| Make | Model | Problem | Solution | Date |
| | | |
| Found: 315
|
| Sanyo | CBP2576A ED0 chassis | Height twitches, int bright raster with fb lines | Resolder conns on digital panel | 14-09-04 |
| Sanyo | CBP2576A ED0 chassis | No raster | TEA5101A RGB chip | 14-09-04 |
| Sanyo | CBP2576A/00 | Bright blue raster with fb lines | IC500 which is a TEA5101A on the crt base pcb. R534 22 ohm was ok. | 14-09-04 |
| Sanyo | CBP2580 | Int start up - EHT can be heard | Check for int mains switch | 14-09-04 |
| Sanyo | CBP2580 | St/by only - trips at start up | 22mfd 250v B+ decoupler s/c | 14-09-04 |
| Sanyo | CBP2580 EB1 | AFTER 2-3 Hrs COLOUR GOES AND PICTURE SHIFTS TO R | XTAL X403 DRIFTING Pt No 610 217 1037 | 14-09-04 |
| Sanyo | CBP2580 EB1 | Colour lost & pic shifted to right when heated | Xtal X403 pt no 610 217 1037 | 14-09-04 |
| Sanyo | CBP2580 EB1 | Shuts down int - runs ok in service mode if IM bus run is stopped | Fault somewhere on the IM bus - NVM3060 EEPROM on digiboard cured fault | 14-09-04 |
| Sanyo | CBP2580 EB1 | To enter service mode | Menu on set's control panel, followed by menu on R/C handset | 14-09-04 |
| Sanyo | CBP2580 EB125 | This set would shut down interrnittently: the peri | The set could be made to run indefinitely by entering the service mode ( menu on the set's control panel , followed by menu on | 14-09-04 |
|
|
| Sanyo | CBP2580A EB2 series | Tripping - even with psu on dummy load | black jumper wire which runs from the earth side of the chopper transformer to a point very close to IC351 a regulator IC, was dry jointed at the chopper transformer end. | 14-09-04 |
| Sanyo | CBP2865 | INT BRIGHT RASTER WITH REDUCED HEIGHT | REPLACE IC780 12V REGULATOR | 14-09-04 |
| Sanyo | CBP2865 E3 | Int sound/pic with bright white raster with low height or field collapse reverting to st/by | IC780 SI3122V 12v reg s/c internally when heated | 14-09-04 |
| Sanyo | CBP2865 E3A28 | Picture and sound goes off int. | 12v Reg IC780 failed when hot. | 14-09-04 |
| Sanyo | CBP2866 | Int trip/blank raster/no field sync | IC780 12v reg - use TIP41 & 13v zener & 27v dropper as reg nla | 14-09-04 |
| Sanyo | CBP2872 | No sound from spkrs - ok from scart | IC561 APU2471 on sigs panel | 14-09-04 |
| Sanyo | CBP2872 | REPEAT FAIL OF LOP TR ( 2SD1555 ) | IC DPU2553 | 14-09-04 |
| Sanyo | CBP2872 ED1 | Lines when cold with shading as warms up | C404 (100mfd 50v) in the frame stage was the culprit, although its ESR reading was OK, and there were no signs of leakage | 14-09-04 |
| Sanyo | CBP2872 ED1 | No sound - comes on briefly when cold sometimes with crackle/hiss | OK from scart socket - IC561 APU2471 could be faulty | 14-09-04 |
| Sanyo | CBP2872 ED1 | No sound when sw on if still warm | IC560 ADC2301E on sigs panel pt no 409 211 9404 | 14-09-04 |
| Sanyo | CBP2876 | Red, green & blue flyback lines | C700 100µ hi esr | 14-09-04 |
| Sanyo | CBP2876 | St/by only with squealing | fop chip TDA8170, C703 100µ, Fuselink R715 replaced & now works with hissing from LOPTx. LOPTx also replaced | 14-09-04 |
| Sanyo | CBP2876 ED series | Dead - LOPTr s/c | dry joints on the Q600 a TIP111
Darlington device, C606 2.2mfd 50 volts C605 located next to TIP111 which was leaking electrolyte, T600 the line driver TX which was short circuit to all legs having cooked up and R600 10 safety resistor which feeds the line drive stage from the 28 volts rail coming from the PSU. | 14-09-04 |
| Sanyo | CBP2876 ED0 series | Field collapse with thin bowed line across screen | Bad joints CRT coil connector | 14-09-04 |
| Sanyo | CBP2876-00 ED028 | Txt moves sideways - pic ok | IC400 DPU2553 & check for line pulses to the chip | 14-09-04 |
| Sanyo | CBP3001 | Lines over pic & bent verts | C421 1000µ faulty - decoupler for IC201 supply pin 6 | 14-09-04 |
| Sanyo | CBP3011 | St/by only | Pin 21 of main micro had a 48R leak to 5v rail - micro faulty | 14-09-04 |
| Sanyo | CBP3011 - 15 | Dead | R320 , 321 120k | 14-09-04 |
| Sanyo | CBP3011-15 | Dead | R320 & 321 120k hi res | 14-09-04 |
| Sanyo | CBP3011-15 | Dead. | R320/21 ( 120k ) changed value. *WARNING smoothing cap charged* | 14-09-04 |