the main power switch off and on. The SC will not be displayed. Only the SC history is updated. Troubleshooting B C D NOTE: 1) If the problem concerns electrical circuit boards, first disconnect then reconnect the connectors before replacing the PCBs. 2) If the problem concerns a motor lock, first check the mechanical load before replacing motors or sensors. SM 4-1 B121/B122/B123 SERVICE CALL CONDITIONS 4.1.2 SC CODE DESCRIPTIONS No. Definition 101 B Symptom Exposure Lamp Error The standard white level was not detected properly when scanning the white plate. Possible Cause · Exposure lamp defective · Exposure lamp stabilizer defective · Exposure lamp connector defective · Dirty scanner mirror or scanner mirror out of position · SBU board defective · SBU connector defective · Lens block out of position · Incorrect position or width of white plate scanning (! SP4-015) · Scanner home position sensor defective · Scanner drive motor defective · Scanner home position sensor connector defective · Scanner drive motor connector defective · BICU board defective · Scanner home position sensor defective · Scanner drive motor defective · Scanner home position sensor connector defective · Scanner drive motor connector defective · BICU board defective 120 B Scanner home position error 1 The scanner home position sensor does not detect the off condition during initialization or copying. 121 B Scanner home position error 2 The scanner home position sensor does not detect the on condition during initialization or copying. 143 D SBU white/black level correction error The automatic SBU adjustment has failed to correct the black level. The automatic SBU adjustment has failed to correct the white level twenty times consecutively. 144 B · Exposure lamp defective · Dirty white plate · Incorrect position or width of white plate scanning (! SP4-015) · BICU board defective · SBU board defective Communication Error between BICU and SBU The BICU board cannot detect the SBU · The flat cable between the BICU connect signal. board and the SBU has a poor connection · The flat cable between the BICU board and the SBU is damaged · BICU board defective · SBU defective B121/B122/B123 4-2 SM SERVICE CALL CONDITION

File name SC Ricoh Aficio 2020-3025.pdf

AJUSTES DE COPIA: IMPRESIУN/EXPLORACIУN 10 de agosto de 2001 6.8.4 CALIBRACIУN DE LA PANTALLA TБCTIL Despuйs de borrar la memoria o si la funciуn de detecciуn del panel tбctil no funciona correctamente, siga este procedimiento para calibrar la pantalla tбctil. NOTA: no intente utilizar los elementos del [2] al [9] del menъ de autodiagnуstico. Estos elementos se utilizan en el momento del diseсo. 1. Pulse ", pulse #$$% y, despuйs, pulse & 5 veces para abrir el menъ de autodiagnуstico (Self-Diagnostics). B027R533.WMF B027R554.WMF 2. En la pantalla tбctil, presione Ajuste de la pantalla tбctil (Touch Screen Adjust) o pulse #. 3. Utilice un objeto con punta (no afilada) para presionar la marca superior izquierda . 4. Pulse la marca inferior derecha despuйs de que aparezca. 5. Toque en algunos puntos del panel tбctil para comprobar que el marcador (+) aparece exactamente donde se toca la pantalla. Si la marca + no aparece en el lugar de la pantalla donde se ha tocado, pulse Cancelar (Cancel) y repita el procedimiento desde el paso 2. 6. Cuando haya acabado, presione [#] OK en la pantalla (o pulse '). 7. Toque en [#] Exit (Salir) en la pantalla para cerrar el menъ de autodiagnуstico (Self-Diagnostic) y guardar los ajustes de calibraciуn. 6-42 10 de agosto de 2001 CONDICIONES DE LAS LLAMADAS AL SERVICIO TЙCNICO 7. LOCALIZACIУN DE AVERНAS !PRECAUCIУN No apague el interruptor de alimentaciуn principal cuando el LED de alimentaciуn estй encendido o parpadee. Para evitar daсar el disco duro o la memoria, pulse el interruptor de alimentaciуn de funcionamiento para desconectar la alimentaciуn, espere a que el LED de alimentaciуn se apague y despuйs desconecte el interruptor de alimentaciуn principal. NOTA: el LED de alimentaciуn principal ( ) se enciende o parpadea cuando el cristal de exposiciуn o el ARDF estбn abiertos, cuando la mбquina principal se estб comunicando con una mбquina de fax o con el servidor de la red, o cuando la mбquina intenta acceder al disco duro o a la memoria para leer o escribir datos. 7.1.1 RESUMEN Las condiciones de las llamadas al servicio tйcnico pueden agruparse en cuatro niveles diferentes. Nivel Definiciуn Para evitar que la mбquina se estropee, no se puede poner en marcha la mбquina principal hasta que un representante del servicio tйcnico haya restablecido el SC (vea la nota a continuaciуn de la tabla). SC que sуlo desactivan las funciones utilizadas por el elemento defectuoso. Aunque en condiciones normales el usuario no ve estos SC, aparecen en el panel de mandos cuando se selecciona la funciуn defectuosa. El histуrico de SC se actualiza. La mбquina puede utilizarse con normalidad. Al apagar el interruptor principal y luego encenderlo se reinician los SC en el panel de mandos. Se vuelven a mostrar si se repite el error. Procedimiento de reinicio Active el modo SP y apague y encienda el interruptor de alimentaciуn principal. A B Apague y encienda el interruptor de funcionamiento o el interruptor principal. El c

File name SC Ricoh Aficio 340 - 350 - 450.pdf

A230/A231/A232 SERVICE MANUAL RICOH GROUP COMPANIES PN: RCSMA232 SERVICE CALL CONDITIONS 7. TROUBLESHOOTING 7.1 SERVICE CALL CONDITIONS 7.1.1 SUMMARY There are 4 levels of service call conditions. Level A Definition To prevent the machine from being damaged, the SC can only be reset by a service representative (see the note below). The copier cannot be operated at all. The SC can be reset by turning the main power switch off and on if the SC was caused by incorrect sensor detection. Reset Procedure Enter SP mode, then turn the main power switch off and on. Turn the operation switch or main power switch off and on. A level B' SC can only be reset by turning the main power switch off and on. Turn the operation switch off and on. The SC will not displayed. All that happens is that the SC history is updated. B C D The copier can be operated as usual except for the unit related to the service call. The SC history is updated. The machine can be operated as usual. NOTE: 1) If the problem concerns electrical circuit boards, first disconnect then reconnect the connectors before replacing the PCBs. 2) If the problem concerns a motor lock, first check the mechanical load before replacing motors or sensors. 3) When a Level A or B SC occurs while in an SP mode, the display does not indicate the SC number. If this occurs, check the SC number after leaving the SP mode. This does not apply to Level B' codes. SM 7-1 A230/A231/A232 Trouble shooting SERVICE CALL CONDITIONS 7.1.2 SC CODE DESCRIPTIONS SC101: Exposure lamp error - Definition - [B] The standard white level was not detected properly when scanning the white plate. - Possible cause · Exposure lamp defective · Lamp stabilizer defective · Exposure lamp connector defective · Dirty standard white plate · Dirty scanner mirror or scanner mirror out of position · SBU board defective · SBU connector defective · Lens block out of position · SIB defective SC120: Scanner home position error 1 -Definition- [B'] The scanner home position sensor does not detect the on condition during initialization or copying. - Possible causes · Scanner home position sensor defective · Scanner drive motor defective · SIB defective · Scanner home position sensor connector defective · Scanner drive motor connector defective SC121: Scanner home position error 2 -Definition- [B'] The scanner home position sensor does not detect the off condition during initialization or copying. - Possible causes · Scanner home position sensor defective · Scanner drive motor defective · SIB defective · Scanner home position sensor connector defective · Scanner drive motor connector defective A230/A231/A232 7-2 SM SERVICE CALL CONDITIONS SC302: Charge roller current leak -Definition- [B] A charge roller current leak signal is detected. - Possible causes · Charge roller damaged · High voltage supply board defective · Poor PCU connection SC 304: Charge roller current correction error -Definition- [B] The charge roller bias correction is pe

File name SC Ricoh Aficio 350e 450e.pdf

A283/A284 SUPPLEMENTAL SERVICE MANUAL (To be used in conjunction with A230/A231/232 Service Manual) 000958MIU RICOH GROUP COMPANIES SERVICE CALL CONDITIONS 7. TROUBLESHOOTING 7.1 SERVICE CALL CONDITIONS 7.1.1 SUMMARY There are 4 levels of service call conditions. Level A Definition To prevent the machine from being damaged, the SC can only be reset by a service representative (see the note below). The copier cannot be operated at all. The SC can be reset by turning the main power switch off and on if the SC was caused by incorrect sensor detection. Reset Procedure Enter SP mode, then turn the main power switch off and on. B C D The copier can be operated as usual except for the unit related to the service call. The SC history is updated. The machine can be operated as usual. Turn the operation switch or main power switch off and on. A level B' SC can only be reset by turning the main power switch off and on. Turn the operation switch off and on. The SC will not displayed. All that happens is that the SC history is updated. NOTE: 1) If the problem concerns electrical circuit boards, first disconnect then reconnect the connectors before replacing the PCBs. 2) If the problem concerns a motor lock, first check the mechanical load before replacing motors or sensors. 3) When a Level A or B SC occurs while in an SP mode, the display does not indicate the SC number. If this occurs, check the SC number after leaving the SP mode. This does not apply to Level B' codes. SM 7-1 A283/A284 Troubleshooting SERVICE CALL CONDITIONS 7.1.2 SC CODE DESCRIPTIONS SC101: Exposure Lamp Error Definition [B] The standard white level was not detected properly when scanning the white plate. Possible Cause · Exposure lamp defective · Lamp stabilizer defective · Exposure lamp connector defective · Dirty standard white plate · Dirty scanner mirror or scanner mirror out of position · SBU board defective · SBU connector defective · Lens block out of position · SIB defective SC120: Scanner Home Position Error 1 Definition [B'] The scanner home position sensor does not detect the on condition during initialization or copying. Possible Causes · Scanner home position sensor defective · Scanner drive motor defective · SIB defective · Scanner home position sensor connector defective · Scanner drive motor connector defective SC121: Scanner Home Position Error 2 Definition [B'] The scanner home position sensor does not detect the off condition during initialization or copying. Possible Causes · Scanner home position sensor defective · Scanner drive motor defective · SIB defective · Scanner home position sensor connector defective · Scanner drive motor connector defective A283/A284 7-2 SM SERVICE CALL CONDITIONS SC302: Charge Roller Current Leak Definition [B] A charge roller current leak signal is detected. Possible Causes · Charge roller damaged · High voltage supply board defective · Poor PCU connection SC 304: Charge Roller Current Correction Error Definition [B]

File name SC Ricoh Aficio 550 - 650.pdf

A229 SERVICE MANUAL RICOH GROUP COMPANIES PN: RCSMA229 SERVICE CALL CONDITIONS 6. TROUBLESHOOTING 6.1 SERVICE CALL CONDITIONS 6.1.1 SUMMARY There are 4 levels of service call conditions. Level A Definition To prevent the machine from being damaged, the SC can only be reset by a service representative (see the note below). The copier cannot be operated at all. The SC can be reset by turning the main power switch off and on if the SC was caused by incorrect sensor detection. Reset Procedure Enter SP mode, then turn the main power switch off and on. Turn the operation switch or main power switch off and on. A level B' SC can only be reset by turning the main power switch off and on. Turn the operation switch off and on. The SC will not be displayed. All that happens is that the SC history is updated. B C D The copier can be operated as usual except for the unit related to the service call. The SC history is updated. The machine can be operated as usual. NOTE: 1) If the problem concerns electrical circuit boards, first disconnect then reconnect the connectors before replacing the PCBs. 2) If the problem concerns a motor lock, first check the mechanical load before replacing motors or sensors. 3) When a Level A or B SC occurs while in an SP mode, the display does not indicate the SC number. If this occurs, check the SC number after leaving the SP mode. This does not apply to Level B' codes. Troubleshooting SM 6-1 A229 SERVICE CALL CONDITIONS 6.1.2 SC CODE DESCRIPTIONS SC101: Exposure lamp error - Definition - [B] The standard white level was not detected properly when scanning the white plate. - Possible cause · Exposure lamp defective · Lamp regulator defective · Exposure lamp connector defective · Dirty standard white plate · Dirty scanner mirror or scanner mirror out of position · SBU board defective · SBU connector defective · Lens block out of position SC120: Scanner home position error 1 -Definition- [B] The scanner home position sensor does not detect the on condition during initialization or copying. - Possible causes · Scanner home position sensor defective · Scanner motor defective · Scanner motor drive board defective · Scanner home position sensor connector defective · Scanner drive motor connector defective SC121: Scanner home position error 2 -Definition- [B] The scanner home position sensor does not detect the off condition during initialization or copying. - Possible causes · Scanner home position sensor defective · Scanner drive motor defective · Scanner motor drive board defective · Scanner home position sensor connector defective · Scanner drive motor connector defective A229 6-2 SM SERVICE CALL CONDITIONS SC302-01: Charge corona output error 1 -Definition- [B] The feedback voltage from the charge corona unit is too high. - Possible causes · Charge P.P. defective · Poor charge corona unit connection SC302-02: Charge corona output error 2 -Definition- [B] The control PWM for the charge corona unit is too high. - Poss

File name SC Ricoh Aficio 700.pdf

8 de enero de 2000 CONDICIONES DE LAS LLAMADAS AL SERVICIO TЙCNICO 7. LOCALIZACIУN DE AVERНAS 7.1 CONDICIONES DE LAS LLAMADAS AL SERVICIO TЙCNICO 7.1.1 RESUMEN Las condiciones de llamadas de servicio pueden agruparse en cuatro niveles diferentes. Nivel A Definiciуn Para evitar que la mбquina se estropee, el cуdigo SC sуlo puede reiniciarlo un representante del servicio tйcnico (ver nota a continuaciуn de la tabla). La copiadora no puede utilizarse. El cуdigo SC puede reiniciarse apagando y encendiendo el interruptor de alimentaciуn principal, si el cуdigo SC ha sido consecuencia de la detecciуn incorrecta de un sensor. Procedimiento de reinicio Entre el modo SP y apague y encienda el interruptor de alimentaciуn principal. B L D La copiadora puede utilizarse con normalidad excepto la unidad que estй relacionada con la llamada de servicio. El histуrico de SC se actualiza. La mбquina puede utilizarse con normalidad. Apague y encienda el interruptor de funcionamiento o el interruptor de alimentaciуn principal. Un cуdigo SC de nivel B' sуlo puede reiniciarse apagando y encendiendo el interruptor de alimentaciуn principal. Apague y encienda el interruptor de funcionamiento. El cуdigo SC no se visualizarб. Lo ъnico que ocurre es que se actualiza el histуrico de SC. NOTA: 1) Si el problema estб relacionado con las placas de circuitos elйctricos, primero desconecte los conectores y vuelva a conectarlos antes de sustituir las placas de circuitos impresos (PCB). 2) Si el problema estб relacionado con un bloqueo de motor, antes de sustituir motores o sensores compruebe la carga mecбnica. 3) Si se produce un cуdigo SC de nivel A o B mientras estб en un modo SP, no se indicarб el nъmero de SC en el display. Si se da este caso, anote el nъmero del SC antes de abandonar el modo SP. Esto no es aplicable a los cуdigos de nivel B'. 7-1 Localizaciуn de Averнas CONDICIONES DE LAS LLAMADAS AL SERVICIO TЙCNICO 8 de enero de 2000 7.1.2 DESCRIPCIONES DE LOS CУDIGOS SC SC101: Error de lбmpara de exposiciуn - Definiciуn - [B] El nivel de blanco estбndar no se ha detectado correctamente al explorar la placa blanca. - Posibles causas · Lбmpara de exposiciуn defectuosa · Regulador de la lбmpara defectuoso · Conector de la lбmpara de exposiciуn defectuoso · Placa blanca estбndar sucia · Espejo del escбner sucio o en posiciуn incorrecta · Circuito BCU defectuoso · Conector de SBU defectuoso · Bloque de lentes en posiciуn incorrecta SC120: Error de posiciуn de reposo de escбner 1 - Definiciуn - [B] El sensor de posiciуn de reposo del escбner no detecta la condiciуn de activado durante la inicializaciуn o la operaciуn de copia. - Posibles causas · Sensor de posiciуn de reposo del escбner defectuoso · Motor del escбner defectuoso · Circuito de accionamiento del motor del escбner defectuoso · Conector del sensor de posiciуn de reposo del escбner defectuoso · Conector del motor de accionamiento del escбner defectuoso SC121: Error de posiciуn de reposo de escбner 2 - Def

File name SC Ricoh Aficio1045.pdf

26 de enero de 2001 AJUSTES DE COPIA: IMPRESIУN/EXPLORACIУN 3.21.4 CALIBRACIУN DE LA PANTALLA TБCTIL Tras borrar la memoria, o si la caracterнstica de detecciуn del panel tбctil no funciona correctamente, siga este procedimiento para calibrar la pantalla tбctil. NOTA: No utilice los elementos [2] a [9] del menъ Autodiagnуstico (SelfDiagnostic). Estos elementos son sуlo para diseсo. y, a continuaciуn, - cinco veces para abrir el 1. Pulse 6, menъ Autodiagnуstico. B004R503.WMF 2. En la pantalla tбctil, pulse "Ajuste de pantalla tбctil (Touch Screen Adjust)" (o pulse ). B004R504.WMF 3. Utilice una herramienta con punta (sin afilar) para pulsar la marca superior izquierda . 4. Pulse la marca inferior derecha cuando aparezca. 5. Toque algunos puntos en el panel tбctil para confirmar que aparece la marca (+) exactamente donde se toca la pantalla. Si no aparece la marca + donde se toca la pantalla, pulse Cancelar (Cancel) y repita el proceso desde el paso 2. 6. Cuando termine, pulse [#] OK en la pantalla (o pulse ). 7. Toque en [#] Salir (Exit) en la pantalla para cerrar el menъ Autodiagnуstico y guardar los ajustes de calibraciуn. 3-79 S u s titu c iу n y Aju ste 26 de enero de 2001 CONDICIONES DE LAS LLAMADAS AL SERVICIO TЙCNICO 4. LOCALIZACIУN DE AVERНAS PRECAUCIУN No apague nunca el interruptor principal si el LED de encendido estб encendido o parpadea. Para evitar daсos en el disco duro o la memoria, pulse el interruptor de funcionamiento para apagar el equipo, espere que se apague el LED y, finalmente, apague el interruptor principal. NOTA: el LED de encendido principal ( ) se enciende o parpadea cuando el cristal de exposiciуn o el ARDF estб abierto, cuando la mбquina principal se estб comunicando con un fax o el servidor de red, o cuando la mбquina estб accediendo al disco duro o la memoria para leer o escribir datos. 4.1 CONDICIONES DE LAS LLAMADAS AL SERVICIO TЙCNICO 4.1.1 RESUMEN Las condiciones de las llamadas al servicio tйcnico pueden agruparse en cuatro niveles diferentes. Nivel Definiciуn Para evitar que la mбquina se estropee, la mбquina principal no se debe accionar hasta que un representante del servicio tйcnico haya reiniciado el cуdigo SC (ver nota a continuaciуn de la tabla). Si el cуdigo SC es consecuencia de la detecciуn incorrecta de un sensor, el cуdigo SC puede reiniciarse apagando y encendiendo el interruptor de alimentaciуn principal. La mбquina principal puede utilizarse con normalidad excepto la unidad que estй relacionada con la llamada de servicio. El histуrico de SC se actualiza. La mбquina puede utilizarse con normalidad. Procedimiento de reinicio Entre al modo SP y apague y encienda el interruptor de alimentaciуn principal. L o ca liza c iу n d e Av e rнa s A B C Apague y encienda el interruptor de funcionamiento o el interruptor de alimentaciуn principal. Apague y encienda el interruptor de funcionamiento. El cуdigo SC no se visualizarб. Sуlo se actualiza el histуrico de SC. D NOTA: 1) Si el probl