| Make | Model | Problem | Solution | Date |
| | | |
| Found: 749
|
| Goodmans | 285NS Daewoo GB2898ST | Buzz on sound at low level | resolder fop chip heatsink | 14-09-04 |
| Goodmans | 285NS(B) | DARK PICTURE WHEN USING SUBTITLES | SELECT TEXT THEN PRESS MENU AND ADJUST BRIGHTNESS LEVEL | 14-09-04 |
| Goodmans | 285NS(B) | No red | TDA6106Q s/c & R916 100R 1/2w burnt | 14-09-04 |
| Goodmans | 285NSB | Blank raster when cold - appears over time - sound ok | Feedback signal to Jungle chip dist (no SCL pulse) - TDA8351 faulty | 14-09-04 |
| Goodmans | 285NSB | Dark pic when using Txt subtitles | Txt brightness set low - select Txt then Menu to access Txt menu | 14-09-04 |
| Goodmans | 285NSB | Dead - mains fuse blown | Positor faulty - rattled & pic shifted to left until replaced | 14-09-04 |
| Goodmans | 285NSB | Grey scale varies | I901, 2 & 3 Ics on crt base - change all 3 | 14-09-04 |
| Goodmans | 285NSB | St/by only | No line Dr from TDA8375A - s/c pin 24 IC602 - faulty chip | 14-09-04 |
| Goodmans | 286N5/05 | Service Mode access | call up the main menu then press 2,3,5,7, quite quickly on the remote. To get to geometry settings press * (star).if the EEprom is relaced with a blank one, as supplied by SEME, the picture geometry settings have to be adjusted for each different "display" setting (aspect ratio) | 14-09-04 |
| Goodmans | 286N5/05 | Tries to start up then trips | Tr75055 BC337 | 14-09-04 |
|
|
| Goodmans | 286NS | DEAD NO POWER LED | REPLACE C2915 | 14-09-04 |
| Goodmans | 286NS | Field foldover | Check R3908 (2.2ohm), R3923 (560ohm) both on frame panel | 14-09-04 |
| Goodmans | 286NS | FRAME COLLAPSE | R3908 O/C 2R2 | 14-09-04 |
| Goodmans | 286NS | PARTIAL FRAME COLLAPSE | REPLACE R3988 2.2OHM FUSABLE | 14-09-04 |
| Goodmans | 286NS | STUCK ON STANDBY | REPLACE FUSABLE 1502 BESIDE SMPS TRANSFORMER POSSIBLE ICFN25 | 14-09-04 |
| Goodmans | 286NS (Philips L6.3 chassis) | No sound - noise only from speakers | MPS3410 chip faulty - replaced audio pcb | 14-09-04 |
| Goodmans | 286NS L6.2 | Pic break up with sound muted | LOP stage volts down 10 volts at 140V. R3509 47K in PSU O/C. | 14-09-04 |
| Goodmans | 286NS L6.2 | Pic shifted to left; RV3120 no effect - Txt OK | Crack in print to RV120 | 14-09-04 |
| Goodmans | 286NS L6.3 | Blows BU1508AX | Loptx faulty pt no 482214010623 | 14-09-04 |
| Goodmans | 286NS L6.3 | Comes on then pic disappears into snow, sound ok then sw itself off etc | Replace 7505 BC337/40 & 7500 BC858B(situated on print side by 7505) also replaced 22uf 2511. | 14-09-04 |
| Goodmans | 286NS L6.3 | Dead - buzzing | L4520 gone hi pt no 482215750965, T7906 BU1508AX s/c | 14-09-04 |
| Goodmans | 286NS L6.3 | Dead - no LED | C2915 390nF 250v | 14-09-04 |
| Goodmans | 286NS L6.3 | E-W faulty | Replaced C2913 & C2915 | 14-09-04 |
| Goodmans | 286NS L6.3 | Ext 1 or 2 can't be selected using "0" button | 24C02AB1 EEPROM | 14-09-04 |
| Goodmans | 286NS L6.3 | Field collapse | R3908 2R2 0.33w o/c | 14-09-04 |
| Goodmans | 286NS L6.3 | Field partial collapse | R3988 2R2 fusible o/c | 14-09-04 |
| Goodmans | 286NS L6.3 | Int comes on at sw on | R3512 68k, R3513 330k, R3518 120k start up res | 14-09-04 |
| Goodmans | 286NS L6.3 | Lack of width, line speed off, no field sync | IC7100 TDA8361 | 14-09-04 |
| Goodmans | 286NS L6.3 | Line collapse | C2915 390nF o/c, R3929 220R & R3930 560R burnt | 14-09-04 |
| Goodmans | 286NS L6.3 | St/by only | Fusible 1502 o/c, when replaced Field collapse - crack in print to 7422 opto coupler | 14-09-04 |