| Make | Model | Problem | Solution | Date |
| | | |
| Found: 106
|
| Beko | 15325NX | Balnk raster with white line across top - sound ok | T701 10HM Thy s/c replace with ESM740ST & C123/124 47µ 160v | 14-09-04 |
| Beko | 15325NX | Bright raster & trips to st/by | R1215 22k o/c | 14-09-04 |
| Beko | 15325NX | Dead - psu blown | Sw mode Trfmr pri s/c - replace with correct one for screen size or lack of width E/W faulty | 14-09-04 |
| Beko | 15325NX | No signals | No 30v to tuner - R61 100k o/c, D61 30v zener s/c | 14-09-04 |
| Beko | 16228NTX | Dark pic when R/C used & when OSD present | C103 220µ 400v mains smoothing cap | 14-09-04 |
| Beko | 16228NTX | Dead | Dry joints bridge rect | 14-09-04 |
| Beko | 16228NX | Pic & sound disappears soon aft sw on | Sound present if txt selected - C208 470n in if module dry joint | 14-09-04 |
| Beko | 16326NX | Dead/st/by only or partial line coll | C805 330nF 400v dry joints or burnt | 14-09-04 |
| Beko | 16328 | dead | s/c lopt use HR7218 | 14-09-04 |
| Beko | 16328NTX | Blank raster with EHT present | Dry joints T104 5v reg | 14-09-04 |
|
|
| Beko | 16328NX | Blank red raster - sound ok | No volts coll T1205 - R1215 22k 1w on crt base | 14-09-04 |
| Beko | 16328NX | Dead aft LOPTx changed | Micro SDA20563A516 faulty | 14-09-04 |
| Beko | 16328NX | Keeps auto tuning to same chan | R61 27k 2w o/c - feeds 30v zener from 200v supply | 14-09-04 |
| Beko | 16328NX | No front panel control - r/c ok | Child lock on - to remove hold "+" & "-" buttons whilst sw on tv | 14-09-04 |
| Beko | 16328NX | No mono sound | Faulty IF can - pt no BEKO63S140 | 14-09-04 |
| Beko | 16328NX | No pic unless A1 increased, then same again next time sw on | IC501 TDA4680 | 14-09-04 |
| Beko | 16328NX | poor field lin | R717 1M hi res | 14-09-04 |
| Beko | 16628NS | Dead | R105 33k 2w o/c | 14-09-04 |
| Beko | 17125T | Dead - LOPTr s/c - used S2055N | C140 .022µ 400v Was o/c | 14-09-04 |
| Beko | 17125T | Severe E-W bowing | lopt 11.1,110 CPC TFHR8007 | 14-09-04 |
| Beko | 19221NX | No mono sound | C214 150pF in IF can | 14-09-04 |
| Beko | 20230T | Diagonal white/black lines across the top 6-7 inches of the frame. | 220 ohms res , o/c or high res , mounted on the scan coils. | 14-09-04 |
| Beko | 20306NX | Dead - MOSFET 2SK1118 s/c | Only works short time aft replacement - chopper tfmr faulty | 14-09-04 |
| Beko | 2030T | Rapid tuning drift | R61 27k 2w | 14-09-04 |
| Beko | 20320 | Field collapse | Replace R734 (1k5), D704 (BA 157). | 14-09-04 |
| Beko | 20320 | No B in txt | C501 10nF on main pcb o/c | 14-09-04 |
| Beko | 20320NX | Field scan non lin - stretched at top | 220R resistor across scan coils | 14-09-04 |
| Beko | 20320NX | Line tearing at top of pic | 220R resistor across scan coils o/c | 14-09-04 |
| Beko | 20320NX | No Tuning Menu | Reset micro - Press & Hold P+/P- on set & sw on. Set comes on in service mode - then sw off | 14-09-04 |
| Beko | 20320NX | Sound pops when vol adj | IC601 TDA6610-5 | 14-09-04 |