| Make | Model | Problem | Solution | Date |
| | | |
| Found: 711
|
| Sharp | CA10 59DS03H | Dead apart from power light | 2 x 560k start up res hidden under chopper heatsink | 14-09-04 |
| Sharp | CA10 59DS03H | Dead with mains fuse o/c | Q701 chopper FET s/c RH-TX0166BM22, D712 zener RH-EX0419BM22, BUH515 LOPTr - if stuck in st/by aft replacement Q702 BC338 in psu s/c | 14-09-04 |
| Sharp | CA10 59DS03H | Field - no pic at top ? of raster | Field stage is supplied with + & -ve supplies fused by F601/2. Check these & Q501/2. Q501 faulty & replaced with a IRFI9020 (uprated device) | 14-09-04 |
| Sharp | CA10 59DS03H | Field scan at top stretched | Scan coils faulty - do not run for long - risk of crt neck damage | 14-09-04 |
| Sharp | CA10 59DS03H | FRAME COLLAPSE | REPLACE F602 | 14-09-04 |
| Sharp | CA10 59DS03H | NO REMOTE OR KEYPAD FUNCTIONS | REPLACE R705 68K | 14-09-04 |
| Sharp | CA10 59DS03H | PARTIAL FRAME COLLAPSE | REPLACE F0601 F0602 AT REAR OF PCB | 14-09-04 |
| Sharp | CA10 59DS03H | St/by only | 2 x 560k start up res o/c (hidden by chopper tr heatsink) | 14-09-04 |
| Sharp | CA10 59DS05H | Dead | Dry joints C613, lop tr s/c & R613 2k2 hi res | 14-09-04 |
| Sharp | CA10 59DS05H | No pic - L604 overheating | C613 68nF 250v, C619 2µ2 160v, & R613 2k2 2w. Also check Q602 BUH515 | 14-09-04 |
|
|
| Sharp | CA10 59DS05H | No sound & only bottom half of raster | R530 1R fusible o/c; sm cap 0.1µ (estimate) connected between D516 & chassis leaky | 14-09-04 |
| Sharp | CA10 59DS05H | PSU cuts out as pic appears | Check R721 100k, R704 68k, R705 68k, R703 100k | 14-09-04 |
| Sharp | CA10 66DS03H | BOTTOM HALF OF PICTURE OK TOP IS LINES WITH E/W DIST | REPLACE F601 NEAR LOPTX | 14-09-04 |
| Sharp | CA10 66DS03H | Dead | Dry joint & o/c C613 680n & res across it o/c- to rt of Loptx | 14-09-04 |
| Sharp | CA10 66DS03H | Dead - LOPTr Q602 BUH515 s/c | C604 | 14-09-04 |
| Sharp | CA10 66DS03H | Dead with whine from psu | Dry joints C613 680n - replace cap & resistor across it | 14-09-04 |
| Sharp | CA10 66DS03H | Field - bottom ok top squashed with lines | F601 N27 2.5A fuse | 14-09-04 |
| Sharp | CA10 66DS03H | No control via front or remote | R705 68k st/by 5v feed | 14-09-04 |
| Sharp | CA10 66DS03H | NO REMOTE OR FRONT FUNCTIONS | CHECK R704/705 FOR O/C OR HIGH VALUE SHOULD BE 68K | 14-09-04 |
| Sharp | CA10 66DS03H | St/by only | LOPTr s/c due to almost invisible dry joints on scan coil conn | 14-09-04 |
| Sharp | CA10 66DS03H | STUCK ON 1 CHANNEL, NO REMOTE OR FRONT FUNCTIONS | REPLACE R705 68K | 14-09-04 |
| Sharp | CA10 66DS05H | Field lin problems | Check F601/2 o/c | 14-09-04 |
| Sharp | CA10 66DS05H | INTERMITTENT STANDBY AT HIGH VOLUME | CHANGE VALUE OF C335/C336 TO 022MFD | 14-09-04 |
| Sharp | CA10 66DS05H | St/by only | BUH515 lop tr s/c due to dry joint C613 0µ68 250v | 14-09-04 |
| Sharp | CA10 66DS05H | St/by only - shuts down aft 2 secs | Check spkr is connected & ok (will not run if dis'd) | 14-09-04 |
| Sharp | CA10 66ES03H | Dead | R713 (and/or) R714 in PSU o/c. (Both 560K) | 14-09-04 |
| Sharp | CA10 66ES03H | Dead | Dry joint C613 680nF 250v &/or o/c, LOPTr s/c or overheating, R613 2k2 2w o/c pt no VRS-VV3DB222J | 14-09-04 |
| Sharp | CA10 66ES03H | Dead - blow up after dry joint on C613 | Q701 2SK2605; Q702 BC338; Q703 BC338; Q602 BUH515 line o/p tr; D712 BZX79C15; D713 1N4148; R716 .R.47 1 WATT CIRCUIT SAYS R.22 BUT THE ORIGINAL WAS R.47; R717 22K; R719 22O OHM; C713 68 NFD.; FUSE 3.15a | 14-09-04 |
| Sharp | CA10 66ES03H | Dead - blows Q701 Q702 Q703 D712 D715 at switch on | Change Q701 BUZ90, Q702 & Q703 BC338, R722 33R smr.R716, R61, D715 & D712. I/C 901 TDA6107 on tube base. D712 15volt zener not marked as zener on print. | 14-09-04 |
| Sharp | CA10 66ES03H | Dead - chopper Tr s/c | Replaced along with 2 x mains rects, R716 0R22, Q702 & Q703 + dry joints LOP | 14-09-04 |