| Make | Model | Problem | Solution | Date |
| | | |
| Found: 561
|
| Mitsubishi | CT28AV1BD | NOT HOLDING M1 SETTINGS | FIT 8V REGULATOR KIT | 14-09-04 |
| Mitsubishi | CT28AV1BD | Popping sound | Changed CRT base pcb | 14-09-04 |
| Mitsubishi | CT28AV1BSD | Dead | C955 3300µ 16v & reprog EEPROM | 14-09-04 |
| Mitsubishi | CT28AV1S | Dead - no st/by | LOPTx faulty - HR8204 is a replacement | 14-09-04 |
| Mitsubishi | CT28AV1S | No sound after ext spkrs connected | Check 4 x TDA7263 o/p chips (1 partly hidden) & safety res on audio panel | 14-09-04 |
| Mitsubishi | CT28B2STX | N/S Distortion | Replace Q4009 on PCC board. (TIP42C Substitute ok) | 14-09-04 |
| Mitsubishi | CT28BW2B | BRIGHT RASTER WITH FLYBACK LINES SET ARCING | REPLACE C551 AND R686 (CRT BASE) | 14-09-04 |
| Mitsubishi | CT28BW2B | MUFFLED SOUND FROM MAIN SPEAKERS DOLBY TEST PRODUCES NO SOUND FROM FRONT SPEAKERS | REPLACE IC351 | 14-09-04 |
| Mitsubishi | CT28BW2B | Muffled sound from main spkrs - no prologic sound o/p | IC351 audio o/p chip TDA7263 | 14-09-04 |
| Mitsubishi | CT28BW2B | Poor pics with streaking on whites | R686 1k8 hi res in G1 supply | 14-09-04 |
|
|
| Mitsubishi | CT28BW2B | Small Bright raster with fb lines - arcing from set | C551 3nF arcing - blew R686 - uprate to 2k7 on CRT base | 14-09-04 |
| Mitsubishi | CT28BW2B | Smearing on whites - OSD gives faulty crt symptom | R686 1k8 pin 5 crt base - change to 2k7 & set G2 to 00 in set up menu | 14-09-04 |
| MITSUBISHI | CT28BW2B | SMEARING ON WHITES LOOKS LIKE SOFT CRT | REPLACE R686 ON CRT BASE 1.8K OHM | 14-09-04 |
| Mitsubishi | CT28BW2BD | Lum int | Dry joint 8v reg Q952 (On same heatsink as IC401 7 pin LT reg) | 14-09-04 |
| Mitsubishi | CT28BW2BD | No sound | LT reg's were dry jointed causing intermittent loss of picture and sound, and I am sure this is what corrupted the eeprom. The Chassis is an EE3W and to access the service menu you need to press this sequence. "Menu,2,3,5,7". the adjustments are made in the same way as the EE3. | 14-09-04 |
| Mitsubishi | CT28BW2BD | Reverts to st/by at sw on | D507 BYD33G s/c in 28v supply to FOP | 14-09-04 |
| Mitsubishi | CT2964STX | Dead with psu blown | Check C909 (47uF 50V), C920 (470uF 25V), C923 (100uF 10V), C4009, (47uF 25V), IC4000 (TL082CP), D4000 (1N4148 s/c), Q4005 (BC337 C-E s/c), (D4006 8.2v zener) | 14-09-04 |
| Mitsubishi | CT2965 | Ghosting or ringing. | Drys around the SAW filter or coils L4/5 , if not mod kit AFT1 mits | 14-09-04 |
| Mitsubishi | CT2965 | Int blank raster. | Drys around the SAW filter or coils L4/5 , if not mod kit AFT1 mits | 14-09-04 |
| Mitsubishi | CT2965 | Set buzzing - Blown line transistor. | Q901 kit+IC901 , TEA2165 ( was 2164 ) , Z950 res , C906/956 , R950 , Dis L951 60w to deck if lit PSU ok | 14-09-04 |
| Mitsubishi | CT2965 ( STX ) | Dead - Q901 s/c. | Fit mod kit ( wVe 77901 ) R901 , D909 , Q901 , C908 to 2700pf , C969. | 14-09-04 |
| Mitsubishi | CT29655TX | The standby light was on and flickering , but apart | is in the primary. C905 ( 220uF , 25V ) . | 14-09-04 |
| Mitsubishi | CT2965STX | Chirping noise in st/by | Check C912 4.7uF, C906 47uF, C959 100uF, C905 220µ & check for dry joints | 14-09-04 |
| Mitsubishi | CT2965STX | DEAD FUSE Z950 OC SOC3150 | REPLACE WITH PRF5000 Pt No 299P132010 | 14-09-04 |
| Mitsubishi | CT2965STX | Dead. | CP Z950 ( SOC3150 ) now PRF5000 Part No. 299P132010. | 14-09-04 |
| Mitsubishi | CT2965STX | NO SOUND OR PICTURE - IC901 INT SC AND R901 OC. | IF Q901 SC CHECK D909 ( OUT OF CCT ) | 14-09-04 |
| Mitsubishi | CT2965STX | Tripping & LED flashes for 1st 15 mins b4 TV comes on | C905 220µ low cap - next to PSU IC | 14-09-04 |
| Mitsubishi | CT29A4STX | Hum from 1 speaker in st/by only | Q954 2SB1135 | 14-09-04 |
| Mitsubishi | CT29A4STX | NO SOUND | CHECK PROGRAMMING , THEN try Text if not working MAY BE MAB8461 ON TEXT BOARD. | 14-09-04 |
| Mitsubishi | CT29A4STX | No sound | 1000µ 35v cap in psu had leaked over print & damaged earth return | 14-09-04 |