| Make | Model | Problem | Solution | Date |
| | | |
| Found: 1771
|
| Ferguson | TX92 T59F | Unable to tune higher freqs | IR01 ST9291JB1 | 14-09-04 |
| Ferguson | TX92 T59F | NT varies | Check TP48 (BC855B SMD in PSU) | 14-09-04 |
| Ferguson | TX92 T59N | Tuner int symptom | Can be caused by sm trs in IF unit - blanket resolder | 14-09-04 |
| Ferguson | TX92 T59NB | Dead - LED flashing - HT (130v) down to 60v | LOPTx | 14-09-04 |
| Ferguson | TX92 T59NB | Flashing LED - rasping noise when comes out of st/by only | LOPTx - make sure you quote exact pt no off orig | 14-09-04 |
| Ferguson | TX92 T68N | Dead with LED flashing | LOPTx suspect (2 different types) - replacement often leaves same fault symptoms - if RL08 10k sm has burnt out, safety cct damaged - check DL08, DL80 & 81 (LL4148), TL80BC548 & DL83 24v. May also damage micro &/or EEPROM | 14-09-04 |
| Ferguson | TX92 T68NB | St/by only | Mains sw - CHS 20102AG | 14-09-04 |
| Ferguson | TX92 T78N | Dead with st/by led flashing | Check LOPTx & EEPROM X24C04 IR01 - damaged when fault occurred (if fault still present) | 14-09-04 |
| Ferguson | TX92F | Dead | RP08 270k ?w o/c | 14-09-04 |
| Ferguson | TX92F | Switches off aft 5 mins | Change white opto coupler IP60 4N25TV for black type (same no) | 14-09-04 |
|
|
| Ferguson | TX92F T59NB | Dead sm resistors burnt up under LOPTx | RL07 3k9 & RLo8 10k sm under Loptx & replace LOPTx that caused the fault | 14-09-04 |
| Ferguson | TX92F T59NB | Field foldover at top | CF30 47µ 50v between pins 3 & 6 of FOP chip IF01 | 14-09-04 |
| Ferguson | TX92F T59NB | St/by only with flashing led | LOPTx & RL08 10k sm under loptX | 14-09-04 |
| Ferguson | TX98 | Blank screen, sound ok | Tr7 BC372S u/s tho read ok | 14-09-04 |
| Ferguson | TX98 | CHANGES CHANNEL BY ITSELF TURNS VOL UP ETC. | CUT PRINT PIN 11 INFRA RED AMP IC904 add ( 0.1uF ) ACROSS CUT | 14-09-04 |
| Ferguson | TX98 | colour varies & int lines | dry joint focus/A1 earth pin 4 of lopt | 14-09-04 |
| Ferguson | TX98 | CRT - mod if changing to Philips A51EAM31X01. | See Feedback 51 1991 + Mod sheet with kit 00X6714001 | 14-09-04 |
| Ferguson | TX98 | D17 blown. | Check Degauss NTC/PTC ( Z2 ) , Chopper Tx & IC , Bridge Rec , y | 14-09-04 |
| Ferguson | TX98 | Dead | o/c prot in 17v feed to TDA8138 | 14-09-04 |
| Ferguson | TX98 | Dead - HT present at LOP tr | ICP1 N25 cct prot for 17v o/c (next to chopper tfmr) | 14-09-04 |
| Ferguson | TX98 | Dead - no 5v at pin 9 of TDA8138. | IC TDA8138. | 14-09-04 |
| Ferguson | TX98 | Dead 1.25A fuse blackened | Chopper tr s/c due to arcing mains sw | 14-09-04 |
| Ferguson | TX98 | DEAD 17v ON IC11 NO 5v ( PIN 9 ) NO 12v ( PIN 8 ) | IC11 TDA8138 US | 14-09-04 |
| Ferguson | TX98 | dead mains fuse shattered | Tr3 s/c, C88 100µ o/c | 14-09-04 |
| Ferguson | TX98 | Incorect on-screen graphics. | Dry on link 47. | 14-09-04 |
| Ferguson | TX98 | Incorect remote operation. | Switch set off then back on again. | 14-09-04 |
| Ferguson | TX98 | int line foldover when warm | dry joints L26 & 27 | 14-09-04 |
| Ferguson | TX98 | LOPTx arcing to heatsink | Replace LOPTx & C113 7n5, R222 0R68 | 14-09-04 |
| Ferguson | TX98 | Mod if changing tube to Philips A51EAM31X01 | Mod see Feedback 51 1991. | 14-09-04 |
| Ferguson | TX98 | No col & lack of height | IC11 TDA8138 | 14-09-04 |