| Make | Model | Problem | Solution | Date |
| | | |
| Found: 4551
|
| Philips | 14PV162 | Spare part information | If the lever inside the mains-switch is broken, the switch doesn't remain in the "ON" position.
Solution: replace the switch by a new one. Improved switches of a newer production range are on stock. (4822 276 13542) | 14-09-04 |
| Philips | 14PV162 | Start up problems | When the set is switched on by the mains-switch while a cassette is in the set, the front LED starts blinking, but the set doesn't start.
Solution:
Check the primary voltage (Ubat) and adjust this for 14" sets to exactly 101.5 Volt. (See chapter 3.1.1 | 14-09-04 |
| Philips | 14PV162 | Tuner modification | An early production problem appears on these sets: the AGC voltage supplied to the Tuner 1 is too high (app. 8.8V) in comparison to the supply voltage (5V). It results in a wrong correction of the AGC loop when the antenna's signal is too low (about 1,5mV | 14-09-04 |
| Philips | 14PV162/01 | Codenumber information | A new software version (PTCP2-7) is available for the control uP (IC 7801). Service codenumber is 4822 209 15271.
This new version is only used in the following sets:
14PV263/01, 14PV162/01, 14PV162/05, 14PV162/07, 14PV163/05,
14PV163/05H, 14PV263/01 | 14-09-04 |
| Philips | 14PV162/01 | Option code: 00396 | From week 02/97 onwards the option code is printed on the typesticker. Always use this code ! For early sets without this information on the typesticker, the option code is: 00396 | 14-09-04 |
| Philips | 14PV162/02 | New VPS IC SDA5642-6 (pos. 7840) | Since production week 9741 a new VPS IC pos. 7840 (SDA5642-6) is introduced in production.
This IC is not compatible with the previous one. When ordering, look at the printing on the IC !
Old: SDA 5642-5 - codenumber 4822 209 32728
New: SDA 5642-6 - | 14-09-04 |
| Philips | 14PV162/02 | Option code: 00972 | From week 02/97 onwards the option code is printed on the typesticker. Always use this code !
For early sets without this information on the typesticker, the option code is: 00972 | 14-09-04 |
| Philips | 14PV162/05 | Codenumber information | A new software version (PTCP2-7) is available for the control uP (IC 7801). Service codenumber is 4822 209 15271.
This new version is only used in the following sets:
14PV263/01, 14PV162/01, 14PV162/05, 14PV162/07, 14PV163/05,
14PV163/05H, 14PV263/01 | 14-09-04 |
| Philips | 14PV162/07 | Codenumber information | A new software version (PTCP2-7) is available for the control uP (IC 7801). Service codenumber is 4822 209 15271.
This new version is only used in the following sets:
14PV263/01, 14PV162/01, 14PV162/05, 14PV162/07, 14PV163/05,
14PV163/05H, 14PV263/01 | 14-09-04 |
| Philips | 14PV163 | Codenumber information | The codenumber for the spacer between on/off switch and the knob (pos 3) is 4822 402 10702. | 14-09-04 |
|
|
| Philips | 14PV163 | Key set | The key set assy has been codified for all B-range TVCR's. This will allow to change the keys without having to change the complete frame. Servicenr. 4822 410 11075 - Key set for:
14PV263/01/02/08/13 - 14PV264/39 - 14PV163/05 - 14PV172/01/05/08/13/39 - | 14-09-04 |
| Philips | 14PV163 | Reverts to st/by at sw on | Sw tr7352 in middle of pcb | 14-09-04 |
| Philips | 14PV163 | Spare part information | Sets produced from week 9608 until 9647. Motor holder with reverse prism included:
In sets produced before week 9647 the reverse prism is a fixed part of the chassis and not available as a spare part.
From week 9647 onwards a motor holder (pos.40) with | 14-09-04 |
| Philips | 14PV163/05 | Codenumber information - new software | A new software version (PTCP2-7) is available for the control uP (IC 7801). Service codenumber is 4822 209 15271.
This new version is only used in the following sets:
14PV263/01, 14PV162/01, 14PV162/05, 14PV162/07, 14PV163/05,
14PV163/05H, 14PV263/01 | 14-09-04 |
| Philips | 14PV163/05 | Line pairing on off air pics - ok on pback | Dist at vid o/p from if - tuner faulty type U944C-IEC | 14-09-04 |
| Philips | 14PV163/05 | Reverts to st/by aft a few mins | Caused by problem triggering prot cct. Usually D6513 BAV21 flyback boost cap in FOP stage - use BYD33J in lieu | 14-09-04 |
| Philips | 14PV163/05H | Codenumber information - new software | A new software version (PTCP2-7) is available for the control uP (IC 7801). Service codenumber is 4822 209 15271.
This new version is only used in the following sets:
14PV263/01, 14PV162/01, 14PV162/05, 14PV162/07, 14PV163/05,
14PV163/05H, 14PV263/01 | 14-09-04 |
| Philips | 14PV164/05 | Dead with LOP Tr s/c | Line dr w/frm low amplitude to LOPtr due to leaky Tr7205 BC848B | 14-09-04 |
| Philips | 14PV170 | Key set | The key set assy has been codified for all B-range TVCR's. This will allow to change the keys without having to change the complete frame.
Servicenr. 4822 410 11069 - Key set for: 14PV162/01/02/05/07/08/13/58 - 14PV170/05 - 14TVCR240/01N. | 14-09-04 |
| Philips | 14PV170 | OSD missing | Replaced faulty 7.5MHz coil 1802 on main Video P.C.B. ( No osc. on pins 42 and 43 of I.C. 7801 was the clue ) Philips Part No. 4822 157 712 89 | 14-09-04 |
| Philips | 14PV170/05 | Deck shuffles at sw on , st/by LED goes out then repeats | LOPTx faulty | 14-09-04 |
| Philips | 14PV170/05 | No pic & tape stuck with mechs pulsing & led flashing | Dis lop stage got mechs working - LOPTx faulty | 14-09-04 |
| Philips | 14PV170/05 | To select tuning mode | Press "Stop" & "Vol-" together on set to eneter tuning | 14-09-04 |
| Philips | 14PV172 | Calling installation menu | The installation menu is activated by the following procedure:
- switch on the set by means of the stop key.
- Press simutaneously the "stop" key and the "volume -" key on the set. | 14-09-04 |
| Philips | 14PV172 | Codenumber correction for deck-up (IC7410) | The codenumber for the deckprocessor was wrong in the first Service Manual (4822 726 15451). In service information TVCR96-01 and in the new manual the correct codenumber is given. The codenumber for the deck-up for sets with non-turbo drive is:
4822 20 | 14-09-04 |
| Philips | 14PV172 | Key set | The key set assy has been codified for all B-range TVCR's. This will allow to change the keys without having to change the complete frame. Servicenr. 4822 410 11075 - Key set for:
14PV263/01/02/08/13 - 14PV264/39 - 14PV163/05 - 14PV172/01/05/08/13/39 - | 14-09-04 |
| Philips | 14PV172 | Memory erase procedure | The contents of the memory can only be cleared via the service mode. This option is not available for end users. (Risc of destroying option codes).
Service mode: press "STOP" on Remote Control and "PLAY" on the set for 5 seconds. Select the second page | 14-09-04 |
| Philips | 14PV172 | Modification | From production week 9725, the IC's SDA5649, SDA5649x and SDA5648 are replaced by a SDA5650 (4822 209 15504).
This new IC is fully compatible with the others, but has better characteristics. In addition to this modification, R3812 on the small signal bo | 14-09-04 |
| Philips | 14PV172 | Spare part information | If the lever inside the mains-switch is broken, the switch doesn't remain in the "ON" position.
Solution: replace the switch by a new one. Improved switches of a newer production range are on stock. (4822 276 13542) | 14-09-04 |
| Philips | 14PV172 | Start up problems | When the set is switched on by the mains-switch while a cassette is in the set, the front LED starts blinking, but the set doesn't start.
Solution:
Check the primary voltage (Ubat) and adjust this for 14" sets to exactly 101.5 Volt. (See chapter 3.1.1 | 14-09-04 |