LG Flatron 795FT Plus free download

File name FB795B_1.pdf

SPECIFICATIONS 1. PICTURE TUBE Size DefIection Angle Neck Diameter Phosphor Slot Pitch Low Radiation Face Treatment 3-2. Power Consumption : 17 inch (Flat Slot Mask) : 90° : 29.1 mm : P22 : 0.24 mm : TCO-99 : W-ARASC (Anti-Reflection and Anti-Static Coating), Internal Anti-Glare MODE NORMAL (ON) STAND-BY SUSPEND OFF H/V SYNC ON/ON OFF/ON ON/OFF OFF/OFF POWER CONSUMPTION LED COLOR GREEN ORANGE less than 130W less than 8W less than 8W less than 3W ORANGE 2. SIGNAL 2-1. Horizontal & Vertical Sync 1) Input Voltage Level : Low= 0.8V, High= 2.1V 2) Sync Polarity : Positive or Negative 2-2. Video Input Signal 1) Voltage Level a) Color 0, 0 b) Color 7, 0 c) Color 15, 0 2) Input Impedance 3) Video Color 4) Signal Format 4. DISPLAY AREA 4-1. Active Video Area : 310 x 230 mm (12.20" x 9.06") (Available for Full Screen) 4-2. Display Color : Full Colors 4-3. Display Resolution : 1600 Dots x 1200Lines 4-4. Video Bandwidth : 203MHz 5. ENVIRONMENT 5-1. Operating Temperature: 10°C ~ 35°C (50°F ~ 95°F) (Ambient) 5-2. Relative Humidity : 8% ~ 80% (Non-condensing) 5-3. Altitude : 10,000 ft 6. DIMENSIONS (with TILT/SWIVEL) Width : 415.0 mm (16.34") Depth : 435.0 mm (17.13") Height : 438.8 mm (17.28") 7. WEIGHT (with TILT/SWIVEL) Net Weight : 21.0 kg (46.30 lbs) Gross Weight : 24.5 kg (54.02 lbs) 8. USB Specifications USB Standard : Rev. 1.0 complied self-powered hub Downstream power supply : 500mA for each (MAX) Communication speed : 12 Mbps (Full), 1.5 Mbps (Low) USB port : 1 Upstream port 4 Downstream ports : 0 ~ 0.7 Vp-p : 0 Vp-p : 0.467 Vp-p : 0.7 Vp-p : 75 : R, G, B Analog : Refer to the Timing Chart 2-3. Signal Connector 15 Pin D-Sub Connector 2-4. Scanning Frequency Horizontal : 30 ~ 96 kHz Vertical : 50 ~ 160 Hz 3. POWER SUPPLY 3-1. Power Range AC 100 ~ 120V/200~240V (Auto Select), 50/60Hz, 2.0/1.0A Max. -2-

File name FB795B_10.pdf

DISASSEMBLY 1. TILT/SWIVEL REMOVAL 1) Set the monitor face downward. 2) Pressing the latch (a), carefully remove the Tilt/Swivel by pulling it upward. (a) 2. BACK COVER REMOVAL 1) Remove four screws (a) from the Back Cover. 2) Slide the Back Cover away from the Front Cabinet of the monitor. (a) (a) 3. TOP SHIELD REMOVAL 1) Remove six screws (a). 2) Remove four screws (b). 3) Remove two screws (c). 4) Remove two screws (d). (a) (b) (a) (a) (a) (a) (b) (a) (a) (c) (a) (d) (b) (d) (b) (c) - 11 - 4. TOTAL CHASSIS ASSEMBLY REMOVAL 1) Disconnect P903 (Degaussing pin), P704 (DY pin), P609 (Tilt pin), and P610 (Purity pin) from the Main PCB. 2) Disconnect P306 (GND Wire), P304,P305 from the Video PCB. 3) Carefully separate the CDT Board Assembly from the CDT neck. 4) Discharge the remaining static electricity by shorting between the Anode Cap and the CDT ground. 5) Disconnect the Anode Cap from the CDT. 6) Remove four screws (a). 7) Remove the Total Chassis Assembly from the Main Frame. Anode Cap P306 (a) P304,P305 P704 P903 P609 P610 (a) (a) (a) 5. VIDEO PCB ASSEMBLY REMOVAL 1) Disconnect P301, P303, P310, and P319 from the Video PCB. 2) Remove the Video PCB Assembly from the Interface Assembly. 6. BOTTOM BRACKET REMOVAL 1) Remove five screws (a). 2) Remove the Bottom Bracket. (a) P319 P301 P310 P303 (a) (a) (a) Bottom Bracket - 12 - 7. MAIN BRACKET & CONTROL PCB ASS'Y REMOVAL 1) Remove nine screws (a). 2) Remove two screws (b). 3) Carefully remove the Interface Assembly from the Main PCB Board. 4) Remove the Control PCB Assembly from the Main Mracket. 5) Release four latches (d) from the Main Board Assembly. 6) Remove the Bottom Bracket. (a) Interface Ass'y (a) (a) (a) (a) (a) (a) (a) (b) (b) (a) (a) (d) Control PCB Ass'y (d) Main Bracket 8. INTERFACE ASSEMBLY REMOVAL 1) Remove five screws (a). 2) Remove Interface Rear Shield. 3) Remove three screws (b). 4) Remove the Interface Front Shield and Interface PCB. Shield, Interface Rear (a) (a) (b) Interface PCB Total (a) (a) (a) Shield, Interface Front (b) - 13 -

File name FB795B_2.pdf

TIMING CHART VIDEO B A C E D F SYNC << Horizontal Frequency (kHz), Vertical Frequency (Hz), Horizontal etc... (µs), Vertical etc... (ms) >> Mode H/V Sort Sync Polarity Frequency Total Period (E) Video Active Blanking Time Sync Duration Time (A) (D) (B) Back Porch (F) Front Porch (C) Resolution 720x400 70Hz 640x480 60Hz 640x480 85Hz 832x624 75Hz 800x600 85Hz 1024x768 75Hz 1024x768 85Hz 1152x870 75Hz 1152x864 85Hz 1280x1024 75Hz 1280x1024 85Hz 1600x1200 75Hz 600x500 50Hz 720x540 160Hz 992x700 60Hz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 H V H V H V H V H V H V H V H V H V H V H V H V H V H V H V ­ + ­ ­ ­ ­ ­ ­ + + + + + + ­ ­ + + + + + + + + + + + + ­ ­ 31.469 70.082 31.469 59.940 43.269 85.008 49.725 74.550 53.674 85.061 60.023 75.029 68.677 84.997 68.681 75.062 77.487 85.057 79.976 75.025 91.146 85.024 93.750 75.000 29.990 49.990 96.060 160.100 48.380 60.020 31.778 14.270 31.778 16.683 23.112 11.763 20.111 13.414 18.631 11.756 16.660 13.328 14.561 11.765 14.560 13.322 12.905 11.757 12.504 13.329 10.971 11.762 10.666 13.333 33.340 20.004 10.410 6.246 20.675 16.668 25.422 12.713 25.422 15.253 17.778 11.093 14.525 12.549 14.222 11.178 13.003 12.795 10.836 11.183 11.520 12.667 9.481 11.150 9.481 12.804 8.127 11.235 7.901 12.800 24.400 16.670 7.510 5.621 15.260 14.476 6.356 1.557 6.356 1.430 5.334 0.670 5.586 0.865 4.409 0.578 3.657 0.533 3.725 0.582 3.040 0.655 3.424 0.607 3.023 0.525 2.844 0.527 2.765 0.533 8.940 3.334 2.900 0.625 5.415 2.192 3.810 0.064 3.813 0.064 1.556 0.069 1.117 0.061 1.138 0.056 1.219 0.050 1.016 0.044 1.280 0.044 1.053 0.039 1.067 0.038 1.016 0.033 0.948 0.032 2.850 0.067 1.400 0.031 2.090 0.124 1.906 1.080 1.907 1.049 2.222 0.578 3.910 0.784 2.702 0.503 2.235 0.466 2.201 0.523 1.440 0.567 1.844 0.555 1.837 0.474 1.422 0.483 1.501 0.490 3.660 2.000 0.980 0.520 2.710 1.323 0.640 0.413 0.636 0.318 1.556 0.023 0.559 0.020 0.569 0.019 0.203 0.017 0.508 0.015 0.320 0.044 0.527 0.013 0.119 0.013 0.406 0.011 0.316 0.011 2.430 1.267 0.520 0.074 0.615 0.745 -4-

File name FB795B_3.pdf

CONTROL LOCATIONS 10 9 Main PCB 8 7 Control PCB 6 4 3 5 2 1 No. 1 2 3 4 5 Ref. No. SW131 P155 P151 P137 P140 Control Function POWER SWITCH SET BUTTON OSD SELECT/ADJUSTMENT (RIGHT) OSD SELECT/ADJUSTMENT (UP) OSD SELECT/ADJUSTMENT (DOWN) No. 6 7 8 9 10 Ref. No. P157 P160 VR901 SC701 VR501 Control Function OSD SELECT/ADJUSTMENT (LEFT) OSD BUTTON B + ADJUSTMENT R-CENTER SELECT HIGH-VOLTAGE ADJUSTMENT -9-

File name FB795B_4.pdf

ADJUSTMENT GENERAL INFORMATION All adjustment are thoroughly checked and corrected when the monitor leaves the factory, but sometimes several adjustments may be required. Adjustment should be following procedure and after warming up for a minimum of 30 minutes. · Alignment appliances and tools. - IBM compatible PC. - Programmable Signal Generator. (eg. VG-819 made by Astrodesign Co.) - EPROM or EEPROM with saved each mode data. - Alignment Adaptor and Software. - Digital Voltmeter. - White Balance Meter. - Luminance Meter. - High-voltage Meter. AUTOMATIC AND MANUAL DEGAUSSING The degaussing coil is mounted around the CDT so that automatic degaussing when turn on the monitor. But a monitor is moved or faced in a different direction, become poor color purity cause of CDT magnetized, then press (DEGAUSSING) on the OSD menu. 4. Adjustment for Factory Mode (Preset Mode). 1) Display cross hatch pattern at Mode 14. 2) Run alignment program for Flatron 795FT plus (FB795B) on the IBM compatible PC. 3) EEPROM ALL CLEAR Y(Yes) command. 4) DIST. ADJ. SIZE-MAX command. 5) Adjust H-SIZE MAX as arrow keys to just of the full screen size at Mode 15. 6) Adjust V-SIZE MAX as arrow keys to just of the full screen size at Mode 15. 7) COMMAND PRESET STARTY(Yes) command. 8) Adjust tilt as arrow keys to be the best condition. 9) DIST. ADJ. BALANCE command. 10) Adjust balance of pin balance, key balance, V S Linearity, V C Linearity, Pin S correction and Pin W correction as arrow keys to be the best condition. 11) DIST. ADJ. FOS. ADJ command. 12) Adjust H-SIZE as arrow keys to 310±2mm. 13) Adjust H-POSITION as arrow keys to center of the screen. 14) Adjust V-SIZE as arrow keys to 230±1mm. 15) Adjust V-POSITION as arrow keys to center of the screen. 16) Adjust S-PCC (Side-Pincushion) as arrow keys to be the best condition. 17) Adjust TRAPEZOID as arrow keys to be the best condition. 18) Display from Mode 1 to Mode 12 and repeat above from number 12) to 17). 19) PRESET EXIT Y (Yes) command. 5. Adjustment for White Balance and Luminance. 1) Set the White Balance Meter. 2) Press the (DEGAUSSING) on the OSD menu for demagnetization of the CDT. 3) Display color 0,0 pattern at Mode 12. 4) Set Bright and Contrast to max position. 5) COLOR ADJ. BIAS ADJ. command of the alignment program. 6) Check whether blue color or not at R-BIAS and GBIAS to min position and B-BIAS to 127 (decimal) position at Sub-Bright Max. If it's not blue color, the monitor must repair. ADJUSTMENT PROCEDURE & METHOD - Install the cable for adjustment such as Figure 1and run the alignment program on the DOS for IBM compatible PC. - Set external Brightness and Contrast volume to max position. 1. Adjustment for B+ Voltage. 1) Display cross hatch pattern at Mode 12. 2) Adjust C951 (+) voltage to 198V±0.2V with VR901. 2. Adjustment for High-Voltage. 1) Display cross hatch pattern at Mode 12. 2) Adjust CDT Anode voltage to 26kV±0.2kV with VR501. 3. Adjustment for Horizontal Raster Center. 1) Display cr

File name FB795B_5.pdf

TROUBLESHOOTING GUIDE 1. NO POWER NO POWER (POWER INDICATOR OFF) CHECK FUSE OK? NO TROUBLE IN FUSE (F901) YES CHECK C912 (+) VOLTAGE? (250VDC) NO TROUBLE IN D901 YES CHECK Q902 DRAIN WAVEFORM (SQUARE WAVE COMES OUT?) NO TROUBLE IN IC901 or Q902 YES CHECK D921, D922, D931, D924, D925, D926 VOLTAGE? NO TROUBLE IN D921, D922, D931, D924, D925, D926 YES TROUBLE IN IC903 - 19 - 2. NO CHARACTER NO CHARACTER CHECK IC302 PIN 3, 8, 12 (12V), PIN 17 (5V)? NO TROUBLE IN P302, 5V, 12V LINE YES CHECK IC302 PIN 2, 6, 11 ? NO TROUBLE IN PC VIDEO CARD, SIGNAL CABLE YES CHECK IC302 PIN 29, 32, 35 ? NO TROUBLE IN IC302 YES CHECK IC303 PIN 2, 8, 12 ? NO TROUBLE IN Q330, Q331, Q332 YES CHECK R, G, B CATHODE VOLTAGE? NO TROUBLE IN IC303 YES TROUBLE IN CRT SOCKET - 20 - 3. NO RASTER NO VIDEO (POWER INDICATOR GREEN or ORANGE) CHECK POWER INDICATOR GREEN or ORANGE ? ORANGE TROUBLE IN P302 SIGNAL CABLE GREEN CHECK SCREEN CONTROL VOLUME OF FBT MIN. (Counter-clockwise) ROTATE SCREEN CONTROL VOLUME TO CLOCKWISE OK CHECK VOLTAGE AT D926 CATHODE (198V) D924 CATHODE (78V) IC911 OUT (12V) D932 CATHODE (7.5V)? NO TROUBLE IN PRIMARY CIRCUIT OF T901, T902 YES CHECK IC202 (MICOM) PIN 5 (5V, HIGH), IC701 PIN 16 12V (HIGH)? NO TROUBLE IN SECONDARY CIRCUIT OF T901, T902 YES TROUBLE IN IC202 (MICOM), IC701 (T/BASE), UPC1884ACT - 21 - 4. NO VERTICAL DEFLECTION NO V-DEFLECTION (ONE HORIZONTAL LINE) CHECK IC601 PIN 2 (15V)? NO TROUBLE IN T901 PIN 18 YES CHECK IC601 PIN 4 (-12V)? NO TROUBLE IN T901 PIN 15 YES CHECK IC701 PIN 8 (SAWTOOTH WAVE)? NO TROUBLE IN IC701 YES TROUBLE IN IC601, VERTICAL OUTPUT CIRCUIT - 22 - 5. TROUBLE IN DPM STAND-BY/SUSPEND/ OFF MODE FAILURE CHECK IC202 (MICOM) PIN 42, 1 (H/V INPUT) SIGNAL? INPUT H/V SYNC NO H / V SYNC SIGNAL CHECK PC, (PC IS NOT GOING INTO DPM MODE) CHECK IC202 PIN 6, 7 WAVEFORM? YES NO TROUBLE IN X201, IC202 CHECK IC202 PIN 17 (5V, HIGH)? NO TROUBLE IN IC202 YES CHECK IC902 PIN 7 (15V)? NO TROUBLE IN Q903, IC916, D914 YES CHECK B+ LINE (12V, 15V, 78V, 5V) ? NO TROUBLE IN R938 DPMS TABLE Mode TROUBLE IN T901 or PC Item H / V SYNC ON / ON OFF / ON ON / OFF OFF / OFF VIDEO NORMAL OFF(0V) OFF(0V) OFF(0V) LED GREEN ORANGE ORANGE ORANGE NORMAL STAND-BY SUSPEND OFF - 23 - 6. NO DEGAUSSING NO DEGAUSSING ( BUTTON MUST BE PRESSED.) CHECK IC202 PIN 22 (5V)? NO TROUBLE IN IC202 (MICOM) YES CHECK Q915 COLLECTOR VOLTAGE (0.5V)? YES NO TROUBLE IN D932, IC960 CHECK P903? NO TROUBLE IN P903 YES CHECK RL902? NO TROUBLE IN RL902 YES TROUBLE IN TH901, DEGAUSSING COIL - 24 - 7. NO TILT (ROTATION ) NO TILT (ROTATION) CHECK IC603 PIN 8 VOLTAGE (15V) ? NO TROUBLE IN D922 YES CHECK IC603 PIN 4 (-12V)? NO TROUBLE IN D931 YES CHECK IC603 PIN 5? NO TROUBLE IN IC202 (MICOM) YES TROUBLE IN P609, TILT COIL CONNECTOR, TILT COIL - 25 - 8. TROUBLE IN OSD NO OSD CHECK IC301 PIN 4, 9 (5V) ? NO TROUBLE IN P302, D927 YES CHECK IC301 PIN 5

File name FB795B_6-B.pdf

IIC-SCL IIC-SDA Power Off STBY & SUS H-SYNC V-SYNC 15V TILT SIGNAL -12V PURITY SIGNAL 15V H-STC V-STC 12V USBUSB+ SOG SEL SOG OFF H-SIZE H/V STC COIL 12V 78V R/G/B R/G/B H-SIZE MAX HSTC VSTC IIC-SDA IIC-SDA IIC-SCL 5V 5V BUZZ STBY DDC-SCL DDC-SDA 6.3V -12V SCL SDA 5V D-SUB (SIGNAL CABLE) STC CONTROL AN5769 (IC304) IIC SIGNAL Power OSD SET UP DOWN KEY CONTROL (IC101, IC102, IC103) HEF4013BF SUB MICOM (IC1004) MC68HC705 BDIA EEPROM 24C08 (IC207) 5V TILT CONTROL (IC603) PURITY CONTROL (IC603) LEFT RIGHT CDT MICOM DDC-SDA DDC-SCL CLAMP IIC-SCL VIDEO PRE-AMP M52743BSP (IC302) POWER AMP VPS13 (IC303) (IC202) CS1 IIC-SDA IIC-SCL OSD Signal (R/G/B) 15V -12V CS2 CS3 CS4 USB + CS4 CS0 USB ­ TILT ST-IN DEG LED 15V MUTE H-SIZE AFC V-SYNC H-SYNC V-SAW EW CONTRAST OSD PROCESSOR LSC4515 (IC301) R/G/B BIAS 115V CLAMP CONTROL D+ CS1 CS2 CS3 CS4 CS5 BLOCK DIAGRAM 15V RECTIFIER D901 H-DRV + + 198V 5V SMPS MAIN (T901) H/V SYNC PROCESSOR UPC1884ACT (IC701) 12V 12V -12V 5V 78V D/D DRIVE (IC402, Q411, 412, 413, 414) D/D CONVERTER (Q404) DUMMY FBT (T702) H-OUTPUT 2SC5047 (Q707) H-Drive Trans (T701) F/V 28V 198V D/D CONVER (Q503) 15V FLY BACK TRANS (T703) H-Drive Trans B+ Control (T701) X-RAY 15V Switching Regulator (IC902) LINE FILTER (LF901) PWM IC (IC901) 12V SMPS SUB (T902) 6.3V SCL AFC SDA DF HIGH VOLTAGE PWM IC M62501P (IC501) FBT DRIVE & SWITCHING X-RAY (Q502, 506, 507) HD FBP DF B+ H/V DETECT DYNAMIC FOCUS VR STATIC FOCUS VR SCREEN VR POWER INPUT 90~132Vac 198~264Vac (IC912) HIGH VOLTAGE DYNAMIC FOCUS STATIC FOCUS SCREEN AFC 198V - 14 R ABL C-BRT PURITY SUB-BRT DPM OFF G CS0 USB HUB (P801, 802, 803, 804, 807) D­ USB CONTROL IC(IC801) MC141555 V-OUTPUT TDA8172 (IC601) DF POWER & DPM LED SPCC & H-SIZE MIXING (IC401) 15V H-LINRARITY CORRECTION (Q712, 713, 714, 715, 718) DYNAMIC FOCUS OUTPUT LF353 (IC209) DEGAUSSING CIRCUIT (RL902) 6.3V 28V H-CENYERING COIL D-FOCUS AMP DEGAUSSING COIL DESCRIPTION OF BLOCK DIAGRAM 1. Line Filter & Associated Circuit. This is used for suppressing noise of power input line flowing into the monitor and/or some noise generated in this monitor flowing out through the power input line. That is to say, this circuit prevents interference between the monitor and other electric appliances. 2. Degaussing Circuit & Coil. The Degauss circuit consists of the degaussing coil, the PTC (Positive Temperature Coefficient thermistor, TH901), and the relay(RL902). This circuit eliminates abnormal color of the screen automatically by degaussing the slot mask in the CRT when turn on the power switch. When you need to degauss while using the monitor select (DEGAUSS) in the OPTION SELECT on the OSD menu. 3. SMPS (Switching Mode Power Supply) Circuit. This circuit works with power of 90~132Vac/180~264Vac (50/60Hz). The operation procedure is as follows: 1) AC input voltage is rectified and smoothed by the bridge diode (D901) and capacitors (C912, C913). 2) The rectified voltage (DC voltage) is app

File name FB795B_6-S.pdf

File name FB795B_6-W.pdf

WIRING DIAGRAM P103 P101 JW101 P1001 WG3 P705 P706 P102 P610 P609 P704 P210 JW1 P903 JW2 P204 P901 P205 P701 P212 P211 P206 P702 P305,P304 P303 P302 P301 P306 P319 - 10 -

File name FB795B_7.pdf

EXPLODED VIEW EXPLODED VIEW PARTS LIST 10 Ref. No. Part No. 3091TKC030A 3091TKC030B 2423GC3B41D 6868T17004B 339-002H 4951TKS035A 4951TKS035B 6140TC2005A 6140TC4001C 4814TKV007A 6871TVH097A 4920TKC021A 4814TKV008A 6174T13003E 407-T98P 6200TJB001B 407-937C 4920TKK003A 4920TKC016B 4814TKK051A 4814TKK052A 407-T98W 4920TKC003F 4920TKC003E 4814TKV024A 6871TKH004A 4814TKV021A 4810TKM034A 332-102G 4951TKK014A 4815TKT006A 4815TKT006B 3809TKC015A 3809TKC015B 332-102G 3550TKK061A 3550TKK061B 3043TKK040A 3043TKK040B 6871TVT098A 6871TKT004A 6871TMT084B 6871TST093B 3313T17032B 3313T17032D Description CABINET ASS'Y, FOR 795FT plus CABINET ASS'Y, FOR 795FT plus CDT, M41QBF423X 02N6LD CDT EARTH SCREW ASS'Y, PHP+5x20+GW18 METAL FRAME ASS'Y, FOR 795FT plus METAL FRAME ASS'Y, FOR 795FT plus DEGAUSSING COIL PURITY COIL SHIELD, VIDEO FRONT VIDEO PCB ASS'Y PLATE, HEAT SINK FOR IC303 SHIELD, VIDEO REAR FBT, Y265434 COMPRESS, HEAT SINK FOR Q503, Q507 AC SOCKET PLATE, HEAT SINK FOR D901 PLATE, HEAT SINK FOR IC902 COMPRESS, HEAT SINK FOR Q902 IC SHIELD, TOP IC SHIELD, BOTTOM COMPRESS, HEAT SINK FOR IC601 COMPRESS, HEAT SINK FOR D714, Q404, Q707 SUB HEAT SINK FOR D714, Q404, Q707 FRONT SHIELD, INTERFACE BOARD PCB ASS'Y, INTERFACE WITH USB REAR SHIELD, INTERFACE BOARD MAIN BRACKET SCREW, PTP+4x30 METAL, BOTTOM SHIELD ASS'Y TOP SHIELD ASS'Y, FOR 795FT plus TOP SHIELD ASS'Y, FOR 795FT plus BACK COVER ASS'Y, FOR 795FT plus BACK COVER ASS'Y, FOR 795FT plus SCREW, PTP+4x30 SCREW COVER, RIGHT SCREW COVER, LEFT TILT SWIVEL ASS'Y, FOR 795FT plus TILT SWIVEL ASS'Y, FOR 795FT plus PCB ASS'Y, VIDEO TOTAL PCB ASS'Y, INTERFACE TOTAL PCB ASS'Y, MAIN TOTAL PCB ASS'Y, CONTROL TOTAL MAIN TOTAL ASS'Y, FOR 795FT plus MAIN TOTAL ASS'Y, FOR 795FT plus Q'ty 1 1 1 4 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 4 1 1 1 1 1 1 1 1 AL (t=1.0) Material LGC GN5001TF UL94-5V 4 7 5 9 8 26 27 29-2 28-1 1 2 3 4 5 6-1 6-2 7 8 9 10 11 12 13 14 15 16 17-1 17-2 18 19-1 19-2 20 21 22 23 24 25 26 6-2 AL (t=1.2) AL (t=2.0) SPTE-C (t=0.3) AL (L=60) TERNE SHEET AL AL (L=70) SPTE-C (t=0.3) SPTE-C (t=0.3) AL (L=65) AL (120x80) SBHGI-A (t=1.0) SPTE (t=0.5) LGC GN5001TF UL94-5V SBHGI-A (t=1.0) AL (t=0.6) LGC GN5001TF UL94-5V 6-1 A B C 11 20 28-2 21 22 29-1 12 13 3 2 19-1 19-2 18 23 14 17-1 16 17-2 15 30 24 27 28 29-1 29-2 D E 1 25 LGC ABS 303S UL94-V0 LGC ABS 303S UL94-V0 LGC GN5001TF UL94-5V 30 A B C D E - 33 -

File name FB795B_8-C.pdf

5. CONTROL BOARD (Component Side) 6. CONTROL BOARD (Solder Side) - 30 -

File name FB795B_8-I.pdf

7. INTERFACE BOARD (Component Side) 8. INTERFACE BOARD (Solder Side) - 31 -

File name FB795B_8-MC.pdf

PRINTED CIRCUIT BOARD 1. MAIN BOARD (Component Side) - 27 -

File name FB795B_8-MS.pdf

2. MAIN BOARD (Solder Side) - 28 -

File name FB795B_8-V.pdf

3. VIDEO BOARD (Component Side) 4. VIDEO BOARD (Solder Side) - 29 -

File name FB795B_9.pdf

REPLACEMENT PARTS LIST CAUTION: BEFORE REPLACING ANY OF THESE COMPONENTS, READ CAREFULLY THE SAFETY PRECAUTIONS IN THIS MANUAL. * NOTE : S SAFETY Mark AL ALTERNATIVE PARTS MODEL: Flatron 795FT plus, 795FT plus DESCRIPTION / SPECIFICATION DATE: 1999. 2. 5. REMARK *S *AL LOC. NO. MAIN BOARD CAPACITORs C401 C402 C407 C411 C421 C424 C427 C428 C429 C431 C432 C433 C434 C435 C436 C437 C501 C502 C503 C504 C505 C506 C507 C508 C511 C512 C513 C514 C516 C518 C521 C522 C523 C524 C525 C526 C527 PART NO. 0CN1040K949 181-288M 181-304W 0CE476ER618 0CE6856K618 181-288D 0CE1076H618 0CN1040K949 0CN1020K519 0CE3376H618 0CN1040K949 0CN1210K519 0CQ1021N419 181-475A 0CN5610K519 0CE3376H618 0CE1076H618 0CN1020K519 0CQ1021N419 0CE1056K618 0CE4766H618 0CN5610K519 0CC5600K415 0CN4710K519 181-288J 0CE2266K618 0CE4766H618 0CK10302945 181-477W 0CN1030H949 181-482F 0CE1076H618 0CN2210K519 181-288D 181-309D 0CK10302945 0CE477CH618 CAPACITOR, TUBULAR(HIGH DIELEC), 0.1M 50V Z F TA52 CAPACITOR, POLYESTER, MKT 63V 105KTR PHS15105 CAPACITOR, POLYPROPYLENE, 473J 20.0*16.0*10.0*10.0 400V CAPACITOR, AL.ELECTROLYTIC, 47UF KMG 250V M FL TP 5 CAPACITOR, AL.ELECTROLYTIC, 6.8 UF SMS,SG 50V M FL CAPACITOR, POLYESTER, MKT 100V 473JTR PHS26473 CAPACITOR, AL.ELECTROLYTIC, 100M SMS 25V M FM5 TP(5) CAPACITOR, TUBULAR(HIGH DIELEC), 0.1M 50V Z F TA52 CAPACITOR, TUBULAR(HIGH DIELEC), 1000P 50V K B TA52 CAPACITOR, AL.ELECTROLYTIC, 330M SMS 25V M FL TP(5) CAPACITOR, TUBULAR(HIGH DIELEC), 0.1M 50V Z F TA52 CAPACITOR, TUBULAR(HIGH DIELEC), 120P 50V K B TA52 CAPACITOR, POLYESTER, 1000P 100V J POLY NI TP CAPACITOR, POLYPROPYLENE, 102J 11.5*10.0*6.0*5.0 100V CAPACITOR, TUBULAR(HIGH DIELEC), 560P 50V K B TA52 CAPACITOR, AL.ELECTROLYTIC, 330M SMS 25V M FL TP(5) CAPACITOR, AL.ELECTROLYTIC, 100M SMS 25V M FM5 TP(5) CAPACITOR, TUBULAR(HIGH DIELEC), 1000P 50V K B TA52 CAPACITOR, POLYESTER, 1000P 100V J POLY NI TP CAPACITOR, AL.ELECTROLYTIC, 1.0U SMS 50V M FM5 TP5 CAPACITOR, AL.ELECTROLYTIC, 47M SMS 25V M FL TP(5) CAPACITOR, TUBULAR(HIGH DIELEC), 560P 50V K B TA52 CAPACITOR, CERAMIC (TEMP. COMPENSATE), 56P 50V CAPACITOR, TUBULAR(HIGH DIELEC), 470P 50V K B TA52 CAPACITOR, POLYESTER, MKT 100V 563JTR PHS26563 CAPACITOR, AL.ELECTROLYTIC, 22M SMS 50V M FM5 TP(5) CAPACITOR, AL.ELECTROLYTIC, 47M SMS 25V M FL TP(5) CAPACITOR, CERAMIC (HIGH DIELECTRIC), 0.01UF 2KV Z F CAPACITOR, POLYPROPYLENE, 473J 19.5*15.0*8.5*7.5 250V CAPACITOR, TUBULAR(HIGH DIELEC), 0.0100UF 25V Z F TA52 CAPACITOR, POLYPROPYLENE, 274JF 18.0*17.0*10.0*7.5 250V CAPACITOR, AL.ELECTROLYTIC, 100M SMS 25V M FM5 TP(5) CAPACITOR, TUBULAR(HIGH DIELEC), 220P 50V K B TA52 CAPACITOR, POLYESTER, MKT 100V 473JTR PHS26473 CAPACITOR, POLYPROPYLENE, 182J 23.0*15.0*8.5*15.0 1.6KV CAPACITOR, CERAMIC (HIGH DIELECTRIC), 0.01UF 2KV Z F CAPACITOR, AL.ELECTROLYTIC, 470UF SHL 25V M FL TP5 - 34 - MODEL: Flatron 795FT plus, *S *AL LOC. NO. PART NO. C528 C529 C533 C534 C535 C537 C538 C539 C540 C541 C543 C552 C601 C602 C603 C604 C605 C606 C607 C608 C609 C611 C612 C613 C61