| Make | Model | Problem | Solution | Date |
| | | |
| Found: 561
|
| Mitsubishi | CT2528 | DEAD POWER SUPPLY OUTPUT LOW | C689 ( 2 , 200uF ) SC IN AUDIO SUPPLY CCT | 14-09-04 |
| Mitsubishi | CT2531 Euro 4 | Black dots & dashes. | Drys on pin 3 earth of IC902 12v reg in PSU. | 14-09-04 |
| Mitsubishi | CT2531BM Euro 4 | AFTER REPLACING STR59041 FOUND ODD EFFECT AS IF TO | C908 10mfd 100v | 14-09-04 |
| Mitsubishi | CT2531BM Euro 4 | DOTS & DASHES NOT UNLIKE SATELLITE EFFECT! | DRY JOINT IC902 12v REG | 14-09-04 |
| Mitsubishi | CT2531BM Euro 4 | INTERFERENCE ON SCREEN LIKE BLACK SPARKLIES OR WOO | IC902 DRY JOINTED OR C920 470uF 25v | 14-09-04 |
| Mitsubishi | CT2531BM Euro 4 | Line TR s/c | Replace C908 ( 10uF ) 100V & check R903 R910 R917 for D/J | 14-09-04 |
| Mitsubishi | CT2531BM Euro 4 | No raster - sound & heaters Ok. | | 14-09-04 |
| Mitsubishi | CT2532TX | Dead - line transistor checks Ok out of cct. | LOPTX s/c bt pins 2 & chassis. | 14-09-04 |
| Mitsubishi | CT2534 | Memory loss | Chopper tfmr -31v supply corrosion on leg | 14-09-04 |
| Mitsubishi | CT2534TX Euro 4 | NO SOUND OR PICTURE + WON'T STORE STATIONS | CHECK 5v + -30v ON IC702 TRANSFORMER T951 MAYBE O/C ON PINS 4+2 | 14-09-04 |
|
|
| Mitsubishi | CT2553 | Ghosting or ringing. | Drys around the SAW filter or coils L4/5 , if not mod kit AFT1 mits | 14-09-04 |
| Mitsubishi | CT2553 | Int blank raster. | Drys around the SAW filter or coils L4/5 , if not mod kit AFT1 mits | 14-09-04 |
| Mitsubishi | CT2553STX | INT LUMINANCE | CHECK FOR HARDENED GLUE on decoder print side | 14-09-04 |
| Mitsubishi | CT2553STX | WONT START , NO STBY LED , STBY PIN MICRO GOES LOW , | MEM IC FAULTY | 14-09-04 |
| Mitsubishi | CT2553STX Euro 4Z | HT voltage | Should be 156v | 14-09-04 |
| Mitsubishi | CT2553STX CT255 | Can not select Text : when cold will go into Text | Replace C922 & C923 ( 100uF ) | 14-09-04 |
| Mitsubishi | CT2554TX | DEAD | REPLACE Z902 | 14-09-04 |
| Mitsubishi | CT2554TX | Dead | Z902 PRF630 o/c near 5v reg | 14-09-04 |
| Mitsubishi | CT2555 | Ghosting or ringing. | Drys around the SAW filter or coils L4/5 , if not mod kit AFT1 mits | 14-09-04 |
| Mitsubishi | CT2555STx | Int sound & pic at sw on | C923 100µ 10v in psu | 14-09-04 |
| Mitsubishi | CT2555STX | No lum | No 12v to Q253 as print o/c top edge of dec pcb | 14-09-04 |
| Mitsubishi | CT2555STX | No lum - Txt & contrast ok | R286 100R o/c pin 11 IC602 | 14-09-04 |
| Mitsubishi | CT2555STX | NO LUMINANCE | R286 O/C 100OHM | 14-09-04 |
| Mitsubishi | CT2555STX | PICTURE WOBBLE / LINE TEARING TYPE FAULT | CHECK FOR DRY JOINTS AT LOPT SCREEN WHERE IT CONNECTS TO PRINT | 14-09-04 |
| Mitsubishi | CT2555STX | Very weak luma with flaring. | Clean glue off luma /chroma board & reconnect gap left in tracks. | 14-09-04 |
| Mitsubishi | CT2555TX | Wavy lines at sw on - clear when heated | C920 470µ 25v in reg stage next to large heatsink | 14-09-04 |
| Mitsubishi | CT25A2STX | COLOUR SUB-CAIER OFF SPEED | C604 OPEN | 14-09-04 |
| Mitsubishi | CT25A2STX | Cuts off totally 5 secs aft switch on keep pressi | Measure H.T if rises up to 180V then back to 145V replace C906 ( 47uF ) | 14-09-04 |
| Mitsubishi | CT25A2STX | Cuts out at sw on - HT high at 180v (145v) - will come on eventually | C906 47µ 63v in base Q901 (overvolts prot) | 14-09-04 |
| Mitsubishi | CT25A2STX | Dead - Q901 s/c. | Fit mod kit ( wVe 77901 ) R901 , D908 , Q901 , C908 to 2700pf , C966. | 14-09-04 |