| Make | Model | Problem | Solution | Date |
| | | |
| Found: 1771
|
| Ferguson | ICC5 | Blank bright raster. | 10R on CRT base. | 14-09-04 |
| Ferguson | ICC5 | Blank raster & no sound | TDA2541 | 14-09-04 |
| Ferguson | ICC5 | Blowing BU. | RL10 o/c may be intermittent | 14-09-04 |
| Ferguson | ICC5 | Bright white raster with fback lines | No volts coll of RGB o/p trs - RV82 10R safety res on crt base o/c | 14-09-04 |
| Ferguson | ICC5 | Channels - no channel change. | IC IR01. | 14-09-04 |
| Ferguson | ICC5 | Child lock - unlocking | press R,G,B & hold Y for 10sec. Now go to the menu, child lock, pin. When it asks for the OLD PIN, press again R,G,B & Y for 10 sec - you can set-up a NEW PIN. | 14-09-04 |
| Ferguson | ICC5 | Child lock removal | Press "Red" then "Green", then "blue", then hold "yellow" for 10 secs | 14-09-04 |
| Ferguson | ICC5 | CLICKING ON NICAM | FIT 47K BETWEEN PINS 13 & 16 IC1580 NICAM PCB | 14-09-04 |
| Ferguson | ICC5 | Col flickers on high contrast pics & width varies with pic content | CL41 (in parallel with DL41 in LOP stage). Value depends on the model
(15nF/20nF/26nF 400V). | 14-09-04 |
| Ferguson | ICC5 | Dead | Check LG11 ***must replace CL44 ( 33pF ) RL44 IG01 ( TDA4950 ) fit a ( 22ohm ) in place of JI34 | 14-09-04 |
|
|
| Ferguson | ICC5 | Dead | LOPTr s/c caused by dry joints LOPTx | 14-09-04 |
| Ferguson | ICC5 | Dead | LOPTx, Chopper tr BU508A, Field thy, jungle chip, fucus/A1 unit & elect caps | 14-09-04 |
| Ferguson | ICC5 | Dead - blowing fuse at switch on. | Check degauss PTC. | 14-09-04 |
| Ferguson | ICC5 | Dead - blows mains fuses | CP02 10nf blue dis cap s/c | 14-09-04 |
| Ferguson | ICC5 | DEAD , P.SUPP WONT START | TL17 BC548 . IF 300v COLL TP24 + S.BY LIGHT ON + LT TO IL14 NO OSC PIN 7 , IL14 US | 14-09-04 |
| Ferguson | ICC5 | Dead apart from rush of EHT | CP26 470µ - res cap for 7.5v supply | 14-09-04 |
| Ferguson | ICC5 | DEAD SHOWS 88 IN DISPLAY | RP42 1R OC IN POWER SUPPLY | 14-09-04 |
| Ferguson | ICC5 | Dead st/by led flickers once at sw on | LG11 e-w mod coil shorted turns; IG01 TDA4950 e-w chip s/c; CL44 0µ3 o/c; RL46 1k across line lin coil burnt; RL44 56R & 120R 1/4w o/c; J134 22R feed to TDA4950 o/c | 14-09-04 |
| Ferguson | ICC5 | E/W faulty - TDA4950 & assoc res u/s | E/W coilo - read only 0µH95 instead of 1µH7 | 14-09-04 |
| Ferguson | ICC5 | East west - Geometry problems. | Drys on pins of IG01. | 14-09-04 |
| Ferguson | ICC5 | E-W bowing | Replace DL42 (BA157) and 18k res across it | 14-09-04 |
| Ferguson | ICC5 | E-W bowing | Check CL44 0µ3 250v for bulge | 14-09-04 |
| Ferguson | ICC5 | FAILURE OF E/W LOADING COIL WITH 110 TUBES | REPLACE ALL PARTS LISTED , CL44 , 330nf , RL44 , 56+120ohm FUSIBLE , J134 22ohm FUSIBLE , IG01 TDA4950. ALSO CHECK CG11 Inf | 14-09-04 |
| Ferguson | ICC5 | faint pic sound ok | CV90, CP37 and check for dry joints | 14-09-04 |
| Ferguson | ICC5 | Field collapse (wavy line) | dry joints/ oc print to scan coil plug | 14-09-04 |
| Ferguson | ICC5 | Frame - intermittent frame collapse. | DP47 int o/c. | 14-09-04 |
| Ferguson | ICC5 | Frame collapse. | Check 3M RL33 , at pin 9 of IL14 for o/c. | 14-09-04 |
| Ferguson | ICC5 | Frame collapse. | 3MR at RF01 on main PCB gos high. | 14-09-04 |
| Ferguson | ICC5 | Frame collapse. | RF01 ( 3M ) o/c. | 14-09-04 |
| Ferguson | ICC5 | Frame foldover at top of picture. | RF ( 1k ) high at 3k. | 14-09-04 |