| Make | Model | Problem | Solution | Date |
| | | |
| Found: 749
|
| Goodmans | FST51T/T | int sigs / patterning | dy joints tuner; adl L700 for patt | 14-09-04 |
| Goodmans | FST51TT | White raster with fb lines | 100mA fuse & 220R R115 190v supply to RGB chip IC100 o/c - replace chip and supply comps | 14-09-04 |
| Goodmans | GD25 | PATTERNING , ESP WITH WEAK SIG , CHANNELS 24 , 28 , 31 | REPLACE AERIAL LEAD WITH QUALITY LEAD , TOSHIBA HAVE PART AVAIL. Pt No 70011442 | 14-09-04 |
| Goodmans | GD2580 | Loud whistle | LL26 coil in line stage - hot melt glue used | 14-09-04 |
| Goodmans | GD2580 TX92 | E/W settings different at sw on & int reverts to st/by | IF02 STV2145 | 14-09-04 |
| Goodmans | GD2580 TX92 | Int dead | dry joints CP13 1nF5 1.6kv | 14-09-04 |
| Goodmans | GD2580B TX92 | Installation menu entering | Sw TV to st/by then sw off at mains. Sw on TV whilst holding "P" button in on front until Lang menu appears | 14-09-04 |
| Goodmans | GD2592 | Dead with blackened mains fuse | Chopper FETTr TP16 s/c, dry joints CP13 & DP51 BY399 HT rect s/c | 14-09-04 |
| Goodmans | GD2880 | Dead | RL12 o/c | 14-09-04 |
| Goodmans | GD2880 | Dead | Dry joint CP13 1n5 by chopper tr | 14-09-04 |
|
|
| Goodmans | GD2880 | Int pic blanking & no sound | Pi 9 IX01 volts varying - TX15 BC848B sm | 14-09-04 |
| Goodmans | GD2880 | Poor pic with ghosting | Dry joints IF | 14-09-04 |
| Goodmans | GD2880A ICC9 | Blank raster - ok via scart | TX16 BC858B in scart sect faulty | 14-09-04 |
| Goodmans | GD2880A ICC9 | Crackling on NICAM | Possible changing TDA8732 & 13.104Mhz filter 1N01 pt no 1025398000 together will cure | 14-09-04 |
| Goodmans | GD2880A ICC9 | Int dead | Volts around TR85 BC848B & TR87 BC858B incorrect - Trs faulty | 14-09-04 |
| Goodmans | GD2880A ICC9 | St/by only | TP66 BC858B sm | 14-09-04 |
| Goodmans | GD2880A ICC9 | TV works ok but LED red not Green | TR28 BC858B sm s/c | 14-09-04 |
| Goodmans | GD2880B | Ghosting/ringing pic which couldn't be fine-tuned | Tuner faulty | 14-09-04 |
| Goodmans | GD2880D | Switches off aft 5 mins | Change white opto coupler IP60 4N25TV for black type (same no) | 14-09-04 |
| Goodmans | GD2880D TX92F | Int reverts to st/by | Dry joints CP13 in snubber | 14-09-04 |
| Goodmans | GD2880D TX92F | Reverts to St/by aft init EHT rush & brief green LED | TL41 BD681 (s.c.), RL47 3.3 ohms, DL21 BY228 ( S.C.), 1.5uF 160V.W. capacitor (o.c.) | 14-09-04 |
| Goodmans | GTV20CTV | Dead | C125 100µ in 12v reg supply line | 14-09-04 |
| Goodmans | GTV211 | Field scan patially missing, no sigs | R26 12k in 30v supply rail | 14-09-04 |
| Goodmans | GTV211 | Short pic, no vid & green background | Check shorting links 1068/1169 (rear of proc) are not touching together | 14-09-04 |
| Goodmans | GTV288 | Dead | Chopper tfmr dry joints caused burn up - resoldered (11AK12-9 chassis) | 14-09-04 |
| Goodmans | GTV288 | Remote control wont work apart from bringing set out of st/by | MD501 on front control panel | 14-09-04 |
| Goodmans | GTV288 11AK19-8A | Poor contrast - poor sync - no colour -sound intermittent | TDA8843 | 14-09-04 |
| Goodmans | GTV288 11AK19 | Dead apart from flashing G LED at sw on | R867 0R33 1/2w o/c (not shown on all ccts) | 14-09-04 |
| Goodmans | GTV66W 1 11AK19 | Blank raster | small RGB panel on CRT pcb had broken print (not surprising as it gets a lot of physical strain) | 14-09-04 |
| Goodmans | GTV66W 1 11AK19 | Bright white raster at sw on then trips off | No volts to TDA6107Q RGB o/p chip on crt base as 47R safety res R914 on base o/c - dry joint on A1 conn of crt base & others probably caused it | 14-09-04 |