| Make | Model | Problem | Solution | Date |
| | | |
| Found: 749
|
| Goodmans | TX805 1410 | St/by only | DP50 150v zener - resolder link from Pin 5 to CP17 | 14-09-04 |
| Goodmans | TX805 1410 | Weak contrast, blank raster when A1 advanced | TC01 BC558B s/c | 14-09-04 |
| Goodmans | TX92 chassis | Hotel mode (no tuning menu) - to unlock | ) turn TV in to standby from remote
2) turn power off from mains on/off switch and wait until led goes off.
3)hold standby button on remote control and power up from on/of switch hold standbye button for about 10 seconds then de/active hotel lock. | 14-09-04 |
| Goodmans | TX92 GD2880B | Fishnet/herringbone patterning on certain chans | Fit good quality RF downlead/flylead | 14-09-04 |
| Goodmans | TX92 GD2880B | Impurities due to degaus triac not triggering | Change RP40 from 1R to 2R2, CP40 from 470µ 6v3 to 2200µ 16v | 14-09-04 |
| GOODMANS | VN6000 | DEAD | REPLACE C822 IN POWER SUPPLY 330MFD63V | 14-09-04 |
| Goodmans | VN6000 | Dead - orig int dead | C822 & 823 in psu low cap | 14-09-04 |
| Goodmans | W280NS | Dead - arcing LOPTx killed it | SEME type 1362.5001 code is LOPTX1324 ?27. The orig no. 1372.0066A | 14-09-04 |
| Goodmans | W280NS | Dead - repeatedly blows LOPTr | LOP tuning cap 15nF dry jointed | 14-09-04 |
| Goodmans | W280NS | Service mode entering | With TV off, press & hold middle button of 5 under flap. Press on off button whilst still holding button for
3 secs then press st/by on handset. Store with yellow button | 14-09-04 |
|
|
| Goodmans | W280NS | Tripping | Dry joints C68 & C71 & LOPTr slightly leaky | 14-09-04 |
| Goodmans | W280NS Formenti F19 | Service mode access | Sw on TV holding in Vol+. Release vol button & press St/by on r/c within 3 secs. To save settings press yellow "mem" button else press TV/AV to exit without saving changes | 14-09-04 |
| Goodmans | W282NS | Width lacking with foldover | D25 BA157 | 14-09-04 |
| Goodmans | W287 | Dead aft 5 mins | TP2 reg heatsink dry joint | 14-09-04 |
| Goodmans | W287NS | Trips to st/by | DL16 BYV95C near LOPTx s/c | 14-09-04 |
| Goodmans | W288 F19 | No video - sound ok | R34 12K & R35 47R O/C | 14-09-04 |
| Goodmans | W288NS | Reverts to st/by aft 10 mins | TR20 hot. May blow TR21. C147 470nf & TR20 BC639. | 14-09-04 |
| Goodmans | W288NS | Sound absent | J103 22R fusible o/c due to sm comp across 12v rail on Nicam board (across C49) - comp removed | 14-09-04 |
| Goodmans | W28NS F19 | Dead - went off with a crack | LOPTx has sooty deposit on top - fit replacement 1372.0052 FBT40828 CHS ?21.20 | 14-09-04 |
| Goodmans | W321NS | Dead - mains fuse blown | SM Tx o/c pri, IC14 TDA4601, LOPTr BU508DF | 14-09-04 |
| Goodmans | W321NS | HT low & EHT low at 20kv | D37 1N4148 leaky | 14-09-04 |
| Goodmans | W321NS | No sound | C123 1000µ, TR26 Darl was s/c (supply to Aud o/p chip IC8 TDA1521A - also s/c) | 14-09-04 |
| Goodmans | W321NS F16 | Line drive int | Glue under R217 4k7 becomes carbonised - clear glue | 14-09-04 |
| Goodmans | W322NS | Tripping - LOPTr s/c | Caused by 15nF 2kv flyback cap never being soldered | 14-09-04 |
| Goodmans | W322NS | The S-correction capacitor had blown, now replaced and all seems fine except for the e-w correction. Initially no difference between "Standard" and "Reduced" aspect ratio modes, but that's now effective after tweaking e-w correction to zero in service mod | Check D27 , L604 (15mH) , R82 and R83
| 18-08-05 |
| Goodmans | W322Ns F19 | Dead apart from tripping PSU | LOPTr s/c which blew when replaced - 15nF 2kv flyback tuning cap never been soldered in properly | 14-09-04 |
| Goodmans | W322Ns F19 | Dead with regular ticking from psu | Dry joints C68, 69 & 70, D24 BY288 s/c, C69 22nF low cap & BU508D faulty tho' checked ok | 14-09-04 |
| Goodmans | WS288NS | Dead with whistle from LOP | C134 & LOPTr | 14-09-04 |
| Goodmans | ZX | No frame. | R401 ( 1R ) o/c. | 14-09-04 |