| Make | Model | Problem | Solution | Date |
| | | |
| Found: 1771
|
| Ferguson | ICC7 | Field collapse | Check for cracks in print between pin 5 IF01 & pin 2 BF01 Scan coil plug | 14-09-04 |
| Ferguson | ICC7 | Field collapse | DF16 BA157 | 14-09-04 |
| Ferguson | ICC7 | Field collapse Screen blanked out May go into StBy | Check RV72 ( 22ohm ) RL11 ( 15ohm ) RF07 ( 1M5ohm ) DF16 ( BA1257 ) DL11 ( BA157 ) | 14-09-04 |
| Ferguson | ICC7 | FIELD FOLDOVER | USUALLY AFTER TDA8178F FIELD IC IC CHANGED THIS IS MARKED AS A LINK J238 AND NOT SHOWN IN MANUAL. PT No. Ferguson 41081600 | 14-09-04 |
| Ferguson | ICC7 | Field foldover : Reduced scan | RF23 o/c Print o/c at pin 12 LOPT RF07 ( 1M5ohm ) RF21 ( 0.68ohm ) DL09 ( BA157 ) DF17 s/c | 14-09-04 |
| Ferguson | ICC7 | Field foldover at bottom | CF84 1µ (in front of field coils plug) | 14-09-04 |
| Ferguson | ICC7 | Field IC replacement | Replaced by STV9379F & 3k9 between pins 2 & 7, 2v1 zener between pin7(+) & (-ve) to chassis (IC MUST have suffix "F") - If not you get lack of height & blows line dr tr & RP52 safety res | 14-09-04 |
| Ferguson | ICC7 | int black & white lines | dry joints esp CS25 1µ in IF module | 14-09-04 |
| Ferguson | ICC7 | Int dead | triggers over current sensor - HT setting critical (120v) | 14-09-04 |
| Ferguson | ICC7 | Int going into standby. | CHECK TR16 - TR17. Check pin 40 IV01 , 9V= on 0V = StBy Trip | 14-09-04 |
|
|
| Ferguson | ICC7 | Int sound - comes & goes when flexing Nicam pcb | replace all links on Nicam pcb | 14-09-04 |
| Ferguson | ICC7 | Lack of width with IG01 overheating | Replace IG01 & CL24 440nf o/c - which was the cause of the fault | 14-09-04 |
| Ferguson | ICC7 | LINE DRIVER GOES SC AFTER 10secs TL17 | DF16 IN FIELD CCT SC | 14-09-04 |
| Ferguson | ICC7 | LINE OP TRANSISTOR SC REPLACEMENT BLOWS AFTER 15min | LINE DRIVE TX DRY | 14-09-04 |
| Ferguson | ICC7 | Lines on screen looks like IF off , usually when 1 | D/J on CS25 ( 1uF ) inside if can pin 13 IS10 | 14-09-04 |
| Ferguson | ICC7 | LOP TRANSISTOR SC - BLOWS AFTER 15mins | LINE DRIVE TX DRY | 14-09-04 |
| Ferguson | ICC7 | LOW RED/GREEN ETC | CHECK 39Ks CRT BASE | 14-09-04 |
| Ferguson | ICC7 | Low sound | C514 1µ 63v in if can | 14-09-04 |
| Ferguson | ICC7 | NO NS CORRECTION | CHECK FOR -26.8v AT EMITTER OF TG38 OR TG84 BD137 : if missing RG87 ( 2.2ohm ) o/c or TG84 leaky | 14-09-04 |
| Ferguson | ICC7 | No colour | Check RC09 ( 22ohm ) 12V feed to pin 6 IV01 ( D/J on BE06 Text PCB ) | 14-09-04 |
| Ferguson | ICC7 | No colour | IV01 ( TA8659 ) IE50 ( TEA2114 ) | 14-09-04 |
| Ferguson | ICC7 | No EW correction. | RG87 ( 2.2R ) o/c , TG84 s/c or leaky on NS PCB right hand side | 14-09-04 |
| Ferguson | ICC7 | No field or line sync | CV54 0µ1 o/c | 14-09-04 |
| Ferguson | ICC7 | No frame. | RL11 ( 15R ) o/c , and/or DL11 ( BA157 ) s/c , TDA8178F | 14-09-04 |
| Ferguson | ICC7 | No go - line transistor short. | Check for drys on line driver Tx. | 14-09-04 |
| Ferguson | ICC7 | No N/S corr | TG84 BD137; RG87 2R2 | 14-09-04 |
| Ferguson | ICC7 | NO NICAM SOUND | R501 ( 33R ) -ON NICAM PCB | 14-09-04 |
| Ferguson | ICC7 | no r/c operation | BA01 dry joint | 14-09-04 |
| Ferguson | ICC7 | No sound or pic X Hatch type patt only | Tapping IF module affected fault - dry joints IF unit | 14-09-04 |
| Ferguson | ICC7 | No sound/vision - no vid at IF module pin 6 | Sound visible at pin 10 of module - module u/s - repaired at MCES | 14-09-04 |